SunMaxx Installation Manual - TitanPower ALDH29 Flat Plate Collector - Flush Mount

Installation Guide
TitanPower ALDH29 Flat Plate Collector
www.SunMaxxSolar.com
Model Number
TitanPower-ALDH29
Mounting Type
Flush (Pitched Roof)
Free-Standing (Flat Roof)
X
X

SunMaxx Solar | 5042-5160 NY 206 Bainbridge NY 13733 | 1.877.786.6299 1.877.270.7875 fax | www.sunmaxxsolar.com
Components - 1 Collector Installation 31
Assembly & Installation - 1 Collector Installation 42
Table of Contents
Components - 2 Collector Installation 93
Assembly & Installation - 2 Collector Installation 104

1. Components - 1 Collector Installation
The packaging of the support structure consists of 2 cardboard boxes. The one include the profiles of the support structures and the second one the
accessories for the assembly.
The packages are including the following materials:
# Qty
Part #
Dimensions
Image
1 4 PS272BVDR-005
2 4 PS272BVDR-001
3 8 8x100 DIN 531
4 2
PS272BVDF-015
1.4”
5 2
PS272BVDF-013
2.8”
6 2
PS272BVDF-007
1.4” x 1.4” x 53.6”
7 26 M8 NUT DIN 6923
# Qty
Part #
Dimensions
Image
8 6 M8 x 30 LG DIN 933
9 4

2. Assembly & Installation - 1 Collector Installation
Step 1: Hook Assembly & Placement
1.1: Assemble the hooks according
to the upper figure.
1.2: Take off of the roof 1 or 2 tiles from the spot you choose as appropriate for the upper left
corner of the frame support. Place the perforated sheet plate on the rafter and on the upper
side of the tile batten, as figure on the left suggests, for better safety and grip. Adjust the “ς”
shaped Nr.1’s height, so as when the tiles are back to position again, the lower horizontal part
of hook Nr.1 stands between the upper and lower tile (figure on the left). Then place the tiles
again and seal.
1.3: Set as starting point the upper left hook. Then place the
upper right hook at distance X from the already placed left
hook. Tighten up the perforated plate on the rafter through
the most convenient holes. Then place lower right hook at
distance Y from the upper left and last the lower right hook
accordingly. After you make sure that all the wood screws are
tightened up and that the height is adjusted (see 1.2), place
the tiles to their positions.

Alternative Hook Type Placement
You are given the option to choose the type of hook you that fits your needs better. The following procedure gives the description for the use of this
hook (No.9). The placement dimensions are the same with the first option.
1.1: Prepare the four hooks No.9 according to the upper two figures. This hook consists of the main body, 3x nuts M10, a rubber sealing washer and
the plate that connects the hook with the collector’s support structure.
1.2: Take off of the roof 1 or 2 tiles from the spot you choose as
appropriate for the upper left corner of the frame support, until you
find a rafter and a batten and open a hole on the batten to tighten
the rod hook. Make a Φ12 hole to the corresponding spot of the
tile and then put back the tiles in position. Insert No.9 in the hole as
seen in the figures on the left and tighten up the main bolt on the
batten. Then place the rubber washer in the tile’s hole and tighten
washer on tile with the nut. There is no need for excessive force.
1.3: Having in mind the table with the dimensions X, Y provided in
the previews page as well as the corresponding directions given for
option 1, place the rest three hooks Nr.9, as seen in figure on the
left.
Follow the procedure presented in the second step (2.1, 2.2) in the following page, for the assembly of No.6 with No.4 and No.5 as well as the
figures above for the placing of the two No.6 on the hooks. The only difference between the two hook options are the hooks, thus phases 2.1 and
2.2 are identical.

Step 2: Assemble The Aluminum Profiles
2.1: Place the two No.4 clamps at the edges of one of the No.6 profile, as seen
in the figures above. Don’t tighten up the bolts at this phase.
2.2: Place the two No.5 clamps on the No.6 profile as seen above. Don’t
tighten up the bolts at this phase.
2.3: Tighten up the upper and lower support according to the figures above. Center the two aluminum profiles
relative to the hooks as well as to each other. Tighten up the bolts that connect the hooks to the supports. The
structure is ready for the collector.

Step 3: Place The Collectors
Both clamps No.4 and No.5 must secure the collector at this stage. Tighten the
M8 nuts in all parts to secure the collector on the support structure. Tighten
until the both types of clamps fit well on the collector like in the drawing on
the left.
ATTENTION: Pay maximum attention during tightening the nuts. Do not apply
extreme force as there is danger to harm the collector or destroy the accesso-
ries of the support structure. Apply the necessary force to secure the collector.
For the clamps No.4 it is necessary to apply opposite force in order to avoid
rotation of the aluminum part.

3. Components - 2 Collector Installation
# Qty
Part #
Dimensions
Image
1 6 PS272BVDR-005
2 6 PS272BVDR-001
3 12 8x100 DIN 531
4 4
PS272BVDF-015
1.4”
5 4
PS272BVDF-013
2.8”
6 2
PS272BVDF-007
1.4” x 1.4” x 53.6”
7 42 M8 NUT DIN 6923
# Qty
Part #
Dimensions
Image
8 42 M8 x 30 LG DIN 933
9 6

4. Assembly & Installation - 2 Collector Installation
Step 1: Hook Assembly & Placement
1.1: Assemble the hooks according to the upper
figure.
1.2: Take off of the roof 1 or 2 tiles from the spot you choose as appropriate
for the upper left corner of the frame support. Place the perforated sheet plate
on the rafter and on the upper side of the tile batten, as figure on the left sug-
gests, for better safety and grip. Then adjust the height of the ¨ς¨ shaped No.1,
in order to avoid contact with the tile. About 30mm clearance is OK. Repeat
procedure for all 6 hooks.
1.3: Set as starting point the upper left hook.
Then place the upper middle hook at distance
X from the already placed left hook. Tighten up
the perforated plate on the rafter through the
most convenient holes. Repeat for upper right
hook in distance X from the upper middle one.
Then place lower right hook at distance Y from
the upper left and repeat for the middle lower
and last the lower right hook accordingly. After
you make sure that all the wood screws are
tightened up and that the height is adjusted
(see 1.2), place the tiles to their positions.

Alternative Hook Type Placement
You are given the option to choose the type of hook you that fits your needs better. The following procedure gives the description for the use of this
hook (No.9). The placement dimensions are the same with the first option.
1.1: Prepare the six hooks No.9 according to the upper two figures. This hook consists of the main body, 3x nuts M10, a rubber sealing washer and
the plate that connects the hook with the collector’s support structure.
1.2: Take off of the roof 1 or 2 tiles from the spot you choose as
appropriate for the upper left corner of the frame support, until
you find a rafter and a batten and open a hole on the batten to
tighten the rod hook. Make a Φ12 hole to the corresponding
spot of the tile and then put back the tiles in position. Insert No.9
in the hole as seen in the figures on the left and tighten up the
main bolt on the batten. Then place the rubber washer in the
tile’s hole and tighten washer on tile with the nut. There is no
need for excessive force.
Follow the procedure presented in the second
step (2.1, 2.2) in the following page, for the
assembly of No.6 with No.4 and No.5 as well
as the figures above for the placing of the two
No.6 on the hooks. The only difference between
the two hook options are the hooks, thus
phases 2.1 and 2.2 are identical.

Step 2: Assemble The Aluminum Profiles
2.1: Place the two No.4 clamps at the edges of one of the No.6 profiles and the rest two in the mid-
dle of the same No.6, as seen in the figures above. Don’t tighten up the bolts at this phase. Prepare
the three M8 bolts for the three hooks at the lower side of the same profile as seen above.
2.2: Place the four No.5 clamps on the No.6 profile as seen above. Don’t tighten up the bolts at this phase. Prepare the three M8 bolts for the
three hooks at the lower side of the same profile as seen above.
Step 3: Place The Support Hooks
Tighten up the upper and lower support
according to the figures above. Center
the two aluminum profiles relative to the
hooks as well as to each other. Tighten up
the bolts that connect the hooks to the
supports. The structure is ready for the
collector.

Step 4: Place The Collectors
For the clamps No.4 it is necessary to
apply opposite force in order to avoid
rotation of the aluminum part.
Both clamps No.4 and No.5 must secure the collector at
this stage. Tighten the M8 nuts in all parts to secure the
collector on the support structure. Tighten until the both
types of clamps fit well on the collector like in the drawing
on the left.
ATTENTION: Pay maximum attention during tightening
the nuts. Do not apply extreme force as there is danger
to harm the collector or destroy the accessories of the
support structure. Apply the necessary force to secure the
collector.
3.1: Take care that the lower part
of the collector is in place. That
means that the collector’s support
frame is grabbed by the two No.5
clamps, as seen in the above figure
on the left. Don’t tighten up yet the
bolts on No.5. You can also attach
the No.4 clamps on the collectors’
sides.

5042-5160 NY 206 Bainbridge NY 13733 | 1.877.786.6299 1.888.270.7875 fax
www.SunMaxxSolar.com

SunMaxx Installation Manual - TitanPower ALDH29 Flat Plate Collector - Flush Mount

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

Viewers also liked

Viewers also liked (12)

Similar to SunMaxx Installation Manual - TitanPower ALDH29 Flat Plate Collector - Flush Mount

Similar to SunMaxx Installation Manual - TitanPower ALDH29 Flat Plate Collector - Flush Mount (20)

More from SunMaxx Solar

More from SunMaxx Solar (8)

Recently uploaded

Recently uploaded (20)

SunMaxx Installation Manual - TitanPower ALDH29 Flat Plate Collector - Flush Mount