Radio wave signals do not travel in a straight line path. There may be some obstacles between the source and the destination which cause diffraction, reflection, scattering and attenuation. There are some types of obstacles such as knife edge, wedges and round edges. This paper shows the diffraction loss caused by wedges based on Uniformal Theory of Diffraction (UTD) given in (ITU-R Recommendation P.526-12) using Matlab software. It could be said that this is an important method because radio waves travel over wedge shaped roofs of buildings and corners of the buildings. In addition this diffraction loss changes for both roofs and corners for a particular obstruction material. Furthermore, the electrical properties of the wedge shaped obstacles are affecting the diffraction loss such as conductivity and dielectric constant. The result shows that higher conductivity leads to have a higher amplitude oscillation at the receiver.
The propagation properties of electromagnetic waves in the application of thr...TBSS Group
"Through-wall radar sensors are sensors which allow the user to "see" through walls. By sending microwave signals from a directional transmitter (also known as horn transmitter), through a wall, reflecting it against the subject and back, the radar would be able to determine whether if there is a person behind the wall and how far away he is.
Commercial applications for such through-wall radars would help police and military force greatly, allowing them to "see" their enemies before they are seen in the field.
A detailed study on the properties of the electromagnetic wave propagation through a building wall is conducted to determine the important parameters that affect the performance capability of through-wall radar. Measurements are carried out to verify the results obtained from the field."
Propagation Model for Tree Blockage in Mobile Communication Systems using Uni...IJEEE
A deterministic model for spherical wave propagation in microcellular urban environment is presented. This methodis based on ray tracing and uniform theory of diffraction. The various ray contributions includes the diffraction from corner of obstacle, reflection from ground and direct wave. According to the height of transmitting station, different ray paths will be presented in the received signal. Calculation is carried out using hard and soft polarization. Results can be used for the planning of new cellular system.
The propagation properties of electromagnetic waves in the application of thr...TBSS Group
"Through-wall radar sensors are sensors which allow the user to "see" through walls. By sending microwave signals from a directional transmitter (also known as horn transmitter), through a wall, reflecting it against the subject and back, the radar would be able to determine whether if there is a person behind the wall and how far away he is.
Commercial applications for such through-wall radars would help police and military force greatly, allowing them to "see" their enemies before they are seen in the field.
A detailed study on the properties of the electromagnetic wave propagation through a building wall is conducted to determine the important parameters that affect the performance capability of through-wall radar. Measurements are carried out to verify the results obtained from the field."
Propagation Model for Tree Blockage in Mobile Communication Systems using Uni...IJEEE
A deterministic model for spherical wave propagation in microcellular urban environment is presented. This methodis based on ray tracing and uniform theory of diffraction. The various ray contributions includes the diffraction from corner of obstacle, reflection from ground and direct wave. According to the height of transmitting station, different ray paths will be presented in the received signal. Calculation is carried out using hard and soft polarization. Results can be used for the planning of new cellular system.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
Average symbol error rate analysis of reconfigurable intelligent surfaces-as...IJECEIAES
Optical wireless communication (OWC) has attracted significant interest recently in academia and industry. Free-space optical (FSO) communication systems are where free space acts as a communication channel between transceivers that are line of sight (LOS) for the successful transmission of optical signals. The FSO transmissions through the atmosphere, nevertheless, bring significant challenges, besides the uncertainty of atmospheric channels, especially the signal fading due to the atmospheric turbulence, attenuation and pointing errors caused by the random beam misalignments between transceivers, signal obstruction due to buildings or trees can pre-vent the transmitted message to reach the destination. This study theoretically investigates the average symbol error rate (ASER) of reconfigurable intelligent surfaces (RIS) assisted FSO link over log-normal turbulence channels. The RIS effect is examined by considering the influence of link distance, transmitted optical power, and quadrature amplitude modulation (QAM) scheme on the ASER.
Possible media for communication
Introduction to Communication Media
Introduction to Microwave communication
Manufacturers of Microwave
Why Microwave?
Characteristics of microwave
Types of Microwave communication
Types of Microwave Links
Requirements for the microwave communication
What is LOS?
Wave Propagation in the atmosphere
Multi path Propagation
LOS Purpose & requirements
Limitations of Line of Sight Systems
Design of Line of Sight Microwave Links
K- factor
Variations of the ray curvature as a function of k
Fresnel zone
Obstacles & Loses
Knife Edge Obstacles
Smooth Spherical Earth Obstacles
Path Loss
Other losses
Why vertical polarization favorable at high freq
Antenna type & Gain
RECEIVER SENSITIVITY, FADE MARGIN AND SIGNAL TO NOISE RATIO
Fading Margin
Reliability
Microwaves are a type of electromagnetic radiation, similar to radio waves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays. They are named "microwaves" because they are smaller than the waves used in traditional radio broadcasting, typically ranging in length from about one millimeter to one meter.
This paper presents a thorough study of the behaviour of microwave absorption occurring in lossy
dielectric slabs as used for microwave absorbers. The influence of the various parameters governing
absorption is demonstrated : dielectric constant, conductivity, thickness of slab and frequency. It is
shown that for several combinations of values for these parameters absorption can be maximized to up
to unity, i.e. all the incident power is absorbed.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
More Related Content
Similar to THE EFFECTS OF CONDUCTIVITY OF THE MATERIALS ASSOCIATED WITH THE WEDGES ON THE LOSS BY DIFFRACTION
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
Theoretical work submitted to the Journal should be original in its motivation or modeling structure. Empirical analysis should be based on a theoretical framework and should be capable of replication. It is expected that all materials required for replication (including computer programs and data sets) should be available upon request to the authors.
Average symbol error rate analysis of reconfigurable intelligent surfaces-as...IJECEIAES
Optical wireless communication (OWC) has attracted significant interest recently in academia and industry. Free-space optical (FSO) communication systems are where free space acts as a communication channel between transceivers that are line of sight (LOS) for the successful transmission of optical signals. The FSO transmissions through the atmosphere, nevertheless, bring significant challenges, besides the uncertainty of atmospheric channels, especially the signal fading due to the atmospheric turbulence, attenuation and pointing errors caused by the random beam misalignments between transceivers, signal obstruction due to buildings or trees can pre-vent the transmitted message to reach the destination. This study theoretically investigates the average symbol error rate (ASER) of reconfigurable intelligent surfaces (RIS) assisted FSO link over log-normal turbulence channels. The RIS effect is examined by considering the influence of link distance, transmitted optical power, and quadrature amplitude modulation (QAM) scheme on the ASER.
Possible media for communication
Introduction to Communication Media
Introduction to Microwave communication
Manufacturers of Microwave
Why Microwave?
Characteristics of microwave
Types of Microwave communication
Types of Microwave Links
Requirements for the microwave communication
What is LOS?
Wave Propagation in the atmosphere
Multi path Propagation
LOS Purpose & requirements
Limitations of Line of Sight Systems
Design of Line of Sight Microwave Links
K- factor
Variations of the ray curvature as a function of k
Fresnel zone
Obstacles & Loses
Knife Edge Obstacles
Smooth Spherical Earth Obstacles
Path Loss
Other losses
Why vertical polarization favorable at high freq
Antenna type & Gain
RECEIVER SENSITIVITY, FADE MARGIN AND SIGNAL TO NOISE RATIO
Fading Margin
Reliability
Microwaves are a type of electromagnetic radiation, similar to radio waves, infrared radiation, visible light, ultraviolet radiation, X-rays, and gamma rays. They are named "microwaves" because they are smaller than the waves used in traditional radio broadcasting, typically ranging in length from about one millimeter to one meter.
This paper presents a thorough study of the behaviour of microwave absorption occurring in lossy
dielectric slabs as used for microwave absorbers. The influence of the various parameters governing
absorption is demonstrated : dielectric constant, conductivity, thickness of slab and frequency. It is
shown that for several combinations of values for these parameters absorption can be maximized to up
to unity, i.e. all the incident power is absorbed.
Similar to THE EFFECTS OF CONDUCTIVITY OF THE MATERIALS ASSOCIATED WITH THE WEDGES ON THE LOSS BY DIFFRACTION (19)
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)
THE EFFECTS OF CONDUCTIVITY OF THE MATERIALS ASSOCIATED WITH THE WEDGES ON THE LOSS BY DIFFRACTION
1. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
DOI: 10.5121/jant.2015.1101 1
THE EFFECTS OF CONDUCTIVITY OF THE MATERIALS
ASSOCIATED WITH THE WEDGES ON THE LOSS BY
DIFFRACTION
Bawar Abdalla1
1
Department of Software Engineering, Koya University, Koya, Iraq
ABSTRACT
Radio wave signals do not travel in a straight line path. There may be some obstacles between the source
and the destination which cause diffraction, reflection, scattering and attenuation. There are some types of
obstacles such as knife edge, wedges and round edges. This paper shows the diffraction loss caused by
wedges based on Uniformal Theory of Diffraction (UTD) given in (ITU-R Recommendation P.526-12)
using Matlab software. It could be said that this is an important method because radio waves travel over
wedge shaped roofs of buildings and corners of the buildings. In addition this diffraction loss changes for
both roofs and corners for a particular obstruction material. Furthermore, the electrical properties of the
wedge shaped obstacles are affecting the diffraction loss such as conductivity and dielectric constant. The
result shows that higher conductivity leads to have a higher amplitude oscillation at the receiver.
KEYWORDS
Radio wave propagation, diffraction, wedge diffraction
1. INTRODUCTION
1.1 BACKGROUND
Nowadays, communication technology has developed rapidly as compared to the past. Radio
waves are electromagnetic waves which travel from a transmitting point to a receiving point. The
length of the path between the transmitter and the receiver is different for each type of
propagation, such as mobile or satellite communication. In mobile communication, when the
signal travels from the transmitter to the receiver, ‘it does not simply travel in a straight line’
(Barclay, 2003 p.129). There may be some obstacles and physical terrain that can cause
reflection, scattering and diffraction of the signal, with the addition of a direct signal which may
cause multipath signals at the receiving point. In addition, these different signals may cause
interference when they are out of phase which can decrease the strength of the signal at the
receiver [1].
Basically, Diffraction is based on Huygens’ Principle which says in radio wave propagation every
point of the wave acts a source for the next point [2]. For example, when signals are obstructed by
an edge they act as a new source to the receiver from the edge as shown in Figure (1). Diffraction
occurs when the radio waves strike the edge of an obstacle which is situated between the
transmitter and the receiver. ‘The apparent bending of radio waves around the edge of an
obstruction is known as diffraction’ (Parsons, 2000 p.34). However, the received signal does not
decrease to the lowest strength directly after the obstacle. It can be said that this is one of the most
important phenomena in terms of propagation, because there are a range of types of obstacles
such as knife-edge, round, random and wedges. However, the rate of loss due to diffraction varies
for each type of obstacle.
2. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
2
Figure 1. Huygens’ construction [1]
As can be seen from Figure (1) the Advancing Wavefront comes from the original source and at
each point of line A produces a new source to line B in the direction of propagation.
1.2 KNIFE-EDGE DIFFRACTION:
This type of diffraction is the result of radio waves striking an obstacle with a thin or sharp edge
[1]. The geometry of knife edge diffraction is shown in Figure (2) and Figure (3)
d1 h d2
Tx Rx
Figure 2. Geometry of knife edge diffraction height > 0 [1]
Tx Rx
d1 h d2
Figure 3. Geometry of knife edge diffraction height < 0 [1]
d1: distance from transmitter to the edge.
d2: distance from the edge to the receiver.
h: height of the obstacle
As can be seen from Figures (2) and (3), the signal travels from the transmitter and is diffracted
by the edge of the obstacle. In Figure (2), the height of the obstacle is positive because it is above
the line of sight. On the other hand, in Figure (3), the height is negative because the edge is below
the line of sight. To calculate the loss associated with this type of diffraction, a single
3. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
3
dimensionless parameter - ν - can be used because the other parameters can be combined with it
as in [3]. Moreover, the formula for calculating the ν parameter in this case is:
[3] (1)
Furthermore, the diffraction loss J (ν) can be calculated as follows:
J (ν) = 6.9 + 20 log + ν 0.1] (dB) [3] (2)
Moreover, (ITU-R Recommendation) has provided a Matlab function to calculate this loss in
(ITU-R Recommendation p.525-12). Figure (4) shows the diffraction loss versus the ν parameter.
Figure 4. Knife edge diffraction loss [3]
Figure (4) shows how the loss varies according to the v parameter in knife edge diffraction.
However, it can be assumed that for a value of ν below -0.7, the loss is zero dB [3]. For values of
ν greater than -0.7 the received signal strength decrease gradually such as at ν is equal to 3 the
loss is nearly 22 dB. This means, the received amplitude of the signal has decreased.
1.3 DIFFRACTION OVER WEDGES:
Furthermore, it is more interesting to investigate the effects on diffraction loss of the other types
of edge associated with obstacles such as curved edges or wedges since these are more complex
to deal with. Wedge diffraction was based on the Geometrical Theory of Diffraction (GTD)
which was published by Keller in 1962 [5]. After that Kouyoumjian Pathak extended this GTD to
UTD [6]. Moreover, for a giving incident angle, the receiving point may receive more than the
diffracted signal, depending on its position. For example it may receive a signal reflected by the
wedge and the direct signal (Line of Sight). To investigate how many signals the receiver
receives, two boundaries can be defined. One of them is the shadow boundary which below this
the direct signal and the reflected signal are not available. The other boundary is the reflection
boundary which below this the reflected signal is not available [1]. These boundaries are
illustrated in Figures (5, 6, and 7)
4. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
4
Figure 5. When the receiving point is above the boundaries. [1]
As can be seen from the above figure, the receiver locates above both boundaries. In this case the
receiver receives the direct signal, a reflected signal and a diffracted signal due to the edge of the
wedge.
Figure 6. When the receiving point is between the two boundaries [1]
As can be seen from the above figure, the receiver is located above the shadow and below the
reflection boundary. This leads to the absence of a reflected signal, and the receiver receives only
the direct and the diffracted signal.
The last case is when the receiver’s position is below the shadow boundary. In this case, both the
reflected and the direct signal will be absent, and the receiver receives only the diffracted signal
as shown in Figure (7).
5. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
5
Figure 7. When the receiving point is below two boundaries [1]
Measuring diffraction loss due to wedges is important because in western or rainy countries such
as the UK, most of the roofs of the buildings are wedge shaped. In addition, signals travel around
the corners of the buildings and these corners are considered as a wedge in terms of parallel
polarization unlike roofs which are considered in terms of perpendicular polarization and these
corners are causing diffraction. In addition, the material which makes up the wedge or the corner
affects the rate of the diffraction loss. For this reason the dielectric constant and conductivity of
the wedge material are taken into account [3]. The aim of this paper is to implement a Matlab
code to investigate and validate diffraction loss caused by a finitely conducting wedge for both
perpendicular and parallel polarization based on (ITU-R Recommendation p.526-12) as well as to
show how this loss varies according to the material used to make the wedge. Finally, it compares
the relationship between knife edge diffraction and UTD by showing how UTD can be used to
obtain a knife edge diffraction result as well as it investigates and compares the rate of varying
diffraction loss for both knife edge and wedge versus ν parameter.
2. METHODOLOGY
In this case of study, Diffraction by a single rectangular aperture (wedge) has been implemented
by using Matlab software based on ITU document (ITU-R P.526 - 12).This method is originally
based on Uniformal Theory of Diffraction (UTD) which made of some mathematical formulas
and calculations. Additionally, the reflection from the wedge and the Line of Sight signals are
considered. The geometry of wedge diffraction can be seen in the Figure (8).
6. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
6
Figure 8. Geometry of UTD [3]
As can be seen from the above figure, there are some parameters and they have effects on the
electric field at the Receiver. The wedge has two faces, 0 face and n face. The angles are
measured from the 0 face.
The received field by the diffraction can be calculated by using the below equation.
. [3] (3)
Where:
: electric field at the receiver.
e0: source amplitude
s1: distance from the transmitter to the edge of the wedge.
s2: distance from the edge of the wedge to the receiver.
k: wave number which equals to 2π/λ.
The external angle of the wedge is nπ. However the internal angle of the wedge is
2π−nπ.
is Diffraction coefficient for both parallel incident on the edge of the wedge or
perpendicular. This coefficient can be calculated using the following formula.
[3] (4)
: incident angle.
7. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
7
: angle of diffraction.
n: external wedge angle as a multiple of radian
The formula of the diffraction parameter includes Fresnel integral which is:
[3] (5)
Where =kL ( ).
[3] (6)
( ) = 2 cos2 [3] (7)
[3] (8)
are Integers which nearly satisfy the equation.
There are two different ways to calculate this integral. One of them is using normal calculation.
Another one is using an alternative way which is based on Boersma’s approximation [4]. Both of
them lead to the same result. However, for this case of study the Boersma’s approximation has
been used.
Furthermore, it includes reflection coefficient (R) from the wedge for parallel or perpendicular
incident which depends on the conductivity and dielectric constant of the wedge material. It can
be said that this coefficient is two parts for each case of polarization which are R0 and Rn for 0
and n faces [3].
Reflection Coefficient for parallel incident is:
R||= [3] (9)
Reflection Coefficient for perpendicular incident is:
R⊥= [3] (10)
Where,
= for R0
= (nπ− ) for Rn
η=εr – j * 18 * 109
* [3] (11)
εr : Relative dielectric constant of the material of the wedge.
σ : Material conductivity.
: Frequency of the radio wave
In addition, the reflection angle should be found. This can be done using Cartesian axes. First of
all, we found the position of the transmitter and the receiver at the coordinate then the reflection
angle can be found. However, the both distances by the reflected and line of sight rays should be
found in order to calculate the loss happened due to them using the following equation.
8. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
8
[3] (12)
Where s is the distance by the reflected ray or the Line Of Sight. However, for calculating loss
caused by reflection, the nominator should be multiplied by the reflection angle.
Then, the boundaries should be defined. To do this, we need to divide the area into three separate
parts. One of them is the above reflection boundary area where the receiver receives the whole
three rays. Another boundary is between shadow boundary and the reflection boundary where the
receiver receives only direct and diffracted signal. The last one is the below shadow boundary
where only the diffracted signal is being receiving.
To find the reflection boundary this equation should be used.
Reflection boundary (Degree) = 180 - (13)
So for smaller than reflection boundary means the receiver locates above the reflection
boundary so it receives a combination of the three rays.
To find the shadow boundary this equation should be used.
Shadow boundary (Degree) = 180 + (14)
So for greater or equal than the reflection boundary and smaller than the shadow boundary
means the receiver locates between the boundaries so it receives a combination of diffracted and
direct rays.
Finally, for greater than shadow boundary means the receiver locates below the shadow
boundary so it receives only the diffracted ray.
For this case of study, the transmitter is located in a place with incident angle of 45O
and the
receiving point is moving from the transmitter to behind the wedge from angle of diffraction of
90O
to 240 O
in order to investigate the effects of all positions (above, between and below the
boundaries) on the diffraction. In addition, the frequency of 1800 MHz has been used to
investigate the GSM propagation. Also the distances from the transmitter to the wedge and from
the wedge to the receiver is assigned to 15 meter for a perfectly conducting wedge which means
the conductivity is the highest. Thus the R parameters in equations (9) and (10) will be -1.
Moreover, different types of materials are investigated in order to observe how loss changes
according to the type of the material of the wedge such as wood, brick.
3. Results and Discussion:
In this part of the Work several outputs have been observed to predict different effects of
individual material and parameters on the diffraction loss.
Firstly, we observed a perpendicular polarization which means diffraction by the ridge of a wedge
shaped roof as shown in figure (9). The wedge is considered as a finitely conducting wedge. This
means, the conductivity of the wedge material is highest and this makes both R0 and Rn in
equation (10) equal to -1. In addition the frequency of GSM has been used which is 1800 MHz.
Also, the other parameters are:
The internal angle of the wedge = 90 degree.
s1 = 15 meter.
s2 = 15 meter.
9. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
9
Figure 9. Diffraction over a finitely conducting wedge
As can be seen from the above figure, when the receiver locates in an angle lower than the
reflection boundary the rate of changing amplitude of the received signal is very fast. This is also
called fast fading or complicated lobing because at these areas the receiver receives a
combination of three different signals which are direct, reflected and diffracted rays [1]. When the
receiver moves away from the reflection boundary which is angle 135o
the lobing will be less
complicated and the oscillation of the amplitude of the received signal reduces to a lower
oscillation this is because the receiver receives a combination of two rays which are direct and
diffracted rays. However, when the receiver moves away from the shadow boundary which is
angle 225o
it will receive only diffracted ray and this is result in preventing fading. In addition, As
far as the receiver moves away the signal amplitude will be lower because it goes to those areas
which are more shadowed such as in angle 240o
the amplitude is less than -20 dB.
It is also interesting to investigate diffraction loss caused by a finitely conducting corner of a
building. To do this, the polarization of the method is changed to parallel polarization. Figure (10)
shows diffraction loss over proper 90o
corners of building in GSM system when:
s1 = 15 meter,
s2 = 15 meter
Figure 10. Diffraction over a finitely conducting corner of a building
10. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
10
Similarly, the above result is the same as the one in Figure (9) because in both cases it is assumed
that the wedge and the corner are perfectly conducting. This makes the both equations (9) and
(10) to be equal to -1 and the results will be the same.
However, it is also interesting to investigate different type of materials of the wedges or the
corners. Figure (11) shows result of diffraction over a wedge which made of wood. It is assumed
that the dielectric constant of wood is equal to 10 and the highest situation of conductivity
is .
Figure 11. Diffraction over a wedge made of wood
As can be seen from the above figure, the fading and lobing of the received signal is nearly the
same as a perfectly conducting wedge. However, the oscillation of the amplitude tends to
decrease. For example, at the angle of 90o
the minimum amplitude is nearly -3 dB while for a
finitely conducting wedge is nearly -5 dB. In this case, at the angle of nearly 130o
the lowest
amplitude is nearly -5 dB. However, for a perfectly conducting wedge is nearly -12 dB. It can be
said that the lower conductivity of the obstruction materials leads to have lower amplitude
oscillation of the received signal at the receiver.
In order to investigate more material effects on the diffraction loss, different types of materials
can be used. For example, some wedges are made of ceramics and the dielectric constant of
ceramic is assumed to be nearly 6 and the conductivity varies according to the type of the ceramic
made up the wedge [7]. In this case it is assumed to .
Figure (12) shows diffraction over a ceramic wedge. Where:
The internal angle of the wedge = 90 degree.
s1 = 15 meter.
s2 = 15 meter.
11. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
11
Figure 12. Diffraction over a wedge made of ceramic
As described before, lower conductivity tends to lower amplitude oscillation of the signal at the
receiver. In comparison, for above figure which the wedge made of ceramic the amplitude
oscillation is lower than the one in Figure (11) which was the output of diffraction by a wooden
wedge because the conductivity of ceramic is lower than the conductivity of wood. This
fluctuation of amplitude can be noted in angle of 130o
while in the wooden wedge the amplitude
is lower than -5 dB. However for the ceramic wedge is greater than -5 dB.
Furthermore, diffraction by the corners of buildings also occurs, the material makes up the
buildings is often brick. This brick originally may be made of ceramics. Figure (13) shows
diffraction loss caused by a ceramic corner. It is known that the angle of the corners is mostly 90o
.
s1 = 15 meter.
s2 = 15 meter.
Figure 13. Diffraction by a corner which is made of ceramic.
12. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
12
As can be seen from the above figure, the pick amplitude is much lower than the perfectly
conducting corner in figure (10) because the conductivity here is low and lower conductivity
results in lower amplitude. As compared to the diffraction by a wedge which made of ceramic in
figure (12), here the amplitude of the received signal at 90o
and 100o
is nearly 0 dB. However, for
perpendicular incident is between 2 and -2 dB. In addition, the amplitude oscillation between
angles 145o
and 170o
is very low and fading tends to be unavailable.
Some values of the relative dB to the free space have been exported from the Matlab results to
compare the amplitude oscillation for both perpendicular and parallel incident from diffraction
angel of 90o
to 220o
for a wedge shaped obstacle made of ceramic. These values can be seen from
Table (1).
Table 1. Received signal strength for a wedge made of Ceramic in both parallel and perpendicular
polarization.
Angle (Degree) Perpendicular (dB) Parallel (dB)
90 2.026 - 0.0222
95 - 2.6348 0.1145
100 2.3506 - 0.4842
105 - 1.7146 0.3367
110 - 3.6803 0.8564
115 - 3.5502 0.8363
120 - 2.4803 1.0379
125 2.1043 - 0.7784
130 - 0.5952 0.8552
140 0.6533 - 0.1759
145 - 0.0778 0.0408
150 0.2083 - 0.035
155 0.1824 - 0.0139
160 0.1505 0.0023
165 - 0.0151 - 0.0022
170 0.3368 0.0618
180 - 0.1663 - 0.0565
185 - 0.4032 - 0.1623
190 0.4074 0.1981
195 0.0383 0.0183
200 0.4306 0.2697
205 - 0.4228 - 0.2959
210 0.4614 0.3511
215 - 0.2646 - 0.2149
220 0.2985 0.3144
As can be seen from above table, the amplitude of the received signal varies for each diffraction
angle. It can be observed that from the above data the maximum amplitude is 2.356 dB and
minimum is - 3.6803 dB for perpendicular polarization at angles 100o
and 115o
respectively.
However this oscillation decreases to between 1.0379 dB and - 0.7784 dB for parallel polarization
at angles 120 o
and 125o
respectively. Moreover, the resolution of the angles is 5 degree if we take
a smaller resolution we may obtain a greater oscillation of the amplitude at the other angles.
It can be said that the buildings have windows and sometimes these windows locate at the corner
of the buildings. Clearly, these corner-shaped windows cause diffraction loss. However, the
13. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
13
conductivity and dielectric constant of the window material are taken into account. Mostly,
windows are made of glasses and the conductivity of glass is assumed to be and the
dielectric constant is nearly 4.6. Figure (14) shows diffraction loss caused by windows of
buildings.
Figure 14. Diffraction by a corner which is made of Glass.
As can be seen from the above figure, due to the low conductivity of the material which makes
the corner up the amplitude oscillation is very low at a rate in some positions of the receiver the
received signal amplitude is 0 dB such as from 150o
to nearly 163o
. However, at those places
where only the diffracted angle is available the received signal is the same as finitely conducting
corners such as above 225o
which means below the shadow boundary.
According to (Barclay, 2003) and (ITU-R Recommendation P.526-12) the result of knife edge
diffraction can be obtained using wedge diffraction methods. To do this, the reflection coefficient
should be assigned to 0 as well as the value of n should be equal to 2 in order to make the internal
angle of the wedge to 0o. The result in this case should be the same as the one given in Figure (4).
Figure (15) shows the result of knife edge diffraction using wedge diffraction implementation.
14. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
14
Figure 15. Knife edge diffraction loss.
In comparison, the results are the same. It can be said that, in the knife edge model
implementation, the amplitude of the received signal for ν smaller than -0.7 is assigned to 0 [3].
This is an approximate value. However, in the knife edge model the loss is plotted versus v
parameter while in wedge diffraction it is versus the diffraction angle. It is clear that the ν
parameter depends on the height of the obstacle and the Diffraction angle indicates the place of
the receiver. Thus, the height of the obstacle can be found through the diffraction angle then ν
parameter can be found using equation (1).
4. CONCLUSION
In conclusion, this paper has investigated loss caused by diffraction over the roofs and corners of
the buildings which are wedge shaped. The method was to implement wedge diffraction based on
UTD with two dimensions propagations which means the sender, receiver and the edge are in a
straight line given in the (ITU-R Recommendation P.512-12). The importance of this paper is that
the method takes the reflected and direct signals into account with respect of the diffracted ray. In
addition, this method considers the electrical properties of the materials which made up the
wedges such as conductivity and dielectric constant as well as it takes the polarization into
account. Moreover, this model is pretty flexible in terms of widely using such as obtaining knife
edge result. Several results were achieved for both parallel and perpendicular incident as well as
for different materials. In addition, the results show that higher conductivity of the materials tends
to have higher amplitude oscillation at the receiving point. As well as, diffraction loss caused by
corners of buildings is more than that loss caused by the wedges for particular material. Unlike
knife edge diffraction, this method considers the reflection from the edges. It can be suggested
that in the future this model can be improved to investigate diffraction loss in three dimensions or
diffraction by more than one wedge between the transmitter and the receiver as well as to
estimate the other shapes of the obstacles such as round or random edges.
REFERENCES:
[1] Les Barclay (2003). “Propagation of Radiowaves.” 2nd ed. London, United Kingdom: The Institution
of Electrical Engineers. p129-144.
[2] J. D. Parsons (2000). “The Mobile Radio Propagation Channel”. Baffins Lane, Chichester, West
Sussex, England: John Wiley & Sons.
15. International Journal of Antennas (JANT) Vol.1, No.1, October 2015
15
[3] Recommendation ITU-R P.526-12: Propagation by diffraction, 2012
[4] J. Boersma (1960) "On a numerical method for the computation of Fresnel integrals”
TW 2, Math. Inst., Univ. of Groningen.
[5] J. B. Keller, "Geometrical theory of diffraction", J. Opt. Soc. Am., vol. 52, no. 2, pp. 116–130, 1962.
[6] R. G. Kouyoumjian and P. H. Pathak, "A uniform geometrical theory of diffraction for an edge in a
perfectly conducting surface," Proc. IEEE, vol. 62, pp. 1448–1461, November 1974.
[7] A. R. von Hippel (1954). “Dielectric Materials and Applications,”. Chapman & Hall, London.
Authors
Bawar Abid Abdalla Assist. Lecturer in the Department of Software Engineering, at Koya
University since 2012. B.Sc. degree in Computer Engineering from Koya University in 2010 .
M.Sc. degree in Information and Communication Engineering from Leicester University in 2012.