ACTUATOR FOR DAMPERSTy p e 2 2 5Actuator with rotation drive5 NmFor the application withDampersValvesother regulatory func...
2                   SUMMARY, TYPE 225                                                             2    ● = Standard       ...
225-230T-05, 225-230T-05-P5, 225-230T-05-S2                                                                               ...
4                   225-230T-05, 225-230T-05-P5, 225-230T-05-S2     1                                                     ...
225-024T-05, 225-024T-05-P5, 225-024T-05-S2                                                                               ...
6                   225-024T-05, 225-024T-05-P5, 225-024T-05-S2     1                                                     ...
225C-024T-05, 225C-024T-05-S2                                                                                             ...
8                   225C-024T-05, 225C-024T-05-S2     1                                                                Adj...
225S-230T-05, 225S-230T-05-P5, 225S-230T-05-S2                                                                            ...
10                   225S-230T-05, 225S-230T-05-P5, 225S-230T-05-S2      1                                                ...
225S-024T-05, 225S-024T-05-P5, 225S-024T-05-S2                                                                            ...
12                   225S-024T-05, 225S-024T-05-P5, 225S-024T-05-S2      1                                                ...
225CS-024T-05, 225CS-024T-05-S2                                                                                           ...
14                   225CS-024T-05, 225CS-024T-05-S2      1                                                               ...
SPECIFIC CHARACTERISTICS OF CONTINUOUS CONTROL 15                              Wiring configuration and recommended cable ...
YOUR WAY TO GRUNER                                                                 Stuttgart                A8            ...
Upcoming SlideShare
Loading in …5
×

Damper Servomotorları Gruner d 225_en

862 views

Published on

Damper Servomotorları Gruner d 225_en

Published in: Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total views
862
On SlideShare
0
From Embeds
0
Number of Embeds
2
Actions
Shares
0
Downloads
4
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

Damper Servomotorları Gruner d 225_en

  1. 1. ACTUATOR FOR DAMPERSTy p e 2 2 5Actuator with rotation drive5 NmFor the application withDampersValvesother regulatory functions Page: Content: 2 Summary actuators, Type 225 3 - 14 Technical characteristics 15 Specific characteristic of continuous control 16 Your way to Gruner native ly Alter GR UNER – he Fr T iendGRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  2. 2. 2 SUMMARY, TYPE 225 2 ● = Standard -S P5 S2 S2 P5 05 05 5- 5- 5- 5- ❍ = Optional 5 5 T- T- -0 -0 -0 -0 -0 -0 24 24 0T 0T 4T 4T 4T 0T -0 -0 23 23 02 02 02 23 5C 5C 5- 5- 5- 5- 5- 5- Type 22 22 22 22 22 22 22 22 Torque 5Nm 5Nm 5Nm 5Nm 5Nm 5Nm 5Nm 5Nm Running time (in seconds) 60...120 60...120 60...120 60...120 60...120 60...120 60...120 60...120 Control Tri-state ● ● ● ● ● ● On/Off ● ● ● ● ● ● Continuous control ● ● (0) 2-10 VDC or (0) 4-20 mA Connecting Voltage 24 VAC/DC ● ● ● ● ● 230 VAC ● ● ● Options Potentiometer ● ● Feedback signal (continuous) ● ● Auxiliary switch ● ● ● Page 3-4 3-4 3-4 5-6 5-6 5-6 7-8 7-8 S2 5 2 2 5 ● = Standard -P -S -S -P 5- 5 -0 05 05 05 05 05 05 -0 ❍ = Optional 4T 4T T- T- T- T- T- T- 02 30 30 24 24 24 30 02 S- -2 -2 -0 -0 -0 -2 S- 5C 5S 5S 5S 5S 5S 5S 5C Type 22 22 22 22 22 22 22 22 Torque 5Nm 5Nm 5Nm 5Nm 5Nm 5Nm 5Nm 5Nm Running time (in seconds) 20...35 20...35 20...35 20...35 20...35 20...35 20...35 20...35 Control Tri-state ● ● ● ● ● ● On/Off ● ● ● ● ● ● Continuous control ● ● (0) 2-10 VDC or (0) 4-20 mA Connecting Voltage 24 VAC/DC ● ● ● ● ● 230 VAC ● ● ● Options Potentiometer ● ● Feedback signal (continuous) ● ● Auxiliary switch ● ● ● Page 9 - 10 9 - 10 9 - 10 11 - 12 11 - 12 11 - 12 13 - 14 13 - 14 GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  3. 3. 225-230T-05, 225-230T-05-P5, 225-230T-05-S2 3 Applications To regulate dampers, valves or other regulatory functions: • sturdy drive • position indication • maintenance-free • angle of rotation changeable from outside • nominal torque 4 Nm • auxiliary switch adjustable from outside • start-up torque 6 Nm • electromagnetic compatibility tested Technical characteristics Control On/Off + Tri-state Connecting voltage 80...265 VAC (50/60 Hz) / DC Power consumption 1.5 W / 2.0 VA Angle of rotation max. 95° (changeable from outside) Direction of rotation changeable from inside Running time 60...120 s @ 90° Torque 5 Nm Auxiliary switch max. 2, adjustable from outside Switching power auxiliary switch 250 VAC / 5 (2.5) A Potentiometer 4.7 kΩ (0.2W) Connection terminal for cable 0,5...1,5 mm2 Safety class II Protection IP42 Dimensions 145 x 65 x 61 mm Ambient temperature -30...+50°C Maintenance maintenance-free CE 73/23/EWG, 89/336/EWG Weight ca. 500 g 225-230T-05 225-230T-05-P5 225-230T-05-S2 Connection scheme Connection scheme Connection scheme 1 2 3 1 2 3 1 2 3 1 2 3 On / Off N N N N L L 1 2 3 L L 1 2 3 1 2 3 S1 S2 Tri-State Potentiometer 1 2 3 1 2 3 N N L Auxiliary switches LGRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  4. 4. 4 225-230T-05, 225-230T-05-P5, 225-230T-05-S2 1 Adjustment of the angle of rotation (fig. 1) Both end stops are adjusted to 0 (0°) and 1 (90°). For smaller rotation angles, loosen the screws at the metal end stop, adjust the end stops as requested, and fasten the screws again. Fixing of the shaft (fig. 1) by the locking clamp to the damper shaft: ❑ 8...12 mm ∅ 8...16 mm Adjustment of the auxiliary switch (fig. 2) 2 The scale at the adjusting knob corresponds to a percentage graduation, related to 0° - 90°. 1) End stop is set to “0“: Switch off the motor and choose the requested switching position by turning the knob to the right, i.e. “2“ = 20%. 2) End stop is set to “1“: Switch off the motor and choose the requested switching position by turning the knob to the left, i.e. “8“ = 20%. Direction of rotation switch (On/Off) (fig. 3) Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 2+3 Supply 2 Supply R / CW 2 Supply 2+3 Supply 3 Direction of rotation switch (Tri-state) (fig. 3) L / CCW R / CW Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW R / CW L / CCW 3 Supply 2 Supply R / CW 2 Supply 3 Supply Technical drawing 225-230T-05 all dimensions in mm GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  5. 5. 225-024T-05, 225-024T-05-P5, 225-024T-05-S2 5 Applications To regulate dampers, valves or other regulatory functions: • sturdy drive • position indication • maintenance-free • angle of rotation changeable from outside • nominal torque 4 Nm • auxiliary switch adjustable from outside • start-up torque 6 Nm • electromagnetic compatibility tested Technical characteristics Control On/Off + Tri-state Connecting voltage 24 VAC (50/60 Hz) / DC ±20% Power consumption 1.0 W / 2.0 VA Angle of rotation max. 95° (changeable from outside) Direction of rotation changeable from inside Running time 60...120 s @ 90° Torque 5 Nm Auxiliary switch max. 2, adjustable from outside Switching power auxiliary switch 250 VAC / 5 (2.5) A Potentiometer 4.7 kΩ (0.2 W) Connection terminal for cable 0,5...1,5 mm2 Safety class III Protection IP42 Dimensions 145 x 65 x 61 mm Ambient temperature -30...+50°C Maintenance maintenance-free CE 73/23/EWG, 89/336/EWG Weight ca. 500 g 225-024T-05 225-024T-05-P5 225-024T-05-S2 Connection scheme Connection scheme Connection scheme 1 2 3 1 2 3 1 2 3 1 2 3 On / Off 1 2 3 1 2 3 1 2 3 S1 S2 Tri-State Potentiometer 1 2 3 1 2 3 Auxiliary switchesGRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  6. 6. 6 225-024T-05, 225-024T-05-P5, 225-024T-05-S2 1 Adjustment of the angle of rotation (fig. 1) Both end stops are adjusted to 0 (0°) and 1 (90°). For smaller rotation angles, loosen the screws at the metal end stop, adjust the end stops as requested, and fasten the screws again. Fixing of the shaft (fig. 1) by the locking clamp to the damper shaft: ❑ 8...12 mm ∅ 8...16 mm Adjustment of the auxiliary switch (fig. 2) 2 The scale at the adjusting knob corresponds to a percentage graduation, related to 0° - 90°. 1) End stop is set to “0“: Switch off the motor and choose the requested switching position by turning the knob to the right, i.e. “2“ = 20%. 2) End stop is set to “1“: Switch off the motor and choose the requested switching position by turning the knob to the left, i.e. “8“ = 20%. Direction of rotation switch (On/Off) (fig. 3) Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 2+3 Supply 2 Supply R / CW 2 Supply 2+3 Supply 3 Direction of rotation switch (Tri-state) (fig. 3) L / CCW R / CW Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 3 Supply 2 Supply L / CCW R / CW R / CW 2 Supply 3 Supply Technical drawing 225-024T-05 all dimensions in mm GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  7. 7. 225C-024T-05, 225C-024T-05-S2 7 Applications To regulate dampers, valves or other regulatory functions: • sturdy drive • position indication • maintenance-free • angle of rotation changeable from outside • nominal torque 4 Nm • auxiliary switch adjustable from outside • start-up torque 6 Nm • electromagnetic compatibility tested Technical characteristics Control Continuous control Control signal Y 0...10 VDC or 2...10 VDC (Standard) or 0...20 mA or 4...20 mA Feedback signal U 0...10 VDC or 2...10 VDC (Standard) Connecting voltage 24 VAC (50/60 Hz) / DC ±20% Power consumption 1.5 W / 2.5 VA 225C-024T-05 Angle of rotation max. 95° (changeable from outside) Direction of rotation changeable from inside Connection scheme Running time 60...120 s @ 90° (Continuous control) Torque 5 Nm Auxiliary switch max. 2, adjustable from outside Switching power auxiliary switch 250 VAC / 5 (2.5) A, change-over switch 1 2 3 4 Connection terminal for cable 0,5...1,5 mm2 Safety class III Y U Protection IP42 Dimensions 145 x 65 x 61 mm Ambient temperature -30...+50°C 225C-024T-05-S2 Maintenance maintenance-free CE 73/23/EWG, 89/336/EWG Connection scheme Weight ca. 500 g (Continuous control) 1 2 3 4 Y U S1 S2 1 2 3 1 2 3GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  8. 8. 8 225C-024T-05, 225C-024T-05-S2 1 Adjustment of the angle of rotation (fig. 1) Both end stops are adjusted to 0° and 90°. For smaller rotation angles, loosen the screws at the metal end stop, adjust the end stops as requested, and fasten the screws again. Fixing of the shaft (fig. 1) by the locking clamp to the damper shaft: ❑ 8...12 mm ∅ 8...16 mm Adjustment of the auxiliary switch (fig. 2) 2 The scale at the adjusting knob corresponds to a percentage graduation, related to 0° - 90°. 1) End stop is set to “0“: Switch off the motor and choose the requested switching position by turning the knob to the right, i.e. “2“ = 20%. 2) End stop is set to “1“: Switch off the motor and choose the requested switching position by turning the knob to the left, i.e. “8“ = 20%. Adjustment of the functional switches (fig. 3) OFF ON Direction of rotation clockwise (0...90°) 3 - counter clockwise (90...0°) - 3 Control signal Y 3 ON 2...10 VDC (Standard) 1, 2 - 0...10 VDC 2 1 OFF 1 2 3 4 4...20 mA 1 2 0...20 mA - 1, 2 Teach-in of range of angle Active - 4 Inactive 4 - All switches are set to OFF by factory default. See page 15 for further instructions concerning teach-in. Technical drawing 225C-024T-05 all dimensions in mm GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  9. 9. 225S-230T-05, 225S-230T-05-P5, 225S-230T-05-S2 9 Applications To regulate dampers, valves or other regulatory functions: • sturdy drive • position indication • maintenance-free • angle of rotation changeable from outside • nominal torque 4 Nm • auxiliary switch adjustable from outside • start-up torque 6 Nm • electromagnetic compatibility tested Technical characteristics Control On/Off + Tri-state Connecting voltage 80...265 VAC (50/60 Hz) / DC Power consumption 2.0 W / 3.5 VA Angle of rotation max. 95° (changeable from outside) Direction of rotation changeable from inside Running time 20...35 s @ 90° Torque 5 Nm Auxiliary switch max. 2, adjustable from outside Switching power auxiliary switch 250 VAC / 5 (2.5) A Potentiometer 4.7 kΩ (0.2 W) Connection terminal for cable 0,5...1,5 mm2 Safety class II Protection IP42 Dimensions 145 x 65 x 61 mm Ambient temperature -30...+50°C Maintenance maintenance-free CE 73/23/EWG, 89/336/EWG Weight ca. 500 g 225S-230T-05 225S-230T-05-P5 225S-230T-05-S2 Connection scheme Connection scheme Connection scheme 1 2 3 1 2 3 1 2 3 1 2 3 On / Off N N N N L L 1 2 3 L L 1 2 3 1 2 3 S1 S2 Tri-State Potentiometer 1 2 3 1 2 3 N N L Auxiliary switches LGRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  10. 10. 10 225S-230T-05, 225S-230T-05-P5, 225S-230T-05-S2 1 Adjustment of the angle of rotation (fig. 1) Both end stops are adjusted to 0 (0°) and 1 (90°). For smaller rotation angles, loosen the screws at the metal end stop, adjust the end stops as requested, and fasten the screws again. Fixing of the shaft (fig. 1) by the locking clamp to the damper shaft: ❑ 8...12 mm ∅ 8...16 mm Adjustment of the auxiliary switch (fig. 2) 2 The scale at the adjusting knob corresponds to a percentage graduation, related to 0° - 90°. 1) End stop is set to “0“: Switch off the motor and choose the requested switching position by turning the knob to the right, i.e. “2“ = 20%. 2) End stop is set to “1“: Switch off the motor and choose the requested switching position by turning the knob to the left, i.e. “8“ = 20%. Direction of rotation switch (On/Off) (fig. 3) Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 2+3 Supply 2 Supply R / CW 2 Supply 2+3 Supply 3 Direction of rotation switch (Tri-state) (fig. 3) L / CCW R / CW Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 3 Supply 2 Supply L / CCW R / CW R / CW 2 Supply 3 Supply Technical drawing 225S-230T-05 all dimensions in mm GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  11. 11. 225S-024T-05, 225S-024T-05-P5, 225S-024T-05-S2 11 Applications To regulate dampers, valves or other regulatory functions: • sturdy drive • position indication • maintenance-free • angle of rotation changeable from outside • nominal torque 4 Nm • auxiliary switch adjustable from outside • start-up torque 6 Nm • electromagnetic compatibility tested Technical characteristics Control On/Off + Tri-state Connecting voltage 24 VAC (50/60 Hz) / DC ±20% Power consumption 2.0 W / 3.0 VA Angle of rotation max. 95° (changeable from outside) Direction of rotation changeable from inside Running time 20...35 s @ 90° Torque 5 Nm Auxiliary switch max. 2, adjustable from outside Switching power auxiliary switch 250 VAC / 5 (2.5) A Potentiometer 4.7 kΩ (0.2 W) Connection terminal for cable 0,5...1,5 mm2 Safety class III Protection IP42 Dimensions 145 x 65 x 61 mm Ambient temperature -30...+50°C Maintenance maintenance-free CE 73/23/EWG, 89/336/EWG Weight ca. 500 g 225S-024T-05 225S-024T-05-P5 225S-024T-05-S2 Connection scheme Connection scheme Connection scheme 1 2 3 1 2 3 1 2 3 1 2 3 On / Off 1 2 3 1 2 3 1 2 3 S1 S2 Tri-State Potentiometer 1 2 3 1 2 3 Auxiliary switchesGRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  12. 12. 12 225S-024T-05, 225S-024T-05-P5, 225S-024T-05-S2 1 Adjustment of the angle of rotation (fig. 1) Both end stops are adjusted to 0 (0°) and 1 (90°). For smaller rotation angles, loosen the screws at the metal end stop, adjust the end stops as requested, and fasten the screws again. Fixing of the shaft (fig. 1) by the locking clamp to the damper shaft: ❑ 8...12 mm ∅ 8...16 mm Adjustment of the auxiliary switch (fig. 2) 2 The scale at the adjusting knob corresponds to a percentage graduation, related to 0° - 90°. 1) End stop is set to “0“: Switch off the motor and choose the requested switching position by turning the knob to the right, i.e. “2“ = 20%. 2) End stop is set to “1“: Switch off the motor and choose the requested switching position by turning the knob to the left, i.e. “8“ = 20%. Direction of rotation switch (On/Off) (fig. 3) Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 2+3 Supply 2 Supply R / CW 2 Supply 2+3 Supply 3 Direction of rotation switch (Tri-state) (fig. 3) L / CCW R / CW Direction of rotation Clockwise (0...90°) Counter clockwise (90...0°) Switch position L / CCW 3 Supply 2 Supply L / CCW R / CW R / CW 2 Supply 3 Supply Technical drawing 225S-024T-05 all dimensions in mm GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  13. 13. 225CS-024T-05, 225CS-024T-05-S2 13 Applications To regulate dampers, valves or other regulatory functions: • sturdy drive • position indication • maintenance-free • angle of rotation changeable from outside • nominal torque 4 Nm • auxiliary switch adjustable from outside • start-up torque 6 Nm • electromagnetic compatibility tested Technical characteristics Control Continuous control Control signal Y 0...10 VDC or 2...10 VDC (Standard) or 0...20 mA or 4...20 mA Feedback signal U 0...10 VDC or 2...10 VDC (Standard) Connecting voltage 24 VAC (50/60 Hz) / DC ±20% Power consumption 2,5 W / 4,0 VA 225CS-024T-05 Angle of rotation max. 95° (changeable from outside) Direction of rotation changeable from inside Connection scheme Running time 20...35 s @ 90° (Continuous control) Torque 5 Nm Auxiliary switch max. 2, adjustable from outside Switching power auxiliary switch 250 VAC / 5 (2.5) A, change-over switch 1 2 3 4 Connection terminal for cable 0,5...1,5 mm2 Safety class III Y U Protection IP42 Dimensions 145 x 65 x 61 mm Ambient temperature -30...+50°C 225CS-024T-05-S2 Maintenance maintenance-free CE 73/23/EWG, 89/336/EWG Connection scheme Weight ca. 500 g (Continuous control) 1 2 3 4 Y U S1 S2 1 2 3 1 2 3GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  14. 14. 14 225CS-024T-05, 225CS-024T-05-S2 1 Adjustment of the angle of rotation (fig. 1) Both end stops are adjusted to 0 (0°) and 1 (90°). For smaller rotation angles, loosen the screws at the metal end stop, adjust the end stops as requested, and fasten the screws again. Fixing of the shaft (fig. 1) by the locking clamp to the damper shaft: ❑ 8...12 mm ∅ 8...16 mm Adjustment of the auxiliary switch (fig. 2) 2 The scale at the adjusting knob corresponds to a percentage graduation, related to 0° - 90°. 1) End stop is set to “0“: Switch off the motor and choose the requested switching position by turning the knob to the right, i.e. “2“ = 20%. 2) End stop is set to “1“: Switch off the motor and choose the requested switching position by turning the knob to the left, i.e. “8“ = 20%. Adjustment of the functional switches (fig. 3) OFF ON Direction of rotation clockwise (0...90°) 3 - counter clockwise (90...0°) - 3 Control signal Y 3 2...10 VDC (Standard) 1, 2 - ON 0...10 VDC 2 1 OFF 4...20 mA 1 2 1 2 3 4 0...20 mA - 1, 2 Teach-in of range of angle Active - 4 Inactive 4 - All switches are set to OFF by factory default. See page 15 for further teach-in instructions. Technical drawing 225CS-024T-05 all dimensions in mm GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.de PF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de 40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  15. 15. SPECIFIC CHARACTERISTICS OF CONTINUOUS CONTROL 15 Wiring configuration and recommended cable length max. cable length max. cable length transformer transformer current of set valve selector actuator current cable cross section max. cable length cable resistance cable length * cable cross section For several actuators switched in parallel the max. cable length must be divided by the number of actuators. * Cable cross section for terminal up to 1,5 mm 2 Teach-in of range of angle > 30° ON OFF 1. Actuator stand by 1 2 3 4 2. Adjusting mechanical endstops 3. Switch ON DIP 4 4. Actuator starts teach-in process of range of angle (60...120 s) 5. Turn OFF DIP 4 6. Y now corresponds to the teached-in angleGRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved
  16. 16. YOUR WAY TO GRUNER Stuttgart A8 München Balingen Karlsruhe Schömberg Wehingen A81 Freudenstadt B27 Gosheim Denkingen Tuttlingen Frittlingen Strasbourg Rottweil Spaichingen B14 Aldingen Schramberg Offenburg 34 B27 A5 B33 Freiburg Donaueschingen B31 Singen Zürich Basel N1 N3GRUNER AG Tel. (++49) 74 26 / 948 - 0 http://www.gruner.dePF 1149, D-78560 Wehingen Fax (++49) 74 26 / 948 - 200 E-Mail: info@gruner.de40/07 · 225EN · Copyright by Gruner AG ·Technical changes are reserved

×