13. THẺ RFID PROXIMITY
NHÓM 9
Tiêu chuẩn kỹ thuật:
- Sử dụng tần số: 125 KHz
- Khoảng cách thẻ với đầu đọc: 2 – 15 cm
- Thời gian đọc từ 1 – 2 ms
- Môi trường nhiệt độ: 20 – 85 độ C
- Kích thước : Dài 86 mm, Rộng 54mm,
Dày 0.76 mm & Dài 85.7, Rộng 54, 1.8 mm
- Giá cả: 6000đ – 7000đ
- Địa chỉ: Cty TNHH XNK TM Ánh
Dương, www.anhphuongtech.com ......
14. NHÓM 9
ĐẦU ĐỌC THẺ RFID PROXIMITY
Một số tính năng của đầu đọc thẻ RFID Proximity
125KHz:
- Hỗ trợ đọc thẻ chuẩn: Proximity (125KHz).
- Hệ điều hành: Windows® 7, 8, Vista, XP, 2000, Server
2008 & 2003, Mac OS X, Linux, Windows® CE.
- Cổng giao tiếp: USB.
- Tiêu chuẩn chất lượng: USB, CE, UL, FCC, VCCI,
WEEE, RoHS, WHQL.
- Kích thước: L:70 x W:70 x H:10 (mm).
- Trọng lượng: ~ 70g.
- Giá cả: 150.000đ – 1.500.000đ
- Liên hệ: www.anhphuongtech.com, Cty TNHH
VNAPPTECH, www.hshop.vn ,…
15. NHÓM 9
RFID KEY TAG
Thông số kỹ thuật:
- Chất liệu: PVC
- Trọng lượng: 6g ~ 12g
- Color: xám, xanh dương, vàng, đỏ, trắng và tím
- Nhiệt độ làm việc: -10 ℃ và 50 ℃
- Tần số làm việc : 125Khz
- Khoảng cách đọc: 0 – 8 cm
- Giá cả: 18.000 – 58.000đ
- Liên hệ: Cty TNHH DV TM KT TL, Cty CP ĐT
CN Lê Hoàng, www.hshop.vn , ….
16. VÒNG ĐEO CỔ TAY RFID
NHÓM 9
THÔNG SỐ KỸ THUẬT:
- Chất liệu: silicone
- Kích thước: 227 * 16 * 2mm hoặc tùy chỉnh
- Tần số: 125KHz, 13.56MHz, 860 ~ 960MHz
- Chip: TK4100, Mifare S50, H3
- Đọc khoảng cách: 1-5cm cho LF / HF; 1-20cm cho UHF
- Màu sắc: đỏ, vàng, xanh, đen, xanh lá cây...
- Ứng dụng: câu lạc bộ, hồ bơi, sự kiện, công viên nước, thư viện...
- Liên hệ: www.ungdungrfid.com , www.vnapptech.com.vn
….
17. NHÓM 9
THẺ RFID GẮN CHO ĐỘNG VẬT
Thông số kỹ thuật:
- Chất liệu: Polyme
- Tầng số hoạt động 125KHz / 134.2KHz /
13.56MHz / 860MHz ~ 960MHz.
- Khoảng cách đọc từ 0 ~ 10m, tùy đầu đọc, loại
thẻ và nhu cầu.
- Bộ nhớ 64bits, 256 bits, 512bits, 1KBytes.
- Có thể đọc và ghi dữ liệu lên tới 100.000 lần.
- Dữ liệu lưu trữ trên 10 năm.
- Liên hệ: www.ungdungrfid.com.vn ,
18. THẺ MIFARE
NHÓM 9
Tiêu chuẩn kỹ thuật:
- Tần số: 13.56 MHz (theo chuẩn ISO/IEC 14443A)
- Dung lượng nhớ: 512 byte (Mifare Ultraligh), 1K
(Mifare S50), 4 K (Mifare S70)
- Khoảng cách thẻ với đầu đọc thẻ: 2.5 – 10 cm
- Thời gian đọc/ghi: 1-2 ms
- Số lần ghi xóa: > 100,000 lần
- Thời gian lưu dữ liệu trên thẻ: 10 năm
- Kích thước: 85.6 x 54 x 0.81 mm
- Liên hệ: www.ungdungrfid.com.vn
www.thegioibodam.vn …
19. NHÓM 9
MIFARE READER
Thông số kỹ thuật đầu đọc ghi Mifare:
- Kích cỡ 95 x 60 x 25 mm.
- Trọng lượng 250g ±10%.
- Lắp ráp trên bề mặt, không thấm nước.
- Khoảng cách đọc: 3 ~ 5 cm.
- Tần số: HF 13.56MHz.
- Nguồn cấp 5VDC±10%, 12VDC±10%.
- Kết nối: USB.
- Nhiệt độ hoạt động -15°C ~ 55°C.
- Độ ẩm 20%~90% RH, không ngưng tụ
- Liên hệ: www.ungdungrfid.com.vn , www.thegioibodam.vn ..
20. THẺ GẮN TRÊN ĐỒ TRANG SỨC
NHÓM 9
Thông số kỹ thuật:
- Vật liệu: Giấy / PVC / PET
- Kích thước: 120 x 15 x 0.25 mm
- Trọng lượng : ~ 1g
- Tiêu chuẩn giao thức : ISO 15693, ISO 18000 – 6C
- Loại Chip: I-Code-SLI, Alien H3
- Tần số hoạt động: 13.56Mhz, 860Mhz – 960MHZ
- Chế độ làm việc: Đọc – Ghi
- Bộ nhớ: EPC 96 bit, 512 bit
- Khoảng cách đọc: với chip I-Code-SLI: 0 – 10cm, với chip
Alien H3: 0 – 100cm ( phụ thuộc vào Reader)
- Lưu trữ dữ liệu: trên 10 năm
- Số lần đọc ghi: trên 100.000 lần
- Liên hệ: www.ungdungrfid.com.vn
22. NHÓM 9
TEM NHÃN RFID
Tem nhãn RFID ứng dụng phổ biến đế dán lên hộp, thùng
carton, quần áo, tài sản, hậu cần...
- Tiêu chuẩn: ISO / IEC 18000-6C (EPC Gen2 C1).
- Tần số: LF – HF – UHF( thông dụng 860Mhz – 960Mhz)
- Chất liệu ăng-ten: Nhôm.
- Chip: H3.
- Nhiệt độ hoạt động: -20 ℃ ~ 80 ℃.
- Khoảng cách đọc: 0-8 m.
- Liên hệ: www.ungdungrfid.com.vn
www.vnapptech.vn
…
23. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Thông số kỹ thuật đầu đọc thẻ cảm ứng
RFID VNC3000:
• CPU: Freescale 800MHz.
• RAM: 256MB.
• Giao thức: EPC C1 GEN2/ISO1800-6C.
• Tần số: 865-868MHz.
• Nguồn: 1W (+10dBm ~ +30dBm).
• Cấu hình ăng-ten: 3dbi; (0-1.5m).
• Giao tiếp: USB 2.0.
• Giao thức wifi: IEEE802.11 b/g.
• Pin: Li-ion (3.7 V/5200 mAh).
• Kích thước: 13.5 x 7.5 x 2.9 cm.
• Trọng lượng: 330 g.
• Liên hệ: www.123mua.vn
www.vnapptech.vn
25. NHÓM 9
TEMPERATURE SENSOR ACTIVE
Thông số vật lý:
- Phạm vi đọc lên đến 80m (phụ thuộc và đầu đọc, anten và cấu
hình phần mềm
- Loại thẻ: Read Only
- Vật liệu: ABS, chịu nhiệt, màu trắng/đen
- Kích thước : 75x50x7.5 mm
- Dung lượng pin: 1 ~ 2 năm (có thể thay thế)
- Trọng lượng: 25g
- Tín hiệu điều chế: GFSK
- Tốc độ giao tiếp: 1 chiều 1Mbps
- Tần số : 2.4Ghz
- Dòng làm việc: <16mA
- Nhiệt độ làm việc: -200C đến 450C
- Độ ẩm : <85%RH
- Chịu va đập: <1m (rơi tự do)
- Liên hệ: www.alibaba.com …..
26. ACTIVE VIBRATION SENSOR RFID
NHÓM 9
Thông số kỹ thuật:
- Độ nhạy: 200mV/g
- Tần số cộng hưởng: 90Hz
- Khoảng cách: 0 – 90 m
- Tần số hoạt động : 2.4Ghz – 2.5Ghz
- Nguồn làm việc: 12 – 18 µA, 3V
- Điều chế: GFSK
- Tốc độ dữ liệu: 1Mbps
- Chống xung đột: 100 tags có thể đọc đồng thời
- Loại thẻ: Read Only
- Thời lượng pin: 4 năm
- Kích thước: 90 x 31 x 11 mm
- Liên hệ: www.gaorfid.com ….
27. NHÓM 9
ACTIVE FUILD SENSOR RFID
Thông số kỹ thuật:
- Tần số làm việc: 433.92 Mhz
- Phạm vi : ~200 ft
- Điều chế : ASK
- Loại thẻ: Read Only
- Chu kì đọc: 3s trên 1 chu kỳ
- Dung lượng pin : > 7 năm
- Nhiệt độ làm việc: -200C đến 700C
- Độ dài dây: 304.79mm
- Kích thước: 43.18 x 73.15 x 12.7 mm
- Trọng lượng: 18.71 g
- Ứng dụng: phát hiện rò rỉ chất lỏng ở sàn nhà, tường, các
đường ống…
- Liên hệ: www.gaorfid.com
29. NHÓM 9
CONTAINER SERCURITY
THÔNG SỐ KỸ THUẬT:
- Phạm vi đọc/ viết : ~ 140 M
- Nguồn: pin Lithium 3.6 V
- Dung lượng pin: hơn 5 năm
- Báo dung lượng pin: Có
- Tần số làm việc: 433.92 Mhz
- Tốc độ dữ liệu: 27.778Kb/s
- Điều chế : FSK
- Màu sắc : Đen
- Trọng lượng: 690g – 715g
- Kẹp : 50mm theo tiêu chuẩn ISO Container
- Nhiệt độ làm việc: -300C đến 700C
- Độ ẩm: 10% đến 90%
- Chịu va đập: rơi tự do < 1M
- Khả năng ghi: ~ 100.000 lần
- Bộ nhớ người dùng: 128KB
- Bộ nhớ cảm biến: 32KB
- Mã xác minh: 32 bit ID (có thể sửa)
- Liên hệ: www.gaorfid.com
30. NHÓM 9
CONTAINER SERCURITY
Thông số kỹ thuật:
- Tần số làm việc: UHF band, 860 – 960 MHz,
- Phạm vi đọc: ~ 22M
- Giao thức UHF GEN 2: chuẩn ISO 18000-6c
1064-bit không bay hơi
720-bit cho người dùng
hỗ trợ 96-bit EPC numbers
- Dữ liệu tồn tại: 10 năm
- Kích thước: 118 x 35 x 6.6 mm
- Trọng lượng : 32 g
- Nhiệt độ làm việc: -400C đến 700C
- Độ ẩm: 0 -85% RH
- Chống sốc và rung: Tiêu chuẩn IEC 60068-2-6, IEC 60068-2-31
- Liên hệ: www.gaorfid.com
31. NHÓM 9
CƠ CHẾ ĐỌC GHI
T5557 Read/Write RFID:
The Atmel T5557 is a 330 bit
Read/Write RFID transponder
operating in the 125Khz band.
Its memory is structured in 10
blocks of 33 bits.
This is structured as 7 blocks of 32
bits of read/write data.
32. NHÓM 9
CƠ CHẾ ĐỌC GHI
Among the many functions available the T5557 RFID
transponder is capable of:
Selectable Modulation Encoding. Manchester, FSK, PSK, Biphase,
NRZ.
Password protected Read and Write
Direct access block read and write.
33. NHÓM 9
CƠ CHẾ ĐỌC GHI
The memory structure of the T5557 transponder is shown here:
The T5557 rfid transponder
has two blocks of
Traceability data.
This information contains
manufacturer codes, lot
numbers, and other
such data for tracing the
source of the transponder.
34. NHÓM 9
CƠ CHẾ ĐỌC GHI
Configuration data:
Here is a description of some of the more important configuration bit details.
Bits 16 - 20: Determine the Encoding protocol upon start up
A bit pattern of 10000 selects Manchester Encoding
35. NHÓM 9
CƠ CHẾ ĐỌC GHI
Bits 12 - 14: Determine the Bit rate of the data transmitted by the
transponder to the reader. A bit pattern of 101 selects a bit rate of 64 Field
Cycles per bit.
Bits 25 - 27: Determine the maximum block address transmitted in
standard read mode. For the T5557 RFID transponder this value can be
from 0 to 7.
36. NHÓM 9
CƠ CHẾ ĐỌC GHI
Bit 28: When Set this bit activates the Password mode. In Password mode
all blocks need a password to be sent before they can be read or written.
The password required is stored in block 7.
Bit 0: Setting Bit 0 to logic 1 will prevent any further writes of the selected
block.
37. NHÓM 9
CƠ CHẾ ĐỌC GHI
When the tag enters the RF field and powers up it loads the information
stored in the configuration block.
This tells it what bit rate and encoding scheme to transmit in. It then enters
into Regular Read Mode.
In Regular Read Mode the tag will start to transmit its data starting from
Block 1, and ending in the block number selected by the Max Block bits of
the configuration register.
38. NHÓM 9
CƠ CHẾ ĐỌC GHI
Often the beginning of each transmission is
preceeded with a special terminator sequence that
allows the RFID reader to syncronize to the first
block sent. This terminator sequence can be
activated by setting bit 29 of the configuration
block.
39. NHÓM 9
CƠ CHẾ ĐỌC GHI
When transmitting in Standard read mode with a terminator active and Max
Block set to 4 the data blocks appear as such
40. NHÓM 9
CƠ CHẾ ĐỌC GHI
Sending Read and Write Commands.
All commands to the transponder are initiated by producing a "Start gap".
To produce the Start gap the RFID reader will turn off the field for a
period of between 10-50 field cycles.
Then to send either 1 or 0 bits the RF field is turned on again for a period
that varies depending on which bit is being transmitted. With a 1 bit the
field will be active for a period between 48 to 63 field cycles, while for a
0 bit the field will be active for a period between 16 to 31 field cycles.
41. NHÓM 9
CƠ CHẾ ĐỌC GHI
To send a read block command a logic 1 is sent, followed by the page value bit
(0 for page 0), a 0 bit, and the 3 address bits corresponding to the block addresss
of the block required to be read. If the command is understood by the T5557
transponder it will start to transmit the required block in a continuous loop.
42. NHÓM 9
CƠ CHẾ ĐỌC GHI
Here we have a standard Write and a Protected Write to a block. The
Protected Write commands require the password to be sent along with
the relevant data.
Also the Lock bit (L) is sent. A 0 bit will allow the block to be rewritten,
while a 1 bit will turn this block into a Read Only location, where no
further writes are permitted.
43. NHÓM 9
CƠ CHẾ ĐỌC GHI
So sánh giữa Đọc và Ghi tag:
Ghi tag mất nhiều thời gian hơn đọc, vì ghi tag cần nhiều bước (xóa dữ liệu
tồn tại, ghi dữ liệu mới, kiểm tra...).
Khoảng cách giữa thẻ Tag và Reader ở chế độ ghi phải gần hơn chế độ đọc, vì
ghi dễ bị nhiễu, đồng thời đảm bảo năng lượng đầy đủ đến thẻ Tag.
Năng lượng khi ghi cũng cao hơn khi đọc.
45. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
46. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
47. ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
48. ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
49. ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
50. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Security Problems of RFID:
• Eaves Dropping
• Hot-listing
• Replay attack
• Cloning
• Denial of Service (DoS)
51. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Secure RFID system should have protection
against the following threats:
o Unauthoried reading of data
o The placing of a foreign data carrier within
the interrogation zone with the intention of
gaining unauthorized access to a building
or receiving service without payment
o Eavesdropping into radio communications
and relaying the data to imitate a genuine
data carrier
52. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
53. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Cryptography (mã hóa)
&
Authentication (xác thực)
54. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Cryptography System
• Plain Text: Thông tin trước
khi được mã hóa. (clear text)
• Ciphertext: Thông tin sau khi
đã được mã hóa
• Encryption: Mã hóa
• Decryption: Giải mã
• Key: Thành phần quan trọng
trong việc mã hóa và giải mã
55. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Four Basic Service of Cryptography
• Confidentiality (Tính bảo mật)
• Authentication (Tính xác thực, gốc)
• Interity (Tính toàn vẹn)
• Non-repudation (Tính không thể
chối bỏ)
56. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Mutual Symmetrical Authentication
57. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Mutual Symmetrical Authentication
• The secret keys are never transmitted over the airwaves, only encrypted random
numbers are transmitted.
• Two random numbers are always encrypted at the same time. The token can be
encrypted using any algorithm.
• The strict use of random numbers from two independent sources (transponder ,
reader) means that recording an authentication sequence for playback at a later date
(replay attack) would fail.
• A random key (session key) can be calculated from the random numbers generated ,
in order to cryptologic secure the subsequent data transmission.
RFID Systems and Data Security
58. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Authentication Using Derived Keys
59. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Encrypted Data Transfer
60. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Encrypted Data Transfer
Cryptological procedures are used
to protect against both passive and
active attacks. To achieve this, the
transmitted data (plain text) can
be encrypted prior to transmission
so that a potential attacker can
no longer draw conclusions about
the actual content of the message
(plain text).
61. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Encrypted Data Transfer
Encrypted data transmission always
takes place according to the same
pattern.
The Transmission data (plain text) is
transformed into cipher data
(ciphertext) using secret algorithm.
Without knowing the encryption
algorithm and the secret key K a
potential attacker is unable to inter-
pret the recorded data. It is not
possible to recreate the transmission
data from the cipher data
62. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Encrypted Data Transfer
The cipher data is transformed
back to its original form in the
receiver using the secret key K and
the secret algorithm
(→decryption,deciphering).
63. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
RFID Systems and Data Security
Ecrypted Data Transfer
65. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Q&A
We have somesimple
question for you guys!!
66. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Q&A
Khái niệm Eaves Dropping là gì?
a. Là giao thức mã hóa của hệ thống
bảo mật RFID
b. Khả năng nhân bản thẻ để lấy cấp
thông tin
c. Là giao thức xác nhận môi môi
trường RFID
d. Là nguy cơ nghe lén để lấy cắp thông
tin
Let’s begin!
67. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Q&A
Bit nào sau đây dùng để kích hoạt chế độ
‘Password Mode’
a. 23
b. 28
c. 29
d. 32
Wowww
Good job!
68. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Q&A
Chiều dài antenna lưỡng cực trên tab
được xác định bằng:
a. Một nửa bước sóng
b. Bằng độ dài bước sóng
c. Gấp đối bước sóng
d. Tùy thuộc vào độ nhạy thu của tag và
công suất phát của reader.
Well done!
69. NHÓM 9
ĐẦU ĐỌC CẦM TAY VNC 3000
Thank you for your attending.
12-14 tốc độ Bit
25-27: số địa chỉ khối tối đa truyền trong chế độ đọc
Bit0: lên logic 1 thì sẽ ngăn chặn việc ghi thêm dữ liệu lên khối đã chọn
Thông thường, vào đầu mỗi truyền, được bắt đầu bằng một chuỗi terminator đặc biệt, cho phép người đọc RFID để đồng bộ hóa với khối đầu tiên được gửi đi. chuỗi terminator này có thể được kích hoạt bằng cách thiết lập bit 29 của khối cấu hình.
Khi truyền tải trong tiêu chuẩn chế độ đọc với một terminator hoạt động và Max Khối đặt thành 4 khối dữ liệu xuất hiện như vậy
RF được bật trở lại trong một thời gian mà thay đổi tùy thuộc vào bit được truyền đi. Bit1 48-64 Field Cycles, Bit0 16-31 FC
Hình 1: Nếu lệnh được hiểu bởi transponder T5557 nó sẽ bắt đầu truyền các khối cần thiết trong một vòng lặp liên tục.
Hình 2: Ở đây, nếu bit PWD được thiết lập trong khối cấu hình, các mật khẩu được lưu trữ tại Lô 7 cũng phải được gửi để đọc các khối cần thiết.
Khi sử dụng Protected Writed Command thì mật khẩu cũng phải gửi cùng với nh~ dữ liệu có liên quan.
Hot-listing: Hot listing refers to the process of building a database of books and their associated tag numbers (the hotlist) and then using an unauthorized reader to determine who is checking out items on the hotlist. (Attack has special interests in certain items)
Mật mã và xác thực.
Confidentiality: The intruder cannot read the encrypted message from the ciphertext.
Authentication: It should be possible for the receiver of a message to ascertain its orgin; an intruder should not be able to masquerade as someone else.
Interity: It should be possible for the receiver of a message to verify that it has not been modified in transit an intruder cannot substiture a false message for a legitimate one.
Non-repudation: A sender should not be able to falsely deny later that he sent a message.