This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uujfjjskkdme
This document provides installation instructions for auxiliary control valves on a 320C excavator in 3 steps:
1. Install the F1 and F4 auxiliary control valves together using existing mount bolts and connect hoses and electrical connections.
2. Connect pilot lines, electrical connectors, and tubes to both control valves and install panels and supports.
3. Install five pilot lines and covers to complete the installation.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 904 b compact wheel loader (prefix b4l) service repair manual...uujjfjkkkdmme
This document provides instructions for disassembling the piston pump of a 904B compact wheel loader. It describes 33 steps to disassemble the various components of the pump, including removing plates, shafts, seals, springs, valves, and housings. Safety precautions are provided regarding the risks of high pressure hydraulic fluid and released spring forces. Tools required for the disassembly are also listed.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 336 f l excavator (prefix kcs) service repair manual (kcs0000...fjkskedmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and replacing gaskets and seals before reinstalling parts in the reverse order of removal. Safety precautions are provided regarding preventing contamination, allowing components to cool, and using approved lubricants.
Caterpillar cat 320 c excavator (prefix hkt) service repair manual (hkt00001 ...ujdfjjkskkmmde
This document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on a 320C excavator. It involves installing the control valves, connecting pilot lines and hoses, installing panels and filters, and filling the hydraulic system. Proper cleanliness and containment of fluids is emphasized. The process concludes by checking operation and taking an oil sample to test for contamination.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uujfjjskkdme
This document provides installation instructions for auxiliary control valves on a 320C excavator in 3 steps:
1. Install the F1 and F4 auxiliary control valves together using existing mount bolts and connect hoses and electrical connections.
2. Connect pilot lines, electrical connectors, and tubes to both control valves and install panels and supports.
3. Install five pilot lines and covers to complete the installation.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 904 b compact wheel loader (prefix b4l) service repair manual...uujjfjkkkdmme
This document provides instructions for disassembling the piston pump of a 904B compact wheel loader. It describes 33 steps to disassemble the various components of the pump, including removing plates, shafts, seals, springs, valves, and housings. Safety precautions are provided regarding the risks of high pressure hydraulic fluid and released spring forces. Tools required for the disassembly are also listed.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 336 f l excavator (prefix kcs) service repair manual (kcs0000...fjkskedmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and replacing gaskets and seals before reinstalling parts in the reverse order of removal. Safety precautions are provided regarding preventing contamination, allowing components to cool, and using approved lubricants.
Caterpillar cat 320 c excavator (prefix hkt) service repair manual (hkt00001 ...ujdfjjkskkmmde
This document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on a 320C excavator. It involves installing the control valves, connecting pilot lines and hoses, installing panels and filters, and filling the hydraulic system. Proper cleanliness and containment of fluids is emphasized. The process concludes by checking operation and taking an oil sample to test for contamination.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
New holland w80 c tier 4a (interim) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders. It provides information on maintenance and repair of components such as the engine, fuel tanks, drive shafts, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, steering, cab climate control, electrical systems, front loader and bucket, cab, and decals. The manual instructs technicians on proper procedures and use of special tools for repair work.
New holland w60 c zb tier 4b (final) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders W50C, W60C, W70C, and W80C. It contains instructions for repair and maintenance work to be performed only by qualified dealership personnel. The manual provides information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, and electrical systems of the loaders. Proper procedures are outlined for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging and welding.
New holland w60 c zb tier 4 compact wheel loader service repair manualuujfjjskkdme
This document provides instructions for removing an engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, securing the engine hood with a lifting strap, removing mounting bolts, and carefully raising and removing the engine hood to access the engine. Proper safety procedures and equipment are emphasized.
New holland w50 c zb stage iiib compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland tx64 combine harvester service repair manualuujfjjskkdme
The document provides instructions for the reader to click on a link to access a complete manual without waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
New holland tk76 tractor service repair manualuujfjjskkdme
This document outlines sections and guidelines for a service manual covering tractor models TK65 through TK95. It lists 18 different sections for repairs and maintenance covering general guidelines, engines, transmissions, brakes, hydraulics, electrical systems and more. Safety protocols are provided, emphasizing the importance of only using original spare parts and tools for repairs.
New holland td5.95 tractor service repair manualuujfjjskkdme
This document is a service manual for tractor models TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, and TD5.115. It contains an introduction and safety rules section, followed by detailed sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork, and decals. The manual provides maintenance and repair instructions for authorized workshops and technicians.
New holland td4.90 f tractor service repair manualuujfjjskkdme
The document provides a service manual for removing the engine from a tractor. It lists 19 steps for disconnecting components like the battery, exhaust pipe, bonnet, front axle guard, propeller shaft, hydraulic lines, and electrical connections. Removing the engine allows access to components like the clutch and transmission for service.
New holland tc5060 combine harvesters service repair manualuujfjjskkdme
This document is a service manual for TC5060, TC5070, and TC5080 combine models. It contains sections covering the engine, transmission, front axle system, hydrostatic drive, brakes and controls, hydraulic systems, steering, cab climate control, electrical systems, attachments/headers, product feeding, threshing, separation, residue handling, cleaning, and crop storage/unloading. The manual provides technical specifications and instructions for servicing and repairing components in these various systems.
New holland tc5050 hillside combine harvesters service repair manualuujfjjskkdme
This service manual provides information on servicing TC5040, TC5050, TC5060, TC5070, TC5080, and TC5080 Hillside combines. The manual is divided into sections covering the combines' distribution systems, power train, travelling systems, body and structure, tool positioning, and crop processing systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical, hydraulic, and electronic components.
New holland tc5050 combine harvesters service repair manualuujfjjskkdme
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New holland tc40 a tractor service repair manualuujfjjskkdme
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
New holland tc5.90 fpt nef tier 4 b combine harvesters service repair manualuujfjjskkdme
This document is a service manual for the TC5.80, TC5.90, and TC5.90 Hillside combine models. It contains introduc-
tory information and outlines the contents which include sections on the engine, transmission, axle systems, hydraulics,
brakes, electrical systems, attachments, feeding, threshing, separation, cleaning, storage/unloading, and other systems.
It provides repair and maintenance instructions for qualified personnel and warns that only approved parts should be
used.
New holland tc4.90 fpt nef tier 3 combine harvester service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, maintenance, and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. The sections are organized by functional area and component and include detailed diagrams, part numbers, and troubleshooting steps.
New holland t6090 power command tractor service repair manualuujfjjskkdme
The document is a service manual that provides technical specifications, descriptions of operation, and repair/maintenance procedures for the primary hydraulic power system on various tractor models. It includes information on the variable displacement hydraulic pump, charge pump, compensator, filters, and pressure testing procedures. The hydraulic pump section covers specifications, operation, component views, and procedures for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump.
New holland lb95 b backhoe loader service repair manualuujfjjskkdme
This document is a workshop manual for LB90.B-LB115.B loader backhoes. It contains sections on safety precautions, maintenance, technical specifications, torque converters, transmissions, and front axles. The manual provides information on repair procedures, component disassembly and assembly, specifications, hydraulic diagrams, and fault finding to aid in servicing the machine. It is comprised of two volumes, one covering the loader backhoe and one covering the engine.
New holland e245 c evo hydraulic excavator service repair manualuujfjjskkdme
This document is a service manual for the E215C EVO and E245C EVO hydraulic excavators. It contains information on servicing and repairing various systems of the excavators, including the engine, fuel system, cooling system, hydraulic systems, frames and ballasting, tracks and suspension, climate control, electrical systems, booms/dippers/buckets, cab/bodywork/decals. Safety precautions are provided throughout and personal protective equipment is required when servicing the machines. The manual contains sections on specific components and systems with part numbers and instructions for repair and maintenance.
New holland cx5.90 fpt nef 6 stage iv combine harvester service repair manualuujfjjskkdme
This document is a service manual for several combine models and their engines. It contains an introduction and table of contents that outlines the various systems covered in the manual, including the engine, transmission, axles, hydraulics, steering, climate control, electrical systems, attachments/headers, product feeding, and threshing. The manual provides part numbers and specifications to service and repair the components of the combines.
New holland cr9060 elevation combine harvesters service repair manualuujfjjskkdme
This document is a service manual that provides instructions and specifications for servicing various components of agricultural equipment, including the distribution systems, power systems, engine, transmission, axles, steering, braking, body, operator controls, crop processing functions, and protection systems. It outlines proper procedures for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging or welding to ensure repairs are completed correctly.
New holland b110 c stage iiib tractor loader backhoe service repair manualuujfjjskkdme
This document is a service manual for tractor loader backhoes models B100C, B100C LR, B100C TC, B110C, B110C TC, and B115C. It contains information on engine systems, transmission systems, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering systems, wheels, cab climate control, electrical systems, front loader and bucket systems, boom, dipper, and bucket systems, and machine shields and guards. The manual provides part numbers, replacement instructions, and troubleshooting information to service technicians for maintaining and repairing the equipment.
New holland w80 c tier 4a (interim) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders. It provides information on maintenance and repair of components such as the engine, fuel tanks, drive shafts, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, steering, cab climate control, electrical systems, front loader and bucket, cab, and decals. The manual instructs technicians on proper procedures and use of special tools for repair work.
New holland w60 c zb tier 4b (final) compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for New Holland compact wheel loaders W50C, W60C, W70C, and W80C. It contains instructions for repair and maintenance work to be performed only by qualified dealership personnel. The manual provides information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, and electrical systems of the loaders. Proper procedures are outlined for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging and welding.
New holland w60 c zb tier 4 compact wheel loader service repair manualuujfjjskkdme
This document provides instructions for removing an engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, securing the engine hood with a lifting strap, removing mounting bolts, and carefully raising and removing the engine hood to access the engine. Proper safety procedures and equipment are emphasized.
New holland w50 c zb stage iiib compact wheel loader service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland tx64 combine harvester service repair manualuujfjjskkdme
The document provides instructions for the reader to click on a link to access a complete manual without waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
New holland tk76 tractor service repair manualuujfjjskkdme
This document outlines sections and guidelines for a service manual covering tractor models TK65 through TK95. It lists 18 different sections for repairs and maintenance covering general guidelines, engines, transmissions, brakes, hydraulics, electrical systems and more. Safety protocols are provided, emphasizing the importance of only using original spare parts and tools for repairs.
New holland td5.95 tractor service repair manualuujfjjskkdme
This document is a service manual for tractor models TD5.65, TD5.75, TD5.85, TD5.95, TD5.105, and TD5.115. It contains an introduction and safety rules section, followed by detailed sections on the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform, cab, bodywork, and decals. The manual provides maintenance and repair instructions for authorized workshops and technicians.
New holland td4.90 f tractor service repair manualuujfjjskkdme
The document provides a service manual for removing the engine from a tractor. It lists 19 steps for disconnecting components like the battery, exhaust pipe, bonnet, front axle guard, propeller shaft, hydraulic lines, and electrical connections. Removing the engine allows access to components like the clutch and transmission for service.
New holland tc5060 combine harvesters service repair manualuujfjjskkdme
This document is a service manual for TC5060, TC5070, and TC5080 combine models. It contains sections covering the engine, transmission, front axle system, hydrostatic drive, brakes and controls, hydraulic systems, steering, cab climate control, electrical systems, attachments/headers, product feeding, threshing, separation, residue handling, cleaning, and crop storage/unloading. The manual provides technical specifications and instructions for servicing and repairing components in these various systems.
New holland tc5050 hillside combine harvesters service repair manualuujfjjskkdme
This service manual provides information on servicing TC5040, TC5050, TC5060, TC5070, TC5080, and TC5080 Hillside combines. The manual is divided into sections covering the combines' distribution systems, power train, travelling systems, body and structure, tool positioning, and crop processing systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical, hydraulic, and electronic components.
New holland tc5050 combine harvesters service repair manualuujfjjskkdme
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New holland tc40 a tractor service repair manualuujfjjskkdme
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
New holland tc5.90 fpt nef tier 4 b combine harvesters service repair manualuujfjjskkdme
This document is a service manual for the TC5.80, TC5.90, and TC5.90 Hillside combine models. It contains introduc-
tory information and outlines the contents which include sections on the engine, transmission, axle systems, hydraulics,
brakes, electrical systems, attachments, feeding, threshing, separation, cleaning, storage/unloading, and other systems.
It provides repair and maintenance instructions for qualified personnel and warns that only approved parts should be
used.
New holland tc4.90 fpt nef tier 3 combine harvester service repair manualuujfjjskkdme
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, maintenance, and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. The sections are organized by functional area and component and include detailed diagrams, part numbers, and troubleshooting steps.
New holland t6090 power command tractor service repair manualuujfjjskkdme
The document is a service manual that provides technical specifications, descriptions of operation, and repair/maintenance procedures for the primary hydraulic power system on various tractor models. It includes information on the variable displacement hydraulic pump, charge pump, compensator, filters, and pressure testing procedures. The hydraulic pump section covers specifications, operation, component views, and procedures for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump.
New holland lb95 b backhoe loader service repair manualuujfjjskkdme
This document is a workshop manual for LB90.B-LB115.B loader backhoes. It contains sections on safety precautions, maintenance, technical specifications, torque converters, transmissions, and front axles. The manual provides information on repair procedures, component disassembly and assembly, specifications, hydraulic diagrams, and fault finding to aid in servicing the machine. It is comprised of two volumes, one covering the loader backhoe and one covering the engine.
New holland e245 c evo hydraulic excavator service repair manualuujfjjskkdme
This document is a service manual for the E215C EVO and E245C EVO hydraulic excavators. It contains information on servicing and repairing various systems of the excavators, including the engine, fuel system, cooling system, hydraulic systems, frames and ballasting, tracks and suspension, climate control, electrical systems, booms/dippers/buckets, cab/bodywork/decals. Safety precautions are provided throughout and personal protective equipment is required when servicing the machines. The manual contains sections on specific components and systems with part numbers and instructions for repair and maintenance.
New holland cx5.90 fpt nef 6 stage iv combine harvester service repair manualuujfjjskkdme
This document is a service manual for several combine models and their engines. It contains an introduction and table of contents that outlines the various systems covered in the manual, including the engine, transmission, axles, hydraulics, steering, climate control, electrical systems, attachments/headers, product feeding, and threshing. The manual provides part numbers and specifications to service and repair the components of the combines.
New holland cr9060 elevation combine harvesters service repair manualuujfjjskkdme
This document is a service manual that provides instructions and specifications for servicing various components of agricultural equipment, including the distribution systems, power systems, engine, transmission, axles, steering, braking, body, operator controls, crop processing functions, and protection systems. It outlines proper procedures for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging or welding to ensure repairs are completed correctly.
New holland b110 c stage iiib tractor loader backhoe service repair manualuujfjjskkdme
This document is a service manual for tractor loader backhoes models B100C, B100C LR, B100C TC, B110C, B110C TC, and B115C. It contains information on engine systems, transmission systems, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering systems, wheels, cab climate control, electrical systems, front loader and bucket systems, boom, dipper, and bucket systems, and machine shields and guards. The manual provides part numbers, replacement instructions, and troubleshooting information to service technicians for maintaining and repairing the equipment.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BBL
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BBL00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01525672
Control Valve (Auxiliary) - Install - F1 and F4 Auxiliary
Control Valves
SMCS - 5051-012-AX
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) FT-2674 Vacuum Cap 1
(B) 138-7573 Link Bracket 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Install two hose assemblies on the bottom of the (F4) auxiliary control valve.
1/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g00704077
2. Fasten F1 and F4 auxiliary control valves together with the existing mount bolts. Fasten the
control valves at the top with a washer and nut (28), as shown.
3. Install the F1 and F4 auxiliary control valves.
4. Lower the F1 and F4 auxiliary control valves in order to connect the hoses and electrical
connections on the bottom of the auxiliary control valves.
Illustration 2 g00690963
5. Remove the cap to the hydraulic tank. Attach Tooling (A) to the hydraulic tank.
Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system.
This will minimize the leakage to the hose assemblies.
2/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 3 g00703894
6. Connect two pilot lines (30) to the bottom of each control valve.
Illustration 4 g00703965
7. Connect one electrical connector (29) to each control valve.
Illustration 5 g00703950
8. Align the auxiliary control valves with the main control valve. Install the bottom two mount
bolts (27).
3/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. 9. Remove nut (28) and the washer from the top two mount bolts that pass through control
valves (F1) and (F4).
10. Install the top two mount bolts.
11. Tighten the four mount bolts (27) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
12. Connect one electrical connector (26) to each control valve.
Illustration 6 g00703893
13. Remove 7X-2547 Bolt (25).
14. Remove Tooling (B) and the hoist. Install the original bolt (25).
Illustration 7 g00703941
15. Install bolts (23) in order to connect tube (24) to the (F1) control valve.
4/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Illustration 8 g00703888
16. Install bolts (21) in order to connect tube (22) to the (F4) control valve.
Illustration 9 g00703729
17. Install bolts (19) in order to connect tube (20) to the (F4) control valve.
18. Connect hose assembly (18) to the (F4) control valve.
5/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 10 g00703717
19. Connect hose assembly (17) to the (F1) control valve.
20. Connect two hose assemblies (16) to both control valves.
Illustration 11 g00703706
21. Connect three hose assemblies (15) to the (F1) control valve.
Illustration 12 g00703705
22. Install panels (14) and support (12).
23. Install the washers and bolts (13) that hold the panels and support together.
6/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 13 g00703703
24. Install air filter (10).
25. Install the washers and bolts (9) in order to hold the air filter and the support to the machine.
Illustration 14 g00703690
Illustration 15 g00703702
26. Install hose (6) and install two hose clamps (7).
7/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 16 g00703704
27. Connect two electrical connectors (11) to the air filter. Install a new tie strap.
Illustration 17 g00792422
28. Close side door (8).
Illustration 18 g00703510
(F1) Auxiliary control valve
(F4) Auxiliary control valve
29. Install five pilot lines (5).
8/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. 30. Remove Tooling (A).
31. Install high efficiency filters in place of the pilot filter, case drain filter, and the return filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
32. Fill the hydraulic oil tank and the swing drive with clean hydraulic oil to the correct level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Hydraulic System Oil Level -
Check" for the correct filling procedures.
33. Install the cap to the hydraulic tank.
34. Start the engine, and check the operation of the auxiliary attachments. Also, check for leaks.
Stop the engine.
35. Obtain a hydraulic oil sample from the main S·O·S port.
Reference: Refer to Operation and Maintenance Manual, "Sampling Interval and Location
of Sampling Valve" for the correct location.
36. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
Reference: Refer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
Illustration 19 g00703691
37. Install four bolts (4) and the washers in order to hold cover (3).
38. Install four bolts (2) and the washers in order to hold cover (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 10 22:08:01 UTC+0800 2019
9/9(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BBL
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BBL00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01974016
Control Valve (Auxiliary) - Assemble - F2 Auxiliary Control
Valve
SMCS - 5051-016-AX
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound
B 155-0695 Thread Lock Compound
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring. Use Tooling (A) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Spool, Load Hold Check Valve, and Line Relief Valves
1/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00713437
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install spring (57). Apply Tooling (B) to bolt (56). Install bolt (56). Tighten bolt (56) to
50 + 10 − 0 N·m (37 + 7 − 0 lb ft).
Illustration 2 g00713427
2. Install O-ring seals and backup rings in the line relief valves (42) and (44). Install O-ring
seals (49), (50), (52), (53), and (54). Install backup rings (51) and (55).
2/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 3 g00713419
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Assemble the load hold check valve. Install O-ring seal (47), spring (46), and check valve
(45) in plug (48).
Illustration 4 g00713411
4. Install O-ring seals (37), (38), (39), and (40) in the valve housing. Install spool (41). Install
line relief valves (42) and (44). Tighten line relief valves (42) and (44) to 95 ± 14 N·m
(70 ± 10 lb ft). Install load hold check valve (43). Tighten load hold check valve (43) to
200 ± 25 N·m (148 ± 18 lb ft).
Solenoid Valve and Housing
3/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 5 g00713324
1. Install O-ring seal (33) on plug (30). Install O-ring seal (34) on fitting (29). Install O-ring
seal (35) on plug (31). Install O-ring seal (36) on fitting (32).
Illustration 6 g00713323
2. Install fittings (29) and (32). Install plugs (30) and (31).
Illustration 7 g00713322
3. Install O-ring seal (24), (25), (26), and (27) on solenoid valve (22). Install O-ring seal (28)
on fitting (23).
4/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 8 g00713321
4. Install fitting (23). Install solenoid valve (22) in the housing. Install two bolts (21).
Illustration 9 g00713320
5. Install O-ring seal (20) in the valve housing.
Illustration 10 g00713319
6. Install valve (19). Install two bolts (18).
5/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 11 g00713318
7. Install O-ring seal (15) on fitting (12). Install O-ring seal (16) on fitting (14). Install O-ring
seal (17) on plug (13).
Illustration 12 g00713317
8. Install fitting (12), plug (13), and fitting (14).
Illustration 13 g00713316
9. Install O-ring seal (7) on fitting (6). Install O-ring seal (8), (9), (10), and (11) on solenoid
valve (5).
6/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Illustration 14 g00713315
10. Install fitting (6). Install solenoid valve (5) in the housing. Install two bolts (4).
Illustration 15 g00713314
11. Install O-ring seal (3) in the valve housing.
Illustration 16 g00713277
12. Install valve (1). Install two bolts (2).
End By:
7/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. a. Install the F2 auxiliary control valve. Refer to Disassembly and Assembly, "Control Valve
(Auxiliary) - Install" for the machine that is being serviced.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 10 22:07:00 UTC+0800 2019
8/8(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR BBL
Configuration: 320C, 320C L, 320C LN, 320C S Excavators BBL00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
320C Excavator Machine Systems
Media Number -RENR3826-16 Publication Date -01/11/2014 Date Updated -30/03/2016
i01974012
Control Valve (Auxiliary) - Assemble - F4 Auxiliary Control
Valve
SMCS - 5051-016-AX
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound
B 155-0695 Thread Lock Compound
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring. Use Tooling (A) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Spool and Load Hold Check Valve
1/10(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Illustration 1 g00705302
1. Install spring (73). Apply Tooling (B) to bolt (72). Install bolt (72). Tighten bolt (72) to
50 + 10 − 0 N·m (37 + 7 − 0 lb ft).
Illustration 2 g00705294
2. Install O-ring seal (70) and (71) on fitting (63).
Illustration 3 g00705452
2/10(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Assemble the load hold check valve. Install O-ring seal (68), spring (67), and check valve
(66) in plug (69).
Illustration 4 g00705280
4. Install O-ring seal (64) and (65) on fitting (61).
Illustration 5 g00705262
5. Install O-ring seals (56), (57), (58), and (59) in the valve housing. Install spool (60). Install
fittings (61) and (63). Tighten fittings (61) and (63) to 95 ± 14 N·m (70 ± 10 lb ft). Install
load hold check valve (62). Tighten load hold check valve (62) to 200 ± 25 N·m
(148 ± 18 lb ft).
Solenoid Valve and Housing
3/10(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Illustration 6 g00705245
1. Install O-ring seal (52) on plug (49). Install O-ring seal (53) on fitting (48). Install O-ring
seal (54) on plug (50). Install O-ring seal (55) on fitting (51).
Illustration 7 g00705243
2. Install fittings (48) and (51). Install plugs (49) and (50).
Illustration 8 g00705234
3. Install O-ring seal (43), (44), (45), and (46) on solenoid valve (41). Install O-ring seal (47)
on fitting (42).
4/10(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Illustration 9 g00705226
4. Install fitting (42). Install solenoid valve (41) in the housing. Install two bolts (40).
Illustration 10 g00705223
5. Install O-ring seal (39) in the valve housing.
Illustration 11 g00705216
6. Install valve (38). Install two bolts (37).
5/10(W)w
2019/10/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...