This document provides definitions and explanations of various OBDII parameters or PIDs that are used by OBDII systems and scantools for vehicle diagnostics and system interrogation. It defines common PIDs like fuel system status, engine coolant temperature, short and long term fuel trims, oxygen sensor voltages and currents, and explains the differences between conventional and wideband oxygen sensors. It also provides context on OBDII emissions testing and the check engine light.
1. The document provides information about the Isuzu 4JH1-TC diesel engine management system, which uses a Bosch VP44 injection pump controlled by an engine control module (ECM) and pump control unit (PSG) that communicate via CAN-bus.
2. The ECM controls fuel injection quantity and timing by exchanging data with the PSG, which actuates the injection pump. They share sensor data and commands via analog signals and CAN-bus.
3. The document outlines the components, electrical circuits, diagnostic procedures and trouble codes for technicians servicing the engine management system.
351 Sistema de Inyeccion Common Rail Motor 3 0l TDI V6.pdfjcarrey
Este documento describe el sistema de inyección Common Rail utilizado en el motor TDI 3.0L V6. El sistema utiliza un acumulador de alta presión (rail) que suministra combustible a alta presión a los inyectores. Esto permite una inyección flexible con múltiples ciclos y una presión variable para mejorar la eficiencia de combustible y reducir las emisiones. El sistema está controlado por el sistema de gestión del motor Bosch EDC 16 CP.
El documento describe el sistema de inyección diesel de riel común, incluyendo sus componentes, funcionamiento y ventajas sobre sistemas anteriores. El sistema mantiene una presión de inyección constante independientemente de las revoluciones del motor gracias a almacenar el combustible a alta presión en un riel común. Esto proporciona mayor flexibilidad y rendimiento en todo el rango de revoluciones. Los principales componentes son el riel, bomba de alta presión, inyectores y unidad de control electrónica que gestiona el proceso de in
1. El documento describe las conexiones de varios módulos de encendido para diferentes vehículos. Incluye detalles sobre los colores de cable y funciones de cada circuito en los conectores.
2. Se proporcionan especificaciones para módulos de encendido de GM, Ford, Chevrolet, Toyota y otros fabricantes.
3. La información sobre conexiones puede usarse para diagnosticar y reparar sistemas de encendido.
El motor 1.9 TDi grupo VAG - Seat Audi Volkswagen Skodadegarden
El documento describe el motor diésel 1.9 TDi de Volkswagen. Introdujo innovaciones como la inyección directa de combustible a alta presión y el control electrónico, lo que mejoró el rendimiento, consumo y emisiones. Estuvo disponible en varias potencias entre 90 y 130 caballos de fuerza. Tuvo éxito comercial debido a su eficiencia y prestaciones similares a un motor de gasolina.
Los motores del Actros son motores diésel V6 y V8 duraderos y potentes. Tienen bajo consumo de combustible debido a su alta presión de inyección y sistema de gestión electrónica que optimiza la mezcla aire-combustible. Ofrecen largos intervalos de mantenimiento e individuación gracias a su monitorización electrónica.
Este manual fornece esquemas elétricos, desenhos de posição de componentes e lista de componentes para caminhões Scania. Explica os dois tipos de sistemas elétricos ADR e regulamentos relevantes. Inclui informações sobre marcação de cabos e tradução de termos nos esquemas.
1. The document provides information about the Isuzu 4JH1-TC diesel engine management system, which uses a Bosch VP44 injection pump controlled by an engine control module (ECM) and pump control unit (PSG) that communicate via CAN-bus.
2. The ECM controls fuel injection quantity and timing by exchanging data with the PSG, which actuates the injection pump. They share sensor data and commands via analog signals and CAN-bus.
3. The document outlines the components, electrical circuits, diagnostic procedures and trouble codes for technicians servicing the engine management system.
351 Sistema de Inyeccion Common Rail Motor 3 0l TDI V6.pdfjcarrey
Este documento describe el sistema de inyección Common Rail utilizado en el motor TDI 3.0L V6. El sistema utiliza un acumulador de alta presión (rail) que suministra combustible a alta presión a los inyectores. Esto permite una inyección flexible con múltiples ciclos y una presión variable para mejorar la eficiencia de combustible y reducir las emisiones. El sistema está controlado por el sistema de gestión del motor Bosch EDC 16 CP.
El documento describe el sistema de inyección diesel de riel común, incluyendo sus componentes, funcionamiento y ventajas sobre sistemas anteriores. El sistema mantiene una presión de inyección constante independientemente de las revoluciones del motor gracias a almacenar el combustible a alta presión en un riel común. Esto proporciona mayor flexibilidad y rendimiento en todo el rango de revoluciones. Los principales componentes son el riel, bomba de alta presión, inyectores y unidad de control electrónica que gestiona el proceso de in
1. El documento describe las conexiones de varios módulos de encendido para diferentes vehículos. Incluye detalles sobre los colores de cable y funciones de cada circuito en los conectores.
2. Se proporcionan especificaciones para módulos de encendido de GM, Ford, Chevrolet, Toyota y otros fabricantes.
3. La información sobre conexiones puede usarse para diagnosticar y reparar sistemas de encendido.
El motor 1.9 TDi grupo VAG - Seat Audi Volkswagen Skodadegarden
El documento describe el motor diésel 1.9 TDi de Volkswagen. Introdujo innovaciones como la inyección directa de combustible a alta presión y el control electrónico, lo que mejoró el rendimiento, consumo y emisiones. Estuvo disponible en varias potencias entre 90 y 130 caballos de fuerza. Tuvo éxito comercial debido a su eficiencia y prestaciones similares a un motor de gasolina.
Los motores del Actros son motores diésel V6 y V8 duraderos y potentes. Tienen bajo consumo de combustible debido a su alta presión de inyección y sistema de gestión electrónica que optimiza la mezcla aire-combustible. Ofrecen largos intervalos de mantenimiento e individuación gracias a su monitorización electrónica.
Este manual fornece esquemas elétricos, desenhos de posição de componentes e lista de componentes para caminhões Scania. Explica os dois tipos de sistemas elétricos ADR e regulamentos relevantes. Inclui informações sobre marcação de cabos e tradução de termos nos esquemas.
DIAGRAMA ELECTRICO 336DL CAT. Renr95870001juanManuel1001
This document provides information on electrical system components and symbols for a 330D and 336D excavator. It includes:
1) A table listing connector and component locations by schematic and machine location.
2) Pages of electrical schematic symbols and their meanings.
3) A section defining harness and wire symbols such as colors, gauges and connector identification codes.
The document is a reference for technicians servicing the excavator's electrical system. It identifies all electrical connectors, components and their machine locations for troubleshooting.
O documento discute a alimentação do módulo de injeção eletrônica e possíveis defeitos. A alimentação do módulo depende da linha 15, que recebe +12V da chave de ignição, e da linha 30, que fornece alimentação permanente da bateria. Problemas com essas linhas, como bloqueadores de furto ou emendas malfeitas, podem causar falhas no módulo. É importante verificar as tensões de alimentação, especialmente durante a partida do motor.
390 Cambio de doble embrague 0AM de 7 marchas.pdfjcarrey
El documento describe el nuevo cambio de doble embrague de 7 velocidades de Volkswagen. El cambio utiliza dos embragues secos y transmisiones parciales independientes que permiten cambiar de marcha sin interrupción de la fuerza de tracción. Esto mejora la eficiencia y reduce el consumo de combustible en comparación con versiones anteriores. El cambio representa un avance tecnológico que amplía la ventaja de Volkswagen sobre la competencia.
Este documento descreve o sistema de controle do motor EMS S6 da Scania. Ele inclui:
1) Uma descrição dos principais componentes do EMS S6 e seus locais no motor.
2) Detalhes sobre os sensores de rotação do motor, pressão do ar de admissão, temperatura do ar de admissão e outros.
3) Como a unidade de controle do EMS S6 monitora esses sensores para controlar o motor.
337471410-Transmision-automatica-4R75W.pdfIsaul Saltos B
Es un sistema de marcha, o bien, de cambio de velocidades automático. Este mecanismo se encarga de controlar la dirección, la velocidad y el movimiento del vehículo de forma autónoma. La principal diferencia que hay entre una caja de transmisión automática y una manual, es que la estándar se encarga de bloquear varios engranes, para que así el conductor sea el que haga los cambios.QUÉ VENTAJAS TIENE UNA CAJA DE TRANSMISIÓN AUTOMÁTICA?
- Brinda una conducción más cómoda y segura para el conductor- Son más eficientes en el ahorro de combustible que las manuales (en ciudades)
- Tienen mayor durabilidad y confiabilidad que las transmisiones estándar
- El funcionamiento, desempeño y comportamiento en el camino es mucho mayor
- ¡Te olvidas de la marcha! Al tener una transmisión automática, no tienes que preocuparte por hacer constantemente los cambios de velocidad¿QUÉ DESVENTAJAS TIENEN?
- Si prefieres la conducción en carretera, entonces esta transmisión no es para ti
- Los coches que tienen este tipo de transmisión se encarecen mucho más
- En caso de que la caja falle, el costo de reparación es muy alto.
Sin importar si tu vehículo cuenta con una transmisión manual o con una caja de transmisión automática, es muy importante que el coche cuente con las llantas adecuadas. Ya sea que prefieres la comodidad, lo silencioso o lo deportivo, elige las que mejor vayan contigo.
Y tú, ¿qué tipo de transmisión te acomoda más? La manual o la automática. ¡No olvides dejarnos tus comentarios!Transmisión automática para conductores principiantes
Definitivamente, los autos con transmisión automática son mucho más fáciles de manejar que los manuales. No tienes que preocuparte por el embrague, y tampoco estar pendiente de la palanca de cambios entre los cambios de marchaComo resultado de esto, los autos con una transmisión automática ya sea CVT, DCT o un conversor de torque tradicional, son muy fáciles de aprender a manejar. Hay menos posibilidades de cometer errores y más cosas de las que puedes apartar la vista. Además, esto te ofrece un beneficio adicional, te sentirás mucho más relajado manejando un auto automático en ciudades con alto tráfico.
De la misma manera, cuenta con una transición mucho más suave entre las marchas, resultando en un viaje más agradable. Y debido a que hay menos posibilidades de que los engranajes rechinen accidentalmente, la transmisión en sí misma tiene menos probabilidades de fallar
El documento describe el sistema EOBD (diagnóstico a bordo) para motores diésel. El EOBD monitorea componentes que podrían afectar las emisiones de gases de escape y enciende una luz de advertencia si los niveles de emisiones superan los límites. El EOBD es estándar en la Unión Europea y permite que organismos oficiales revisen el sistema.
Este documento técnico proporciona especificaciones e instrucciones para el armado del motor QR25DE de 2.5 litros utilizado en varios modelos de Nissan. Incluye detalles sobre la cabeza de cilindros, válvulas, árbol de levas, bielas, cigüeñal y sincronización, así como recomendaciones para el armado. El objetivo es garantizar un ajuste y sellado perfectos para el corazón del motor.
Este documento proporciona información sobre el nuevo motor de gasolina de 3 cilindros y 12 válvulas de 1.2 litros de cilindrada de Seat. El motor pesa poco debido al uso de aluminio, proporciona 47 kW de potencia a 5400 rpm y 112 Nm de par a 3000 rpm, y cumple con la normativa EU IV de emisiones contaminantes. El documento describe las características mecánicas clave del motor como el bloque de aluminio, la culata de distribución, el sistema de lubricación y refrigeración, y el sistema
Este documento describe el sistema de diagnóstico de un vehículo Toyota. Explica que la ECU del motor supervisa los sensores y actuadores y registra códigos de diagnóstico (DTC) si detecta una falla. Los DTC pueden confirmarse mediante un probador manual conectado al vehículo o mediante el parpadeo de la luz de fallas del motor. También describe los diferentes tipos de sistemas de diagnóstico a bordo y cómo funciona el proceso de diagnóstico.
This document provides information about a universal IMMO VAG immobilizer/emulator. It can be used in cases where original keys are missing, the immobilizer unit has an electrical or logical defect, or the car's engine is being changed. The emulator can emulate VAG immobilizer types IMMO1 and IMMO2 used from 1995-2004 in Audi, VW, Seat, and Skoda models. Installation involves disconnecting the data link between the ECU and original immobilizer and connecting the emulator instead.
17 chevrolet zafira 2004 2.2 lt 64 terminales(1)Alex cuevas
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
El documento describe el funcionamiento del sistema de inyector bomba en un motor diésel de 1.9 litros. El sistema de inyector bomba combina la bomba de inyección y el inyector en una sola unidad para cada cilindro, eliminando las tuberías de alta presión. El sistema genera una alta presión de inyección de hasta 2,050 bares para lograr una pulverización fina del combustible y un control preciso de la cantidad y el momento de la inyección.
Este documento lista vários sensores e componentes de um veículo, incluindo sensores de pressão e temperatura dos gases de escape, sensor de pressão do turbo, sensor de fase CKP, sensor de nível de combustível e óleo do motor.
El documento describe las características técnicas del motor 1,4 ltr., 16 V, 55 kW con balancines flotantes de rodillo. Incluye una descripción general del diseño y funcionamiento del motor, así como sus datos técnicos principales como cilindrada, potencia, par motor, gestión del motor y tratamiento de gases de escape.
Tecnología de Motores de Combustión Interna:
Reconstrucción manual de Motor Toyota 4K.
Reparación y calibración técnica-empírica.
Vídeo final del arranque:
https://www.youtube.com/watch?v=_19eH6KMYKM&feature=youtu.be
O documento fornece uma lista extensa de códigos de diagnóstico e seus respectivos componentes em máquinas Caterpillar equipadas com controles eletrônicos. Os códigos incluem identificadores de componentes, módulos e tipos de falha para ajudar na manutenção e diagnóstico de problemas.
Este documento describe las características técnicas del motor 2.0 L 16V TDi utilizado por primera vez en el modelo Seat Altea. Se destacan las mejoras con respecto a motores diésel anteriores como pistones refrigerados, culata de 4 válvulas por cilindro y gestión electrónica Bosch EDC16. El motor cumple con la normativa EU IV y ofrece una potencia máxima de 103 kW y un par máximo de 320 Nm.
El documento describe las características generales del motor y el sistema de inyección electrónica del Hyundai Accent. Explica que el motor está equipado con un sistema MPFI que permite a los estudiantes aplicar conocimientos adquiridos. Describe los componentes del sistema de inyección como el ECM, sensores, bomba de combustible y filtro. Resalta las ventajas del sistema MPFI como consumo reducido, mayor potencia y menor contaminación.
This document provides information about onboard diagnostic (OBD) modes and parameters for Toyota and Lexus vehicles. It lists the 10 standard OBD modes and describes what data each mode provides, such as current diagnostic data (Mode 1), freeze frame data of emission failures (Mode 2), stored diagnostic trouble codes (Mode 3), and abilities to clear information (Mode 4) and view oxygen sensor test results (Mode 5). It also explains continuous versus non-continuous emission monitor tests and readiness test status.
This document provides an overview of On-Board Diagnostics Generation II (OBD-II) systems. It describes the purpose and functions of OBD-II, including standardized diagnostic trouble codes, monitors that test different vehicle systems, enabling criteria for monitors to run, and the drive cycle needed to run all tests. It also explains how technicians can use features like freeze frame data and fuel trim values as diagnostic aids.
DIAGRAMA ELECTRICO 336DL CAT. Renr95870001juanManuel1001
This document provides information on electrical system components and symbols for a 330D and 336D excavator. It includes:
1) A table listing connector and component locations by schematic and machine location.
2) Pages of electrical schematic symbols and their meanings.
3) A section defining harness and wire symbols such as colors, gauges and connector identification codes.
The document is a reference for technicians servicing the excavator's electrical system. It identifies all electrical connectors, components and their machine locations for troubleshooting.
O documento discute a alimentação do módulo de injeção eletrônica e possíveis defeitos. A alimentação do módulo depende da linha 15, que recebe +12V da chave de ignição, e da linha 30, que fornece alimentação permanente da bateria. Problemas com essas linhas, como bloqueadores de furto ou emendas malfeitas, podem causar falhas no módulo. É importante verificar as tensões de alimentação, especialmente durante a partida do motor.
390 Cambio de doble embrague 0AM de 7 marchas.pdfjcarrey
El documento describe el nuevo cambio de doble embrague de 7 velocidades de Volkswagen. El cambio utiliza dos embragues secos y transmisiones parciales independientes que permiten cambiar de marcha sin interrupción de la fuerza de tracción. Esto mejora la eficiencia y reduce el consumo de combustible en comparación con versiones anteriores. El cambio representa un avance tecnológico que amplía la ventaja de Volkswagen sobre la competencia.
Este documento descreve o sistema de controle do motor EMS S6 da Scania. Ele inclui:
1) Uma descrição dos principais componentes do EMS S6 e seus locais no motor.
2) Detalhes sobre os sensores de rotação do motor, pressão do ar de admissão, temperatura do ar de admissão e outros.
3) Como a unidade de controle do EMS S6 monitora esses sensores para controlar o motor.
337471410-Transmision-automatica-4R75W.pdfIsaul Saltos B
Es un sistema de marcha, o bien, de cambio de velocidades automático. Este mecanismo se encarga de controlar la dirección, la velocidad y el movimiento del vehículo de forma autónoma. La principal diferencia que hay entre una caja de transmisión automática y una manual, es que la estándar se encarga de bloquear varios engranes, para que así el conductor sea el que haga los cambios.QUÉ VENTAJAS TIENE UNA CAJA DE TRANSMISIÓN AUTOMÁTICA?
- Brinda una conducción más cómoda y segura para el conductor- Son más eficientes en el ahorro de combustible que las manuales (en ciudades)
- Tienen mayor durabilidad y confiabilidad que las transmisiones estándar
- El funcionamiento, desempeño y comportamiento en el camino es mucho mayor
- ¡Te olvidas de la marcha! Al tener una transmisión automática, no tienes que preocuparte por hacer constantemente los cambios de velocidad¿QUÉ DESVENTAJAS TIENEN?
- Si prefieres la conducción en carretera, entonces esta transmisión no es para ti
- Los coches que tienen este tipo de transmisión se encarecen mucho más
- En caso de que la caja falle, el costo de reparación es muy alto.
Sin importar si tu vehículo cuenta con una transmisión manual o con una caja de transmisión automática, es muy importante que el coche cuente con las llantas adecuadas. Ya sea que prefieres la comodidad, lo silencioso o lo deportivo, elige las que mejor vayan contigo.
Y tú, ¿qué tipo de transmisión te acomoda más? La manual o la automática. ¡No olvides dejarnos tus comentarios!Transmisión automática para conductores principiantes
Definitivamente, los autos con transmisión automática son mucho más fáciles de manejar que los manuales. No tienes que preocuparte por el embrague, y tampoco estar pendiente de la palanca de cambios entre los cambios de marchaComo resultado de esto, los autos con una transmisión automática ya sea CVT, DCT o un conversor de torque tradicional, son muy fáciles de aprender a manejar. Hay menos posibilidades de cometer errores y más cosas de las que puedes apartar la vista. Además, esto te ofrece un beneficio adicional, te sentirás mucho más relajado manejando un auto automático en ciudades con alto tráfico.
De la misma manera, cuenta con una transición mucho más suave entre las marchas, resultando en un viaje más agradable. Y debido a que hay menos posibilidades de que los engranajes rechinen accidentalmente, la transmisión en sí misma tiene menos probabilidades de fallar
El documento describe el sistema EOBD (diagnóstico a bordo) para motores diésel. El EOBD monitorea componentes que podrían afectar las emisiones de gases de escape y enciende una luz de advertencia si los niveles de emisiones superan los límites. El EOBD es estándar en la Unión Europea y permite que organismos oficiales revisen el sistema.
Este documento técnico proporciona especificaciones e instrucciones para el armado del motor QR25DE de 2.5 litros utilizado en varios modelos de Nissan. Incluye detalles sobre la cabeza de cilindros, válvulas, árbol de levas, bielas, cigüeñal y sincronización, así como recomendaciones para el armado. El objetivo es garantizar un ajuste y sellado perfectos para el corazón del motor.
Este documento proporciona información sobre el nuevo motor de gasolina de 3 cilindros y 12 válvulas de 1.2 litros de cilindrada de Seat. El motor pesa poco debido al uso de aluminio, proporciona 47 kW de potencia a 5400 rpm y 112 Nm de par a 3000 rpm, y cumple con la normativa EU IV de emisiones contaminantes. El documento describe las características mecánicas clave del motor como el bloque de aluminio, la culata de distribución, el sistema de lubricación y refrigeración, y el sistema
Este documento describe el sistema de diagnóstico de un vehículo Toyota. Explica que la ECU del motor supervisa los sensores y actuadores y registra códigos de diagnóstico (DTC) si detecta una falla. Los DTC pueden confirmarse mediante un probador manual conectado al vehículo o mediante el parpadeo de la luz de fallas del motor. También describe los diferentes tipos de sistemas de diagnóstico a bordo y cómo funciona el proceso de diagnóstico.
This document provides information about a universal IMMO VAG immobilizer/emulator. It can be used in cases where original keys are missing, the immobilizer unit has an electrical or logical defect, or the car's engine is being changed. The emulator can emulate VAG immobilizer types IMMO1 and IMMO2 used from 1995-2004 in Audi, VW, Seat, and Skoda models. Installation involves disconnecting the data link between the ECU and original immobilizer and connecting the emulator instead.
17 chevrolet zafira 2004 2.2 lt 64 terminales(1)Alex cuevas
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
El documento describe el funcionamiento del sistema de inyector bomba en un motor diésel de 1.9 litros. El sistema de inyector bomba combina la bomba de inyección y el inyector en una sola unidad para cada cilindro, eliminando las tuberías de alta presión. El sistema genera una alta presión de inyección de hasta 2,050 bares para lograr una pulverización fina del combustible y un control preciso de la cantidad y el momento de la inyección.
Este documento lista vários sensores e componentes de um veículo, incluindo sensores de pressão e temperatura dos gases de escape, sensor de pressão do turbo, sensor de fase CKP, sensor de nível de combustível e óleo do motor.
El documento describe las características técnicas del motor 1,4 ltr., 16 V, 55 kW con balancines flotantes de rodillo. Incluye una descripción general del diseño y funcionamiento del motor, así como sus datos técnicos principales como cilindrada, potencia, par motor, gestión del motor y tratamiento de gases de escape.
Tecnología de Motores de Combustión Interna:
Reconstrucción manual de Motor Toyota 4K.
Reparación y calibración técnica-empírica.
Vídeo final del arranque:
https://www.youtube.com/watch?v=_19eH6KMYKM&feature=youtu.be
O documento fornece uma lista extensa de códigos de diagnóstico e seus respectivos componentes em máquinas Caterpillar equipadas com controles eletrônicos. Os códigos incluem identificadores de componentes, módulos e tipos de falha para ajudar na manutenção e diagnóstico de problemas.
Este documento describe las características técnicas del motor 2.0 L 16V TDi utilizado por primera vez en el modelo Seat Altea. Se destacan las mejoras con respecto a motores diésel anteriores como pistones refrigerados, culata de 4 válvulas por cilindro y gestión electrónica Bosch EDC16. El motor cumple con la normativa EU IV y ofrece una potencia máxima de 103 kW y un par máximo de 320 Nm.
El documento describe las características generales del motor y el sistema de inyección electrónica del Hyundai Accent. Explica que el motor está equipado con un sistema MPFI que permite a los estudiantes aplicar conocimientos adquiridos. Describe los componentes del sistema de inyección como el ECM, sensores, bomba de combustible y filtro. Resalta las ventajas del sistema MPFI como consumo reducido, mayor potencia y menor contaminación.
This document provides information about onboard diagnostic (OBD) modes and parameters for Toyota and Lexus vehicles. It lists the 10 standard OBD modes and describes what data each mode provides, such as current diagnostic data (Mode 1), freeze frame data of emission failures (Mode 2), stored diagnostic trouble codes (Mode 3), and abilities to clear information (Mode 4) and view oxygen sensor test results (Mode 5). It also explains continuous versus non-continuous emission monitor tests and readiness test status.
This document provides an overview of On-Board Diagnostics Generation II (OBD-II) systems. It describes the purpose and functions of OBD-II, including standardized diagnostic trouble codes, monitors that test different vehicle systems, enabling criteria for monitors to run, and the drive cycle needed to run all tests. It also explains how technicians can use features like freeze frame data and fuel trim values as diagnostic aids.
The document provides information about European OBD systems, including what components and emissions can be monitored, the data that must be stored, and signals that are available through the diagnostic connector. It specifies the requirements for fault code storage, extinguishing and erasing fault codes, and details the limits for when the malfunction indicator light must be activated. It also gives information on fuel trim monitoring and the various communication standards and interfaces that are used for EOBD diagnostics.
The document provides information about OBDII systems and instructions for using the Creader V+ diagnostic tool. It includes sections on general OBDII information, product descriptions, tool setup instructions, and operations like reading codes, erasing codes, and special tests. Key details covered are OBDII standards, diagnostic trouble codes, monitor readiness, tool interfaces, connection process, and navigating code reading and other diagnostic functions.
This is the user manual of Topdon AL201.
>> READ MORE: https://www.obdadvisor.com/best-topdon-obd2-review/
Here is a detailed review of the Topdon scan tool based on my own experience.
Check it out to get the REVIEW and some NOTES about using this scanner.
Veepeak OBDCheck VP30 User Manual
>> READ MORE: https://www.obdadvisor.com/best-veepeak-obd2-scanner-review/
Here is a detailed review of the Veepeak OBD2 adapters:
- Features and functions
- Compatibility
- Pros and cons
Check it out to get the REVIEW and some NOTES about using this scanner based on my own experience.
1) The document discusses interpreting serial data from vehicles, specifically parameters related to fuel and spark control. It explains that fuel and spark calculations are primarily based on only a few key sensors measuring engine load, speed, temperature, and oxygen levels.
2) Six sensors that most impact fuel and spark calculations are outlined in detail, along with their functions and typical values.
3) Fuel trim values are described as indicators of how close the fuel mixture is to the target air-fuel ratio, with long-term and short-term fuel trims helping to adjust the fuel mixture as needed.
This is the user manual of Veepeak OBDCheck VP39.
>> READ MORE: https://www.obdadvisor.com/best-veepeak-obd2-scanner-review/
Here is a detailed review of the Veepeak adapters based on my own experience, including:
- Compatibility
- Features and Functions
- Pros and Cons
Check it out to get the REVIEW and some NOTES about using the scanner.
ABSOLUTE SCAN "INSIDE YOUR MACHINE"
ON-BOARD DIAGNOSTICS ENGINEERING
DIAGNÓSTICO OBD2 DE VEHÍCULOS
DIAGNÓSTICO OBD2 ESTÁNDAR Y SISTEMAS ESPECÍFICOS
DIAGNÓSTICO EN VIVO
DIAGNÓSTICO Y PROGRAMACIÓN DE MERCEDES-BENZ
ALTO SEGUENCOMA 1RA MESETA CALLE 1A #62 Z. SUR LA PAZ; BOLIVIA, PLURINATIONAL STATE OF
TELÉFONOS: 71223957, 61123909 Y 2782666
SOUTH AMERICA
IRJET - IoT based Gas Level Detection and the Automatic Booking of the GasIRJET Journal
This document summarizes an IoT-based system that detects the level of gas in a cylinder and automatically books a new cylinder. The system uses a load cell to measure the weight of the gas cylinder and detect the gas level. A gas sensor detects any gas leaks. When the gas level reaches below 20%, an Arduino sends an SMS alert to the user and books a new cylinder via GSM module. The system was implemented using an Arduino Uno, load cell, gas sensor, LCD display, GSM and WiFi modules. It provides a low-cost solution to monitor gas level and avoid issues with manually booking cylinders too early or late.
Autel MaxiScan MS309 User’s Manual
>> READ MORE: https://www.obdadvisor.com/autel-scanners/
Here is a detailed review of the Autel scan tool based on my own experience.
Check it out to get the REVIEW and some NOTES about using this scanner.
The P2209 trouble code indicates a problem with the nitrogen oxide (NOx) sensor in the catalytic converter. This sensor measures nitric oxide and nitrogen oxide in the exhaust. When the NOx sensor reaches its storage capacity, it triggers regeneration of the fuel management system. The code is set when the sensor's voltage reading is abnormal. Potential causes include a faulty NOx sensor, wiring issues, or a poor electrical connection. Recommended repairs include fixing exhaust leaks, replacing fuel system components, the catalytic converter, oxygen sensor, or sensors related to air and coolant monitoring. It is best to service the problem soon to prevent further damage.
Automated Unified Trolley System for LPG Leakage Detection with Safety Measur...Dr. Amarjeet Singh
The aim of this paper is to design Automated
Unified Trolley System for LPG leakage detection with safety
measures and Refill booking. This system will detect leakage
of LPG and implement security against gas leak such as it
will switch off the main power supply. It also switch on the
exhaust fan automatically to decrease the gas concentration
in air. This system will also help customer to regular update
about weight of cylinder. So they are being not cheated by gas
agency by providing less amount of gas. Also it is helpful to
know about the status of gas. If gas in the cylinder is about
threshold value, the system will immediately register gas
booking through GSM technology by sending SMS to the
distributor company and also send an alert to user at same
time. By implementing this, the LPG provider can reduce the
delivery delay time and helps to improve customer support
service in transparent manner.
This is the user manual of Autel MaxiScan MS300.
>> READ MORE: https://www.obdadvisor.com/autel-ms309-ms300-launch-creader-v/
Here is a detailed review of the scan tool based on my own experience, including:
- Compatibility
- Features and Functions
- Pros and Cons
Check it out to get the REVIEW and some NOTES about using the scanner.
Way To Use Autel Maxiscan JP701 Scanner | VtoolShopAmy joe
JP701 supports all 9 tst modes of the latest J-1979 OBD2 test specs and used for Reads Engine, Transmission, ABS & Airbag Systems for major Japanese vehicles.
How to use eu702 code reader - eu702 code reader use manual | VtoolShopAmy joe
eu702 code reader manual,The SC23 MaxiScan EU702 Code Sanner Read supports all nine OBDII test modes on all OBDII compliant vehicles to enable technicians
This document provides instructions on how to use an automotive scan tool. It describes the scan tool components and specifications. It explains how to power the scan tool, connect it to a vehicle, and navigate the user interface. It also covers diagnostic trouble codes, onboard diagnostics systems, product setup instructions, and warranty information.
The document discusses several aspects of on-board diagnostics (OBD) systems for vehicles, including:
1) The malfunction indicator lamp (MIL) is dedicated solely to indicating OBD faults and cannot be used for other purposes like maintenance alerts.
2) OBD requires monitors to detect faults on two consecutive driving cycles before setting a confirmed code and illuminating the MIL.
3) The MIL is extinguished once three driving cycles occur without fault detection or if codes are cleared via a scan tool.
4) Heavy-duty vehicles require an alternate definition of "driving cycle" due to long engine run times.
This document provides information about using a Nanocom Evolution diagnostic tool to access different models of Land Rover Defender vehicles, specifically the 2.4L and 2.2L diesel "Puma" models from 2007-2015. It details the engine control units, ABS systems, alarm systems, and available diagnostic functions for each vehicle. These include reading and clearing fault codes, viewing live engine data and sensor inputs, and accessing certain component settings. Additional resources for support documentation and forums are also listed.
The document discusses OBD II generic mode, which allows technicians to access diagnostic data from a vehicle's OBD II system without entering vehicle-specific information. It provides an overview of the types of data available in generic mode, including fuel trims, sensor voltages, temperatures, and trouble codes. While generic mode has limitations and may not provide as much data as manufacturer-specific modes, it still contains valuable information for diagnosing many emissions and drivability issues. The document also provides tips on analyzing common PID parameters to aid in diagnosis.
Similar to On board diagnostic ii obd ii (compilado) (20)
The document provides guidance on speaker placement techniques to achieve optimal sound quality. It outlines 4 methods for determining initial speaker positioning: 1) "Audio Arithmetic" which uses mathematical relationships between speaker and room boundaries, 2) "Voicing the Room" where the listener moves around speaking to find natural balance points, 3) "Changing Places" where the listener moves the speakers to their ear's position, and 4) guidelines for placing dipole speakers using a "Rule of Thirds". Precise measurement, marking, and testing of incremental position changes are recommended to refine placement. The goal is a setup that produces the best musical results.
Este documento describe un proceso de 27 pasos para completar un proyecto de construcción de una casa. Se detallan las etapas de planificación, diseño, obtención de permisos, construcción y finalización del proyecto.
PAQUETE DE SISTEMA DE VUELO DE DRON
“Para monitorear la extensión de su negocio y capturar gran cantidad de información rápidamente con muy poca o ninguna intervención del hombre;
Este documento describe los servicios de diagnóstico y escaneo profesional para vehículos, incluyendo automóviles, camiones, buses y maquinaria pesada. Se ofrecen servicios de OBD2 estándar, lectura de códigos de falla, análisis de datos, pruebas de rendimiento y diagnóstico de sistemas específicos del fabricante. Los clientes pueden acceder a información sobre el estado del motor, transmisión y otros sistemas.
The document contains technical specifications and maintenance schedules for a 1999 Mercedes-Benz CLK320, including:
- A fuse box diagram and list of fuses for the vehicle's light module.
- Scheduled maintenance items and replacement intervals for parts like spark plugs, filters, fluids, and more.
- Printouts of diagnostic tests and readings from the vehicle's onboard computer, including trouble codes, sensor data, fuel system status and more.
- Pages of images and documentation related to servicing the vehicle.
The document provides detailed reference information for maintenance and repairs of a 1999 MB CLK320.
Este documento contiene una lista de 99 canciones interpretadas por la banda argentina de rock Los Iracundos. Las canciones están agrupadas por álbumes y abarcan diversos géneros como rock, pop, tango y folclore. Algunas de las canciones más destacadas son "Baila Surfin", "Gallinita Twist", "Marianella" e "Iracundos".
Este documento es una entrevista a Juano, miembro fundador de la banda de rock uruguaya Los Iracundos. En la entrevista, Juano habla sobre los orígenes humildes de la banda en la década de 1960, cuando cada miembro tuvo que usar sus propios ahorros para comprar sus primeros instrumentos musicales. También describe cómo la banda comenzó tocando versiones de rock and roll estadounidense antes de desarrollar su propio estilo con guitarra criolla. Finalmente, Juano comparte detalles sobre el éxito
El documento describe cómo conectar la mente consciente con la mente subconsciente. Explica que entrando en un estado de trance o relajación profunda, uno puede comunicarse con el subconsciente haciéndose preguntas o pensando en cosas. Esto mejora la intuición, supera miedos, y aumenta la creatividad y acceso a recuerdos. También habla de usar afirmaciones y fe activa para impresionar al subconsciente y lograr resultados.
El documento resume los orígenes y primeros 130 años del Colegio San Calixto en Bolivia. Comenzó en 1882 con solo 13 estudiantes y 8 jesuitas, y fue fundado por el Obispo Calixto Clavijo para proveer educación católica. Sin embargo, desde el inicio enfrentó ataques de grupos anticlericales como la masonería. A lo largo de su historia, el colegio luchó contra intentos de imponer métodos seculares y quitar su autonomía, sobre todo durante gobiernos liberales a inicios del siglo
La entrevista describe la historia de Los Iracundos, una banda de rock uruguaya formada en la década de 1960. Los miembros compraron sus primeros instrumentos con sus propios ahorros y tocaban versiones de Los Teen Tops. Después de tener éxito en Uruguay y Argentina, fueron descubiertos por Palito Ortega, quien los llevó a Buenos Aires. Cambiaron su nombre a "Los Iracundos" cuando firmaron con RCA Records. Tocaron en televisión y clubs durante décadas a pesar de las dificultades polí
EL SUFRAGIO Y LA REALIDAD BOLIVIANA
UNIVERSIDAD MAYOR Y AUTONOMA TOMAS FRIAS
DEPARTAMENTO DE CULTURA
CNEL. DESP. MAX BENJAMIN SARAVIA IMAÑA
CORONEL DIPLOMADO EN ESTUDIOS SUPERIORES
LICENCIADO EN DERECHO
OTRORA COMANDANTE DE LA POLICIA BOLIVIANA
POTOSI - BOLIVIA
1963
La Unión Europea ha acordado un embargo petrolero contra Rusia en respuesta a la invasión de Ucrania. El embargo prohibirá la mayoría de las importaciones de petróleo ruso a la UE y se implementará de manera gradual durante los próximos seis meses. El embargo busca aumentar la presión económica sobre Rusia y privarla de una fuente clave de ingresos.
1. El documento proporciona numerosos consejos sobre cómo tratar a las mujeres y tener relaciones de pareja saludables, incluyendo ser respetuoso, comunicarse de manera abierta y compartir valores.
2. También recomienda mostrar interés pero no demasiado, ser seguro de sí mismo y dar espacio a la otra persona.
3. Finalmente, da consejos prácticos sobre vestimenta e higiene para atraer a las mujeres.
El documento proporciona instrucciones para reparar viviendas de adobe dañadas por sismos. Describe dos métodos: 1) Reforzar los muros con mallas de acero y mortero de cal y arena, colocando las mallas en el interior y exterior de los muros y conectándolas con alambres; y 2) Reforzar los muros con tablas de madera horizontales y verticales en el interior y exterior, uniendo las tablas horizontales con pernos de acero.
Este documento presenta la metodología de trabajo para demoler una casa de dos plantas construida con hormigón armado. La casa se demolerá para construir un edificio comercial en su lugar. La demolición se realizará principalmente de forma manual debido al tamaño y condición regular de la estructura. Se tomarán medidas de seguridad para proteger las propiedades colindantes y el público. Los escombros serán gestionados de forma adecuada.
Este plan de contingencia describe los procedimientos a seguir en caso de emergencia durante las obras de movimiento de tierras en la propiedad de los señores Ortega Limachi en Cochabamba. Establece objetivos como asegurar la atención oportuna a personas lesionadas y minimizar riesgos a trabajadores y terceros. Describe también las responsabilidades del propietario, contratista y personal, así como los métodos para evaluar y responder a contingencias como accidentes, eventos naturales, incendios o deslizamientos.
El documento evalúa la red de alcantarillado de la propiedad #8263. La red actual del vecino representa un peligro debido a su mal estado y obsolescencia. Se observan fisuras en la propiedad que podrían deberse a filtraciones de la red vecina. La red vecina debe renovarse antes de la construcción planificada en la propiedad, la cual interferirá con la ubicación actual de la red.
El resumen preliminar de la inspección estructural encontró que: (1) El suelo alrededor de la edificación no mostró anomalías. (2) La edificación no mostró daños externos importantes. (3) Se encontraron grietas leves en el interior y daños en las fachadas traseras. La estructura general fue considerada segura pero requiere reparaciones.
Este documento presenta un plan de contingencia para los trabajos de demolición de una casa de dos plantas propiedad de Hilarión Ortega y Alicia Limachi en Calacoto. El plan identifica los riesgos potenciales como sismos, tormentas e incendios y establece responsabilidades y estrategias de respuesta para emergencias. Entre las medidas se incluyen preparación para emergencias médicas, técnicas o naturales, y números de contacto de emergencia. El objetivo es mitigar cualquier accidente y brindar una respuesta rápida y adec
How to Get CNIC Information System with Paksim Ga.pptxdanishmna97
Pakdata Cf is a groundbreaking system designed to streamline and facilitate access to CNIC information. This innovative platform leverages advanced technology to provide users with efficient and secure access to their CNIC details.
Goodbye Windows 11: Make Way for Nitrux Linux 3.5.0!SOFTTECHHUB
As the digital landscape continually evolves, operating systems play a critical role in shaping user experiences and productivity. The launch of Nitrux Linux 3.5.0 marks a significant milestone, offering a robust alternative to traditional systems such as Windows 11. This article delves into the essence of Nitrux Linux 3.5.0, exploring its unique features, advantages, and how it stands as a compelling choice for both casual users and tech enthusiasts.
Enchancing adoption of Open Source Libraries. A case study on Albumentations.AIVladimir Iglovikov, Ph.D.
Presented by Vladimir Iglovikov:
- https://www.linkedin.com/in/iglovikov/
- https://x.com/viglovikov
- https://www.instagram.com/ternaus/
This presentation delves into the journey of Albumentations.ai, a highly successful open-source library for data augmentation.
Created out of a necessity for superior performance in Kaggle competitions, Albumentations has grown to become a widely used tool among data scientists and machine learning practitioners.
This case study covers various aspects, including:
People: The contributors and community that have supported Albumentations.
Metrics: The success indicators such as downloads, daily active users, GitHub stars, and financial contributions.
Challenges: The hurdles in monetizing open-source projects and measuring user engagement.
Development Practices: Best practices for creating, maintaining, and scaling open-source libraries, including code hygiene, CI/CD, and fast iteration.
Community Building: Strategies for making adoption easy, iterating quickly, and fostering a vibrant, engaged community.
Marketing: Both online and offline marketing tactics, focusing on real, impactful interactions and collaborations.
Mental Health: Maintaining balance and not feeling pressured by user demands.
Key insights include the importance of automation, making the adoption process seamless, and leveraging offline interactions for marketing. The presentation also emphasizes the need for continuous small improvements and building a friendly, inclusive community that contributes to the project's growth.
Vladimir Iglovikov brings his extensive experience as a Kaggle Grandmaster, ex-Staff ML Engineer at Lyft, sharing valuable lessons and practical advice for anyone looking to enhance the adoption of their open-source projects.
Explore more about Albumentations and join the community at:
GitHub: https://github.com/albumentations-team/albumentations
Website: https://albumentations.ai/
LinkedIn: https://www.linkedin.com/company/100504475
Twitter: https://x.com/albumentations
Full-RAG: A modern architecture for hyper-personalizationZilliz
Mike Del Balso, CEO & Co-Founder at Tecton, presents "Full RAG," a novel approach to AI recommendation systems, aiming to push beyond the limitations of traditional models through a deep integration of contextual insights and real-time data, leveraging the Retrieval-Augmented Generation architecture. This talk will outline Full RAG's potential to significantly enhance personalization, address engineering challenges such as data management and model training, and introduce data enrichment with reranking as a key solution. Attendees will gain crucial insights into the importance of hyperpersonalization in AI, the capabilities of Full RAG for advanced personalization, and strategies for managing complex data integrations for deploying cutting-edge AI solutions.
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdfMalak Abu Hammad
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
GraphSummit Singapore | The Art of the Possible with Graph - Q2 2024Neo4j
Neha Bajwa, Vice President of Product Marketing, Neo4j
Join us as we explore breakthrough innovations enabled by interconnected data and AI. Discover firsthand how organizations use relationships in data to uncover contextual insights and solve our most pressing challenges – from optimizing supply chains, detecting fraud, and improving customer experiences to accelerating drug discoveries.
Maruthi Prithivirajan, Head of ASEAN & IN Solution Architecture, Neo4j
Get an inside look at the latest Neo4j innovations that enable relationship-driven intelligence at scale. Learn more about the newest cloud integrations and product enhancements that make Neo4j an essential choice for developers building apps with interconnected data and generative AI.
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdfPaige Cruz
Monitoring and observability aren’t traditionally found in software curriculums and many of us cobble this knowledge together from whatever vendor or ecosystem we were first introduced to and whatever is a part of your current company’s observability stack.
While the dev and ops silo continues to crumble….many organizations still relegate monitoring & observability as the purview of ops, infra and SRE teams. This is a mistake - achieving a highly observable system requires collaboration up and down the stack.
I, a former op, would like to extend an invitation to all application developers to join the observability party will share these foundational concepts to build on:
Dr. Sean Tan, Head of Data Science, Changi Airport Group
Discover how Changi Airport Group (CAG) leverages graph technologies and generative AI to revolutionize their search capabilities. This session delves into the unique search needs of CAG’s diverse passengers and customers, showcasing how graph data structures enhance the accuracy and relevance of AI-generated search results, mitigating the risk of “hallucinations” and improving the overall customer journey.
Climate Impact of Software Testing at Nordic Testing DaysKari Kakkonen
My slides at Nordic Testing Days 6.6.2024
Climate impact / sustainability of software testing discussed on the talk. ICT and testing must carry their part of global responsibility to help with the climat warming. We can minimize the carbon footprint but we can also have a carbon handprint, a positive impact on the climate. Quality characteristics can be added with sustainability, and then measured continuously. Test environments can be used less, and in smaller scale and on demand. Test techniques can be used in optimizing or minimizing number of tests. Test automation can be used to speed up testing.
Building RAG with self-deployed Milvus vector database and Snowpark Container...Zilliz
This talk will give hands-on advice on building RAG applications with an open-source Milvus database deployed as a docker container. We will also introduce the integration of Milvus with Snowpark Container Services.
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slackshyamraj55
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...Zilliz
Join us to introduce Milvus Lite, a vector database that can run on notebooks and laptops, share the same API with Milvus, and integrate with every popular GenAI framework. This webinar is perfect for developers seeking easy-to-use, well-integrated vector databases for their GenAI apps.
Pushing the limits of ePRTC: 100ns holdover for 100 daysAdtran
At WSTS 2024, Alon Stern explored the topic of parametric holdover and explained how recent research findings can be implemented in real-world PNT networks to achieve 100 nanoseconds of accuracy for up to 100 days.
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...Neo4j
Leonard Jayamohan, Partner & Generative AI Lead, Deloitte
This keynote will reveal how Deloitte leverages Neo4j’s graph power for groundbreaking digital twin solutions, achieving a staggering 100x performance boost. Discover the essential role knowledge graphs play in successful generative AI implementations. Plus, get an exclusive look at an innovative Neo4j + Generative AI solution Deloitte is developing in-house.
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...
On board diagnostic ii obd ii (compilado)
1. 1
This document is intended to help in the understanding of OBDII parameters, known as
‘PIDs’, and give them definition. It is intended to be only a basic, not a technical guide to
scantool data. These PIDS are used by the OBDII system and by scantools that interact
with the systems for diagnostics and system interrogation. PID stands for Parameter
Identification, and in practice is rather cryptic. The scantool, luckily, takes this cryptic, bit
and byte data shorthand and translates it for us, so it is more understandable.
Live Data Trigger Frame
PID Unit Frame
These are parameters specific to the scantool being used in this case, and are
not OBDII standard PIDs.
Fuel System 1 Status [Status 1 or Fuelsys1]
Fuel System 2 Status [Status 2 or Fuelsys2]
Returns either OL – for Open Loop, or CL – for Closed Loop
Tells whether fueling is currently based on O2 Sensors and the oxygen content
of the exhaust, [Closed Loop] or based on sensor inputs [Open Loop] due to
conditions; logged faults, cold engine or wide open throttle, for instance.
Calculated Load Value [CLV or Load_PCT]
Engine load is represented by a "Calculated load value" which refers to an
indication of the current airflow divided by peak airflow, where peak airflow is
corrected for altitude, if available. This definition provides a unitless number that
is not engine specific, and provides the system with an indication of the percent
engine capacity that is being used. (With wide open throttle as 100%).
Engine Coolant Temp [ECT]
Current engine coolant temp as measured by the ECT [Engine Coolant Temp
sensor]. Usually reported in Celsius degrees.
Short Term Fuel Trim-Bank 1 [STFT 1 or SHRTFT1]
Short Term Fuel Trim-Bank 2 [STFT 2 or SHRTFT2]
Immediate trim changes made to the fuel mapping in response to oxygen
changes in the exhaust. Base fueling [injection] map is contained in the ECM, if
changes are required, fuel is added or subtracted from the base. Shown in
percent, positive percentage is ADDING fuel, negative percentage is
SUBTRACTING fuel. Short term trims are lost at key off.
Long Term Fuel Trim- Bank 1 [LTFT 1 or LONGFT1]
Long Term Fuel Trim- Bank 2 [LTFT 2 or LONGFT2]
Long term changes made to the fuel mapping based on Short Term fueling
corrections. Example: Short Term remaining at plus 6% for an extended period;
Long Term Trim will increment by that percentage and Short Term will return to
zero. Long Term Trims are maintained in non-volatile memory at key off, and
therefore not lost.
Page 1
2. 2
Engine RPM [RPM]
I think this one is self explanatory.
Vehicle Speed Sensor [VSS]
Returns current vehicle speed, usually shown in kph, but some scantools allow
selecting kilometers or miles per hour.
Ignition Timing Advance #1 [Sparkadv]
Shows current spark timing advance in degrees for cylinder #1. Most engines
with knock retard systems can retard timing for individual cylinders, however.
Intake Air Temp [IAT]
Returns current temperature of the air entering the induction system. Like ECT,
usually reported in degrees Celsius, but some tools allow selecting scale.
Air Flow Rate from Mass Air Flow Sensor [MAF]
Returns the ECM calculation of total air flow, based on MAF signal AND air
temperature [IAT]. Most systems list this in grams per second, g/sec.
Absolute Throttle Position [TP or ABS_TP]
Listed in percent, shows actual position of the throttle butterfly, as it is not directly
connected to any cable or other driver input.
Bank 1 -- Sensor 2 Volts [O2S12]
Bank 2 – Sensor 2 Volts [O2S22]
Voltage output of downstream [second] Exhaust Oxygen sensor. Varies between
.2v and .8v normally. Used mainly for monitoring exhaust catalyst function.
Bank 1 – Sensor 2 % [O2S12STFT]
Bank 2 – Sensor 2 % [O2S22STFT]
Returns an additional trim value to the ECM for extremely fine fueling corrections.
Not used except for later model years, 2006 and later. Generally not useful to the
novice.
OBD Requirements OBD and OBD2 [OBDSUP]
Returns information to define which OBD requirements the vehicle was designed
to meet; i.e. which OBD system is onboard.
01h : OBD II (California ARB) 08h : EOBD and OBD
02h : OBD (Federal EPA) 09h : EOBD, OBD and OBD II
03h : OBD and OBD II 0Ah : JOBD
04h : OBD I 0Bh : JOBD and OBD
05h : not intended to meet any requirements 0Ch : JOBD and EOBD
06h : EOBD (Europe) 0Dh : JOBD, EOBD, and OBD II
07h : EOBD and OBD II 0Eh-FFh : Reserved by SAE J1979
Page 2
4. OBDII and Emissions Testing Pg 1 of 1 http://www.obdii.com
OBDII and Emissions Testing
Are you up to speed on OBD II? You should be because starting in 2002, a number of states have announced
plans to change their emissions testing programs over to OBD II.
Instead of doing a tailpipe emissions check on a dynamometer, an OBD II check is a simple plug-in test that
takes only seconds. What’s more, OBD II will detect emissions problems that might not cause a vehicle to fail a
tailpipe test - which means emissions test failures under the OBD II test programs are expected to be
significantly higher.
The second-generation self-diagnostic emissions software has been required on all new vehicles sold in this
country since model year 1996, including all imports. OBD II is a powerful diagnostic tool that can give you
insight into what’s actually happening within the engine control system.
Unlike earlier OBD systems that set a DTC when a sensor circuit shorts, opens or reads out of range, OBD II is
primarily emissions-driven and will set codes anytime a vehicle’s emissions exceed the federal limit by 1.5
times.It also will set codes if there is a gross sensor failure, but some types of sensor problems won’t always
trigger a code. Consequently, the Check Engine light on an OBD II-equipped vehicle may come on when there
is no apparent driveability problem, or it may not come on even though a vehicle is experiencing a noticeable
driveability problem.
The determining factor as to whether or not the Check Engine light comes on is usually the problem’s effect on
emissions. In many instances, emissions can be held in check, despite a faulty sensor, by adjusting fuel trim. So
as long as emissions can be kept below the limit, the OBD II system may have no reason to turn on the light.
CHECK ENGINE LIGHT
The "Malfunction Indicator Lamp" (MIL), which may be labeled "Check Engine" or "Service Engine Soon" or a
symbol of an engine with the word "Check" in the middle, is supposed to alert the driver when a problem occurs.
Depending on how the system is configured and the nature of the problem, the lamp may come on and go off,
remain on continuously or flash - all of which can be very confusing to the motorist because he has no way of
knowing what the light means. Is it a serious problem or not? If the engine seems to be running okay, the
motorist may simply ignore the light. With OBD II, the Check Engine light will come on only for emissions-related
failures. A separate warning light must be used for other non-emissions problems such as low oil pressure,
charging system problems, etc.
If the light is on because of a misfire or a fuel delivery problem, and the problem does not recur after three drive
cycles (under the same driving conditions), the Check Engine light may go out. Though you might think the
vehicle has somehow healed itself, the intermittent problem may still be there waiting to trigger the light once
again when conditions are right. Whether the light goes out or remains on, a code will be set and remain in the
computer’s memory to help you diagnose the fault.
With some exceptions, the OBD II warning lamp will also go out if a problem does not recur after 40 drive
cycles. A drive cycle means starting a cold engine and driving it long enough to reach operating temperature.
The diagnostic codes that are required by law on all OBD II systems are "generic" in the sense that all vehicle
manufacturers use the same common code list and the same 16-pin diagnostic connector. Thus, a P0302
misfire code on a Nissan means the same thing on a Honda, Toyota or Mercedes-Benz. But each vehicle
manufacturer also has the freedom to add their own "enhanced" codes to provide even more detailed
information about various faults.
Enhanced codes also cover non-emission related failures that occur outside the engine control system. These
include ABS codes, HVAC codes, air bag codes and other body and electrical codes.
Page 4
5. OBDII and Emissions Testing Pg 2 of 2 http://www.obdii.com
The second character in an OBD II will be a zero if it’s a generic code, or a "1" if it’s a dealer enhanced code
(specific to that particular vehicle application).
The third character in the code identifies the system where the fault occurred. Numbers 1 and 2 are for fuel or
air metering problems, 3 is for ignition problems or engine misfire, 4 is for auxiliary emission controls, 5 relates
to idle speed control problems, 6 is for computer or output circuit faults, and 7 and 8 relate to transmission
problems.
Codes can be accessed and cleared using an OBDII scan tool such as AutoTap.
MISFIRE DETECTION
If an emissions problem is being caused by engine misfire, the OBD II light will flash as the misfire is occurring.
But the light will not come on the first time a misfire problem is detected. It will come on only if the misfire
continues during a second drive cycle and will set a P0300 series code.
A P0300 code would indicate a random misfire (probably due to a vacuum leak, open EGR valve, etc.). If the
last digit is a number other than zero, it corresponds to the cylinder number that is misfiring. A P0302 code, for
example, would tell you cylinder number two is misfiring. Causes here would be anything that might affect only a
single cylinder such as a fouled spark plug, a bad coil in a coil-on-plug ignition system or distributorless ignition
system with individual coils, a clogged or dead fuel injector, a leaky valve or head gasket.
The OBD II system detects a misfire on most vehicles by monitoring variations in the speed of the crankshaft
through the crankshaft position sensor. A single misfire will cause a subtle change in the speed of the crank.
OBD II tracks each and every misfire, counting them up and averaging them over time to determine if the rate of
misfire is abnormal and high enough to cause the vehicle to exceed the federal emissions limit. If this happens
on two consecutive trips, the Check Engine light will come on and flash to alert the driver when the misfire
problem is occurring.
Misfire detection is a continuous monitor, meaning it is active any time the engine is running. So too is the fuel
system monitor that detects problems in fuel delivery and the air/fuel mixture, and something called the
"comprehensive monitor" that looks for gross faults in the sensors and engine control systems. These monitors
are always ready and do not require any special operating conditions.
Other OBD II monitors are only active during certain times. These are the "non-continuous" monitors and include
the catalytic converter efficiency monitor, the evaporative system monitor that detects fuel vapor leaks in the fuel
system, the EGR system monitors, the secondary air system monitor (if the vehicle has such a system), and the
oxygen sensor monitors.On some 2000 and newer vehicles, OBD II also has a thermostat monitor to keep an
eye on the operation of this key component. The thermostat monitor will be required on all vehicles by 2002. On
some 2002 model-year vehicles, there also is a new PCV system monitor, which will be required on all vehicles
by 2004.
The catalytic converter monitor keeps an eye on converter efficiency by comparing the outputs from the
upstream and downstream oxygen sensors. If the converter is doing its job, there should be little unburned
oxygen left in the exhaust as it exits the converter. This should cause the downstream O2 sensor to flatline at a
relatively fixed voltage level near maximum output.
If the downstream O2 sensor reading is fluctuating from high to low like the front sensor, it means the converter
is not functioning.The Check Engine light will come on if the difference in O2 sensor readings indicates
hydrocarbon (HC) readings have increased to a level that is 1.5 times the federal limit. For 1996 and newer
vehicles that meet federal Low Emission Vehicles (LEV) requirements, the limit allows only 0.225 grams per
mile (gpm) of HC - which is almost nothing. Converter efficiency drops from 99 percent when it is new to around
96 percent after a few thousand miles. After that, any further drop in efficiency may be enough to turn on the
Check Engine light. We’re talking about a very sensitive diagnostic monitor.
Page 5
6. OBDII and Emissions Testing Pg 3 of 3 http://www.obdii.com
The EVAP system monitor checks for fuel vapor leaks by performing either a pressure or vacuum test on the
fuel system. For 1996 through 1999 vehicles, the federal standard allows leaks up to the equivalent of a hole
.040 inches in diameter in a fuel vapor hose or filler cap. For 2000 and newer vehicles, the leakage rate has
been reduced to the equivalent of a .020 in. diameter hole, which is almost invisible to the naked eye but can be
detected by the OBD II system. Finding these kinds of leaks can be very challenging.
READINESS FLAGS
An essential part of the OBD II system are the "readiness flags" that indicate when a particular monitor is active
and has taken a look at the system it is supposed to keep watch over. The misfire detection, fuel system and
continuous system monitors are active and ready all the time, but the non-continuous monitors require a certain
series of operating conditions before they will set - and you can’t do a complete OBD II test unless all of the
monitors are ready.
To set the converter monitor, for example, the vehicle may have to be driven a certain distance at a variety of
different speeds. The requirements for the various monitors can vary considerably from one vehicle
manufacturer to another, so there is no "universal" drive cycle that will guarantee all the monitors will be set and
ready.
As a general rule, doing some stop-and-go driving around town at speeds up to about 30 mph followed by five to
seven minutes of 55 mph plus highway speed driving will usually set most or all of the monitors (the converter
and EVAP system readiness monitors are the hardest ones to set). So if you’re checking the OBD II system and
find a particular monitor is not ready, it may be necessary to test drive the vehicle to set all the monitors.
The Environmental Protection Agency (EPA) realized this shortcoming in current generation OBD II systems.
So, when it created the rules for states that want to implement OBD II testing in place of tailpipe dyno testing, it
allows up to two readiness flags to not be set prior to taking an OBD II test on 1996 to 2000 vehicles, and one
readiness flag not to be set on 2001 and newer vehicles. You can use the AutoTap OBDII scantool to check that
your readiness flags are set before having your vehicle emissions-tested. This can save you the aggrevation of
being sent off to drive around and come back later.
Some import vehicles have known readiness issues. Many 1996-’98 Mitsubishi vehicles will have monitors that
read "not ready" because setting the monitors requires very specific drive cycles (which can be found in their
service information). Even so, these vehicles can be scanned for codes and the MIL light without regard to
readiness status.On 1996 Subarus, turning the key off will clear all the readiness flags. The same thing happens
on 1996 Volvo 850 Turbos. This means the vehicle has to be driven to reset all the readiness flags. On 1997
Toyota Tercel and Paseo models, the readiness flag for the EVAP monitor will never set, and no dealer fix is yet
available. Other vehicles that often have a "not ready" condition for the EVAP and catalytic converter monitors
include 1996-’98 Volvos, 1996-’98 Saabs, and 1996-’97 Nissan 2.0L 200SX models.
OBD II TEST
An official OBD II emissions test consists of three parts:
1. An inspector checks to see if the MIL light comes on when the key is turned on. If the light does not
come on, the vehicle fails the bulb check.
2. A scanner similar to AutoTap is plugged into the diagnostic link connector (DLC), and the system is
checked for monitor readiness. If more than the allowed number of monitors are not ready, the vehicle is
rejected and asked to come back later after it has been driven sufficiently to set the readiness flags. The
scanner also checks the status of the MIL light (is it on or off?), and downloads any fault codes that may
be present.If the MIL light is on and there are any OBD II codes present, the vehicle fails the test and
must be repaired. The vehicle also fails if the DLC is missing, has been tampered with or fails to provide
any data.
3. As a final system check, the scanner is used to command the MIL lamp on to verify it is taking
commands from the onboard computer. If the OBD II light is on, or a vehicle has failed an OBD II
Page 6
7. OBDII and Emissions Testing Pg 4 of 4 http://www.obdii.com
emissions test, your first job is to verify the problem. That means plugging into the OBD II system,
pulling out any stored codes and looking at any system data that might help you nail down what’s
causing the problem. Long-term fuel trim data can provide some useful insight into what’s going on with
the fuel mixture. If long-term fuel trim is at maximum, or you see a big difference in the numbers for the
right and left banks of a V6 or V8 engine, it would tell you the engine control system is trying to
compensate for a fuel mixture problem (possibly an air leak, dirty injectors, leaky EGR valve, etc.).
OBD II also provides "snap shot" or "freeze frame" data, which can help you identify and diagnose intermittent
problems. When a fault occurs, OBD II logs a code and records all related sensor values at that moment for
later analysis.
Once you’ve pinpointed the problem and hopefully replaced the faulty component, the final step is to verify that
the repair solved the problem and that the OBD II light remains off. This will usually require a short test drive to
reset all the readiness monitors and run the OBD II diagnostic checks.
OBD II TOOLS & EQUIPMENT
You can’t work on OBD II systems without some type of OBD II-compliant scanner. The AutoTap OBDII Scan
Tool is available in both PC/laptop versions and Palm PDA versions. The computing power and display of a PC
or Palm gives AutoTap a much broader range of features than the older style hand-held scantools.
The OBDII Home Page
http://www.obdii.com
Page 7
8. Gary Stamberger – Training Director
Car-Sound/Magnaflow Performance Exhaust
This month we take the discussion of Oxygen Sensors to yet another level. In recent discussions we talked about the role these sensors played in
closed loop fuel control. What exactly does that mean, “Closed loop fuel control”, and what role does it play in maintaining a good working
converter?
When a vehicle is started cold there is a warm up period which is referred to as, “Open loop”. It’s during this time period that the engine is polluting
the most. Consequently, getting to closed loop fuel control is a top priority. The PCM has an internal clock that restarts on each start-up and it knows,
based mainly on temperature, how long before all components are operating and it is ready to enter closed loop. To this end, many elements have been
added to the systems. Oxygen sensors have built in heaters to speed the warm up process. The PCM can detect when the engine is taking too long to
come up to temperature and will set a code P0125, “Insufficient temperature for closed loop fuel control” which typically means the thermostat is
stuck open.
Once the conditions are met and the PCM gains fuel control the goal then becomes maintaining it. The oxygen sensor is referred to as a, “Voltage
Generator” and reports the content of oxygen in the exhaust stream to the PCM ranging between 100mv (Millivolts) and 900mv. When the oxygen
content is high, (Voltage is low, near 100mv) the PCM sees this as a lean condition and its response is to add fuel. When the sensor reports back that
there is little oxygen in the exhaust stream (high voltage, near 900mv), a rich condition is sensed and the PCM pulls fuel away. A technician can
monitor this data on a scan tool as, “Short Term Fuel Trim” or STFT. A positive percentage indicates the computer is adding fuel while a negative
number says it is taking fuel away. If the PCM is in fuel control, monitoring the direct relationship between O2 and STFT scan data will confirm it.
The next step then is to look at Long Term Fuel Trim (LTFT) percentages. These numbers give us a history of what the PCM has been doing with fuel
trim over the long haul. As with STFT, positive percentages tell us the tendency is to be adding fuel (compensating for a lean condition) while
negative numbers indicate the PCM is pulling fuel back, (Overcoming a rich condition). If either of these conditions exists for a prolonged period of
time and the LTFT percentages exceed the PCM’s parameters a fuel trim code will set (P0170-P0175) and Check Engine light illuminated. The
example below shows us that although the PCM appears to be in fuel control there is evidence that it has been adding fuel over time.
Our concern when looking at fuel trim is what it may be telling us about engine efficiency and whether the computer has been compensating for other
fuel related problems. If the engine has been over-fueling the question is…WHY? A leaking fuel injector, fuel pressure regulator, lazy O2, or bad
Mass Air Flow (MAF) would be some of the considerations. The same issue exists if it’s too lean. Here an air leak, clogged injectors or fuel filter, or
miscalculated air flow could be the cause. Any Fuel Trim condition that persists will eventually take its toll on the catalytic converter and must be
addressed by the repair technician before installing a new one.
Cleaning up the environment…one converter at a time
Gary
INTERPRETING FUEL TRIM DATA
Bulletin TB-80010
May, 2009
Page 8
9. Gary Stamberger – Training Director
Magnaflow Exhaust Products
In the first part of this OBD II Code Diagnosis series I stated that we would discuss the principles of OBD II codes and
breakdown each character that defines them. For a generic discussion of OBD I’ll refer you to TB-80016 and 80017. We archive all
of our bulletins and they can be found on our website at www.maganaflow.com. Look for Tech Bulletins under Tech Support. For
this series I would like to stay on a more specific path.
In our first two parts we took a very common Ford EGR code and broke down the diagnosis. I chose this code not only for its
commonality but also because this EGR system uses several components, each one playing a major role in the vehicles ability to
reduce NOx. Although the PCM has the ability to set several different and distinct codes for each component (9 generic and 10
specific) the interrelation of the components cannot be ignored. As we saw in our example, one of the possible causes for the P0401
code was mechanical and had nothing to do with the malfunction of any one component.
Another common issue in Code Diagnostics sometimes overlooked is that of retrieving codes in both OBD II Generic and Enhanced
or Manufacture Specific mode. Depending on the tool being used, the enhanced option may not be available (i.e. Code Reader only).
Using generic mode requires less input therefore is faster and in most cases will get the technician to where he wants to be. The
downside is that it is a generic code and therefore in many cases the repair information will not be specific to that vehicle.
The obvious upside then to using Enhanced Mode, is that the diagnostic information will be specific to that vehicle or at least that
manufacturer. The description and operation will give you a better idea of what the PCM is looking for and the subsequent testing
should lead you to the proper diagnosis the first time.
Example: 2005 Altima, 2.5L with an illuminated MIL. The OBD II code was P0140, O2 Circuit B1S2 No Activity Detected. A quick
glance at the data stream showed that under the proper test conditions the sensor displayed activity. At this point we might determine
that it is an intermittent problem, clear the code and send the customer on their way. However a look at Enhanced codes revealed a
P1147, O2 B1S2 Maximum Voltage not Obtained. A closer look at data stream showed that the sensor was not reaching a specific
maximum voltage of .78v. This specific information was not available when processing the P0140 code.
The key to any diagnostic situation is to always follow a pattern for each problem we face and code diagnostics is no different. Yes…
each manufacture has common problems and knowing where to find that information is valuable but sometimes even the “silver
bullet” can be a dud! Whether it is a no start, misfire, won’t idle, MIL illuminated or any number of issues, having a plan is by far the
best plan. “Shot Gun” diagnosis will on occasion allow us to hit the illusive homerun but more often than not we spend a whole day
repairing a component only to go home with that empty feeling in our stomachs, knowing the same problem will reoccur in the
morning.
Diagnostics is an art and getting good at it can be a great confidence booster, however these vehicles are changing constantly and
there is no time to rest. As I say when closing all my classes:
THE RULES ARE ALWAYS CHANGING
TECHNOLOGY KEEPS MOVING FORWARD
EDUCATION IS A CONTINUAL PROCESS
Cleaning up the environment…one converter at a time
Gary
OBD II Code Diagnosis Part III
Bulletin TB-80035
September, 2011
Page 9
10. ScanMaster-ELM
What is OBD-II?
OBD-II stands for On-Board Diagnostics second (II) generation, a computer-based system
built into all model year (MY) 1996 in USA and newer light-duty cars and trucks. OBD-II
monitors the performance of some of the engines' major components, including individual
emission controls. The system provides owners with an early warning of malfunctions by way
of a dashboard "Check Engine" light (also known as a Malfunction Indicator Light or MIL, for
short). By giving vehicle owners this early warning, OBD-II protects not only the
environment but also consumers, identifying minor problems before they become major
repair bills.
EOBD - European On-Board Diagnostic
EOBD is a standard that is issued by the European Community. The main goal with the
standard is to give the authorities a tool to control the exhaust emission from vehicles. The
EOBD standard has been implemented in petrol cars throughout the European Union from
01.01.2001 (EU directive 98/96/EC). For LPG and Diesel vehicles the implementation of
applicable regulations is scheduled to take place before 2005. The EOBD standard includes
five different communication protocols: ISO 9141-2, ISO 14230-4(KWP2000), SAE J1850
VPW, SAE J1850 PWM and ISO 15765-4 CAN.
If the car supports EOBD you have the possibilities to read out stored information from the
ECU in the car, including:
€ Read fault codes
€ Erase fault codes
€ Read freeze frame data
€ Get real-time data (displayed as numbers or graphs)
€ Get monitoring results from oxygen sensors
€ Get result from readiness test
To read out the information you require an OBD-II/EOBD diagnostic tool such as the
ScanMaster software together with an approbiate interface for the connection between the
cars diagnostic connector and the computer or notbook.
How do I know the OBD system is working correctly?
When you turn on the ignition, the "Service Engine Soon" or "Check Engine" light should
flash briefly, indicating that the OBD system is ready to scan your vehicle for any
malfunctions. After this brief flash, the light should stay off while you drive as long as no
problems are detected. If so, you'll be glad to know that your vehicle is equipped with an
early warning system that could save you time, money, and fuel in addition to helping
protect the environment!
www.wgsoft.de
- 5 -
Page 10
11. ScanMaster-ELM
Which OBD-II protocol is supported by vehicle?
All cars and light trucks built for sale in the United States after 1996 are required to be OBD-
II compliant. The European Union adopted a similar law in 2000 for gasoline-powered
vehicles, and in 2003 for cars with diesel engines.
An OBD-II compliant vehicle can use any of the five communication protocols: J1850 PWM
and VPW, ISO9141, ISO14230 (also known as Keyword Protocol 2000), and more recently,
CAN (ISO15765/SAE J2480). Car manufacturers were not allowed to use CAN until model
year 2003.
As a general rule, you can determine which protocol your vehicle is using by looking at the
pinout of the DLC:
The following table explains how to determine the protocol:
Pin 2 Pin 6 Pin 7 Pin 10 Pin 14 Pin 15* Standard
J1850
Bus+
CAN High
ISO 9141-2
K Line and
ISO/DIS
14230-4
J1850 Bus CAN Low
ISO 9141-2
L Line and
ISO/DIS
14230-4
must have - - must have - - J1850 PWM
must have - - - - - J1850 VPW
- - must have - - may have ISO9141/14230
- must have - - must have - CAN
The connector should have: Pin 4 - Chassis Ground, Pin 5 - Signal Ground, Pin 16 - Battery
power
www.wgsoft.de
- 6 -
Page 11
12. ScanMaster-ELM
This means that:
Protocol The connector must have pins
PWM 2, 4 and/or 5, 10, and 16
VPW 2, 4 and/or 5, and 16, but not 10.
ISO 4 and/or 5, 7, and 16. Pin 15 *may or may not be present.
CAN 4 and/or 5, 6, 14 and 16
*For ISO communications, pin 15 (L-line) is not always required. Pin 15 was used on earlier
ISO/KWP2000 cars to "wake-up" the ECU before communication could begin on pin 7 (K-
Line). Later cars tend to communicate using only pin 7 (K-Line).
Because of the different protocol a car might have it is recommended to use an interface
which supports all protocols as all modern interfaces do.
www.wgsoft.de
- 7 -
Page 12
13. ScanMaster-ELM
Diagnostic Link Connector (DLC) Mapping Diagram Explanation
The mapping diagram of DLC locations contains a divided instrument panel (IP) with
numbered areas. Each numbered area represents specific sections of the IP where
manufacturers may have located DLCs. This document briefly clarifies the numbered
locations on the mapping diagram. We will use this mapping diagram to catalog
manufacturer responses to the recent 208 letter requesting OBD DLC locations for 96MY and
future vehicles. Areas 1-3 fall within the preferred DLC location while the remaining areas, 4-
8, fall into the allowable DLC location according to EPA requirements. Areas 4-8 require that
manufacturers label the vehicle in the preferred location to notify parties of the alternate
connector location.
Preferred Location(s)
Location #1: This location represents a DLC positioned on the underside of the IP directly
under the steering column (or approximately 150mm left or right of the steering column).
Visualizing the underside of an IP divided into three equal parts from inside the passenger
compartment, this represents the center section.
Location #2: This location represents a DLC positioned on the underside of the IP between
the steering column and the drivers side passenger door. Visualizing the underside of an IP
divided into three equal parts from inside the passenger compartment, this represents the
left section.
Location #3: This location represents a DLC positioned on the underside of the IP between
the steering column and the center console. Visualizing the underside of an IP divided into
three equal parts from inside the passenger compartment, this represents the right section.
www.wgsoft.de
- 8 -
Page 13
14. ScanMaster-ELM
Allowable Location(s)
Location #4: This location represents a DLC positioned on the upper part of the IP between
the steering column and the center console (but not on the center console, see location #6).
Location #5: This location represents a DLC positioned on the upper part of the IP between
the steering column and the driver side, passenger door.
Location #6: This location represents a DLC positioned on the vertical section of the center
console and left of the vehicle center line.
Location #7: This location represents a DLC positioned 300 mm right of the vehicle
centerline either on the vertical section of the center console or on the passenger side of the
vehicle.
Location #8: This location represents a DLC positioned on the horizontal section of the
center console either left or right of the vehicle center line. This does not include the
horizontal section of the center console that extends into the rear passenger area (see
location #9).
Location #9: This location, not shown, represents any DLC positioned in an area other than
those mentioned above (e.g., in the rear passenger area on the driver side armrest).
www.wgsoft.de
- 9 -
Page 14
15. ScanMaster-ELM
OBD-II Diagnostic Protocol
The diagnostic protocol for OBD-II is SAE J1979. A diagnostic request or response message
has a maximum of seven data bytes. The first byte following the header is the test mode. It
is also called the service identifier (SID or PID). The following bytes vary depending on the
specific test mode.
There are nine diagnostic test modes:
Mode $01 – Request Current Powertrain Diagnostic Data - This service gives access
to current emission-related data values, including analogue inputs and outputs, digital inputs
and outputs and system status information.
Mode $02 – Request Powertrain Freeze Frame Data - This service gives access to
current emission-related data values in a freeze frame. A freeze frame consists of data
values stored at a specific event; such as an engine malfunction of some kind.
Mode $03 – Request Emission-Related Powertrain Diagnostic Trouble Codes - The
purpose of this service is to enable the external test equipment to obtain “confirmed”
emission-related DTCs.
Mode $04 – Clear/Reset Emission-Related Diagnostic Information - The purpose of
this service is to provide a means for the external test equipment to command ECUs to clear
all emission-related diagnostic information. This includes:
€ Number of diagnostic trouble codes
€ Diagnostic trouble codes
€ Trouble codes for Freeze Frame data
€ Freeze Frame data
€ O2 test data
€ Status of system monitor tests
€ On-board monitor test results
€ Travelled distance with activated MIL
€ Number of warm startups since DTC clear
€ Travelled distance since DTC clear
€ Engine runtime (minutes) with MIL activated
€ Time since DTC clear
€ as well as learned adaptive values of the injection system.
Other manufacturer specific clear/reset actions might be possible.
Mode $05 – Request Oxygen Sensor Monitoring Test Results - The purpose of this
service is to allow access to the on-board oxygen sensors monitoring test results.
Mode $06 – Request On-Board Monitoring Test Results for Non- Continuously
Monitored Systems - This service gives access to the results for on-board diagnostic
monitoring tests of specific components/systems that are not continuously monitored.
Examples of this are catalyst monitoring and the evaporative system monitoring.
www.wgsoft.de
- 10 -
Page 15
16. ScanMaster-ELM
Mode $07 – Request On-Board Monitoring Test Results for Continuously
Monitored Systems - Through this service, the external test equipment, can obtain test
results for emission-related Powertrain components/systems that are continuously monitored
during normal driving conditions.
Mode $08 – Request Control of On-Board System, Test or Component - This service
enables external test equipment to control the operation of an on-board system, test or
component.
Mode $09 – Request Vehicle Information - This service gives access to vehicle specific
vehicle information such as Vehicle Identification Number (VIN) and Calibration IDs.
www.wgsoft.de
- 11 -
Page 16
17. Reading Performance Information Data (PID)
Posted by Alex (Im) E. on 01 February 2013 12:11 AM
PIDS are the serial data that can be accessed from the vehicle computer using a scan tool. PIDS include:
Status of the OBD II System Component Monitors
(Ready or Complete, or Not Ready or Incomplete)
Live Sensor Data
(Oxygen sensor rich/lean indication, coolant temperature, MAP value, TPS value, vehicle speed, mass
air flow, ambient temperature, engine rpm, etc.)
Status of Switches or Devices
(cruise control on/off. brake pedal switch on/off. TCC engaged/disengaged, etc.)
Long and Short Term Fuel Trim, O2 sensor cross counts, injector duration.
DIAGNOSTIC VALUE
PIDS provide valuable diagnostic information when checking the operation or status of various sensors, circuits
and switches in the vehicle's engine management system.
For example, if the MIL lamp is on and you find an oxygen sensor code, you can call up the oxygen sensor
PIDS on your scan tool display to see what the oxygen sensor is telling the PCM.
You can also compare PIDS to see how one component may be affecting another.
For example, when you suddenly open the throttle on an idling engine, rpm should increase, the TPS reading
should change and the MAP sensor value should drop.
PIDS can also be compared using a "graphing multimeter" or on a scope that converts the voltage values to
waveforms.
Comparing the waveforms of several related sensors can help you find faults that might otherwise be
impossible to detect.
SCAN TOOL PID CAPABILITY
Different scan tools have different capabilities to display PIDS.
The OEM scan tools used by new car dealers are capable of displaying every possible PID value that is built
into the engine management system.
Most general purpose aftermarket scan tools do not contain the software that allows them to match the OEM
scan tools in every respect -- but for most applications they can display all the important PIDS.
The trouble is you never know what PIDS are missing until you go looking for one and find it isn't there.
Bummer.
That's why many professional technicians own multiple scan tools: an aftermarket general purpose scan tool,
and one or more OEM scan tools for the makes they most frequently work on.
Page 17
18. Scan tools like TOAD support various PIDS including live data values, the status of switches and other
devices, the readiness status of various OBD II monitors, and other test results.
Live data provides real-time measurements of system inputs.
Statuses tell you if a switch, relay or other device is ON/OFF or has been commanded ON or OFF.
Readiness monitors tell you if the monitors have completed or not.
Test results are measured by the PCM and compared against preprogrammed pass/fail values in teh PCM's
memory.
LIVE DATA:
Air Flow Rate From MAF -- The airflow rate as measured by the mass air flow sensor.
Absolute Throttle Position -- The absolute throttle position (not the relative or learned) throttle
position. Usually above 0% at idle and less than 100% at full throttle.
Calculated Load Value -- Indicates a percentage of peak available torque. Reaches 100% at wide
open throttle at any altitude or RPM for both naturally aspirated and boosted engines.
Engine Coolant Temperature -- Engine coolant temperature as read by the engine coolant
temperature sensor. This value should be compared to the actual coolant temperature to see if they
match.
You can use an infrared thermometer or other thermometer to measure the temperature of the coolant
at the thermostat outlet. If the actual temperature and displayed temperature do not match, it would tell
you the coolant sensor is not reading correctly.
Engine RPM -- The current engine speed in revolutions per minute (RPM).
Fuel Rail Pressure -- Pressure in the fuel rail when the reading is referenced to atmosphere (gauge
pressure).
Ignition Timing Advance -- Degrees of ignition timing (spark) advance for #1 cylinder (not including
mechanical advance). Intake Manifold
Pressure -- Pressure in the intake manifold derived from a Manifold Absolute Pressure (MAP) sensor.
Long Term Fuel Trim (LTFT) -- The correction factor (percentage) being used by the fuel control
system in both open and closed loop modes of operation. LTFT should typically be within plus or minus
five. Positive LTFT numbers indicate the PCM is adding more fuel to compensate for a lean fuel
condition.
Negative LTFT numbers mean the PCM is delivering less fuel to compensate for a rich fuel condition. If
the LTFT is higher than 10 either way, it may indicate a problem.
Short Term Fuel Trim (STFT) -- The correction factor being used in closed loop by the PCM to
maintain a balanced fuel mixture. If the fuel system is open loop, 0% correction should be reported. As
with LTFT, the number should usually be plus or minus five. If greater than 10, it indicates a fuel
mixture problem.
O2 Sensor Output Voltage -- The actual voltage being generated by the oxygen sensor (should be 0.1
to 1.0 volts for a conventional zirconia O2 sensor).
For wide-band O2 sensors and linear O2 sensors, the value may be higher, or it may be converted to a
Page 18
19. zero to one volt scale.
There may be multiple O2 sensor PIDS depending on homw many sensors the engien has (Bank1
sensor 1, Bank2 Sensor 1, etc.).
Time Since Engine Start -- Shows the time the engine has been running since it was last started.
Vehicle Speed -- Displays vehicle road speed as read by the vehicle speed sensor (VSS).
Absolute Load Value -- This is the normalized value of air mass per intake stroke displayed as a
percent.
Absolute Throttle Position -- The absolute throttle position (not the relative or learned) throttle
position. Usually above 0% at idle and less than 100% at full throttle.
Accelerator Pedal Position -- The absolute pedal position (not the relative or learned) pedal position.
Usually above 0% at idle and less than 100% at full throttle.
Ambient Air Temperature -- The ambient air temperature as ready by the air temperature sensor. This
value can be compared to the temperature reading by another thermometer to see if the values match.
If they do not, the air temperature sensor is not reading accurately.
NOTE: the temperature reading will depend on the location of the sensor. If the sensor is located under
the hood, it may read higher than the outside temperatrue when the vehicle is not moving becuase of
engine heat.
Barometric Pressure -- Barometric pressure as determined by a barometric pressure (BARO) sensor.
Note some weather services report barometric pressure adjusted to sea level. In these cases, the
reported value may not match the displayed value.
Catalyst Temp -- The temperature inside the catalytic converter.
Commanded EGR -- Tells you what the PCM is commanding the EGR valve to do.
The percentage vlue should be 0% when EGR is commanded off (at idle), 100% when EGR is
commanded on (typically when cruising under light load), and between 0% and 100% is the EGR
solenoid is duty cycled on and off by the PCM (depending on vehicle speed, engine load and
temperature).
Commanded Equivalence Ratio -- Fuel systems that use conventional oxygen sensor displays the
commanded open loop equivalence ratio while the system is in open loop. Should report 100% when in
closed loop fuel.
To obtain the actual air/fuel ratio being commanded, multiply the stoichiometric A/F ratio by the
equivalence ratio. For example, gasoline, stoichiometric is 14.64:1 ratio.
If the fuel control system was command an equivalence ratio of 0.95, the commanded A/F ratio to the
engine would be 14.64 * 0.95 = 13.9 A/F.
Commanded Evaporative Purge -- This value should read 0% when no purge is commanded and
100% at the maximum commanded purge position/flow.
Commanded Throttle Actuator -- This value should be 0% when the throttle is commanded closed
and 100% when the throttle is commanded open.
Control Module Voltage -- Power input to the control module. Normally, this should show battery
voltage minus any voltage drop between the battery and the control module (which should be less than
a few tenths of a volt).
Page 19
20. Distance Since DTCs Cleared -- How many miles the vehicle has been driven since any DTCs were
cleared with a scan tool. Distance
Traveled While MIL On -- Tells you how many miles the vehicle has been driven with the MIL light on.
Also tells you
how long the driver has been ignoring the light!
EGR Error -- Calculated error as percent of actual commanded EGR. Negative percent is less than
commanded and positive is more than commanded. The greater the value, the more likely the EGR
valve is sticking.
EVAP Purge -- This value is displayed as a percentage and is normalized for all types of EVAP
systems. When EVAP purge is commanded off, the value should be o%, and 100% when it is
commanded on.
This is an important value o check if the engine has lower than normal LTFT and STFT fuel trim
numbers (indicating a rich fuel condition). The purge valve may be leaking vapor into the intake
manifold.
To eliminate the purge valve as a possible source of fuel vapor, pinch off the purge vapor hose, run the
engine and recheck the STFT number. If it is back to normal, the purse valve is leaking.
EVAP System Vapor Pressure -- Evaporative system vapor pressure normally obtained from a sensor
located in the fuel tank.
Fuel Level Input -- Indicates the nominal fuel tank liquid fill capacity as a percent of maximum.
Fuel Rail Pressure -- Indicates the fuel rail pressure at the engine referenced to atmosphere (gauge
pressure).
Fuel Rail Pressure Rel Manifold -- The fuel rail pressure referenced to the manifold vacuum (relative
pressure).
Intake Air Temperature -- The temperature of the air in the intake manifold as read by the intake
manifold air temperature sensor. This should be the same as ambient temperature in a cold engine that
has not been started, and should be higher than ambient tempertarue if teh engine is warm and has
been running.
Minutes Run with MIL On -- Accumulated minutes of engine run time while the MIL light is on.
O2 Sensor Wide Range mA -- Milliamp current for linear or wide-ratio oxygen sensors.
O2 Sensor Wide Range V -- Voltage for linear or wide-ratio oxygen sensors.
Relative Throttle Position -- Relative or learned throttle position.
Time Since DTCs Cleared -- Accumulated time since DTCs where cleared with a scan tool.
Warm-ups Since DTCs Cleared -- Number of warm-up cycles since all DTCs were cleared with a scan
tool. A warm-up is defined as the coolant temperature rising by at least 22°C (40°F) and the engine
temperature reaches at a minimum 70°C (160°F), or 60°C (140°F) for diesel engines.
TROUBLE CODES AND FREEZE FRAME DATA
Page 20
21. Code readers and scan tools will also display Stored Diagnostic Trouble Codes (DTCs), usually in numeric
order.
Many scan tools can also display Pending Trouble Codes.
These are codes that indicate a fault has been detected, but that the fault has not yet repeated.
If the fault repeats under similar driving conditions, it will usually cause the Pending Code to become a Stored
Code and turn on the MIL light.
Many scan tools can also display Freeze Frame data.
These are PIDS that are captured when a fault occurs so you can refer to them later when diagnosing the
problem.
Freeze frame data typically includes related sensor values at the time the fault occurred.
STATUS AND READINESS MONITORS
OBD II requires the following status and readiness monitors:
Fuel System 1 Status
Fuel System 2 Status
Secondary Air Status
Auxiliary Input Status
Misfire Monitor Status
Fuel System Status
Comprehensive Component Monitoring Status
Catalyst Monitoring Status
Heated Catalyst Monitoring Status
Evaporative System Monitoring Status
Secondary Air System Monitoring Status
A/C System Refrigerant Monitoring Status
Oxygen Sensor Monitoring Status
Oxygen Sensor Heater Monitoring Status
EGR System Monitoring Status
ECU Oxygen Sensor Test Results
Page 21
23. How Car Diagnostic Software and Tools Work
February 17, 2012
Most car diagnostic software is based on reading data from your vehicle's OBD-II (onboard
diagnostic) system. Learn how to use a car diagnostic tool.
Car diagnostic software helps keep your vehicle running smoothly. This software is built into all cars
made after 1996, and it is included in many earlier cars as well. The latest technology is called OBD-
II, which stands for on board diagnostic system. The OBD-II is incredibly useful to mechanics and
other people curious about the status of their vehicle when something seems to go wrong.
Positioning of the Software
The OBD-II system in your vehicle has sensors and ports in various parts of the car. There is one
underneath the dash of most cars, and many vehicles also have a port under to the driver's seat.
There are other sensors and activation centers spread throughout the vehicle in order to monitor the
activity of various parts of the car. Essentially, the software is located all throughout the vehicle.
Function of the Software
The OBD-II monitors the proper functioning of your vehicle. It not only controls certain engine
functions through the on board computer, it also keeps a record of all of the things that happen to
your car as you drive it, good and bad. This information can be used later by mechanics, who
download a series of diagnostic codes from the OBD-II port. These codes explain what is going on
with the vehicle, and are the basis for the diagnosis of your problem and how to fix it when the check
engine light comes on or if you experience other problems.
Process
The software that measures the diagnostics of your car takes regular readings of different systems in
the car. This is primarily centered on the engine, but the OBD-II includes sensors for the chassis,
frame and other parts of the car too. At each reading, the software records a particular acronym or
code that represents the functionality of that system. This information is stored within the OBD-II
system and can be retrieved by attaching a computer to the port. The mechanic then downloads the
codes and translates them to determine exactly what was going on at each point of inspection. This
helps to calculate when and how damage occurred to a part of your car.
How to Use a Car Diagnostic Tool
An auto scan tool can be used to read the diagnostic software. Also called a car code reader or an
OBD-II scanner, this tool is a useful way to determine the issues with your car without having to take
it in to a dealership or a mechanic for an expensive analysis.
You'll need the following materials in order to take a diagnostic reading of your car:
Page 23
24. A Laptop, iPhone or iPod Touch
Jack cables and a port connector
A scanner or car code reader
A breakdown of codes and acronyms for your vehicle
Install the Computer Software
Computer scanner systems require that you connect the scanner to a computer. An iPhone or iPod
Touch will also work with devices such as the REV iPhone Car Diagnostic Tool. In order to get a
reading from the car diagnostic device, install the software that comes with the scanner system. This
allows the computer to display the readings from the diagnostic tool.
Connect the Scanner
Find the port where you can attach the scanner. This port is often located on the dash, typically just
below the steering wheel and to one side or another. Look for a small indentation and a simple port
system. The port connector may also be underneath the driver's side of the front seat. If you're having
a hard time figuring out where to connect your scanner, check the owner's manual for your car or
consult with a professional.
Get a Reading
Follow the instructions from the scanner tool and the software on your computer to take a reading of
the car diagnostic device. This will help you to determine exactly what the problem is by sending a
series of codes to your computer, which will be displayed.
Translate the Codes
Using the guidelines from the code translation sheet, figure out the problem that has caused the
malfunction or the check engine light to come on. You can then decide the best way to remedy the
problem or take your car to a mechanic.
Page 24
25. CHOOSING THE RIGHT SCAN TOOL
THE FOUR CRITICAL STEPS TO CHOOSING A SCAN TOOL THAT’S RIGHT FOR YOUR SHOP
BRYCE EVANS
STAFF GRAPHIC
THE FOUNDATION OF A PROPER REPAIR IS “IN THE PREPARATION,” SAYS ROBBIE BERMAN. AN
HOUR OF PREP TIME BEFORE A JOB CAN CUT OUT SUPPLEMENTS, ELIMINATE DELAYS IN PARTS
ORDERING, SHAVE CYCLE TIME AND, ULTIMATELY, IMPROVE THE FINAL PRODUCT AND THE
CUSTOMER EXPERIENCE.
THIS SHOULD BE OBVIOUS TO EVERY SHOP, BERMAN SAYS, BUT TOO OFTEN IT’S NOT.
BERMAN STARTED HIS CAREER AND HIS SHOP, ROBBIE’S AUTOMOTIVE AND COLLISION
SPECIALISTS IN WHARTON, N.J., WITH A FOCUS ON MECHANICAL REPAIR. AND HE SAYS THAT IF
THERE’S ONE THING THE COLLISION INDUSTRY CAN LEARN FROM MECHANICAL SHOPS, IT’S THE
IMPORTANCE OF DIAGNOSTICS.
“DIAGNOSTICS IS EVERYTHING, AND IT’S ONLY GROWING.” HE SAYS. “EVERY CAR COMING DOWN
THE ROAD HAS MORE AND MORE TECHNOLOGY IN IT, MORE AND MORE COMPUTER SYSTEMS.
WITHOUT THE RIGHT DIAGNOSTIC EQUIPMENT AND PROCESSES, YOU’RE NOT GOING TO BE ABLE
TO FIX VEHICLES ANYMORE.”
DIAGNOSTIC SCAN TOOLS ARE SOMETHING THAT HIS $4 MILLION, 10,000-SQUARE-FOOT COLLISION
BUSINESS HAS INVESTED IN FOR YEARS, BUT AS AN INDUSTRY, BERMAN SAYS, IT’S SOMETHING
THAT TOO MANY SHOPS ARE MISSING OUT ON.
BOB KEITH, SHOP OWNER AND DIRECTOR OF EDUCATION AND TRAINING WITH CARSTAR, AGREES.
Page 25
26. AND, LIKE ANY EQUIPMENT OR TOOL PURCHASE A SHOP CAN MAKE, INVESTING IN DIAGNOSTIC
SCAN TOOLS IS EXACTLY THAT—AN INVESTMENT, SOMETHING SHOPS NEED TO RESEARCH,
UNDERSTAND AND WEIGH OPTIONS ON BEFORE PURCHASING.
WHEN IT COMES TO SCAN TOOLS, THERE ARE DOZENS AND DOZENS OF OPTIONS FOR COLLISION
FACILITIES. BERMAN AND KEITH HELPED FENDERBENDER SIMPLIFY THE PURCHASING PROCESS,
OFFERING THEIR TIPS ON MATCHING YOUR BUSINESS TO THE RIGHT TOOL.
UNDERSTAND THE VALUE
KEITH LIKES TO KEEP THINGS LIGHTHEARTED IN HIS NATIONWIDE TRAINING COURSES HE RUNS
FOR CARSTAR, AND, IN DEALING WITH THE TOPIC OF TOOL AND EQUIPMENT PURCHASES, HE
LIKES TO POINT TO A ONE-PANEL COMIC.
THERE ARE A NUMBER OF VERSIONS, BUT THE GENERAL PICTURE IS THIS: A GROUP OF KNIGHTS
ARE GRABBING THEIR SWORDS AND STRAPPING ON ARMOR, GETTING READY FOR BATTLE.
BEHIND THEM STANDS A SALESMAN WITH A MACHINE GUN LOADED INTO A WAGON. THE CAPTION,
COMING FROM THE LEADER OF THE KNIGHTS, SAYS, “CAN’T THEY SEE WE DON’T HAVE TIME FOR
THIS? WE HAVE A BATTLE TO FIGHT!”
“IT CRACKS ME UP, BECAUSE YOU TALK TO A LOT OF SHOPS AROUND THE COUNTRY, AND THAT’S
THE APPROACH THEY TAKE TO TOOLS AND EQUIPMENT,” HE SAYS. “PEOPLE LOOK AT IT AS A
COST. TO AN EXTENT, IT IS, BUT YOU HAVE TO UNDERSTAND THE INVESTMENT AND THE BENEFITS
IT CAN BRING. IT’S EASY TO GET TOO CAUGHT UP IN WHAT YOU’RE DOING TO TAKE A MOMENT
AND LOOK AT THE BIGGER PICTURE OF HOW THAT INVESTMENT WILL AFFECT YOUR BUSINESS.”
EVEN BASIC, AFTERMARKET SCAN TOOLS COME WITH A FIVE-FIGURE PRICE TAG, BERMAN SAYS,
RANGING FROM $10,000–$30,000. THEN, THERE’S ANNUAL SUBSCRIPTION FEES (NORMALLY
AROUND $1,500) TO THE VEHICLE INFORMATION THE DEVICES READ.
IT’S A SUBSTANTIAL INVESTMENT FOR A COLLISION SHOP TO MAKE, BUT WITHOUT IT, WELL,
YOU’RE SIMPLY OPTING TO USE A SWORD OVER A MACHINE GUN.
“THE BENEFITS OF HAVING THE RIGHT TOOL, THE ONE THAT FITS INTO YOUR BUSINESS, FAR
OUTWIEGHS THE COST,” BERMAN SAYS. “YOU’RE INVESTING IN YOUR SHOP’S ABILITY TO
PROPERLY PERFORM WORK NOW AND IN THE FUTURE.”
THERE ARE FIVE CRITICAL STEPS TO ENSURE YOUR SHOP CHOOSES THE CORRECT SCAN TOOL.
STEP 1: IDENTIFY YOUR NEED.
WITH THE INCREASE OF IN-VEHICLE TECHNOLOGY AND COMPUTER SYSTEMS, BERMAN SAYS
EVERY SHOP NEEDS PROPER DIAGNOSTIC EQUIPMENT REGARDLESS OF THEIR WORK MIX.
HOWEVER, WHICH TOOL (OR TOOLS) YOU CHOOSE IS 100 PERCENT DETERMINED BY THAT WORK
MIX.
BOTTOM LINE: YOU NEED TO INVEST IN THE TOOLS TO FIX THE VEHICLES YOU WORK ON THE
MOST.
BERMAN SUGGESTS TAKING A HARD LOOK AT THE VEHICLES YOUR SHOP REPAIRS, RANKING
THEM FROM MOST FREQUENT TO LEAST FREQUENT. THE TOP-10 VEHICLES, HE SAYS, ARE THE
ONES YOU NEED TO FOCUS YOUR EFFORTS ON.
“IT WOULD BE GREAT TO GO TO 20 MAKES AND MODELS, OR 30, BUT IT’S UNLIKELY YOU’RE GOING
TO HAVE THE FUNDING FOR THAT,” HE SAYS. “IF YOU FOCUS ON THE ONES YOU NEED THE
MOST—AND THAT’D BE THAT TOP 10—YOU’RE GOING TO BE ABLE TO PROPERLY DIAGNOSE THE
VAST MAJORITY OF VEHICLES THAT ENTER YOUR SHOP.”
Page 26
27. REMEMBER, BERMAN SAYS, THAT MANY SCAN DEVICES WORK FOR MULTIPLE MAKES, MODELS
AND YEARS—MEANING THAT THE TOOL(S) YOU CHOOSE TO SUPPORT THOSE 10 VEHICLE MAKES
VERY LIKELY COULD COVER NEARLY EVERY VEHICLE YOU WORK ON.
WHICH BRINGS US TO …
STEP 2: RESEARCH TOOLS.
THIS IS WHERE THE PROCESS MAY SEEM DAUNTING, BERMAN SAYS, BUT IT DOESN’T NEED TO. IF
YOU HAVE AN UNDERSTANDING OF WHAT YOU NEED THE TOOL(S) TO DO (E.G., PROPERLY
DIAGNOSE THOSE 10 VEHICLE LINES), THEN THE SITUATION IS ALREADY SIMPLIFIED.
WHEN LOOKING AT SCAN TOOLS, BERMAN SUGGESTS FOCUSING ON THESE FIVE
CHARACTERISTICS OF THE TOOL AND THE COMPANY THAT PROVIDES IT:
1. COVERAGE. DEPENDING ON THE BRAND, WHETHER IT’S AN OEM OR AFTERMARKET TOOL, AND
THE VARIOUS MODELS, EACH SCAN TOOL IS GOING TO BE ABLE TO PROVIDE DIFFERENT
INFORMATION TO A REPAIRER. THEY WILL HAVE DIFFERENT ACCESS TO MANUFACTURER CODES,
AND THEY WILL BE ABLE TO ACCESS DIFFERENT LEVELS OF THE VEHICLE’S SYSTEMS. AS BERMAN
POINTS OUT, YOUR TOOL NEEDS TO COVER ALL ASPECTS OF EVERY ONE OF YOUR TOP-10
VEHICLES.
2. TRAINING/EASE OF USE. BERMAN SAYS THERE CAN BE A DRASTICALLY DIFFERENT LEARNING
CURVE BETWEEN BRANDS AND MODELS OF SCAN TOOLS. IN HIS SHOP, HE HAS TWO DIFFERENT
AFTERMARKET SCAN TOOLS—ONE FROM SNAP-ON AND ANOTHER FROM OTC—AND EACH, HE
SAYS, ARE RELATIVELY SIMPLE TO USE, AND BOTH COMPANIES PROVIDE AMPLE TRAINING.
3. TECHNICAL SUPPORT. THERE ARE STILL GOING TO BE TIMES WHEN A TECHNICIAN IS UNABLE
TO PULL A CODE, OR A CODE MAY NOT MAKE SENSE TO THE ISSUES THE VEHICLE HAS. BERMAN
SAYS THIS IS WHY HAVING STRONG TECHNICAL SUPPORT FROM THE COMPANY THAT PROVIDES
THE TOOL CAN HELP YOU UNDERSTAND WHETHER THERE IS AN ISSUE WITH THE TOOL ITSELF OR
SIMPLY USER ERROR.
4. UPGRADES AND UPDATES. THE MAKEUP OF VEHICLES CHANGES RAPIDLY, AND BERMAN SAYS
TO MAKE SURE YOU HAVE A TOOL THAT KEEPS UP WITH THE LATEST NEEDS OF REPAIRERS—
EITHER THROUGH SUBSCRIPTION UPDATES OR UPGRADES TO THE TOOL ITSELF. SOME
COMPANIES PROVIDE TRADE-IN OFFERS FOR UPGRADES, HE SAYS.
5. COST. THIS IS OBVIOUSLY AN IMPORTANT ASPECT, BUT BOTH KEITH AND BERMAN SAY TO KEEP
IT LAST ON THIS LIST. COST IS ONLY RELATIVE TO THE EFFECT THE TOOL WILL HAVE ON YOUR
BUSINESS, WHICH CAN EASILY BE MEASURED IN THE NEXT STEP.
STEP 3: ANALYZE THE RETURN ON INVESTMENT (ROI).
KEITH SAYS THAT, DESPITE WHAT SOME PEOPLE ASSUME ABOUT ROI, IT CAN ACTUALLY BE
PROPERLY CALCULATED BEFORE A PURCHASE IS EVER MADE. HERE ARE HIS THREE SIMPLE
STEPS TO DOING THAT:
1. STUDY THE PROBLEM. IN THE CASE OF A SCAN TOOL PURCHASE, KEITH SAYS TO LOOK AT HOW
THE CURRENT PROCESS PLAYS OUT IN YOUR SHOP WITHOUT THE NEW TOOL. LOOK FOR THE
INEFFICIENCIES: ARE YOUR TECHS FORCED TO SHARE OR SEARCH FOR THE CURRENT TOOLS?
DO THEY HAVE TO OUTSOURCE THE WORK BECAUSE YOU DON’T HAVE ONE AT ALL? WHAT’S THE
LOSS IN PRODUCTIVITY, CYCLE TIME, SALES, REVENUE AND PROFIT? ADD IT UP, KEITH SAYS, AND
SEE HOW MUCH YOUR SHOP IS LOSING IN BOTH EFFICIENCY OR DOLLARS. PUT A NUMBER TO IT.
2. UNDERSTAND HOW THE NEW TOOL MAKES A DIFFERENCE. BECAUSE YOU HAVE AN IDEA OF
THE TOOLS YOU’D LIKE TO PURCHASE FROM STEP 2, YOU CAN ANALYZE HOW THE NEW TOOL
WILL AFFECT THOSE EFFICIENCY AND REVENUE NUMBERS. HOW MUCH TIME DOES IT SHAVE OFF
Page 27
28. IN PRODUCTION? HOW MUCH MONEY DOES IT ADD TO YOUR SHOP’S SALES? AGAIN, PUT A
NUMBER TO IT.
3. COMPARE SAVINGS TO COST. KEITH SAYS THE FINAL STEP IS TO SIMPLY COMPARE THE
POTENTIAL MONEY SAVED AND THE IMPROVED EFFICIENCY CREATED TO THE TOTAL COST OF
THE TOOL INCLUDING SUBSCRIPTIONS. THAT’S YOUR ESTIMATED ROI, AND IT SHOULD GIVE YOU A
GOOD SENSE OF HOW LONG IT WILL TAKE TO ACHIEVE THAT BREAK-EVEN POINT. NOTE THAT THIS
CALCULATION IS TO HELP YOU BEST DETERMINE THE QUALITY OF YOUR PURCHASE; EVERYDAY
BUSINESS SITUATIONS CAN CAUSE CHANGES DOWN THE ROAD.
STEP 4: IMPLEMENT THE TOOL
WORKING THROUGH THE FIRST THREE STEPS SHOULD PROVIDE YOU WITH A TOOL OR LIST OF
TOOLS THAT WILL IMPROVE YOUR BUSINESS’S EFFICIENCY AND SALES—AT LEAST, IN THEORY.
THE KEY TO MAKING THAT PURCHASE, OR PURCHASES, TRULY HAVE VALUE IN YOUR SHOP
COMES FROM PROPER IMPLEMENTATION, KEITH SAYS.
BERMAN SAYS TO CREATE A STANDARD OPERATING PROCEDURE IN YOUR SHOP THAT OUTLINES
WHEN THE TOOL SHOULD BE USED AND WHO IS ASSIGNED TO PERFORM THE SCAN.
IN BERMAN’S SHOP, HE HAS TWO OF HIS TECHNICIANS FROM THE MECHANICAL SEGMENT
PERFORM THE SCANS BOTH DURING THE BLUEPRINTING PROCESS AND AFTER THE REPAIR IS
COMPLETED.
Page 28
29. ProScan Help : Diagnostic Trouble Code Breakdown
DTCs are composed of five characters; one letter followed by 4 digits.
Example DTCs:
P0134
P1155
B0042
C1132
U3201
Digit 1 = System Identifier
Digit 1 System
P Powertrain
B Body
C Chassis
U Undefined
Digit 2 = Type of Code Definition
Generic:
Same definition for all manufacturers.
Manufacturer-Specific:
Definition varies among manufacturers.
Digit 2 Type of Code Definition
0 Generic
1 Manufacturer-Specific
2 P2xxx = Generic
B2xxx = Manufacturer-Specific
C2xxx = Manufacturer-Specific
U2xxx = Manufacturer-Specific
3 P30xx – P33xx = Manufacturer-Specific
Página 1 de 2ProScan Help : Diagnostic Trouble Code Breakdown
16/08/2016mk:@MSITStore:C:Archivos%20de%20programaProScanProScan_Help.chm::/dtc...
Page 29
30. P34xx – P39xx = Generic
B3xxx = Generic
C3xxx = Generic
U3xxx = Generic
Digit 3 = Sub-System
Digit 3 Sub-System
1 Fuel & Air Metering
2 Fuel & Air Metering
(Injector Circuit Malfunction Only)
3 Ignition System or Misfire
4 Auxiliary Emission Control System
5 Vehicle Speed Control & Idle Control System
6 Computer Output Circuits
7-8 Transmission
Digits 4 & 5
The fourth and fifth digits of the DTC identify the specific problem.
Página 2 de 2ProScan Help : Diagnostic Trouble Code Breakdown
16/08/2016mk:@MSITStore:C:Archivos%20de%20programaProScanProScan_Help.chm::/dtc...
Page 30
31. ProScan Help : Oxygen Sensor and Catalyst Configuration Example
Página 1 de 2ProScan Help : Oxygen Sensor and Catalyst Configurations
16/08/2016mk:@MSITStore:C:Archivos%20de%20programaProScanProScan_Help.chm::/o2c...
Page 31
32. Página 2 de 2ProScan Help : Oxygen Sensor and Catalyst Configurations
16/08/2016mk:@MSITStore:C:Archivos%20de%20programaProScanProScan_Help.chm::/o2c...
Page 32
33. OBDII: Past, Present and Future Pg 1 of 5 http://www.autotap.com
OBDII: PAST, PRESENT & FUTURE
All 1996 and newer model year passenger cars and light trucks are OBDII-equipped, but the first applications
were actually introduced back in ‘94 on a limited number of vehicle models.
What makes OBDII different from all the self-diagnostic systems that proceeded it is that OBDII is strictly
emissions oriented. In other words, it will illuminate the Malfunction Indicator Lamp (MIL) anytime a vehicle’s
emissions exceed 1.5 times the federal test procedure (FTP) standards for that model year of vehicle. That
includes anytime random misfires cause an overall rise in HC emissions, anytime the operating efficiency of the
catalytic converter drops below a certain threshold, anytime the system detects air leakage in the sealed fuel
system, anytime a fault in the EGR system causes NOX emissions to go up, or anytime a key sensor or other
emission control device fails. In other words, the MIL light may come on even though the vehicle seems to be
running normally and there are no real driveability problems.
The main purpose of the MIL lamp on an OBDII-equipped vehicle, therefore, is to alert you when your vehicle is
polluting so you’ll get their emission problems fixed. But as we all know, its easy to ignore warning lamps— until
steam is belching from under the hood or the engine is making horrible noises. That’s why regulators want to
incorporate OBDII into existing and enhanced vehicle emissions inspection programs. If the MIL lamp is found to
be on when a vehicle is tested, it doesn’t pass even if its tailpipe emissions are within acceptable limits.
WHY OBDII?
The problem with most vehicle inspection programs is that they were developed back in the 1980s to identify
"gross polluters." The tests were designed primarily to measure idle emissions on carbureted engines (which are
dirtiest at idle), and to check for only two pollutants: unburned hydrocarbons (HC) and carbon monoxide (CO).
The pass/fail cut points that were established for the various model years were also made rather lenient to
minimize the number of failures. Consequently, a lot of late model vehicles that shouldn’t be passing an
emissions test are getting through anyway.
Efforts to upgrade vehicle inspection programs to the new I/M 240 standards have stalled because of a lack of
public and political support. The I/M 240 program would have required "loaded-mode" emissions testing on a
dyno while the vehicle was driven at various speeds following a carefully prescribed driving trace. While this was
going on, the tailpipe gases would be analyzed to check not only for total emissions. The total emissions for the
entire 240-second driving cycle would then be averaged for a composite emission score that determines
whether or not the vehicle passed the test. Also included would be an evaporative purge flow test to measure
the flow rate of the canister purge valve, and an engine off pressure test of the evaporative emission control
system to check the fuel tank, lines and cap for leaks.
The I/M 240 program was to have been required in most areas of the country that don’t meet national ambient
air quality (NAAQ) standards. But after the program faltered in Maine, most states balked and only Colorado
went ahead with the program. The cost and complexity of the I/M 240 program combined with less than
enthusiastic public acceptance doomed it from the start. So it’s now up to the individual states to come up with
alternative plans for improving their air quality. An important element in many of those plans is OBDII.
A SHORT HISTORY WITH FAR REACHING IMPLICATIONS
The origins of OBDII actually date back to 1982 in California, when the California Air Resources Board (ARB)
began developing regulations that would require all vehicles sold in that state starting in 1988 to have an
onboard diagnostic system to detect emission failures. The original onboard diagnostic system (which has since
become known as OBDI) was relatively simple and only monitored the oxygen sensor, EGR system, fuel
delivery system and engine control module.
Page 33
34. OBDII: Past, Present and Future Pg 2 of 5 http://www.autotap.com
OBDI was a step in the right direction, but lacked any requirement for standardization between different makes
and models of vehicles. You still had to have different adapters to work on different vehicles, and some systems
could only be accessed with costly "dealer" scan tools. So when ARB set about to develop standards for the
current OBDII system, standardization was a priority: a standardized 16-pin data link connector (DLC) with
specific pins assigned specific functions, standardized electronic protocols, standardized diagnostic trouble
codes (DTCs), and standardized terminology.
Another limitation of OBDI was that it couldn’t detect certain kinds of problems such as a dead catalytic
converter or one that had been removed. Nor could it detect ignition misfires or evaporative emission problems.
Furthermore, OBDI systems would only illuminate the MIL light after a failure had occurred. It had no way of
monitoring progressive deterioration of emissions-related components. So it became apparent that a more
sophisticated system would be required. The California Air Resources Board eventually developed standards for
the next generation OBD system, which were proposed in 1989 and became known as OBDII. The new
standards required a phase-in starting in 1994. The auto makers were given until the 1996 model year to
complete the phase-in for their California vehicles.
Similar standards were incorporated into the federal Clean Air Act in 1990 which also required all 49-state
vehicles to be OBDII equipped by 1996 -- with one loophole. The OBDII systems would not have to be fully
compliant until 1999. So some 1996 OBDII systems may lack one of the features normally required to meet the
OBDII specs, such as the evaporative emissions purge test.
EARLY OBDII APPLICATIONS
1994 vehicles equipped with the early OBD II systems include Buick Regal 3800 V6, Corvette, Lexus ES3000,
Toyota Camry (1MZ-FE 3.0L V6) and T100 pickup (3RZ-FE 2.7L four), Ford Thunderbird & Cougar 4.6L V8, and
Mustang 3.8L V6.1995 vehicles with OBDII include Chevy/GMC S, T-Series pickups, Blazer and Jimmy 4.3L V6,
Ford Contour & Mercury Mystique 2.0L four & 2.6L V6, Chrysler Neon, Cirrus and Dodge Stratus, Eagle Talon
2.0L DOHC (nonturbo), and Nissan Maxima and 240 SX.
Not all of these early applications are fully OBDII compliant, but do include the major diagnostic features of the
current system.
OBDII HARDWARE UPGRADES
Don’t think for a moment that OBDII is just a fancier version of self-diagnostic software. It’s that and much, much
more.OBDII-equipped vehicles typically have:
• Twice the number of oxygen sensors as non-OBDII vehicles(most of which are heated O2 sensors). The
additional O2 sensors are located downstream of the catalytic converter.
• More powerful powertrain control modules, with either16-bit (Chrysler) or 32-bit (Ford & GM) processors
to handle up to 15,000 new calibration constants that were added by OBDII.
• Electronically Erasable Programmable Read Only Memory(EEPROM) chips that allows the PCM to be
reprogrammed with revised or updated software changes using a terminal link or external computer.
• A modified evaporative emission control systems with a diagnostic switch for purge testing, or an
enhanced EVAP system with a vent solenoid, fuel tank pressure sensor and diagnostic test fitting,
• More EGR systems with a linear EGR valve that is electronically operated and has a pintle position
sensor.
• Sequential fuel injection rather than multiport or throttle body injection. Both a MAP sensor and MAF
sensor for monitoring engine load and airflow.
Page 34
35. OBDII: Past, Present and Future Pg 3 of 5 http://www.autotap.com
TOOLING UP FOR OBDII
To work on your OBDII-equipped vehicle, you’ll need an OBDII scan tool such as AutoTap for PC or Palm PDA.
THAT PESKY MIL LAMP
Most technicians are pretty familiar with the operation of the "Check Engine" or "Malfunction Indicator Lamp"
(MIL) on late model vehicles. But on OBDII-equipped vehicles, it may seem like the MIL lamp has a mind of its
own.
On ‘96 General Motors J-, N- and H-body cars, several rental fleets have encountered problems with the MIL
lamp coming on because motorists and fleet personnel haven’t been using the correct refueling procedure when
filling the fuel tank with gas. On these cars, the OBDII system applies vacuum to the evaporative emissions
control system to check for air leakage. If the gas cap isn’t tight or the tank is filled while the key is on or the
engine is idling, it can trigger a false P0440 code causing the MIL light to come on. GM has not issued a
technical service bulletin on the problem, but is advising its dealers and fleet customers to reflash the EEPROM
with revised OBDII programming that waits to check the evaporative emissions system until the vehicle is in
motion.
Bad gas has also been causing some false MIL lights. When the vehicle is diagnosed, the technician finds a
P0300 random misfire code which would normally be set by a lean misfire condition due to a vacuum leak, low
fuel pressure, dirty injectors, etc., or an ignition problem such as fouled plugs, bad plug wires, weak coil, etc.
The OBDII self-diagnostics tracks misfires by individual cylinder, and considers up to a 2% misfire rate as
normal. But water in the gas or variations in the additive package in reformulated gasoline in some areas of the
country can increase the misfire rate to the point where it triggers a code.
To minimize the occurrence of false MIL lamps, the OBDII system is programmed so that the MIL lamp only
comes on if a certain kind of fault has been detected twice under the same driving conditions. With other faults
(those that typically cause an immediate and significant jump in emissions), the MIL light comes on after only a
single occurrence. So to correctly diagnose a problem, it’s important to know what type of code you’re dealing
with.
Type A diagnostic trouble codes are the most serious and will trigger the MIL lamp with only one occurrence.
When a Type A code is set, the OBDII system also stores a history code, failure record and freeze frame data to
help you diagnose the problem.
Type B codes are less serious emission problems and must occur at least once on two consecutive trips before
the MIL lamp will come on. If a fault occurs on one trip but doesn’t happen again on the next trip, the code won’t
"mature" and the light will remain off. When the conditions are met to turn on the MIL lamp, a history code,
failure record and freeze frame data are stored the same as with Type A codes.
A drive cycle or trip, by the way, is not just an ignition cycle, but a warm-up cycle. It is defined as starting the
engine and driving the vehicle long enough to raise the coolant temperature at least 40 degrees F (if the startup
temperature is less than 160 degrees F).
Once a Type A or B code has been set, the MIL will come on and remain on until the component that failed
passes a self-test on three consecutive trips. And if the fault involved something like a P0300 random misfire or
a fuel balance problem, the light won’t go out until the system passes a self-test under similar operating
conditions (within 375 rpm and 10% of load) that originally caused it to fail. That’s why the MIL lamp won’t go out
until the emissions problem has been repaired. Clearing the codes with your AutoTap scan tool or disconnecting
the powertrain control module’s power supply won’t prevent the lamp from coming back on if the problem hasn’t
been fixed. It may take one or more driving cycles to reset the code, but sooner or later the MIL lamp will go
back on if the problem is still there.
Likewise, the MIL won’t necessarily go on if you intentionally disconnect a sensor. It depends on the priority
ranking of the sensor (how it affects emissions), and how many driving cycles it takes for the OBDII diagnostics
to pick up the fault and set a code.
Page 35
36. OBDII: Past, Present and Future Pg 4 of 5 http://www.autotap.com
As for Type C and D codes, these are non-emissions related. Type C codes can cause the MIL lamp to come on
(or illuminate another warning lamp), but Type D codes do not cause the MIL lamp to come on.
RUNNING AN OBDII DRIVE CYCLE
Suppose you’ve "fixed" an emissions problem on your OBDII-equipped vehicle. How can you check your work?
By performing what’s called an "OBDII drive cycle." The purpose of the OBDII drive cycle is to run all of the
onboard diagnostics. The drive cycle shold be performed after you’ve erased any trouble codes from the PCM’s
memory, or after the battery has been disconnected. Running through the drive cycle sets all the system status
"flags" so that subsequent faults can be detected.
The OBDII drive cycle begins with a cold start (coolant temperature below 122 degrees F and the coolant and
air temperature sensors within 11 degrees of one another).
NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic
may not run.
1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear
defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.
2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition
misfire, fuel trim and canister purge.
3. Hold at a steady state speed of 55 mph for three minutes. OBDII monitors EGR, air pump, O2 sensors
and canister purge.
4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and
purge functions.
5. Accelerate back to 55 to 60 mph at ¾ throttle. OBDII checks misfire, fuel trim and purge again.
6. Hold at a steady speed of 55 to 60 mph for five minutes. OBDII monitors catalytic converter efficiency,
misfire, EGR, fuel trim, oxygen sensors and purge functions.
7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister
purge.
BEYOND OBDII
OBDII is a very sophisticated and capable system for detecting emissions problems. But when it comes to
getting motorists to fix emission problems, it’s no more effective than OBDI. Unless there’s some means of
enforcement, such as checking the MIL light during a mandatory inspection, OBDII is just another idiot light.
Currently under consideration are plans for OBDIII, which would take OBDII a step further by adding telemetry.
Using miniature radio transponder technology similar to that which is already being used for automatic electronic
toll collection systems, an OBDIII-equipped vehicle would be able to report emissions problems directly to a
regulatory agency. The transponder would communicate the vehicle VIN number and any diagnostic codes that
were present. The system could be set up to automatically report an emissions problem via a cellular or satellite
link the instant the MIL light comes on, or to answer a query from a cellular, satellite or roadside signal as to its
current emissions performance status.
What makes this approach so attractive to regulators is its effectiveness and cost savings. Under the current
system, the entire vehicle fleet in an area or state has to be inspected once every year or two to identify the 30%
or so vehicles that have emissions problems. With remote monitoring via the onboard telemetry on an OBDIII-
equipped vehicle, the need for periodic inspections could be eliminated because only those vehicles that
reported problems would have to be tested.
Page 36
37. OBDII: Past, Present and Future Pg 5 of 5 http://www.autotap.com
On one hand, OBDIII with its telemetry reporting of emission problems would save consumers the
inconvenience and cost of having to subject their vehicle to an annual or biennial emissions test. As long as
their vehicle reported no emission problems, there’d be no need to test it. On the other hand, should an
emissions problem be detected, it would be much harder to avoid having it fixed—which is the goal of all clean
air programs anyway. By zeroing in on the vehicles that are actually causing the most pollution, significant gains
could be made in improving our nation’s air quality. But as it is now, polluters may escape detection and repair
for up to two years in areas that have biennial inspections. And in areas that have no inspection programs,
there’s no way to identify such vehicles. OBDIII would change all that.
The specter of having Big Brother in every engine compartment and driving a vehicle that rats on itself anytime it
pollutes is not one that would appeal to many motorists. So the merits of OBDIII would have to be sold to the
public based on its cost savings, convenience and ability to make a real difference in air quality. Even so, any
serious attempt to require OBDIII in the year 2000 or beyond will run afoul of Fourth Amendment issues over
rights of privacy and protection from government search and seizure. Does the government have the right to
snoop under your hood anytime it chooses to do so, or to monitor the whereabouts of your vehicle? These
issues will have to be debated and resolved before OBDIII stands a chance of being accepted. Given the
current political climate, such drastic changes seem unlikely.
Another change that might come with OBDIII would be even closer scrutiny of vehicle emissions. The misfire
detection algorithms currently required by OBDII only watch for misfires during driving conditions that occur
during the federal driving cycle, which covers idle to 55 mph and moderate acceleration. It does not monitor
misfires during wide open throttle acceleration. Full range misfire detection will be required for 1997 models.
OBDIII could go even further by requiring "fly-by-wire" throttle controls to reduce the possibility of misfires on the
coming generation of low emission and ultra low emission vehicles.So until OBDIII winds its way through the
regulatory process, all we have to worry about is diagnosing and repairing OBDII-equipped vehicles and all the
non-OBD vehicles that came before them.
AutoTap – OBDII Automotive Diagnostic Tool
http://www.autotap.com
Page 37
38. CHOOSING THE RIGHT SCAN TOOL FOR YOUR SHOP
HOW CHOOSING THE RIGHT DIAGNOSTIC SCAN TOOL CAN INCREASE YOUR SHOP’S PROFITABILITY
BRYCE EVANS
FIND THE RIGHT FIX EVERY SHOP HAS DIFFERENT USES FOR DIAGNOSTIC EQUIPMENT, MAKING
IT CRITICAL TO EVALUATE YOUR SPECIFIC NEEDS BEFORE MAKING A PURCHASE. THINKSTOCK
THE TASK, LOOKING BACK ON IT NOW, WAS PRETTY MUCH INSURMOUNTABLE—IMPOSSIBLE,
EVEN.
AS THE FORMER CO-CHAIR OF THE TOOL AND EQUIPMENT COMMITTEE FOR THE NATIONAL
AUTOMOTIVE SERVICE TASK FORCE (NASTF), DONNY SEYFER HEARD THE QUESTION ALL THE
TIME, FROM HIS FELLOW SHOP OWNERS, FROM REPAIR TECHNICIANS, EVERYONE: HOW DO YOU
PICK THE RIGHT SCAN TOOL?
SEEMED LIKE A SIMPLE QUESTION, HE THOUGHT, SIMPLE ENOUGH THAT NASTF SHOULD BE ABLE
TO PROVIDE A RESOUNDING, CLARIFYING ANSWER TO THE INDUSTRY.
SO, SEYFER’S TASK BECAME JUST THAT: CREATE A MATRIX THAT WOULD ALLOW SHOPS TO PICK
THE CORRECT SCAN TOOL BASED ON THEIR RESPECTIVE WORK-MIX NEEDS.
SEYFER FINISHED THE PROJECT IN 2012—OR, REALLY, HE SAYS, HE “ENDED” THE PROJECT.
“WE WERE AWARE OF IT GOING IN, BUT THE PROBLEM WAS THAT IT WAS ESSENTIALLY
IMPOSSIBLE TO EVER BE DONE WITH IT,” HE SAYS. “THERE ARE HUNDREDS OF TOOLS OUT THERE,
AND THEY’RE CHANGING ALL THE TIME WITH NEW UPDATES AND SOFTWARE. IT’S SOMETHING
THAT COULD NEVER BE FINISHED.”
Page 38
39. THE SCAN
TOOL MATRIX
THE MATRIX THAT SEYFER HELPED CREATE WITH NASTF, OFFICIALLY CALLED THE “VEHICLE
MANUFACTURER SERVICE INFORMATION MATRIX,” HELPS TO PROVIDE DETAILS ABOUT OEM
SERVICE INFORMATION, TOOLS AND TRAINING MATERIALS. IT CAN BE FOUND ON THE NASTF
WEBSITE.
STILL, SEYFER, OWNER OF SEYFER AUTOMOTIVE INC. IN WHEAT RIDGE, COLO., SAYS THAT IT’S
NECESSARY FOR EVERY SHOP TO GO THROUGH THEIR OWN SIMILAR PROCESS OF FINDING THE
CORRECT DIAGNOSTIC EQUIPMENT TO EFFECTIVELY REPAIR TODAY’S VEHICLES.
“HAVING [THE CORRECT DIAGNOSTIC SCAN TOOL] IS THE BIGGEST THING IN INCREASING
EFFICIENCY AND COMPETENCY—WHEN YOU HAVE THE RIGHT ONE,” HE SAYS. “AND, NOT HAVING
THE CORRECT ONE IS GOING TO BE YOUR BIGGEST HINDRANCE.
“VEHICLES TODAY HAVE SO MANY DIAGNOSTIC AND REFLASHING NEEDS, AND YOU’RE ONLY
GOING TO SEE MORE AND MORE.”
RESEARCHING AND PURCHASING SCAN TOOLS CAN FEEL LIKE A DAUNTING TASK, BUT, AS SEYFER
AND CARQUEST’S GEORGE LESNIAK HELP POINT OUT, THERE ARE SIMPLE STEPS EVERY SHOP
CAN GO THROUGH TO ENSURE IT EQUIPS ITS TECHNICIANS WITH THE RIGHT DIAGNOSTIC
EQUIPMENT.
TEACH A TECH TO FISH: THE CHALLENGES
LESNIAK IS THE CURRICULUM DEVELOPMENT MANAGER FOR THE CARQUEST TECHNICAL
INSTITUTE. HE’S BEEN TEACHING AND WRITING COURSES FOR TECHNICIAN TRAINING FOR 14
YEARS, AND HE HAS PERSONALLY RUN THOROUGH TEST TRIALS ON THE PRODUCTS OF A
NUMBER OF AFTERMARKET AND OEM SCAN TOOL PROVIDERS.
HE KNOWS DIAGNOSTICS, AND HE SAYS THAT BEFORE ANY SHOP OWNER SEES A SCAN TOOL AS
A “SILVER BULLET” OR A “QUICK FIX” TO THEIR DIAGNOSTIC DILEMMAS, THEY NEED TO ASK
THEMSELVES ONE QUESTION: HOW MUCH TIME AM I WILLING TO INVEST IN LEARNING THE
ADVANCED FUNCTIONS OF THE SCAN TOOL I PURCHASE?
“TECHNICIANS WANT TO KNOW WHAT’S WRONG WITH THE VEHICLE THEY ARE TROUBLESHOOTING
TODAY,” HE SAYS. “THIS IS WHY SCAN TOOLS WITH BUILT-IN DIAGNOSTIC TIPS AND TRICKS ARE SO
POPULAR. I BELIEVE THIS IS A FUNDAMENTALLY WRONG APPROACH. REMEMBER THE OLD ADAGE,
‘IF YOU GIVE A MAN A FISH … .’ WELL, THE SAME HOLDS TRUE FOR TROUBLESHOOTING. IF YOU
GIVE THE TECHNICIAN AN ANSWER, HE MAY FIX A CAR BUT IF YOU TEACH A TECHNICIAN HOW THE
VEHICLE WORKS, HOW HIS DIAGNOSTIC EQUIPMENT WORKS AND HOW TO THINK FOR HIS OR
HERSELF, THEY CAN FIX NEARLY ANYTHING.”
BOTTOM LINE: A SCAN TOOL IS NOT A CRUTCH, LESNIAK SAYS, EVEN THOUGH MANY TECHNICIANS
AND SHOPS LIKE TO USE IT AS ONE.
AND THAT’S JUST ONE OF THE MANY CHALLENGES THAT THESE TOOLS PRESENT. HERE ARE
FOUR OTHERS SEYFER AND LESNIAK SAY TO KEEP IN MIND:
1. NO STANDARDIZATION. DESPITE THE PENDING CHANGES WITH RIGHT TO REPAIR LEGISLATION,
THERE IS NO UNIVERSAL, STANDARDIZED APPROACH TO DIAGNOSTICS RIGHT NOW, , SEYFER
SAYS. AND BECAUSE OF THAT, THE MAJORITY OF SCAN TOOLS OPERATE AND ROUTE THROUGH
THE VEHICLE’S COMPUTER SYSTEM DIFFERENTLY. THAT’S WHY CERTAIN SCAN TOOLS WORK—OR
EVEN PARTIALLY WORK—ON CERTAIN VEHICLES AND NOT ON OTHERS. IT’S ANOTHER REASON
TECHS NEED TO UNDERSTAND THE TOOL AND THE VEHICLE SYSTEM, LESNIAK SAYS.
Page 39
40. 2. REVERSE ENGINEERING. BECAUSE AFTERMARKET TOOL MAKERS ARE NOT GIVEN COMPLETE
VEHICLE INFORMATION, THEIR TOOLS MUST BE REVERSE ENGINEERED TO BE ABLE TO WORK,
AND THAT OFTEN CAN LEAD TO MISSED CAPABILITIES.
3. NOTHING IS UNIVERSAL—EVEN IF IT CLAIMS TO BE. ONE OF THE MOST DIFFICULT THINGS FOR
SHOPS IS TO WEIGH A TOOL’S CLAIMED ABILITY AGAINST ITS ACTUAL CAPABILITIES, SEYFER
SAYS. SIMPLY PUT: THERE IS NO ONE TOOL THAT CAN DO EVERYTHING FOR EVERY VEHICLE, OR
EVEN COME CLOSE. AND THAT BRINGS US TO ...
4. INFORMATION GAPS. WHETHER IT’S BECAUSE OF REVERSE ENGINEERING OR EVEN SIMPLY
NOT BEING THE LATEST VERSION OF A TOOL, THE EQUIPMENT WILL HAVE INFORMATION GAPS.
THE PROBLEM IS, LESNIAK SAYS, A SCAN TOOL ONLY SHOWS YOU WHAT IT CAN DO, NOT WHAT IT
CAN’T—YET ANOTHER REASON TO UNDERSTAND THE VEHICLES YOU WORK ON, HE SAYS.
HUNTING FOR ANSWERS: CHOOSING YOUR TOOL
EVERY SHOP WILL HAVE DIFFERENT NEEDS AND USES FOR A SCAN TOOL, SEYFER SAYS, SO IT’S
CRITICAL TO IDENTIFY YOUR FACILITY’S SPECIFIC NEEDS FROM THE EQUIPMENT. HE AND LESNIAK
OUTLINED SIX STEPS FOR DOING THAT.
STEP 1: LOOK AT WHAT YOU WORK ON. TAKE A LOOK AT YOUR WORK MIX, SEYFER SAYS. WHAT
VEHICLES DO YOU WORK ON THE MOST? WHAT MAKES, MODELS AND YEARS DO YOU SEE MOST
OFTEN? “THE MORE SPECIFIC AND ‘SPECIALIZED’ YOU CAN BE WITH WHAT YOU WORK ON, THE
BETTER OFF YOU’LL BE,” HE SAYS. PICK YOUR 10 MOST WORKED-ON VEHICLES, LESNIAK SAYS,
AND FIGURE OUT YOUR NEEDS FOR THOSE.
STEP 2: LOOK AT WHAT YOU DON’T WORK ON. OF COURSE, A SCAN TOOL SHOULD BE ABLE TO
HELP YOU BRING IN ADDITIONAL VEHICLES, JOBS, REVENUE AND, ULTIMATELY, PROFITABILITY,
LESNIAK SAYS. “PEOPLE ASK ME ALL THE TIME, ‘WHAT SCAN TOOL SHOULD I GET?’” HE SAYS. “AND
MY FIRST RESPONSE IS ALWAYS ASKING THEM, ‘WHAT DON’T YOU WORK ON?’ THEN I ASK, ‘WHY?’
USUALLY, THAT HELPS YOU IDENTIFY VEHICLES IN YOUR AREA YOU’RE MISSING OUT ON. FOR AN
EXAMPLE, SEYFER AND HIS SHOP RECENTLY INVESTED IN EQUIPMENT TO PROPERLY DIAGNOSE
JAGUARS, AS HE SAW MANY IN HIS AREA AND VERY FEW SHOPS THAT WERE TAKING ADVANTAGE
OF IT.
STEP 3: RESEARCH THE TOOLS. HERE’S WHERE SHOPS OFTEN GET DISCOURAGED, LESNIAK
SAYS, BUT IF YOU HAVE THE PROPER APPROACH AND THE CORRECT VISION FOR YOUR SHOP’S
WORK MIX (STEPS 1 AND 2), THEN YOU’VE ALREADY NARROWED IT DOWN QUITE A BIT. THERE ARE
SIX THINGS TO CONSIDER:
COVERAGE. WHAT DATA DOES THE TOOL COME WITH? WHAT SUBSCRIPTIONS? WHAT VEHICLES
DO THOSE COVER? WHAT MAKES AND MODEL YEARS? SEYFER SAYS THAT, BECAUSE OF
CHANGES IN VEHICLE DESIGN AND CAPABILITIES, NOT EVEN OEM TOOLS COVER ALL OF THEIR
OWN VEHICLES. AND SOME ARE ABLE TO ACCESS MULTIPLE MANUFACTURERS. YOU NEED TO
FULLY UNDERSTAND WHAT EACH TOOL IS CAPABLE OF READING.
TRAINING/EASE OF USE. MOST AFTERMARKET TOOLS ARE EASY TO “PICK UP AND GO WITH,”
LESNIAK SAYS. OEM TOOLS OFTEN COME WITH A STEEPER LEARNING CURVE FOR FIRST-TIME
USERS. TRY TO GET A FEEL FOR THE TIME AND EFFORT IT WILL TAKE FOR YOUR STAFF TO
MASTER THE EQUIPMENT, AND WHAT TRAINING THE MANUFACTURER OR PROVIDER OFFERS.
COMPATIBILITY. SOME TOOLS CAN BE USED THROUGH A WINDOWS-BASED PC OR LAPTOP, AND
SEYFER SAYS THAT OFTEN MEANS ONE SINGLE TOOL CAN WORK WITH A NUMBER OF DIFFERENT
VERSIONS OF MANUFACTURER SOFTWARE TO PROVIDE A WIDE RANGE OF COVERAGE.
Page 40
41. TECHNICAL SUPPORT. SOME TOOL MAKERS AND VEHICLE MANUFACTURERS PROVIDE HOTLINES
OF SORTS TO CALL FOR ADDITIONAL INFORMATION OR FOR DIFFICULT DIAGNOSES. UNDERSTAND
WHAT EACH TOOL HAS TO OFFER.
UPGRADES/UPDATES. AS PER SEYFER’S DILEMMA WITH HIS NASTF MATRIX, TOOLS ARE
CONSTANTLY BEING UPGRADED AND UPDATED. HE SAYS TO RESEARCH THE COMPANIES YOU’RE
CONSIDERING AND SEE WHAT THEY OFFER IN TERMS OF UPGRADES—NOT JUST FOR THE
PURPOSE OF THE EQUIPMENT BUT ALSO TO SEE IF THEY CUT ANY DEALS ON UPDATING THE
TOOL.
COST. THERE’S GOING TO BE A LARGE DISCREPANCY IN PRICE BETWEEN TOOL MAKERS. THIS IS
WHY UNDERSTANDING YOUR WORK MIX IS IMPORTANT TO GRASP THE VALUE OF THE TOOL.
STEP 4: ANALYZE THE RETURN. THERE ARE A LOT OF WAYS TO TRY TO ANALYZE HOW VALUABLE
A SCAN TOOL IS IN A SHOP. SEYFER LIKES TO SORT OF LOW-BALL THE RETURN AND ONLY
COMPARE THE COST OF THE TOOL (INCLUDING SUBSCRIPTIONS AND UPGRADES) TO THE AMOUNT
OF MONEY HE MAKES ON DIAGNOSTIC CHARGES. OBVIOUSLY, HE SAYS, THAT DOESN’T TAKE INTO
ACCOUNT ANY IMPROVEMENTS IN EFFICIENCY, CAR COUNT, ETC. HE SAYS IT HELPS GIVE HIM AN
ABSOLUTE MINIMUM THAT CAN SERVE TO DIRECTLY PAY OFF THE TOOL.
STEP 5: DEMO THE TOOLS. LESNIAK SAYS TO BE WARY OF ANY COMPANY THAT ISN’T CONFIDENT
ENOUGH IN ITS PRODUCT TO LET YOU HAVE IT FOR A FULL, ON-YOUR-OWN TRIAL PERIOD.
“RECEIVING A DEMO FROM THEM IS NOT GOOD ENOUGH,” HE SAYS. “YOU NEED TO HAVE IT IN
YOUR TECHNICIAN’S HANDS AND LET THEM BE ABLE TO SEE ITS FULL CAPABILITIES ON YOUR
ACTUAL WORK MIX. TESTING THE TOOL ON YOUR OWN IS THE MOST IMPORTANT THING YOU CAN
DO TO MAKE THE CORRECT DECISION.”
STEP 6: IMPLEMENT THE TOOLS. ALTHOUGH THIS STEP MUST COME AFTER YOU SELECTED AND
PURCHASED A TOOL, IT WILL ALSO HELP TO CONFIRM YOUR DECISION. DON’T JUST SIMPLY BUY
DIAGNOSTIC EQUIPMENT AND HAND IT OFF TO THE TECHNICIAN. CREATE PROCESSES AND
SYSTEMS FOR YOUR SHOP TO USE IT CORRECTLY, SEYFER SAYS, AND MAKE SURE TO MARKET
YOUR CAPABILITIES.
KEEP IT SIMPLE
LESNIAK AND SEYFER BOTH FEEL THAT CHOOSING A SCAN TOOL FOR YOUR SHOP CAN BE A
DAUNTING TASK. THE IMPORTANT THING TO REMEMBER, SEYFER SAYS, IS THAT YOU NEED TO
FIND THE BEST FIT FOR YOUR BUSINESS—NOT JUST THE FLASHIEST, MOST EXPENSIVE
EQUIPMENT (OR THE MOST AFFORDABLE, FOR THAT MATTER).
GET AS MUCH INFORMATION AS YOU CAN, LESNIAK SAYS. TALK WITH OTHER SHOP OWNERS, TALK
WITH YOUR VENDORS, ASK ABOUT IT IN 20 GROUP MEETINGS, ASSOCIATION GATHERINGS, ON
MESSAGE BOARDS—ANYWHERE YOU CAN. THERE’S PLENTY OF INFORMATION ONLINE ABOUT
EACH TOOL AND IATN, THE EQUIPMENT AND TOOL INSTITUTE (ETI), NASTF AND OTHERS HAVE
DETAILED INFORMATION.
IN THE END, THOUGH, LESNIAK SAYS TO TRY TO MAKE THE PROCESS AS SIMPLE AS YOU CAN.
“THERE’S NO ONE ANSWER FOR ANY SHOP,” HE SAYS. “BUT, IF YOU DO YOUR RESEARCH AND
TEST THE [SCAN TOOLS] OUT BEFOREHAND, YOU CAN MAKE IT A WHOLE LOT EASIER ON
YOURSELF.”
Page 41
42. Gary Stamberger – Training Director
Magnaflow Exhaust Products
As promised from last month, more on OBD. Refer to our Website, Magnaflow.com for archived Bulletins.
(http://www.magnaflow.com/07techtips/techbulletins.asp)
Data Stream
Referred to as Current Data or Live Data, this information is available to the technician using a Scan Tool. The number of PIDS (Parameter Identification)
available at any given time will depend on a couple of different factors. The particular vehicle (Manufacturer) involved will have the greatest influence on the
amount of data available. Followed by the type of Scan Tool used and whether you are viewing the data on the Global OBD II side or Manufacture Specific, aka
Enhanced Mode. (Figure 1) Most Scan Tools will have options for viewing the data in different formats such as digital or graphing mode. Graphing can be
particularly useful when looking at Oxygen Sensor activity. (Figure 2) The data available will consist of inputs and outputs, calculated values and system status
information.
Viewing data and becoming proficient at recognizing problem areas is one of the skills we spoke of in last months Bulletin (TB-80016). Part of any training on a
particular tool is the repetitive process of using it over and over until you begin to recognize when certain data doesn’t look right. This process will then lead you
toward a problem area where further testing will reveal the fault. You can not recognize bad data until you have looked at enough good data. One item to be aware
of is the practice of substituting good data values for suspect ones. Due to something called Adaptive Strategy, when the PCM suspects that a particular input may
not be reporting accurately, it will substitute a known good value for that sensor and run the vehicle on learned values. This will only show up in Enhanced Mode
as Global OBD II will always display actual values. This should not deter you from viewing in Enhanced Mode. It has always been my practice to look at codes
and data in both modes.
FIGURE 1 FIGURE 2
Freeze Frame
Freeze frame is a “snap shot” of data taken when a code is set. This can be very valuable information as it allows the technician an opportunity to duplicate the
conditions under which the trouble code was recorded. The number of freeze frame events recorded and viewable by the technician will again depend on the
vehicle and scan tool being used. Early systems could only store one batch of information, if more than one code was recorded we would typically only be able to
view the Freeze Frame for the last code set. Changes in both OBD and Scan Tool technology have allowed us to have multiple sets of information available for
multiple codes set. One exception is that of Misfire. Misfire codes and subsequent data take precedent and will overwrite any previous freeze data stored. Be
aware that all freeze frame information is lost when codes are cleared.
On Board Diagnostics Part II
Bulletin TB-80017
December, 2009
Page 42