The document describes a student editing a photo of a guitar in black and white using various tools. The student used the Magnetic Lasso Tool to select the guitar, copied and pasted it, then adjusted the hue and saturation in black and white mode. Next, the student used Color Balance to adjust the color of just the guitar. Finally, the student flattened the image and was happy with the results.

1. Portrait Shoot
By Megan Robinson

2. First I selected ‘Magnetic Lasso Tool’ to go around the guitar then I copied it and pasted it.
On the same place where the guitar is.
I clicked on ‘Image’ then went to ‘Adjustments’,
clicked on ‘Black & White’. On the right, it shows
what comes up when I clicked ‘Black & White’
and I clicked Tint, and changed little of ‘Hue’ and
‘Saturation’ until I was happy with it.

3. This is what I did on the left when I
turned this image into black and white
by using tint.
First I clicked on the guitar because I only
wanted to change on that so I clicked on
‘Image’ then chose ‘Adjustments’ and clicked
on ‘Color Balance’.
Then I changed the colour on the
guitar and stopped until I was happy
with it.
Then I right clicked on
the right to ‘Flatten
Image’ because I copied
the guitar and pasted it
so I wanted it to be all
one image now. Now I
have finished it and I am
happy with what I have
edited and on the next
page, you can see more
of what I changed.
This is what it looks like and I really
like it, the guitar stands out more.

5. This is original image and I
wanted to make changes. To do
that I clicked ‘Image’ and then
went on ‘Adjustments’ and
choose ‘Brightness/Contrast’. I
changed the brightness to 26
then I changed the contrast to
49.
I went all around the girl by using
‘Magnetic Lasso Tool’. Then I copied and
pasted it. On the first image, I decided to
go on ‘Image’ then ‘Adjustments’ and
clicked on ‘Color Balance’. I made some
changes to make it more green and make
it more like spring/summer. But I haven’t
change the colour balance on the girl so
that’s why I copied and pasted her. Then I
cropped the image to use the rule of third.
I have finished it and put on the next slide.

7. This is original image and I
wanted to make changes. To do
that I clicked ‘Image’ and then
went on ‘Adjustments’ and
chose ‘Brightness/Contrast’. I
changed the brightness to 21
then I changed the contrast to
50.
I went all around the girl and
the guitar by using ‘Magnetic
Lasso Tool’. I copied and pasted
it. I went on the original image
then I clicked ‘Image’ and
‘Adjustments’ then ‘Vibrance’ I
changed vibrance to +24 then I
changed saturation to +74.
I went on ‘Image’ and
clicked on ‘Adjustments
then ‘Color Balance’. I have
been changing the colour
and chose what I am
happy with. I have finished
now which shows on the
next page.

9. This is original image and I
wanted to change it. So to do
this, the image is not very
straight so I used ‘Rectangular
Marquee Tool’. I went all
around the image then I turned
the image to make more
straight. I want to crop this
image because you can see the
black bit so I cropped these
sections out.
I want to change the
brightness and contrast.
First I clicked on ‘Image’
then ‘Adjustments’ and
finally
‘Brightness/Contrast’.
Changed the brightness
to 6 and changed the
contrast to 53.
I decided to crop it more, this
time, I cropped the image to
make it bigger and more
focussed on the shed and the
girls rather than outside the
shed. Finally I decided to make
the image black and white and
clicked on ‘Tint’. I changed the
‘Hue’ and ‘Saturation’ until I
liked the image. The final image
is shown on the next page.