This document provides instructions for removing an engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, securing the engine hood with a lifting strap, removing mounting bolts, and carefully raising and removing the engine hood to access the engine. Proper safety procedures and equipment are emphasized.
New holland w80 c tier 4a (interim) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders. It provides information on maintenance and repair of components such as the engine, fuel tanks, drive shafts, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, steering, cab climate control, electrical systems, front loader and bucket, cab, and decals. The manual instructs technicians on proper procedures and use of special tools for repair work.
New holland w60 c zb tier 4b (final) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders W50C, W60C, W70C, and W80C. It contains instructions for repair and maintenance work to be performed only by qualified dealership personnel. The manual provides information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, and electrical systems of the loaders. Proper procedures are outlined for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging and welding.
New holland w50 c zb stage iiib compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland tx64 combine harvester service repair manualuujfjjskkdme
The document provides instructions for the reader to click on a link to access a complete manual without waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
New holland tk76 tractor service repair manualuujfjjskkdme
This document outlines sections and guidelines for a service manual covering tractor models TK65 through TK95. It lists 18 different sections for repairs and maintenance covering general guidelines, engines, transmissions, brakes, hydraulics, electrical systems and more. Safety protocols are provided, emphasizing the importance of only using original spare parts and tools for repairs.
New holland td5.95 tractor service repair manualuujfjjskkdme
This document is a service manual for tractor models TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, and TD5.115. It contains an introduction and safety rules section, followed by detailed sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork, and decals. The manual provides maintenance and repair instructions for authorized workshops and technicians.
New holland td4.90 f tractor service repair manualuujfjjskkdme
The document provides a service manual for removing the engine from a tractor. It lists 19 steps for disconnecting components like the battery, exhaust pipe, bonnet, front axle guard, propeller shaft, hydraulic lines, and electrical connections. Removing the engine allows access to components like the clutch and transmission for service.
New holland tc5060 combine harvesters service repair manualuujfjjskkdme
This document is a service manual for TC5060, TC5070, and TC5080 combine models. It contains sections covering the engine, transmission, front axle system, hydrostatic drive, brakes and controls, hydraulic systems, steering, cab climate control, electrical systems, attachments/headers, product feeding, threshing, separation, residue handling, cleaning, and crop storage/unloading. The manual provides technical specifications and instructions for servicing and repairing components in these various systems.
New holland w80 c tier 4a (interim) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders. It provides information on maintenance and repair of components such as the engine, fuel tanks, drive shafts, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, steering, cab climate control, electrical systems, front loader and bucket, cab, and decals. The manual instructs technicians on proper procedures and use of special tools for repair work.
New holland w60 c zb tier 4b (final) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders W50C, W60C, W70C, and W80C. It contains instructions for repair and maintenance work to be performed only by qualified dealership personnel. The manual provides information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, and electrical systems of the loaders. Proper procedures are outlined for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging and welding.
New holland w50 c zb stage iiib compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland tx64 combine harvester service repair manualuujfjjskkdme
The document provides instructions for the reader to click on a link to access a complete manual without waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
New holland tk76 tractor service repair manualuujfjjskkdme
This document outlines sections and guidelines for a service manual covering tractor models TK65 through TK95. It lists 18 different sections for repairs and maintenance covering general guidelines, engines, transmissions, brakes, hydraulics, electrical systems and more. Safety protocols are provided, emphasizing the importance of only using original spare parts and tools for repairs.
New holland td5.95 tractor service repair manualuujfjjskkdme
This document is a service manual for tractor models TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, and TD5.115. It contains an introduction and safety rules section, followed by detailed sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork, and decals. The manual provides maintenance and repair instructions for authorized workshops and technicians.
New holland td4.90 f tractor service repair manualuujfjjskkdme
The document provides a service manual for removing the engine from a tractor. It lists 19 steps for disconnecting components like the battery, exhaust pipe, bonnet, front axle guard, propeller shaft, hydraulic lines, and electrical connections. Removing the engine allows access to components like the clutch and transmission for service.
New holland tc5060 combine harvesters service repair manualuujfjjskkdme
This document is a service manual for TC5060, TC5070, and TC5080 combine models. It contains sections covering the engine, transmission, front axle system, hydrostatic drive, brakes and controls, hydraulic systems, steering, cab climate control, electrical systems, attachments/headers, product feeding, threshing, separation, residue handling, cleaning, and crop storage/unloading. The manual provides technical specifications and instructions for servicing and repairing components in these various systems.
New holland tc5050 hillside combine harvesters service repair manualuujfjjskkdme
This service manual provides information on servicing TC5040, TC5050, TC5060, TC5070, TC5080, and TC5080 Hillside combines. The manual is divided into sections covering the combines' distribution systems, power train, travelling systems, body and structure, tool positioning, and crop processing systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical, hydraulic, and electronic components.
New holland tc5050 combine harvesters service repair manualuujfjjskkdme
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New holland tc40 a tractor service repair manualuujfjjskkdme
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
New holland tc5.90 fpt nef tier 4 b combine harvesters service repair manualuujfjjskkdme
This document is a service manual for the TC5.80, TC5.90, and TC5.90 Hillside combine models. It contains introduc-
tory information and outlines the contents which include sections on the engine, transmission, axle systems, hydraulics,
brakes, electrical systems, attachments, feeding, threshing, separation, cleaning, storage/unloading, and other systems.
It provides repair and maintenance instructions for qualified personnel and warns that only approved parts should be
used.
New holland tc4.90 fpt nef tier 3 combine harvester service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, maintenance, and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. The sections are organized by functional area and component and include detailed diagrams, part numbers, and troubleshooting steps.
New holland t6090 power command tractor service repair manualuujfjjskkdme
The document is a service manual that provides technical specifications, descriptions of operation, and repair/maintenance procedures for the primary hydraulic power system on various tractor models. It includes information on the variable displacement hydraulic pump, charge pump, compensator, filters, and pressure testing procedures. The hydraulic pump section covers specifications, operation, component views, and procedures for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump.
New holland lb95 b backhoe loader service repair manualuujfjjskkdme
This document is a workshop manual for LB90.B-LB115.B loader backhoes. It contains sections on safety precautions, maintenance, technical specifications, torque converters, transmissions, and front axles. The manual provides information on repair procedures, component disassembly and assembly, specifications, hydraulic diagrams, and fault finding to aid in servicing the machine. It is comprised of two volumes, one covering the loader backhoe and one covering the engine.
New holland e245 c evo hydraulic excavator service repair manualuujfjjskkdme
This document is a service manual for the E215C EVO and E245C EVO hydraulic excavators. It contains information on servicing and repairing various systems of the excavators, including the engine, fuel system, cooling system, hydraulic systems, frames and ballasting, tracks and suspension, climate control, electrical systems, booms/dippers/buckets, cab/bodywork/decals. Safety precautions are provided throughout and personal protective equipment is required when servicing the machines. The manual contains sections on specific components and systems with part numbers and instructions for repair and maintenance.
New holland cx5.90 fpt nef 6 stage iv combine harvester service repair manualuujfjjskkdme
This document is a service manual for several combine models and their engines. It contains an introduction and table of contents that outlines the various systems covered in the manual, including the engine, transmission, axles, hydraulics, steering, climate control, electrical systems, attachments/headers, product feeding, and threshing. The manual provides part numbers and specifications to service and repair the components of the combines.
New holland cr9060 elevation combine harvesters service repair manualuujfjjskkdme
This document is a service manual that provides instructions and specifications for servicing various components of agricultural equipment, including the distribution systems, power systems, engine, transmission, axles, steering, braking, body, operator controls, crop processing functions, and protection systems. It outlines proper procedures for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging or welding to ensure repairs are completed correctly.
New holland b110 c stage iiib tractor loader backhoe service repair manualuujfjjskkdme
This document is a service manual for tractor loader backhoes models B100C, B100C LR, B100C TC, B110C, B110C TC, and B115C. It contains information on engine systems, transmission systems, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering systems, wheels, cab climate control, electrical systems, front loader and bucket systems, boom, dipper, and bucket systems, and machine shields and guards. The manual provides part numbers, replacement instructions, and troubleshooting information to service technicians for maintaining and repairing the equipment.
New holland b100 ctc stage iiib tractor loader backhoe service repair manualuujfjjskkdme
This document is a service manual for tractor loader backhoes models B100C, B100C LR, B100C TC, B110C, B110C TC, and B115C. It contains information on engine systems, transmission systems, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering systems, wheels, cab climate control, electrical systems, front loader and bucket systems, boom, dipper, and bucket systems, and machine shields and guards. The manual is intended to be used by qualified dealership personnel for repair and maintenance work on the equipment.
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualuujfjjskkdme
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and other parts. The counterweight is removed using lifting equipment attached to an eyebolt in the top. Fenders are removed using eyebolts in mount holes and lifting equipment. The hood assembly can be removed or pivoted out of the way for access. The hydraulic tank is removed after draining fluid and disconnecting hoses by lifting it using eyes attached to outer holes.
Hyster c008 (h370 c) forklift service repair manualuujfjjskkdme
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from the outlet side.
Hyster b187 (s50 xl) forklift service repair manualuujfjjskkdme
This document provides information about service repairs for lift truck models S40XL, S50XL, and S60XL. It describes the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It provides specifications for pump flow rates, relief pressures, and mast lifting speeds for the different models. The steering system operates by sending pressurized hydraulic fluid from the pump to the steering control unit, which directs the fluid to steer the truck by activating the steering cylinder.
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...uujfjjskkdme
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, including necessary tools and safety precautions. Components are to be kept clean and fluids contained to prevent damage and environmental issues.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...uujfjjskkdme
The document provides instructions for removing and installing various engine components on a 320-A excavator, including:
1) Removing and installing the turbocharger, exhaust manifold, air inlet heater, and inlet manifold. Detailed steps are given to remove gaskets and fasteners and position replacement parts.
2) Keeping all parts clean of contaminants is emphasized, as contaminants can cause rapid wear and damage.
3) Installation is generally the reverse of removal, checking for worn gaskets and tightening fasteners to the specified torques. References are provided to related removal and installation procedures.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...uujfjjskkdme
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It lists the required tools and outlines 7 steps to disassemble the valve, including removing bolts, seals, springs, and spool valves. Safety warnings are provided regarding relieving hydraulic pressure before disassembly and preventing contamination of hydraulic components.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...uujfjjskkdme
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uujfjjskkdme
This document provides installation instructions for auxiliary control valves on a 320C excavator in 3 steps:
1. Install the F1 and F4 auxiliary control valves together using existing mount bolts and connect hoses and electrical connections.
2. Connect pilot lines, electrical connectors, and tubes to both control valves and install panels and supports.
3. Install five pilot lines and covers to complete the installation.
New holland tc5050 hillside combine harvesters service repair manualuujfjjskkdme
This service manual provides information on servicing TC5040, TC5050, TC5060, TC5070, TC5080, and TC5080 Hillside combines. The manual is divided into sections covering the combines' distribution systems, power train, travelling systems, body and structure, tool positioning, and crop processing systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical, hydraulic, and electronic components.
New holland tc5050 combine harvesters service repair manualuujfjjskkdme
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New holland tc40 a tractor service repair manualuujfjjskkdme
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
New holland tc5.90 fpt nef tier 4 b combine harvesters service repair manualuujfjjskkdme
This document is a service manual for the TC5.80, TC5.90, and TC5.90 Hillside combine models. It contains introduc-
tory information and outlines the contents which include sections on the engine, transmission, axle systems, hydraulics,
brakes, electrical systems, attachments, feeding, threshing, separation, cleaning, storage/unloading, and other systems.
It provides repair and maintenance instructions for qualified personnel and warns that only approved parts should be
used.
New holland tc4.90 fpt nef tier 3 combine harvester service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, maintenance, and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. The sections are organized by functional area and component and include detailed diagrams, part numbers, and troubleshooting steps.
New holland t6090 power command tractor service repair manualuujfjjskkdme
The document is a service manual that provides technical specifications, descriptions of operation, and repair/maintenance procedures for the primary hydraulic power system on various tractor models. It includes information on the variable displacement hydraulic pump, charge pump, compensator, filters, and pressure testing procedures. The hydraulic pump section covers specifications, operation, component views, and procedures for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump.
New holland lb95 b backhoe loader service repair manualuujfjjskkdme
This document is a workshop manual for LB90.B-LB115.B loader backhoes. It contains sections on safety precautions, maintenance, technical specifications, torque converters, transmissions, and front axles. The manual provides information on repair procedures, component disassembly and assembly, specifications, hydraulic diagrams, and fault finding to aid in servicing the machine. It is comprised of two volumes, one covering the loader backhoe and one covering the engine.
New holland e245 c evo hydraulic excavator service repair manualuujfjjskkdme
This document is a service manual for the E215C EVO and E245C EVO hydraulic excavators. It contains information on servicing and repairing various systems of the excavators, including the engine, fuel system, cooling system, hydraulic systems, frames and ballasting, tracks and suspension, climate control, electrical systems, booms/dippers/buckets, cab/bodywork/decals. Safety precautions are provided throughout and personal protective equipment is required when servicing the machines. The manual contains sections on specific components and systems with part numbers and instructions for repair and maintenance.
New holland cx5.90 fpt nef 6 stage iv combine harvester service repair manualuujfjjskkdme
This document is a service manual for several combine models and their engines. It contains an introduction and table of contents that outlines the various systems covered in the manual, including the engine, transmission, axles, hydraulics, steering, climate control, electrical systems, attachments/headers, product feeding, and threshing. The manual provides part numbers and specifications to service and repair the components of the combines.
New holland cr9060 elevation combine harvesters service repair manualuujfjjskkdme
This document is a service manual that provides instructions and specifications for servicing various components of agricultural equipment, including the distribution systems, power systems, engine, transmission, axles, steering, braking, body, operator controls, crop processing functions, and protection systems. It outlines proper procedures for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging or welding to ensure repairs are completed correctly.
New holland b110 c stage iiib tractor loader backhoe service repair manualuujfjjskkdme
This document is a service manual for tractor loader backhoes models B100C, B100C LR, B100C TC, B110C, B110C TC, and B115C. It contains information on engine systems, transmission systems, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering systems, wheels, cab climate control, electrical systems, front loader and bucket systems, boom, dipper, and bucket systems, and machine shields and guards. The manual provides part numbers, replacement instructions, and troubleshooting information to service technicians for maintaining and repairing the equipment.
New holland b100 ctc stage iiib tractor loader backhoe service repair manualuujfjjskkdme
This document is a service manual for tractor loader backhoes models B100C, B100C LR, B100C TC, B110C, B110C TC, and B115C. It contains information on engine systems, transmission systems, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering systems, wheels, cab climate control, electrical systems, front loader and bucket systems, boom, dipper, and bucket systems, and machine shields and guards. The manual is intended to be used by qualified dealership personnel for repair and maintenance work on the equipment.
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualuujfjjskkdme
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and other parts. The counterweight is removed using lifting equipment attached to an eyebolt in the top. Fenders are removed using eyebolts in mount holes and lifting equipment. The hood assembly can be removed or pivoted out of the way for access. The hydraulic tank is removed after draining fluid and disconnecting hoses by lifting it using eyes attached to outer holes.
Hyster c008 (h370 c) forklift service repair manualuujfjjskkdme
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from the outlet side.
Hyster b187 (s50 xl) forklift service repair manualuujfjjskkdme
This document provides information about service repairs for lift truck models S40XL, S50XL, and S60XL. It describes the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It provides specifications for pump flow rates, relief pressures, and mast lifting speeds for the different models. The steering system operates by sending pressurized hydraulic fluid from the pump to the steering control unit, which directs the fluid to steer the truck by activating the steering cylinder.
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...uujfjjskkdme
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, including necessary tools and safety precautions. Components are to be kept clean and fluids contained to prevent damage and environmental issues.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...uujfjjskkdme
The document provides instructions for removing and installing various engine components on a 320-A excavator, including:
1) Removing and installing the turbocharger, exhaust manifold, air inlet heater, and inlet manifold. Detailed steps are given to remove gaskets and fasteners and position replacement parts.
2) Keeping all parts clean of contaminants is emphasized, as contaminants can cause rapid wear and damage.
3) Installation is generally the reverse of removal, checking for worn gaskets and tightening fasteners to the specified torques. References are provided to related removal and installation procedures.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...uujfjjskkdme
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It lists the required tools and outlines 7 steps to disassemble the valve, including removing bolts, seals, springs, and spool valves. Safety warnings are provided regarding relieving hydraulic pressure before disassembly and preventing contamination of hydraulic components.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...uujfjjskkdme
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uujfjjskkdme
This document provides installation instructions for auxiliary control valves on a 320C excavator in 3 steps:
1. Install the F1 and F4 auxiliary control valves together using existing mount bolts and connect hoses and electrical connections.
2. Connect pilot lines, electrical connectors, and tubes to both control valves and install panels and supports.
3. Install five pilot lines and covers to complete the installation.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
6. INTRODUCTION
Basic instructions - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The information in this manual is up-to-date at the date of the publication. It is the policy of the manufacturer for
continuous improvement. Some information could not be updated due to modifications of a technical or commercial
type, or changes to the laws and regulations of different countries.
In case of questions, refer to your NEW HOLLAND CONSTRUCTION Sales and Service Networks.
47768541B 27/03/2015
3
7. INTRODUCTION
Basic instructions - Shop and assembly
Shimming
For each adjustment operation, select adjusting shims and measure the adjusting shims individually using a microm-
eter, then add up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or
the rated value shown on each shim.
Rotating shaft seals
For correct rotating shaft seal installation, proceed as follows:
1. Before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.
2. Thoroughly clean the shaft and check that the working surface on the shaft is not damaged.
3. Position the sealing lip facing the fluid.
NOTE: With hydrodynamic lips, take into consideration the shaft rotation direction and position the grooves so that
they will move the fluid towards the inner side of the seal.
4. Coat the sealing lip with a thin layer of lubricant (use oil rather than grease). Fill the gap between the sealing lip
and the dust lip on double lip seals with grease.
5. Insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a
hammer or mallet.
6. While you insert the seal, check that the seal is perpendicular to the seat. When the seal settles, make sure that
the seal makes contact with the thrust element, if required.
7. To prevent damage to the seal lip on the shaft, position a protective guard during installation operations.
O-ring seals
Lubricate the O-ring seals before you insert them in the seats. This will prevent the O-ring seals from overturning and
twisting, which would jeopardize sealing efficiency.
Sealing compounds
Apply a sealing compound on the mating surfaces when specified by the procedure. Before you apply the sealing
compound, prepare the surfaces as directed by the product container.
Spare parts
Only use CNH Original Parts or NEW HOLLAND CONSTRUCTION Original Parts.
Only genuine spare parts guarantee the same quality, duration, and safety as original parts, as they are the same
parts that are assembled during standard production. Only CNH Original Parts or NEW HOLLAND CONSTRUCTION
Original Parts can offer this guarantee.
When ordering spare parts, always provide the following information:
• Machine model (commercial name) and Product Identification Number (PIN)
• Part number of the ordered part, which can be found in the parts catalog
47768541B 27/03/2015
4
8. INTRODUCTION
Protecting the electronic and/or electrical systems during charging and welding
To avoid damage to the electronic and/or electrical systems, always observe the following practices:
1. Never make or break any of the charging circuit connections when the engine is running, including the battery
connections.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the machine or on any machine
attachment.
• Position the welder ground clamp as close to the welding area as possible.
• If you weld in close proximity to a computer module, then you should remove the module from the machine.
• Never allow welding cables to lie on, near, or across any electrical wiring or electronic component while you
weld.
4. Always disconnect the negative cable from the battery when charging the battery in the machine with a battery
charger.
NOTICE: If you must weld on the unit, you must disconnect the battery ground cable from the machine battery.
The electronic monitoring system and charging system will be damaged if this is not done.
5. Remove the battery ground cable. Reconnect the cable when you complete welding.
Special tools
WARNING
Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.
W0111A
The special tools that NEW HOLLAND CONSTRUCTION suggests and illustrate in this manual have been specifically
researched and designed for use with NEW HOLLAND CONSTRUCTION machines. The special tools are essential
for reliable repair operations. The special tools are accurately built and rigorously tested to offer efficient and long-
lasting operation.
By using these tools, repair personnel will benefit from:
• Operating in optimal technical conditions
• Obtaining the best results
• Saving time and effort
• Working in safe conditions
47768541B 27/03/2015
5
9. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47768541B 27/03/2015
6
10. INTRODUCTION
Personal safety
Carefully read this Manual before proceeding with main-
tenance, repairs, refuelling or other machine operations.
Repairs have to be carried out only by authorized and in-
structed staff; specific precautions have to be taken when
grinding, welding or when using mallets or heavy ham-
mers.
Not authorized persons are not allowed to repair or carry
out maintenance on this machine. Do not carry out any
work on the equipment without prior authorization.
Ask your employer about the safety instructions in force
and safety equipment.
Nobody should be allowed in the cab during machine
maintenance unless he is a qualified operator helping
with the maintenance work.
If it is necessary to move the equipment to carry out re-
pairs or maintenance, do not lift or lower the equipment
from any other position than the operator’s seat.
TULI12WEX2004AA 1
Never carry out any operation on the machine when the
engine is running, except when specifically indicated.
Stop the engine and ensure that all pressure is relieved
from hydraulic circuits before removing caps, covers,
valves, etc.
All repair and maintenance operations should be carried
out with the greatest care and attention.
Service stairs and platforms used in a workshop or in the
field should be built in compliance with the safety rules in
force.
Any functional disorders, especially those affecting the
safety of the machine, should therefore be rectified im-
mediately.
DANGER
Unexpected movement!
Make sure parking brake is applied. Secure
machine with wheel chocks.
Failure to comply will result in death or serious
injury.
D0013A
TULI12WEX2005AA 2
Before performing any work on the machine, attach a
maintenance in progress tag. This tag can be applied on
the left-hand control lever, safety lever or cab door.
47768541B 27/03/2015
7
11. INTRODUCTION
Product identification - Machine components
LEIL14CWL0054FB 1
1. Cab door and hand holds 5. Roll Over Protection Structure (ROPS) and Falling
Objects Protective Structure (FOPS) cab
2. Steps 6. Boom cylinder
3. Fuel tank access) 7. Loader lift arms
4. Engine hood 8. Cab air filter access
47768541B 27/03/2015
17
14. Engine - Engine and crankcase
Engine - Remove
NOTE: Emissions sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that gen-
erate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors. Avoid
using these tools during any service procedure in close proximity of emission sensors. If the use of these tools cannot
be avoided, remove the sensors using extreme caution prior to performing any service procedure.
1. Park the machine on firm, level ground, lower the
bucket/attachment to the ground.
Drive the machine into such a position that the bores
of the holders are aligned one above the other. Then
secure with the pin (arrow). The pin is located inside
the support on the frame.
Stop the engine.
LEIL14CWL0005AB 1
2. Keep all non-authorized personnel clear of the ma-
chine. Turn the ignition switch key to the “ON” position.
3. Move the joystick slowly forward and backward and
from the right-hand to the left-hand approximately a
dozen times. Turn the ignition key to the OFF position.
Pump brakes approximately 30 times to bleed accumu-
lators. Bleed ride control accumulator (if equipped) with
bleed screw.
NOTE: before carrying out any service work on the hy-
draulic system, it is necessary to allow the system to cool:
the temperature should not be more than 40 °C (104.0 °F).
LEIL14CWL0003AB 2
4. Open the outer panel to access the battery main switch.
The battery main switch box is located on the right-hand
side of the machine, below the operator’s compart-
ment.
LEIL14CWL0015AB 3
47768541B 27/03/2015
10.1 [10.001] / 3
15. Engine - Engine and crankcase
5. Put the battery main switch (1) in the OFF position.
LEIL14CWL0017AA 4
6. Disconnect the wiring harness (X-228) and (X-229)
from the engine air filter.
Disconnect the wiring harness (X-106) from the air tem-
perature sensor.
LEIL14CWL0171AB 5
Versions with air conditioning
1. Drain the air conditioning system and disconnect the
fan electrical connector (1).
Tag and disconnect the condenser hoses (2) and (3).
LEIL14CWL0159A 6
2. Remove the two lower bolts (1) of the condenser
bracket (2).
LEIL14CWL0160AB 7
47768541B 27/03/2015
10.1 [10.001] / 4
16. Engine - Engine and crankcase
3. Remove the two upper bolts (1) of the condenser.
Remove the condenser (2).
LEIL14CWL0161AB 8
All versions
1. Secure the engine hood (1) with the nylon llifting strap.
LEIL14CWL0216AB 9
2. Have another person to balance the hood and remove
the hood hinge mounting bolts (arrows) from the ma-
chine structure.
Carefully raise and remove the engine hood (1) from
loader. Lower the engine hood onto suitable platform
and disconnect lifting equipment.
LEIL14CWL0162AB 10
3. Tag and disconnect the left rear light connector (1).
Repeat this operation for the right rear light connector.
LEIL14CWL0163AB 11
47768541B 27/03/2015
10.1 [10.001] / 5
17. Engine - Engine and crankcase
4. Tag and disconnect the water in fuel wiring harness
(X-105).
Tag and disconnect the backup alarm wiring harness
(X-064).
Tag and disconnect the filter pressure switch wiring har-
ness (X-227). Cut the ties cable (1).
LEIL14CWL0173AB 12
5. Remove the four mounting bolts (1) of the right grid (2).
Remove the right grid (2).
NOTE: repeat the same operation on the left side.
LEIL14CWL0217AB 13
6. Connect suitable lifting equipment to counterweight (re-
fer to Couterweight – Remove).
Remove the six bolts (arrows) of the counterweight and
remove it.
LEIL14CWL0164AB 14
7. Slowly extract the counterweight (1) from rear chassis.
Be sure all wire harness connections have been dis-
connected.
Remove the counterweight (1) from the machine.
Lower the counterweight onto suitable platform and dis-
connect the lifting equipment.
LEIL14CWL0218AB 15
47768541B 27/03/2015
10.1 [10.001] / 6
18. Engine - Engine and crankcase
8. Remove the cap from the hydraulic tank (2).
Insert, into the hole, the hose (1) connected to a suction
pump and suck the oil from the tank (2).
NOTE: use a suitable container for collection of coolant and
abide by all local environmental laws for proper handling
and disposal.
LEIL14CWL0219AB 16
9. Loosen the clamp (2) on the coolant hose (1) and dis-
connect it from the radiator.
NOTE: use a suitable container for collection of coolant and
abide by all local environmental laws for proper handling
and disposal.
10. Unscrew the fitting and disconnect the hydraulic oil
hose (3) from the radiator.
LEIL14CWL0232AB 17
11. Loosen the clamp (1) and disconnect the coolant hose
(2) from the radiator.
Unscrew the fitting and disconnect the hydraulic oil
hose (3) from the radiator.
LEIL14CWL0233AB 18
12. Remove the screws (1) securing the clamps of the
hydraulic oil hose (2).
LEIL14CWL0234AB 19
47768541B 27/03/2015
10.1 [10.001] / 7
19. Engine - Engine and crankcase
13. Remove the four screws (1) to remove the fan guard
(2).
LEIL14CWL0469AB 20
14. Loosen the nut (3) to unscrew the fan (4).
The nut (3) is left-handed: turn the nut (3) clockwise
in respect to the engine to loosen the nut (3).
LEIL14CWL0456AB 21
15. Lean the fan (4) against the radiator group (5).
LEIL14CWL0457AB 22
16. Remove the screw (1) and disconnect the earth strap
(2) from the engine.
LEIL14CWL0170AB 23
47768541B 27/03/2015
10.1 [10.001] / 8
20. Engine - Engine and crankcase
17. Loosen the clamp (1) and disconnect the oil steam
recovery hose (2).
LEIL14CWL0220AB 24
18. Loosen the clamp (1) and disconnect the air inlet hose
(4).
Remove the screws (2) from the bracket (3).
LEIL14CWL0221AB 25
19. Remove the screw (2) to release the air inlet hose (3)
from the clamp (1).
LEIL14CWL0222AB 26
20. Remove the screw (2) of the half guideway (3) for
positioning fuel hoses (1).
LEIL14CWL0223AB 27
47768541B 27/03/2015
10.1 [10.001] / 9
21. Engine - Engine and crankcase
21. Remove the screws (1) of the air filter bracket (2).
Remove the air filter assembly (3) with the air inlet
hose, the oil vapor recovery pipe and bracket with
O-ring.
LEIL14CWL0224AB 28
22. Disconnect the wiring harness (X-109) from the inter-
mediate connector signal.
Disconnect the wiring harness (X-110) from the inter-
mediate connector injector.
Disconnect the A/C clutch wiring harness (X-226)
(only air conditioning versions).
Remove the clamp (1) and cut the ties cable (2).
LEIL14CWL0172A 29
23. Behind the starter motor (1), remove the screw (3)
and disconnect the ground wiring harness (X-232),
(X-233) and (X-234).
Remove the ties cable (2).
LEIL14CWL0174AB 30
47768541B 27/03/2015
10.1 [10.001] / 10
22. Engine - Engine and crankcase
24. Fan condenser connector (X-056) has already been
disconnected when removing the condenser (only air
conditioning versions).
Disconnect reverse solenoid wiring harness (X-086).
Disconnect the forward solenoid wiring harness
(X-087).
Disconnect the exhaust gas temperature sensor
wiring harness (X-107) and (X-108).
Remove the ties cable (1).
LEIL14CWL0175BB 31
25. Remove the screws (1) securing the exhaust stack (2).
NOTE: the exhaust stack (2) must be removed after the
detachment of the PM-Cat system.
LEIL14CWL0225AB 32
26. Loosen the clamp (1) and disconnect the compensa-
tion hose (2) from the PM-Cat system (3).
LEIL14CWL0226AB 33
47768541B 27/03/2015
10.1 [10.001] / 11
23. Engine - Engine and crankcase
27. Remove the four screws (arrows) securing PM-Cat
system (1) of the frame.
Remove the PM-Cat system (1) from the machine.
Extract, from the bottom, the exhaust stack.
LEIL14CWL0227AB 34
28. Disconnect the lambda probe connector (2).
Loosen the clamp (1) and remove the compensation
hose (3) from the turbocharger (4).
LEIL14CWL0228AB 35
29. Acting from under the machine:
• turn off the tap (1);
• loosen the clamp (2) and disconnect the cab heat-
ing hose;
• open the tap (1) to drain the coolant from the engine
block.
NOTE: use a suitable container for collection of coolant and
abide by all local environmental laws for proper handling
and disposal.
LEIL14CWL0229AB 36
30. From the right side of the machine, loosen the clamp
(1) and disconnect the hose cab heating (2).
LEIL14CWL0230AB 37
47768541B 27/03/2015
10.1 [10.001] / 12
24. Engine - Engine and crankcase
31. Remove the screw (1) of the half guideway for posi-
tioning reverse hose (2) and forward hose (3).
LEIL14CWL0231AB 38
32. Tag and disconnect starter motor (Terminal 50) wiring
harness (X-061).
Tag and disconnect starter motor wiring harness
(X-062) and (X-063).
Tag and disconnect alternator battery cable (X-040).
Tag and disconnect alternator (D+) wiring harness
(X-041).
Unscrew the bolt (1) and remove the clamp (2).
Remove eventually clamps and cut the ties cable not
indicated.
LEIL14CWL0176BB 39
33. Disconnect the fuel line hose (1) from the fuel pre-filter
and fuel hose (2).
LEIL14CWL0177AB 40
47768541B 27/03/2015
10.1 [10.001] / 13
25. Engine - Engine and crankcase
34. Unscrew the hydraulic fitting (1), (2) and (3) and dis-
connect the hoses from the gear pump.
Unscrew the hydraulic fitting (5) and (6) and discon-
nect the hoses from the hydrostatic pump.
Remove the four screws and disconnect the pipe (4)
from the hydrostatic pump.
Unscrew the hydraulic fitting (7) and disconnect the
pipe from the hydrostatic pump.
LEIL14CWL0178AB 41
35. Unscrew the hydraulic fitting (1) and disconnect the
hose from the hydrostatic pump.
Unscrew the hydraulic fitting (2) and disconnect the
pipe from the hydrostatic pump.
Remove the four screws and disconnect the pipe (4)
from the hydrostatic pump.
Remove the four screws and disconnect the pipe (3)
from the gear pump.
LEIL14CWL0179AB 42
36. For the models equipped with auxiliary pump (1), un-
screw the hydraulic fitting (2) and disconnect the hose
from the auxiliary pump.
LEIL14CWL0180AB 43
37. Connect suitable lifting equipment to engine lifting
brackets (arrows). Take up all slack in lifting equip-
ment.
LEIL14CWL0236AB 44
47768541B 27/03/2015
10.1 [10.001] / 14
26. Engine - Engine and crankcase
38. Remove the engine silent block (arrows) unscrewing
the nuts from the lower part of the engine.
Slowly raise engine from rear chassis. Be sure all wire
harness connections and hoses have been discon-
nected and are clear of the engine. Remove engine
from machine.
LEIL14CWL0235AB 45
47768541B 27/03/2015
10.1 [10.001] / 15
27. Engine - Engine and crankcase
Engine - Install
WARNING
Hot liquid under pressure!
Never remove the filler cap or the recovery tank cap while the engine is running or the coolant is hot.
Let the system cool. Turn the filler cap to the first notch and allow any pressure to escape, and then
remove the filler cap. Loosen the recovery tank cap slowly to allow any pressure to escape.
Failure to comply could result in death or serious injury.
W0296A
NOTE: Emission sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that gen-
erate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors. Avoid
using these tools during any service procedure in close proximity of emission sensors. If the use of these tools cannot
be avoided, remove the sensors using extreme prior to performing any service procedure.
1. Inspect the engine mounts. If the engine rubber isola-
tors require replacement, remove and discard the iso-
lators (1) and (2). Install new rubber isolator (2), then
rubber isolator (1).
Make sure that the tightening torque of the fixing screws
of the brackets to the engine is 118 - 133 N·m (87 - 98 lb
ft).
LEIL14CWL0393AB 1
2. Attach suitable lifting device to the engine and slowly
move it into position over the rear chassis. Be sure all
harness connections and hoses are out of the way or
positioned correctly for reconnecting, before lowering
engine.
Install the silent blocks (arrows) on the engine.
LEIL14CWL0235AB 2
3. Tighten the mounting bolts of the engine to a torque of
244 - 298 N·m (180 - 220 lb ft).
LEIL14CWL0394AB 3
47768541B 27/03/2015
10.1 [10.001] / 16
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. Engine - Engine and crankcase
4. Disconnect lifting equipment from the engine lifting
brackets.
LEIL14CWL0236AB 4
5. For the models equipped with auxiliary pump (1),
connect the hydraulic hose to the auxiliary pump and
tighten the fitting (2).
LEIL14CWL0180AB 5
6. Connect the hydraulic pipe (3) to the gear pump and
tighten the four screws on the half-shells.
Connect the hydraulic pipe (4) to the hydrostatic pump
and tighten the four screws on the half-shells.
Connect the hydraulic hoses to the hydrostatic pump
and tighten the fittings (1) and (2).
LEIL14CWL0179AB 6
7. Connect the hydraulic hoses to the gear pump and
tighten the fittings (1), (2) and (3).
Connect the hydraulic hoses to the hydrostatic pump
and tighten the fittings (5) and (6).
Connect the hydraulic pipe (4) to the hydrostatic pump
and tighten the four screws of the half-shells.
Connect the hydraulic pipe to the hydrostatic pump and
tighten the fitting (7).
LEIL14CWL0178AB 7
47768541B 27/03/2015
10.1 [10.001] / 17
30. Engine - Engine and crankcase
8. Connect the fuel line hose (1) to the fuel pre-filter and
fuel hose (2).
LEIL14CWL0177AB 8
9. Connect starter motor (Terminal 50) wiring harness
(X-061).
Connect starter motor wiring harness (X-062) and
(X-063).
Connect alternator battery cable (X-040).
Connect alternator (D+) wiring harness (X-041).
Install the clamp (2) and secure it with the bolt (1).
LEIL14CWL0176BB 9
10. Remove the screw (1) of the half guideway for posi-
tioning reverse hose (2) and forward hose (3).
Position the half guideway on the reverse hose (2) and
forward hose (3).
Tighten the screw (1) for blocking the hoses in cor-
rectly position.
LEIL14CWL0231AB 10
47768541B 27/03/2015
10.1 [10.001] / 18
31. Engine - Engine and crankcase
11. From the right side of the machine, connect the hose
cab heating (2) to the engine and secure the clamp
(1).
LEIL14CWL0230AB 11
12. Acting from under the machine:
• connect the cab heating hose and secure the clamp
(2);
• open the tap (1).
LEIL14CWL0229AB 12
13. Install the compensation hose (3) on the turbocharger
(4).
Tighten the collar (1).
Connect the lambda probe connector (2).
LEIL14CWL0228AB 13
14. Insert, from the bottom, the exhaust stack.
Install the PM-Cat system (1) on the machine. Tighten
the four screws (arrows) to secure the PM-Cat system
(1) to the frame.
NOTE: the exhaust stack must be positioned before the
installation of the PM-Cat system.
LEIL14CWL0227AB 14
47768541B 27/03/2015
10.1 [10.001] / 19
32. Engine - Engine and crankcase
15. Connect the compensation hose (2) to the PM-Cat
system (3).
Tighten the collar (1).
LEIL14CWL0226AB 15
16. Install the exhaust stack (2) on the PM-Cat system and
tighten the screws (1).
LEIL14CWL0225AB 16
17. Connect the exhaust gas temperature sensor wiring
harness (X-107) and (X-108).
Connect the forward solenoid wiring harness (X-087).
Connect reverse solenoid wiring harness (X-086).
Secure the wiring harness with the ties cable (1).
LEIL14CWL0175BB 17
47768541B 27/03/2015
10.1 [10.001] / 20
33. Engine - Engine and crankcase
Only air conditioning version
1. Fan condenser connector (X-056) must be connected
when installing the condenser.
2. Behind the starter motor (1), connect the ground wiring
harness (X-232), (X-233) and (X-234) and tighten the
screw (3).
Secure the ground wiring harness with the ties cable
(2).
LEIL14CWL0174AB 18
3. Connect the wiring harness (X-109) to the intermediate
connector signal.
Connect the wiring harness (X-110) to the intermediate
connector injector.
4. Connect the A/C clutch wiring harness (X-226)
Secure the wiring harness with the clamp (1) and the
ties cable (2).
LEIL14CWL0172A 19
5. Install on the engine the air filter assembly (3) with the
air inlet hose, the oil vapor recovery pipe and bracket
with O-ring.
Tighten the screws (1) of the air filter bracket (2).
LEIL14CWL0224AB 20
6. Install the half guideway (3) for positioning fuel hoses
(1).
Tighten the screw (2).
NOTICE: the nut (3) is left-handed: turn the nut (3) coun-
terclockwise in respect to the engine to tighten the nut (3).
7. Install the fan (4) and tighten the nut (3).
LEIL14CWL0223AB 21
47768541B 27/03/2015
10.1 [10.001] / 21
34. Engine - Engine and crankcase
8. Install the new O-ring on the bracket (3).
Connect the air inlet hose (4) and secure the clamp (1).
Install the bracket (3) on the engine and tighten the
screws (2).
LEIL14CWL0221AB 22
9. Connect the oil steam recovery hose (2) and secure the
clamp (1).
LEIL14CWL0220AB 23
10. Install the clamp (1) to secure the air inlet hose (3) and
tighten the screw (2).
LEIL14CWL0222AB 24
11. Connect the earth strap (2) to the engine and tighten
the screw (1).
LEIL14CWL0170AB 25
47768541B 27/03/2015
10.1 [10.001] / 22
35. Engine - Engine and crankcase
12. Install the fan guard (2) and tighten the four screws
(1).
LEIL14CWL0469AB 26
13. Connect the hydraulic oil hose (3) to the radiator upper
side and tighten the fitting.
Connect the coolant hose (2) to the radiator and se-
cure the clamp (1).
LEIL14CWL0233AB 27
14. Connect the hydraulic oil hose (3) to the radiator under
side and tighten the fitting.
Connect the coolant hose (1) to the radiator and se-
cure the clamp (2) .
LEIL14CWL0232AB 28
15. Secure the hydraulic oil hoses (2) with the clamps and
tighten the screws (1).
LEIL14CWL0234AB 29
47768541B 27/03/2015
10.1 [10.001] / 23