ASOKA TECHNOLOGIES
(B.TECH/M.TECH ELECTRICAL PROJECTS USING MATLAB/SIMULINK)
WE OFFER ACADEMIC MATLAB SIMULATION PROJECTS FOR
1. ELECTRICAL AND ELECTRONICS ENGINEERING [EEE]
2. POWER ELECTRONICS AND DRIVES [PED]
3. POWER SYSTEMS [PS]….etc
We will develop your OWN IDEAS and your IEEE Papers with extension if necessary and also we give guidance for publishing papers…
For Further Details Call Us @
0-9347143789/9949240245
For Abstracts of IEEE papers and for any Queries mail to: asokatechnologies(gmail) and also visit asokatechnologies(blogspot)
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Residential Community Load Management based on Optimal Design of Standalone H...Asoka Technologies
Microgrids being an important entity in the distribution system, and to get their full advantages
by incorporating maximum distributed generation, standalone hybrid renewable energy systems (HRESs), being environmentally-safe and economically-efficient, are considered as the promising solution to electrify remote areas where the grid power is not available. In this work, a techno-economic investigation with an optimal design of HRES is presented to fulfill the domestic electricity need for a residential area of the Sherani district in the Province of Baluchistan, Pakistan. Nine case studies based on PV/wind/diesel/battery are analyzed based on net present cost (NPC), cost of energy (COE), and emission to decide the feasible solution. HOMER tool is utilized to accomplish modeling and simulation for economic analysis and optimal sizing. Simulation results demonstrated that HRES with PV-wind-battery is the most viable option for the specified area, and the optimal sizing of components are also obtained with $ 28,620 NPC and 0.311 $/kWh COE which shows 81.65% reduction in cost and 100% preserving in toxic emission while fulfilling 100% energy demand with 67.3% of excess energy. Furthermore, MATLAB/Simulink modeling for the optimally designed system is built for technical analysis while its effectiveness is proved by keeping dc and ac buses voltage constant, safe operating range of battery state of charge (SOC) with active power balance between HRES components, as well as efficient ac voltage quality, regardless of generation disturbances and load fluctuations. The output signal has total harmonic distortion (THD) of 0.30% as compared to 5.44% with the conventional control scheme. The novelty lies in the sequential application of both HOMER and MATLAB simulations of the proposed HRES model and validation of the proposition for the studied area; by using and implementing model predictive control (MPC) of a reconfigurable inverter.
Comparison of Photovoltaic Array Maximum Power Point Tracking TechniquesAsoka Technologies
The many different techniques for maximum power point tracking of photovoltaic (PV) arrays are discussed. The techniques are taken from the literature dating back to the earliest methods. It is shown that at least 19 distinct methods have been introduced in the literature, with many variations on implementation. This paper should serve as a convenient reference for future work in PV power generation.
Modified cascaded h bridge multilevel inverter for hybrid renewable energy ap...Asoka Technologies
Renewable energy sources and technologies have the potential to provide solutions to the longstanding energy problems being faced by developing countries. The renewable energy sources like wind energy, solar energy, geothermal energy, ocean energy, biomass energy and fuel cell technology can be used to overcome energy shortage in India. This paper proposes a modified multi-level inverter (MLI) topology for Hybrid Renewable Energy Sources (HRES) and a design of hybrid solar-wind power generation model with 9-level, 13-level and 17-level inverter topologies. A HRES connected to a modified Cascaded H-Bridge Multi Level Inverter (CHB-MLI) is developed, whose switches are controlled using Artificial Neural Network (ANN) model. The proposed hybrid energy system model consists of 10 Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) that intend to give 17 levels of output voltage. The proposed topology performs effectively with reduced number of components and reduced Total Harmonic Distortion (THD). The performance of the proposed system is analyzed by designing the model in MATLAB/SIMULINK environment. The simulation results of the proposed inverter for the HRES application are compared with the results of the existing topologies to show the effectiveness of the proposed model.
ASOKA TECHNOLOGIES
(B.TECH/M.TECH ELECTRICAL PROJECTS USING MATLAB/SIMULINK)
WE OFFER ACADEMIC MATLAB SIMULATION PROJECTS FOR
1. ELECTRICAL AND ELECTRONICS ENGINEERING [EEE]
2. POWER ELECTRONICS AND DRIVES [PED]
3. POWER SYSTEMS [PS]….etc
We will develop your OWN IDEAS and your IEEE Papers with extension if necessary and also we give guidance for publishing papers…
For Further Details Call Us @
0-9347143789/9949240245
For Abstracts of IEEE papers and for any Queries mail to: asokatechnologies(gmail) and also visit asokatechnologies(blogspot)
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Residential Community Load Management based on Optimal Design of Standalone H...Asoka Technologies
Microgrids being an important entity in the distribution system, and to get their full advantages
by incorporating maximum distributed generation, standalone hybrid renewable energy systems (HRESs), being environmentally-safe and economically-efficient, are considered as the promising solution to electrify remote areas where the grid power is not available. In this work, a techno-economic investigation with an optimal design of HRES is presented to fulfill the domestic electricity need for a residential area of the Sherani district in the Province of Baluchistan, Pakistan. Nine case studies based on PV/wind/diesel/battery are analyzed based on net present cost (NPC), cost of energy (COE), and emission to decide the feasible solution. HOMER tool is utilized to accomplish modeling and simulation for economic analysis and optimal sizing. Simulation results demonstrated that HRES with PV-wind-battery is the most viable option for the specified area, and the optimal sizing of components are also obtained with $ 28,620 NPC and 0.311 $/kWh COE which shows 81.65% reduction in cost and 100% preserving in toxic emission while fulfilling 100% energy demand with 67.3% of excess energy. Furthermore, MATLAB/Simulink modeling for the optimally designed system is built for technical analysis while its effectiveness is proved by keeping dc and ac buses voltage constant, safe operating range of battery state of charge (SOC) with active power balance between HRES components, as well as efficient ac voltage quality, regardless of generation disturbances and load fluctuations. The output signal has total harmonic distortion (THD) of 0.30% as compared to 5.44% with the conventional control scheme. The novelty lies in the sequential application of both HOMER and MATLAB simulations of the proposed HRES model and validation of the proposition for the studied area; by using and implementing model predictive control (MPC) of a reconfigurable inverter.
Comparison of Photovoltaic Array Maximum Power Point Tracking TechniquesAsoka Technologies
The many different techniques for maximum power point tracking of photovoltaic (PV) arrays are discussed. The techniques are taken from the literature dating back to the earliest methods. It is shown that at least 19 distinct methods have been introduced in the literature, with many variations on implementation. This paper should serve as a convenient reference for future work in PV power generation.
Modified cascaded h bridge multilevel inverter for hybrid renewable energy ap...Asoka Technologies
Renewable energy sources and technologies have the potential to provide solutions to the longstanding energy problems being faced by developing countries. The renewable energy sources like wind energy, solar energy, geothermal energy, ocean energy, biomass energy and fuel cell technology can be used to overcome energy shortage in India. This paper proposes a modified multi-level inverter (MLI) topology for Hybrid Renewable Energy Sources (HRES) and a design of hybrid solar-wind power generation model with 9-level, 13-level and 17-level inverter topologies. A HRES connected to a modified Cascaded H-Bridge Multi Level Inverter (CHB-MLI) is developed, whose switches are controlled using Artificial Neural Network (ANN) model. The proposed hybrid energy system model consists of 10 Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) that intend to give 17 levels of output voltage. The proposed topology performs effectively with reduced number of components and reduced Total Harmonic Distortion (THD). The performance of the proposed system is analyzed by designing the model in MATLAB/SIMULINK environment. The simulation results of the proposed inverter for the HRES application are compared with the results of the existing topologies to show the effectiveness of the proposed model.
Integration of PV, Battery and Supercapacitor in Islanded MicrogridAsoka Technologies
Nowadays battery is used to stabilize the DC bus voltage but battery has low power density and high energy density. Whereas the supercapacitor has high power density but low energy density. So, for high energy and power density the integration of battery and supercapacitor is more efficient. It is more challenging to integrate the different sources. So it is required a control strategy to integrate the battery and supercapacitor and provide continuous power to the load. It has also shown that the battery and supercapacitor charged in access mode of power and discharged in deficit mode of power. In this paper proposed a new approach to control the power and dc bus voltage.
El proyecto europeo DURABLE tiene el objetivo de acelerar el despliegue de energías renovables en la región atlántica (España, Portugal, Francia, Irlanda y Reino Unido), mediante la aplicación de drones y robots para la operación y mantenimiento de sistemas de energía eólica y solar. La aplicación de esta tecnología permitirá automatizar tareas de inspección y reparación, reduciendo los costes y favoreciendo la producción de energía limpia.
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...Asoka Technologies
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
The scientific principle of “mechanical springs” was described by the British physicist Robert
Hooke in the 1660’s. Since then, there has not been any further development of the Hooke’s law
in the electric regime. In this paper, this technological gap is filled by the development of
“electric springs.” The scientific principle, the operating modes, the limitations, and the practical
realization of the electric springs are reported. It is discovered that such novel concept has huge
potential in stabilizing future power systems with substantial penetration of intermittent
renewable energy sources. This concept has been successfully demonstrated in a practical power
system setup fed by an ac power source with a fluctuating wind energy source. The electric
spring is found to be effective in regulating the mains voltage despite the fluctuation caused by
the intermittent nature of wind power. Electric appliances with the electric springs embedded can
be turned into a new generation of smart loads, which have their power demand following the
power generation profile. It is envisaged that electric springs, when distributed over the power
grid, will offer a new form of power system stability solution that is independent of information
and communication technology.
Nonostante i vantaggi economici e ambientali per veicoli elettrici ibridi plug-in (PHEV), l'aumento dell'utilizzo di PHEV solleva nuove preoccupazioni per la distribuzione di energia.
Abengoa is developing innovative software capable of modelling railway electrification systems and their environment. It is comprised of a series of modules that are expected to revolutionize the sector due to the fact that for the first time, there is an integration in terms of electrification design, passenger safety and that of the installations as well as energy efficiency, both in terms of design and operation, regardless of the type of catenary technology, electricity supply system or rolling stock type.
A three-input hybrid system for solar car is designed in this project. It consists of one unidirectional input power port and two bidirectional power ports with a storage element. Depending on utilization state of the battery, three different power operation modes are defined for the converter. Battery charging in the system is carried out from the amorphous solar panel mounted on the body and a solar energy harvesting charging station. Since the solar energy is directly given to the DC load, the efficiency of the system will improve. The capacitor which is connected to the lead acid battery will charge at off peak hours and discharge during the acceleration time of the car. In this proposed system energy wasted in the brakes are also recovered and used to charge the lead acid battery. Hence competent Hybrid Electric Vehicle was developed by using super capacitor and regenerative braking scheme.
Integration of PV, Battery and Supercapacitor in Islanded MicrogridAsoka Technologies
Nowadays battery is used to stabilize the DC bus voltage but battery has low power density and high energy density. Whereas the supercapacitor has high power density but low energy density. So, for high energy and power density the integration of battery and supercapacitor is more efficient. It is more challenging to integrate the different sources. So it is required a control strategy to integrate the battery and supercapacitor and provide continuous power to the load. It has also shown that the battery and supercapacitor charged in access mode of power and discharged in deficit mode of power. In this paper proposed a new approach to control the power and dc bus voltage.
El proyecto europeo DURABLE tiene el objetivo de acelerar el despliegue de energías renovables en la región atlántica (España, Portugal, Francia, Irlanda y Reino Unido), mediante la aplicación de drones y robots para la operación y mantenimiento de sistemas de energía eólica y solar. La aplicación de esta tecnología permitirá automatizar tareas de inspección y reparación, reduciendo los costes y favoreciendo la producción de energía limpia.
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...Asoka Technologies
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
The scientific principle of “mechanical springs” was described by the British physicist Robert
Hooke in the 1660’s. Since then, there has not been any further development of the Hooke’s law
in the electric regime. In this paper, this technological gap is filled by the development of
“electric springs.” The scientific principle, the operating modes, the limitations, and the practical
realization of the electric springs are reported. It is discovered that such novel concept has huge
potential in stabilizing future power systems with substantial penetration of intermittent
renewable energy sources. This concept has been successfully demonstrated in a practical power
system setup fed by an ac power source with a fluctuating wind energy source. The electric
spring is found to be effective in regulating the mains voltage despite the fluctuation caused by
the intermittent nature of wind power. Electric appliances with the electric springs embedded can
be turned into a new generation of smart loads, which have their power demand following the
power generation profile. It is envisaged that electric springs, when distributed over the power
grid, will offer a new form of power system stability solution that is independent of information
and communication technology.
Nonostante i vantaggi economici e ambientali per veicoli elettrici ibridi plug-in (PHEV), l'aumento dell'utilizzo di PHEV solleva nuove preoccupazioni per la distribuzione di energia.
Abengoa is developing innovative software capable of modelling railway electrification systems and their environment. It is comprised of a series of modules that are expected to revolutionize the sector due to the fact that for the first time, there is an integration in terms of electrification design, passenger safety and that of the installations as well as energy efficiency, both in terms of design and operation, regardless of the type of catenary technology, electricity supply system or rolling stock type.
A three-input hybrid system for solar car is designed in this project. It consists of one unidirectional input power port and two bidirectional power ports with a storage element. Depending on utilization state of the battery, three different power operation modes are defined for the converter. Battery charging in the system is carried out from the amorphous solar panel mounted on the body and a solar energy harvesting charging station. Since the solar energy is directly given to the DC load, the efficiency of the system will improve. The capacitor which is connected to the lead acid battery will charge at off peak hours and discharge during the acceleration time of the car. In this proposed system energy wasted in the brakes are also recovered and used to charge the lead acid battery. Hence competent Hybrid Electric Vehicle was developed by using super capacitor and regenerative braking scheme.
Control of a Three-Phase Hybrid Converter for a PV Charging StationAsoka Technologies
Hybrid boost converter (HBC) has been proposed to replace a dc/dc boost converter and a dc/ac converter to reduce conversion stages and switching loss. In this paper, control of a three-phase HBC in a PV charging station is designed and tested. This HBC interfaces a PV system, a dc system with hybrid plugin electrical vehicles (HPEVs) and a three-phase ac grid. The control of the HBC is designed to realize maximum power point tracking (MPPT) for PV, dc bus voltage regulation, and ac voltage or reactive power regulation. A test bed with power electronics switching details is built in MATLAB/SimPowersystems for validation. Simulation results demonstrate the feasibility of the designed control architecture. Finally, lab experimental testing is conducted to demonstrate HBC’s control performance.
A Vision for a Holistic and Smart Grid with High Benefits to SocietyStephen Lee
Presented on Dec 2, 2009 as a keynote speech to the 2009 T&D Asia Conference in Bangkok and followed by moderating a round-table discussion of top utility executives in SE Asia.
Latest Electrical Mini Projects For EEE Studentselprocus
Simple Mini Projects For EEE Can Be Implemented By Using Microcontroller And Different Technologies. We Hope That Our Innovative Projects For EEE Students Offer Immense Help And Make Them Select Suitable Projects For Their Project Work.
https://www.elprocus.com
Visit our page to get more ideas on Electrical Mini Projects developed by professionals.
Elprocus provides free verified electronic projects kits around the world with abstracts, circuit diagrams, and free electronic software. We provide guidance manual for Do It Yourself Kits (DIY) with the modules at best price along with free shipping.
Energy management and control strategy of photovoltaic battery hybrid distrib...Asoka Technologies
Photovoltaic (PV)/battery hybrid power units have attracted vast research interests in recent years. For the conventional distributed power generation systems with PV/battery hybrid power units, two independent power converters, including a unidirectional dc_dc converter and a bidirectional converter, are normally required. This paper proposes an energy management and control strategy for the PV/battery hybrid distributed power generation systems with only one integrated three-port power converter. As the integrated bidirectional converter shares power switches with the full-bridge dc_dc converter, the power density and the reliability of the system is enhanced. The corresponding energy management and control strategy are proposed to realize the power balance among three ports in different operating scenarios, which comprehensively takes both the maximum power point tracking (MPPT) benefit and the battery charging/discharging management into consideration. The simulations are conducted using the Matlab/Simulink software to verify the operation performance of the proposed PV/battery hybrid distributed power generation system with the corresponding control algorithms, where the MPPT control loop, the battery charging/discharging management loop are enabled accordingly in different operating scenarios.
Control strategy for power flow management in a pv system supplying dc loadsAsoka Technologies
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
Similar to Power Electronics Matlab simulink Projects Research Help (20)
Operation “Blue Star” is the only event in the history of Independent India where the state went into war with its own people. Even after about 40 years it is not clear if it was culmination of states anger over people of the region, a political game of power or start of dictatorial chapter in the democratic setup.
The people of Punjab felt alienated from main stream due to denial of their just demands during a long democratic struggle since independence. As it happen all over the word, it led to militant struggle with great loss of lives of military, police and civilian personnel. Killing of Indira Gandhi and massacre of innocent Sikhs in Delhi and other India cities was also associated with this movement.
Macroeconomics- Movie Location
This will be used as part of your Personal Professional Portfolio once graded.
Objective:
Prepare a presentation or a paper using research, basic comparative analysis, data organization and application of economic information. You will make an informed assessment of an economic climate outside of the United States to accomplish an entertainment industry objective.
June 3, 2024 Anti-Semitism Letter Sent to MIT President Kornbluth and MIT Cor...Levi Shapiro
Letter from the Congress of the United States regarding Anti-Semitism sent June 3rd to MIT President Sally Kornbluth, MIT Corp Chair, Mark Gorenberg
Dear Dr. Kornbluth and Mr. Gorenberg,
The US House of Representatives is deeply concerned by ongoing and pervasive acts of antisemitic
harassment and intimidation at the Massachusetts Institute of Technology (MIT). Failing to act decisively to ensure a safe learning environment for all students would be a grave dereliction of your responsibilities as President of MIT and Chair of the MIT Corporation.
This Congress will not stand idly by and allow an environment hostile to Jewish students to persist. The House believes that your institution is in violation of Title VI of the Civil Rights Act, and the inability or
unwillingness to rectify this violation through action requires accountability.
Postsecondary education is a unique opportunity for students to learn and have their ideas and beliefs challenged. However, universities receiving hundreds of millions of federal funds annually have denied
students that opportunity and have been hijacked to become venues for the promotion of terrorism, antisemitic harassment and intimidation, unlawful encampments, and in some cases, assaults and riots.
The House of Representatives will not countenance the use of federal funds to indoctrinate students into hateful, antisemitic, anti-American supporters of terrorism. Investigations into campus antisemitism by the Committee on Education and the Workforce and the Committee on Ways and Means have been expanded into a Congress-wide probe across all relevant jurisdictions to address this national crisis. The undersigned Committees will conduct oversight into the use of federal funds at MIT and its learning environment under authorities granted to each Committee.
• The Committee on Education and the Workforce has been investigating your institution since December 7, 2023. The Committee has broad jurisdiction over postsecondary education, including its compliance with Title VI of the Civil Rights Act, campus safety concerns over disruptions to the learning environment, and the awarding of federal student aid under the Higher Education Act.
• The Committee on Oversight and Accountability is investigating the sources of funding and other support flowing to groups espousing pro-Hamas propaganda and engaged in antisemitic harassment and intimidation of students. The Committee on Oversight and Accountability is the principal oversight committee of the US House of Representatives and has broad authority to investigate “any matter” at “any time” under House Rule X.
• The Committee on Ways and Means has been investigating several universities since November 15, 2023, when the Committee held a hearing entitled From Ivory Towers to Dark Corners: Investigating the Nexus Between Antisemitism, Tax-Exempt Universities, and Terror Financing. The Committee followed the hearing with letters to those institutions on January 10, 202
Introduction to AI for Nonprofits with Tapp NetworkTechSoup
Dive into the world of AI! Experts Jon Hill and Tareq Monaur will guide you through AI's role in enhancing nonprofit websites and basic marketing strategies, making it easy to understand and apply.
2024.06.01 Introducing a competency framework for languag learning materials ...Sandy Millin
http://sandymillin.wordpress.com/iateflwebinar2024
Published classroom materials form the basis of syllabuses, drive teacher professional development, and have a potentially huge influence on learners, teachers and education systems. All teachers also create their own materials, whether a few sentences on a blackboard, a highly-structured fully-realised online course, or anything in between. Despite this, the knowledge and skills needed to create effective language learning materials are rarely part of teacher training, and are mostly learnt by trial and error.
Knowledge and skills frameworks, generally called competency frameworks, for ELT teachers, trainers and managers have existed for a few years now. However, until I created one for my MA dissertation, there wasn’t one drawing together what we need to know and do to be able to effectively produce language learning materials.
This webinar will introduce you to my framework, highlighting the key competencies I identified from my research. It will also show how anybody involved in language teaching (any language, not just English!), teacher training, managing schools or developing language learning materials can benefit from using the framework.
2024.06.01 Introducing a competency framework for languag learning materials ...
Power Electronics Matlab simulink Projects Research Help
1. P O W E R E L E C T R O N I C S
M A T L A B S I M U L I N K P R O J E C T S
www.matlabsimulation.com/power-electronics-matlab-simulink-projects/
2. Fundamental Application of Power Electronics Projects
Here are some of the applications focus on which become developed by using Power electronics,
Robot control Satellite power
system
Speech Coding
and also Error
correction model
MEMS accelerometer
Three-phase
electric motor
Battery
Management and
also Grid System
3. Advanced Concepts in Energy Harvesting
Here are some of the advanced concepts on which become energy harvesting by using Power electronics,
Resonance
shielding
Beam scanning and
also Power control
strategy
Far distanced power
transfer
Solar based power
transfer
Hybrid inductive and
also capacitive system
Road lane electric
vehicle
4. Topmost Notions in Renewable Energy
Greenhouse gas emission
Wind energy conversion
Solar panel tracker Pilot Protection
Heterogeneous energy
system
The recent ideas in renewable energy which developed under power electronics projects,