XLW (PC) Auto Tensile Tester is professionally applicable to the determination of force properties of various flexible packaging materials, with high precision (better than 0.5% of reading accuracy) and multiple test ranges. The instrument is designed with 7independent test modes and could perform tests at seven different test speeds to meet various test conditions. Intelligent software facilitates to operate the instrument and provides data analysis and comparison functions.
XLW (EC) Auto Tensile Tester can be used to measure tensile, peeling, deformation, tearing, heat sealing, adhesive, puncture force, opening force and low speed unwrapping force as well as other performance of plastic films, composite materials, soft package materials, plastic flexible tube, adhesives, adhesive tape, label stickers, medical plasters, release paper, protection films, combined caps, aluminum foil, diaphragm, back sheets, non-woven fabrics, rubber, and paper, and etc.
1% of reading value effectively ensures the accuracy of test results
7 independent test modes are available, including tensile strength, peeling force, tearing force, heat seal strength and other force properties of flexible packages
Different ranges of load cells and 7 distinct test speeds to meet different test requirements
The instrument is controlled by micro-computer with menu interface, PVC operation panel and large LCD display
1% of reading value effectively ensures the accuracy of test results
2 independent test modes are available, including tensile strength and peeling force to meet the distinct requirements of users
3 kinds of testing data provided for each test i.e. Maximum Value, Minimum Value and Average Value. Group data analysis is also available.
1% of reading value effectively ensures the accuracy of test results7 independent test modes are available, including tensile strength, peeling force, tearing force, heat seal strength and other force properties of flexible packagesDifferent ranges of load cells and 7 distinct test speeds to meet different test requirements
Better than 0.5% of reading value effectively ensures accurate test results
Multiple testing modes are available, including tensile strength, deformation, peeling and tearing, etc.
Stress at defined elongation, elastic modulus and stress and strain etc. could be analyzed
1200mm extra-long stroke satisfies the test needs of various materials with extreme deformation rate
MED-01 Medical Packaging Tester is professionally applicable to the determination of force properties of various medical packaging materials, with high precision (better than 0.5% of reading accuracy) and multiple test ranges. The instrument is designed with 16 independent test modes and bidirectional test mode of stretching and compression, which can meet various test requirements.
The document provides material control standards for physical property testing of synthetic materials. It lists test items, standards, units of measurement, and test methods for thickness, tensile strength, tearing strength, elongation, bursting strength, abrasion resistance, color fastness, and other properties. The tests are conducted in both the machine (MD) and cross (CD) directions. Remarks note that MD refers to the warp/machine direction and CD to the weft/cut direction.
Food Packaging Testing Equipment by PackTestRohit Chawla
PackTest is India's leading manufacturer and exporter of quality testing equipment for the packaging industry. They offer a wide range of equipment to test various material properties such as compression, tensile, burst strength, thickness, pinholes, seal strength, permeability, friction, print quality, packaging integrity, and more. Their equipment is used for quality assurance, research and development, and packaging development in industries that manufacture or use packaging materials.
XLW (EC) Auto Tensile Tester can be used to measure tensile, peeling, deformation, tearing, heat sealing, adhesive, puncture force, opening force and low speed unwrapping force as well as other performance of plastic films, composite materials, soft package materials, plastic flexible tube, adhesives, adhesive tape, label stickers, medical plasters, release paper, protection films, combined caps, aluminum foil, diaphragm, back sheets, non-woven fabrics, rubber, and paper, and etc.
1% of reading value effectively ensures the accuracy of test results
7 independent test modes are available, including tensile strength, peeling force, tearing force, heat seal strength and other force properties of flexible packages
Different ranges of load cells and 7 distinct test speeds to meet different test requirements
The instrument is controlled by micro-computer with menu interface, PVC operation panel and large LCD display
1% of reading value effectively ensures the accuracy of test results
2 independent test modes are available, including tensile strength and peeling force to meet the distinct requirements of users
3 kinds of testing data provided for each test i.e. Maximum Value, Minimum Value and Average Value. Group data analysis is also available.
1% of reading value effectively ensures the accuracy of test results7 independent test modes are available, including tensile strength, peeling force, tearing force, heat seal strength and other force properties of flexible packagesDifferent ranges of load cells and 7 distinct test speeds to meet different test requirements
Better than 0.5% of reading value effectively ensures accurate test results
Multiple testing modes are available, including tensile strength, deformation, peeling and tearing, etc.
Stress at defined elongation, elastic modulus and stress and strain etc. could be analyzed
1200mm extra-long stroke satisfies the test needs of various materials with extreme deformation rate
MED-01 Medical Packaging Tester is professionally applicable to the determination of force properties of various medical packaging materials, with high precision (better than 0.5% of reading accuracy) and multiple test ranges. The instrument is designed with 16 independent test modes and bidirectional test mode of stretching and compression, which can meet various test requirements.
The document provides material control standards for physical property testing of synthetic materials. It lists test items, standards, units of measurement, and test methods for thickness, tensile strength, tearing strength, elongation, bursting strength, abrasion resistance, color fastness, and other properties. The tests are conducted in both the machine (MD) and cross (CD) directions. Remarks note that MD refers to the warp/machine direction and CD to the weft/cut direction.
Food Packaging Testing Equipment by PackTestRohit Chawla
PackTest is India's leading manufacturer and exporter of quality testing equipment for the packaging industry. They offer a wide range of equipment to test various material properties such as compression, tensile, burst strength, thickness, pinholes, seal strength, permeability, friction, print quality, packaging integrity, and more. Their equipment is used for quality assurance, research and development, and packaging development in industries that manufacture or use packaging materials.
This document provides product information about MOLYKOTE BG 555 Low Noise Grease. It has a wide service temperature range from -40 to 150°C, long performance life, excellent low temperature properties, and noise suppressing and anti-rust properties. Typical properties testing shows it has a high dropping point, good corrosion prevention, and can last over 4000 hours in life performance testing at 125°C. It is suitable for use in bearings at elevated temperatures and helps extend intervals between grease replacement.
This lecture describes the factors important for the quality assurance of adhesive joining; it gives information about the destructive and non-destructive testing methods for the quality control of adhesive joining. General background in production engineering and material science, some knowledge of mechanics and polymer science is assumed.
This document summarizes a universal testing machine (UTM) that can perform various mechanical tests on packaging materials and products. It lists several models of the mini-UTM with varying capacities and resolutions. The UTM has a computerized control system and optional modules/fixtures that allow it to conduct tests such as cap snap/pull, peel strength, seal strength, elongation, and top load strength. Custom fixtures can also be designed for unique test requirements.
This document provides information on various tests for food packaging, including the purpose and importance of packaging testing. It discusses how testing new packaging designs can save time and money by identifying potential issues. It then classifies packaging tests into material tests and package tests, and further into chemical and mechanical tests. Several specific mechanical tests are described in detail, including GSM (grammage), thickness, pinhole testing of aluminum foil, peel bonding (delamination), seal strength, permeability, coefficient of friction, ink rub/scuff testing, and compression/burst testing of pouches. Standards for conducting each test are provided. The document serves as an educational reference on packaging testing methods.
Techniques For Measuring Adhesion Abrasion Durability Of Coatings Inks By Sco...SabreenGroup
This document discusses techniques for measuring adhesion and abrasion durability of coatings and inks. It describes several common adhesion test methods, including the tape test outlined in ASTM D 3359 and pull-off adhesion tests using instruments described in ASTM D 4541. The tape test is a simple qualitative method to assess minimum adhesion levels, but it has limitations and can produce variable results depending on the tape used. Pull-off adhesion tests require specialized equipment and also may produce different readings based on the instrument used. The document emphasizes that proper testing is important to ensure coatings and inks meet specifications and help solve manufacturing problems.
This product is an air-curing dry lubricant anti-friction coating composed of solid lubricants, solvents, and a binder. It provides avoidance of stick-slip, high ageing resistance, and is suitable for metal/metal combinations with slow to medium fast movements and high loads. The coating is applied by spraying or brushing in a dry film thickness of 5 to 20μm and cures after 5 minutes at 23°C. It has a usable life of 24 months when stored at or below 20°C.
This document provides product information for two high performance greases - MOLYKOTE® PG 30 L and MOLYKOTE® EM 30 LG. The greases contain no lead or nickel and have a high load carrying capacity, making them suitable for lubricating plastic, plastic, plastic/metal, and rubber/metal combinations with medium to heavy loads and low to medium speeds. The document lists typical properties such as consistency, density, service temperature range, and test results for properties like oxidation resistance, corrosion protection, and oil separation. Usage instructions and limitations, packaging, storage, and warranty information are also provided.
Molykote® G-6000 is a high-performance bearing grease for extreme high temperatures from -40 to +200°C. It has a polyurea thickener and synthetic phenylether base oil, providing excellent mechanical stability and corrosion prevention. The grease is suitable for bearings operating at high temperatures and under high stress.
Semi-Finished Engineering Plastic Products. TECAFORM is a versatile engineering plastic with high strength and dimensional stability. It is suitable for a wide range of applications due to its resistance to organic solvents and outstanding machinability. TECAFORM has good sliding and abrasion behavior and low water absorption properties. The document provides information on different grades of TECAFORM and their properties, as well as specifications for TECAFORM tubes in various diameters and tolerances.
The document discusses a ring crush tester, which is used to test the rigidity and stiffness of paper by measuring its ring crush value. A higher ring crush value indicates stiffer paper that can make stronger corrugated cartons. The ring crush tester is essential for paper mills and other heavy paper users to ensure paper quality. Specifications of the electro-hydraulic and digital models are provided.
This study evaluated the degree of conversion (DC) and plasticization of a pit and fissure sealant (Fluroshield) and a flowable composite (Permaflo) when cured for either 20 or 60 seconds. The key findings were:
1) Permaflo had a higher DC than Fluroshield at both curing times. Extended curing (60 seconds) increased the DC of Permaflo but not Fluroshield.
2) Fluroshield showed higher plasticization (hardness decrease after ethanol storage) than Permaflo. Extended curing did not decrease plasticization for either material.
3) There was a low negative correlation between DC and plasticization, suggesting DC
The document provides information on the thermoplastic polymer polyoxymethylene (POM) including its delivery program, properties, applications, and chemical resistance. POM has a continuous service temperature up to 100°C, high surface strength surpassed by few materials, and good sliding and wear resistance due to its strength and smooth surface. It has applications in bearings, fittings, gears, pumps, and textiles. POM demonstrates resistance to many chemicals at room temperature and 60°C but is not resistant to strong acids or oxidizing agents.
HTT-L1 Hot Tack Tester is applicable in hot tack and heat seal performance tests for plastic film, laminated film and other packaging film. Meanwhile, it is applicable in peel, shear, tension and other test items for adhesive, adhesive tape, laminated film, plastic film, paper and other flexible materials.
XLW (PC) Auto Tensile Tester can be used to determine physical mechanical properties of plastic films, laminated materials, flexible packaging materials, plastic flexible tube, adhesives, adhesive tapes, pressure sensitive tapes, and adhesive bandage (plaster) etc.
Robert Joyce presented on FibreTuff, a wood flour and polyolefin composite pellet that offers improved performance over traditional composites. FibreTuff pellets have very low moisture content and increased adhesion between fibers and polymer. This leads to injection molded parts with better dimensional stability, thermal properties, and moisture resistance. The presentation provided details on biomass feedstocks, FibreTuff processing and properties, and applications for material replacement using advanced molding techniques like rapid thermal cycling and fluid injection molding.
This document specifies requirements for cold-reduced carbon steel sheets and coils, including three quality categories (commercial, drawing, and deep drawing), temper grades, surface finishes, mechanical properties, dimensional tolerances, and other specifications. Key information includes tensile strength and elongation requirements that vary based on steel type, thickness, and width. Tolerances for thickness, width, and length are defined that classify steel into quality classes with different tolerance ranges.
Packaging Testing Equipment - by PackTestRohit Chawla
Company Profile and Product Catalog of PackTest.
Packaging Testing Equipment manufactured and exported by Test Techno Consultants. Marketed in India by Rohit Instruments & Testing Services. Rohit Chawla
1) The document provides information on gas chromatography components and processes.
2) It describes the purpose of various parts of a GC system like the injection port, column, detector, and data system.
3) The document also summarizes different types of columns, detectors, injection techniques, and factors that influence separations like temperature and flow.
Esta norma estabelece os critérios e requisitos para o paralelismo momentâneo de geradores de consumidores com a rede elétrica da Coelba, com operação em rampa. Inclui definições técnicas, critérios gerais e técnicos para a solicitação, projeto, instalação, operação, proteção e inspeções do sistema de paralelismo. O objetivo é permitir a conservação de energia elétrica durante horários de pico, assegurando a segurança do sistema elétrico e de outras unidades consum
This document provides product information about MOLYKOTE BG 555 Low Noise Grease. It has a wide service temperature range from -40 to 150°C, long performance life, excellent low temperature properties, and noise suppressing and anti-rust properties. Typical properties testing shows it has a high dropping point, good corrosion prevention, and can last over 4000 hours in life performance testing at 125°C. It is suitable for use in bearings at elevated temperatures and helps extend intervals between grease replacement.
This lecture describes the factors important for the quality assurance of adhesive joining; it gives information about the destructive and non-destructive testing methods for the quality control of adhesive joining. General background in production engineering and material science, some knowledge of mechanics and polymer science is assumed.
This document summarizes a universal testing machine (UTM) that can perform various mechanical tests on packaging materials and products. It lists several models of the mini-UTM with varying capacities and resolutions. The UTM has a computerized control system and optional modules/fixtures that allow it to conduct tests such as cap snap/pull, peel strength, seal strength, elongation, and top load strength. Custom fixtures can also be designed for unique test requirements.
This document provides information on various tests for food packaging, including the purpose and importance of packaging testing. It discusses how testing new packaging designs can save time and money by identifying potential issues. It then classifies packaging tests into material tests and package tests, and further into chemical and mechanical tests. Several specific mechanical tests are described in detail, including GSM (grammage), thickness, pinhole testing of aluminum foil, peel bonding (delamination), seal strength, permeability, coefficient of friction, ink rub/scuff testing, and compression/burst testing of pouches. Standards for conducting each test are provided. The document serves as an educational reference on packaging testing methods.
Techniques For Measuring Adhesion Abrasion Durability Of Coatings Inks By Sco...SabreenGroup
This document discusses techniques for measuring adhesion and abrasion durability of coatings and inks. It describes several common adhesion test methods, including the tape test outlined in ASTM D 3359 and pull-off adhesion tests using instruments described in ASTM D 4541. The tape test is a simple qualitative method to assess minimum adhesion levels, but it has limitations and can produce variable results depending on the tape used. Pull-off adhesion tests require specialized equipment and also may produce different readings based on the instrument used. The document emphasizes that proper testing is important to ensure coatings and inks meet specifications and help solve manufacturing problems.
This product is an air-curing dry lubricant anti-friction coating composed of solid lubricants, solvents, and a binder. It provides avoidance of stick-slip, high ageing resistance, and is suitable for metal/metal combinations with slow to medium fast movements and high loads. The coating is applied by spraying or brushing in a dry film thickness of 5 to 20μm and cures after 5 minutes at 23°C. It has a usable life of 24 months when stored at or below 20°C.
This document provides product information for two high performance greases - MOLYKOTE® PG 30 L and MOLYKOTE® EM 30 LG. The greases contain no lead or nickel and have a high load carrying capacity, making them suitable for lubricating plastic, plastic, plastic/metal, and rubber/metal combinations with medium to heavy loads and low to medium speeds. The document lists typical properties such as consistency, density, service temperature range, and test results for properties like oxidation resistance, corrosion protection, and oil separation. Usage instructions and limitations, packaging, storage, and warranty information are also provided.
Molykote® G-6000 is a high-performance bearing grease for extreme high temperatures from -40 to +200°C. It has a polyurea thickener and synthetic phenylether base oil, providing excellent mechanical stability and corrosion prevention. The grease is suitable for bearings operating at high temperatures and under high stress.
Semi-Finished Engineering Plastic Products. TECAFORM is a versatile engineering plastic with high strength and dimensional stability. It is suitable for a wide range of applications due to its resistance to organic solvents and outstanding machinability. TECAFORM has good sliding and abrasion behavior and low water absorption properties. The document provides information on different grades of TECAFORM and their properties, as well as specifications for TECAFORM tubes in various diameters and tolerances.
The document discusses a ring crush tester, which is used to test the rigidity and stiffness of paper by measuring its ring crush value. A higher ring crush value indicates stiffer paper that can make stronger corrugated cartons. The ring crush tester is essential for paper mills and other heavy paper users to ensure paper quality. Specifications of the electro-hydraulic and digital models are provided.
This study evaluated the degree of conversion (DC) and plasticization of a pit and fissure sealant (Fluroshield) and a flowable composite (Permaflo) when cured for either 20 or 60 seconds. The key findings were:
1) Permaflo had a higher DC than Fluroshield at both curing times. Extended curing (60 seconds) increased the DC of Permaflo but not Fluroshield.
2) Fluroshield showed higher plasticization (hardness decrease after ethanol storage) than Permaflo. Extended curing did not decrease plasticization for either material.
3) There was a low negative correlation between DC and plasticization, suggesting DC
The document provides information on the thermoplastic polymer polyoxymethylene (POM) including its delivery program, properties, applications, and chemical resistance. POM has a continuous service temperature up to 100°C, high surface strength surpassed by few materials, and good sliding and wear resistance due to its strength and smooth surface. It has applications in bearings, fittings, gears, pumps, and textiles. POM demonstrates resistance to many chemicals at room temperature and 60°C but is not resistant to strong acids or oxidizing agents.
HTT-L1 Hot Tack Tester is applicable in hot tack and heat seal performance tests for plastic film, laminated film and other packaging film. Meanwhile, it is applicable in peel, shear, tension and other test items for adhesive, adhesive tape, laminated film, plastic film, paper and other flexible materials.
XLW (PC) Auto Tensile Tester can be used to determine physical mechanical properties of plastic films, laminated materials, flexible packaging materials, plastic flexible tube, adhesives, adhesive tapes, pressure sensitive tapes, and adhesive bandage (plaster) etc.
Robert Joyce presented on FibreTuff, a wood flour and polyolefin composite pellet that offers improved performance over traditional composites. FibreTuff pellets have very low moisture content and increased adhesion between fibers and polymer. This leads to injection molded parts with better dimensional stability, thermal properties, and moisture resistance. The presentation provided details on biomass feedstocks, FibreTuff processing and properties, and applications for material replacement using advanced molding techniques like rapid thermal cycling and fluid injection molding.
This document specifies requirements for cold-reduced carbon steel sheets and coils, including three quality categories (commercial, drawing, and deep drawing), temper grades, surface finishes, mechanical properties, dimensional tolerances, and other specifications. Key information includes tensile strength and elongation requirements that vary based on steel type, thickness, and width. Tolerances for thickness, width, and length are defined that classify steel into quality classes with different tolerance ranges.
Packaging Testing Equipment - by PackTestRohit Chawla
Company Profile and Product Catalog of PackTest.
Packaging Testing Equipment manufactured and exported by Test Techno Consultants. Marketed in India by Rohit Instruments & Testing Services. Rohit Chawla
1) The document provides information on gas chromatography components and processes.
2) It describes the purpose of various parts of a GC system like the injection port, column, detector, and data system.
3) The document also summarizes different types of columns, detectors, injection techniques, and factors that influence separations like temperature and flow.
Esta norma estabelece os critérios e requisitos para o paralelismo momentâneo de geradores de consumidores com a rede elétrica da Coelba, com operação em rampa. Inclui definições técnicas, critérios gerais e técnicos para a solicitação, projeto, instalação, operação, proteção e inspeções do sistema de paralelismo. O objetivo é permitir a conservação de energia elétrica durante horários de pico, assegurando a segurança do sistema elétrico e de outras unidades consum
Nutrition - Opportunities for Startups - Dr. Swaminathan SubramaniamLounge47
This document discusses how nutrition can reshape healthcare management by defining traditional and emerging notions of nutrition. It outlines categories of nutrition like supplements and nutraceuticals. Major chronic diseases like diabetes and obesity are linked to lifestyle and nutrition. Nutrition competes with pharmaceuticals for customers. Emerging science around areas like the microbiome could impact nutrition applications and personalized nutrition using nutrigenomics. Overall, the document suggests nutrition may drive a shift towards prevention and wellness over treatment through lifestyle changes and customized nutrition approaches.
2010 revista anual uoc alumni-castellanoUOC Alumni
El documento describe la comunidad de graduados de la Universidad Abierta de Cataluña (UOC Alumni). Actualmente está formada por más de 22.500 personas graduadas de la UOC de todo el mundo. UOC Alumni ofrece servicios como acceso a materiales docentes, apoyo profesional y descuentos en programas. El objetivo es mantener una red de intercambio entre graduados para compartir conocimientos y oportunidades de forma permanente.
Este documento promueve diversos destinos turísticos en México, incluyendo las playas de Acapulco, la ciudad colonial de Guanajuato y sus momias, las ruinas mayas de Chichen Itza, y la ciudad de Coatepec en Veracruz, proporcionando detalles sobre hoteles, atracciones y paquetes turísticos disponibles en cada lugar a precios que van desde $400 hasta $1500 por persona o familia. También incluye información de contacto para la agencia de viajes Planeta en Puebla.
El arte gótico apareció en Europa en el siglo XII y alcanzó su máximo esplendor en el siglo XIII, desarrollándose principalmente en Francia a través de cuatro estilos. Las catedrales góticas simbolizaban el poder y buscaban tocar el cielo a través de soluciones arquitectónicas innovadoras como pilares, contrafuertes y arbotantes, que permitían distribuir las cargas y eliminar los muros.
Red rock infosolutions Web Development PortfolioVinay Mani
RedRock Info Solutions is a full-service IT firm that offers web design, digital marketing, software development, and IT support services. They have offices in New Delhi and New York and work with clients around the world. Their services include responsive web design, social media promotions, content writing, mobile app development, SEO, and more. Sample projects and client testimonials can be found on their website. They provide both standard and customized website development packages with timelines and payment schedules dependent on the project scope.
Este documento presenta la situación actual de la Corporación Hotelera Nacional (CHN), una organización que ofrece servicios turísticos. CHN desea fortalecer el área de perfiles de clientes y evaluar nuevas oportunidades de negocio. Se propone crear nuevas divisiones de promociones y desarrollo web para mejorar la página, atraer más clientes y tabular datos de usuarios. También se sugiere reorganizar la estructura eliminando los puestos de supervisor de operadores y programadores, y migrando a estos últimos al área
Sondage sur la location chez l'habitant en France Ludovic Clerima
Etude du site Internet Chambrealouer.com commandée à l'IFOP sur l'évolution de la location chez l'habitant en France. Un article à venir sur le sujet sur Explorimmo
Este documento presenta 10 pares de palabras que contienen la letra "ch", como "oso ocho" y "mancha manta". Fue creado por Ma Eugenia Garrido del CEIP Pedro Velarde en Muriedas para ayudar a estudiantes a distinguir palabras con la letra "ch". Los símbolos pictográficos utilizados fueron creados por la Diputación General de Aragón bajo una licencia Creative Commons.
App Value 101: How I Learned to Avoid Bombarding Users with Disruptive Messag...Localytics
Are users being disrupted by your messages? Are you driving users to your app, or driving them away? In this presentation we take a look at some mobile app marketing best practices while examining good and not-so-good examples of app messaging.
Learn how to make your messages move your users!
Este documento habla sobre la importancia de la atención al cliente y la satisfacción total del cliente. Explica que los clientes han cambiado y ahora esperan más confianza, profesionalismo y cortesía. También destaca que para diferenciarse de la competencia, las empresas deben enfocarse en brindar un excelente servicio al cliente a través de un personal capacitado y motivado. Un buen servicio aumenta la lealtad de los clientes y trae mayores ventas e ingresos para la empresa.
This article introduces an oxygen transmission rate test method to test the pudding cup, i.e. the coulometric method. The test principle, instrument features, specifications, and testing procedures are all included in this article, which may provide reference for oxygen permeability test of packaging containers
This article introduces an oxygen transmission rate test method to test the pudding cup, i.e. the coulometric method. The test principle, instrument features, specifications, and testing procedures are all included in this article, which may provide reference for oxygen permeability test of packaging containers
This article introduces an oxygen transmission rate test method to test the pudding cup, i.e. the coulometric method. The test principle, instrument features, specifications, and testing procedures are all included in this article, which may provide reference for oxygen permeability test of packaging containers.
This document shows a 90 degree adhesive peel strength test on a Labthink XLW (PC) Auto Tensile Tester. We fit the XLW(PC) with our 90 degree peel strength fixture and one vise grip on the bottom crosshead to hold the free end of the tape. The fixture has numerous tapped holes that allow you to clamp a multitude of various parts and substrates to the test bed. This test measures the maximum load and also the average load of adhesive tape bonded to a Polystyrene foam substrate.
The i-Thermotek 2500 Hot Tack Tester can determine the hot tack and heat seal performance of plastic films, composite films, and other packaging materials. It can also test the peel strength and tensile properties of adhesives, tapes, and other flexible materials. The tester prepares specimens according to standards, mounts them in grips, sets test parameters, and records data from tests that measure properties like peel strength and tensile strength.
The i-Thermotek 2500 Hot Tack Tester can determine the hot tack and heat seal performance of plastic films, composite films, and other packaging materials. It can also test the peel strength and tensile properties of adhesives, tapes, and other flexible materials. The tester prepares specimens according to standards, mounts them in grips, sets test parameters, and records data from tests that measure properties like peel strength and tensile strength.
i-Leaktek 6600 Leak and Seal Strength Tester is designed for determination of seal strength and seal performance test of various heat sealed flexible package and sterilized package, seal performance test of pilfer-proof closures, quantitative testing of leak characteristics, compression resistance, capsule disengaging strength, cap body joint strength, seal-edge seal strength and butting strength of flexible tubes, and testing of anti-compression, seal performance and burst resistance of the bottles.
The i-Leaktek 6600 Leak and Seal Strength Tester is designed to test the seal strength and performance of various flexible packages and sterilized packages. It can test leak characteristics, compression resistance, and burst resistance of bottles. The tester requires warming up for 30 minutes before mounting at least 5 specimen samples free of defects. Test parameters are then set and the test is run, with the results curve and report viewed afterwards.
i-Meditek 1300 Medical Packaging Tester is designed to determine the puncture force of medical rubber closure, pullout force of rubber closure, break force of ampoule, sliding resistance of syringe, puncture force of syringe needle, connection force of syringe needle and needle hub, connection force of syringe needle hub and shield, seal performance of plastic blood bag, and the performance of other medical appliances.
The PARAM® XLW (G6) Auto Tensile Tester is a professional instrument that can perform a variety of tensile tests including tensile strength, deformation, peeling and tearing. It has 6 working stations, 1200mm extra-long stroke, and precision load cells that ensure accurate test results. The instrument is controlled via computer software which supports statistical analysis and management of test data. It is used to test properties of over 1000 materials including packaging, textiles, adhesive tapes and more.
The PARAM FT-F1 Fogging Tester is used to evaluate the fogging characteristics of volatile constituents in plastics, textiles, and other materials used in vehicles and aircraft under high temperature conditions. It has 6 test stations that can simultaneously test samples and controls. Test methods include heating samples and measuring changes in gloss, fogging, or condensed material weight on a cooled plate. The instrument conforms to international standards and is suited to testing fogging in vehicle interior parts, plastics, carpets, leather, insulation materials, and adhesive products.
XYD-15K Box Compression Tester can be used to measure the compressive resistance, deformation and stacking capability of cartons, beehive crates, plastic tanks (for edible oil and mineral water), paper tanks, paper cases, IBC tanks and other packages.
XYD-15K Box Compression Tester can be used to measure the compressive resistance, deformation and stacking capability of cartons, beehive crates, plastic tanks (for edible oil and mineral water), paper tanks, paper cases, IBC tanks and other packages.
This instrument is based on the humidity sensor method, and is professionally applicable to the water vapor transmission rate test of film specimens. It is equipped with three individual test dishes, and the testing process is completely automatic and conforms to international standards.
This instrument is based on the cup method, and is professionally applicable to the water vapor transmission rate test of film specimens. It is equipped with three individual test dishes and the testing process is completely automatic and conforms to international standards.
VAC-VBS is based on the differential pressure method, and is professionally applicable to the determination of gas transmission rate of films, sheeting, high barrier materials, and aluminum foils.
VAC-V1 is based on the differential pressure method, and is professionally applicable to the determination of gas transmission rate as well as solubility coefficient, diffusion coefficient and permeability coefficient of plastic films, composite films, high barrier materials, sheeting, metal foils, rubber, tires, and permeable membranes.
This instrument is professionally applicable to the determination of water vapor transmission rate of plastic films, composite films, high barrier materials, back-sheets, sheeting, aluminum foils, waterproof materials, and other materials used in sanitary and medical industry. By testing the water vapor transmission rate, the technical indexes of materials could be controlled to meet the requirements for production.
TQD-G1 is professionally applicable to the determination of air permeability of decorating materials used in cars, e.g. polyurethane, expanded plastics, PVC, leather, textiles, non-woven and other materials. Through the test, physical characteristics of the materials could be controlled to meet practical application requirements of products.
SLY-S1 Tearing Tester is designed for the tearing test of films, sheets, flexible PVC, PVDC, waterproof films, woven materials, polypropylene, polyester, paper, cardboard, textile and non-woven and etc.
1. PARAM® XLW (PC) Auto Tensile Tester
Yarina Gao trade5@labthink.cn
Professional
XLW (PC) Auto Tensile Tester is professionally applicable to the
determination of force properties of various flexible packaging materials,
with high precision (better than 0.5% of reading accuracy) and multiple
test ranges. The instrument is designed with 7independent test modes and
could perform tests at seven different test speeds to meet various test
conditions. Intelligent software facilitates to operate the instrument and
provides data analysis and comparison functions.
Better than 0.5% of reading value effectively ensures accurate test results
7independent test modes are available, including tensile strength, peeling force, tearing force and other force
properties of flexible packages
1000mm extra-long stroke satisfies the test needs of various materials with extreme deformation rate
Different test range of load cells and 7distinct test speeds to meet different test requirements
The instrument is controlled by micro-computer with menu interface, PVC operation panel and large LCD
display
Intelligent designs of over-travel protection, overload protect, automatic position reset and power failure
memory for safe test operation
Professional operating software support statistical analysis of group specimens, superposition analysis of test
curves and historical data comparison functions
Support Lystem™ Lab Data Sharing System for uniform and systematic data management
Applications
This instrument is equipped with more than 100 grips for tests of more than 1000 materials. And customization is
also available for special material tests. Examples of instrument applications:
Basic
Extended Applications
Applications
Puncture Test of Puncture/Pullout
Puncture Test of Puncture Test of
Tensile Property Hypodermic Needles Test of Flexible
Films Infusion Bags
in Artificial Skin Rubber Closures
Test of Tensile Opening Resistance Puncture/Pullout
Tear Test of ZD -Type Opening Force Test
Strength and Test of Combined Test of Oral Liquid
Caps of Oral Liquid Caps
Elongation Rate Covers Caps
90 Degree Pullout Puncture/Pullout
Test of Tensile Pullout Test of 23 Degree Pullout
Test of Infusion Bag Test of Bottle Caps
Strength at Break Infusion Bag Caps Test of Bottle Caps
Caps or Rubber Closures
Tear Resistance Test 90 Degree Peel Test
Tear Resistance 90 Degree Peel Test Tear Resistance Test
of Adhesive Binding of Water-soluble
Test of Adhesive Tapes of Adhesives
Books Plasters
Heatseal Strength Adhesive Strength Adhesive Strength Peel Test of Flexible Removal Force of
Test Test (soft) Test (hard) Tube Caps Pipes and Pipe Joints
Labthink Instruments Co., Ltd.144 Wuyingshan Road, Jinan, P.R.China (250031) Phone: +86 -531-85068566 FAX: +86-531-85812140
w w w.labthinkinter n atio n al.co m.cn
2. Opening Force Test
90 Degree Peel Pullout Test of Pullout Test of Tooth Tensile Strength of
of Jelly Cups and
Test Cosmetic Brush Hair Brush Hair Ropes at Break
Yogurt Cups
45 Degree Peel Test
180 Degree Peel Peel Test of Cup Pullout Test of Tensile Strength of
of Bottle
Test Films Rubber Stoppers Sealing Bags
Membranes
Peel Test of Magnetic 90 Degree Peel Test Tear Resistance of Separating Force of
Cores of Magnetic Cards Heat Sealing Films Protect Films
Compressive
Peel Test of Release Tear Test Using Unwrapping Force
Resistance of Plastic
Paper Trouser Method of Adhesive Tapes
Bottles
135 Degree Peel Peeling Grips of
20 Degree Peel Test Eccentric Grips
Test of Plugs Floating Rollers
Japanese Sample
Wide Sample Grips British Sample Grips
Grips
Test Principle
The pre-conditioned specimen is mounted between two grips, which move in relative direction during the test.
The signals of force and displacement changes are separately recorded by the load cell fixed on the driven grip
and embedded displacement transducer. The tensile strength, tear strength and elongation rate can be obtained by
further calculation.
This test instrument conforms to many national and international standards:
ISO 37, GB 8808, GB/T 1040.1-2006, GB/T 1040.2-2006, GB/T 1040.3-2006, GB/T 1040.4-2006, GB/T
1040.5-2008, GB/T4850-2002, GB/T12914-2008, GB/T 17200, GB/T 16578.1-2008, GB/T 7122, GB/T 2790,
GB/T 2791, GB/T 2792, ASTM E4, ASTM D882, ASTM D1938, ASTM D3330, ASTM F88, ASTM F904, JIS
P8113, QB/T 2358, QB/T 1130
Technical Specifications
Items Specifications
Test Range 500N, 50N (one of them is available)
Accuracy <0.5% of reading value
Number of Specimens 1
Test Speed 50, 100, 150, 200, 250, 300, 500 mm/min
30 mm (Standard Grip)
Specimen Width
50 mm (Optional Grip)
Stroke 1000 mm
Instrument Size 450mm(L) x 450mm(W) x 1410mm(H)
Power Supply AC 220V 50 Hz
Net Weight 68 kg
Labthink Instruments Co., Ltd.144 Wuyingshan Road, Jinan, P.R.China (250031) Phone: +86 -531-85068566 FAX: +86-531-85812140
w w w.labthinkinter n atio n al.co m.cn
3. Configurations
Standard
Mainbody, Universal Grips, Professional Software, and Communication Cable
Configurations
Optional Parts Standard Pressure Roller, Test Plate, Sample Cutter, and Customized Grips
Labthink Instruments Co., Ltd.144 Wuyingshan Road, Jinan, P.R.China (250031) Phone: +86 -531-85068566 FAX: +86-531-85812140
w w w.labthinkinter n atio n al.co m.cn