Máy lạnh Daikin âm trần

All rights reserved 10/15 SS
c
1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.
2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install
the outdoor unit close to the sea shore, contact your local distributor.
Cautions on product corrosion
Warning Ask a qualified installer or contractor to install this product. Do not try to install the product by yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.
Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or
contractor to install those parts and accessories. Use of unauthorised parts and accessories or
improper installation of parts and accessories can result in water or refrigerant leakage, electrical
shock, fire or explosion.
Read the user's manual carefully before using this product. The user's manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any enquiries, please contact your local importer, distributor and/or retailer.
Specifications, designs and other content appearing in this brochure are current as of October 2015 but subject to change without notice.
PCSAU1439A
Air Conditioning System
Air Conditioning System
HEAT PUMP [50Hz]
HEAT PUMP [50Hz]
Inverter series

2
Page 7
Page 11
Page 13
Page 15
Page 15
Page 7
Outdoor unit
Indoor unit
Outdoor unit
Outdoor unit
Indoor unit
CEILING SUSPENDED TYPE
WALL MOUNTED TYPE
FHQ71DAVMA
RZQS71AV1
FHQ100DAVMA FHQ125DAVMA FHQ140DAVMA
RZQS125AV1
RZQS100AV1 RZQS140AV1
RZQS125AY1
RZQS100AY1
FAQ71CVEA
RZQS71AV1
FAQ100CVEA
RZQS100AV1 RZQS100AY1
RZQS140AY1
1
Outdoor unit
Indoor unit
CEILING MOUNTED
CASSETTE TYPE
Round Flow
CEILING MOUNTED
CASSETTE TYPE
Round Flow
PRODUCT RANGE
Inverter series
FHQ60DAVMA
RZQS60AV1
FHQ50DAVMA
RZQS50AV1
FCQ71KAVEA
RZQS71AV1
FCQ60KAVEA
RZQS60AV1
FCQ50KAVEA
RZQS50AV1
RZQS60AV1
RZQS50AV1
OUTDOOR UNIT
RZQS71AV1 RZQS100AV1 RZQS100AY1
50 60
Series 71 100 125 140
FCQ100KAVEA FCQ125KAVEA FCQ140KAVEA
RZQS125AV1
RZQS125AY1
RZQS100AY1 RZQS140AY1
Outdoor unit
Indoor unit FCQ71KAVEA
RZQ71LV1
50 60
Series 71 100 125 140
RZQ125LV1
RZQ100LV1 RZQ140LV1
Outdoor unit
OUTDOOR UNIT
RZQ71LV1 RZQ100LV1 RZQ125LV1 RZQ140LV1
NEW NEW
NEW
NEW
NEW NEW

4
3
Night quiet operation function
3.94
4.26
4.02
COP is equal to capacity (kW) divided by power consumption (kW), and the larger the COP value, the higher
the energy efficiency, enabling cooling and heating with less electricity and increasing the energy saving
performance.
What is COP
(Coefficient of Performance)
CEILING MOUNTED
CASSETTE TYPE
Round Flow
Non-inverter
Inverter Time
Running
current
Starting
current
Time
Running
current
Current
Current
At startup, inverter raises frequency
smoothly, eliminating the starting
current spike.
Soft starter is
unnecessary, making
electrical installation
work much simpler.
At startup, full power is used to achieve the set temperature quickly.
Then, the capacity is adjusted according to the outdoor temperature
changes and subtle indoor load changes to achieve fine capacity control
resulting in a more stable room temperature.
Non-inverter type air
conditioners must be
switched on and off
repeatedly, causing
large fluctuations of the
room temperature.
Inverter performs variable control of frequency,
which determines air conditioner’s power performance.
Enhanced comfort with Inverter
Small temp.
difference
Cools a room
in less time
Cooling operation
Inverter power control
Non-inverter type air conditioner
Time
Temp
Set temp
Comfortable
Comfortable
Compact and lightweight
Compact and lightweight
50
53
46
49
RZQS71AV1
48 44
RZQS50/60AV1
49 45
RZQ71LV1
51 47
RZQ100/125LV1
54 50
RZQ140LV1
Sound pressure level3
(dB(A))
RZQS100AV1/Y1
54 50
RZQS125AV1/Y1
54 50
RZQS140AV1/Y1
Rated4
Night Quiet Mode
Energy Efficient
Energy Efficient
Note :
1
Rated cooling capacities are based on the
following conditions: Indoor temp., 27°CDB,
19.0°CWB; outdoor temp. 35°CDB, 24.0°CWB.
Equiv. refrigeration piping, 7.5 m (horizontal).
2
Rated heating capacities are based on the
following conditions: Indoor temp., 20°CDB,
outdoor temp., 7°CDB, 6°CWB. Equiv.
refrigeration piping, 7.5 m (horizontal)
COP
1
2
3
4
RZQS100AV1/Y1 RZQS125AV1/Y1 RZQS140AV1/Y1
Quiet operation
Quiet operation
Cooling
1
Cooling
1
Cooling
1
Heating
2
FCQ71KAVEA
RZQS71AV1
Cooling
1
Heating
2
Heating
2
FCQ60KAVEA
RZQS60AV1
Cooling
1
Heating
2
FCQ50KAVEA
RZQS50AV1
Cooling
1
Heating
2
Heating
2
Reducing noise will reduce capacity
slightly.
Complies with MEPS
Complies with MEPS
Wired Remote Controller
BRC1E62
Dot matrix display Large buttons and arrow keys
Clear Display Simple operation
Energy saving Convenience
Backlight display Guide on display
Weekly schedule
Setpoint range set
Setpoint auto reset
Off timer (programmed)
Multilingual display
"Nav Ease"
"Nav Ease"
3.85 3.89
3.18
4.46
4.05
3.89 3.65
The Automatic night quiet mode
will initiate 8 hours after the peak
temperature is reached in the
daytime, and normal operation
will resume 10 hours after that.
Note :
3
Anechoic chamber conversion value, measured according
to JIS parameters and criteria. During operation these
values are somewhat higher owing to ambient conditions.
4
Value when cooling. Value will differ when heating.
3.59
NEW
NEW
High COP models
COP
50
3.94 3.59 3.85 3.89 3.51 3.18
Cooling
4.26 4.02 4.46 4.05 3.89 3.65
Heating
3.48 3.38 3.28 3.23 3.15 3.04
Cooling
3.43 3.33 3.23 3.22 3.10 3.24
Heating
--- --- 3.18 3.13 --- ---
Cooling
--- --- 3.43 3.26 --- ---
Heating
CEILING MOUNTED CASSETTE TYPE
Round Flow
WALL MOUNTED TYPE
60 71 100 125 140
Achieved higher COP
Height 1,170 mm 990 mm
Weight 98 kg 75 kg
990
mm
Reduced installation
work thanks to light,
compact outdoor unit.
RZQ100LV1
RQ100LV1A
Reduced by
180 mm
Reduced by
23 kg
Inverter series
Inverter series
Inverter series
Inverter series
Inverter series
3.51
NEW

Carry-in and installation of units
Airtightness test
Vacuum drying
Test operation
Upgrade to air conditioners featuring the latest technology and enjoy greatly
improved energy efficiency.
Advanced technology including use of corrosion resistant EEV, acid neutralisers
and improved compressor reliability enables the re-use of existing piping*
without the need to flush the piping for a simplified replacement process.
Enables simplified air conditioner replacement with minimal impact on operations.
5 6
Reuse of existing piping
FHYC71KVE
φ9.5 φ15.9
φ9.5 φ15.9
RY71KV1
Cooling EER : 2.41 Heating COP : 2.55 Cooling EER : 3.51 Heating COP : 3.89
FCQ125KAVEA
RZQS125AV1
COP
Cooling Heating
4
3
2
1
2.41
3.51
2.55
3.89
*Only available with RZQS-A series.
When considering air conditioner replacement,
do the following things concern you?
For how long will the business have to close down?
While replacement work is going on, how will sales be affected?
How to minimize inconvenience to tenants, who only leave the
space vacant on weekends?
Won’t the costs be high and work period longer because scaffolding
is necessary for pipe replacement?
solved by Daikin!
Where feasible, by reusing existing pipes*, we cut your
work cost and reduce work time.
These
problems
are
Stronger refrigerating
machine oil
Highly corrosion resistant
electronic expansion valve
Highly reliable
compressor
Acid (chlorine ion)
Refrigerant pipe
Acid neutraliser
Particularly convenient in these circumstances
Piping
left as is
Upgrade
to new
indoor
unit
Upgrade to
compact
new outdoor
unit
An acid neutraliser agent is added to disable
acids (chlorine ions), which cause corrosion.
Refrigerant recovery and units removal Refrigerant recovery and units removal
Airtightness test
Vacuum drying
Test operation
Conventional
installation process
for replacement of
air conditioning
Installation process
for replacement
with
Quicker
installation
Quicker
installation
Filter or
Accumulator
Compressor
R22
7.1kW
class
R410A
12.5kW
class
For example, compared with R22 non-inverter units of 15 years ago, in the latest R410A
series some units use smaller diameter piping which means they can achieve greater
cooling capacity by reusing existing piping.
As a result, the greater capacity units ensure better performance to cope with the
increasing amount of heat generated by office equipment.
Normally, when you replace air conditioners, in addition to replacing indoor and
outdoor units, replacement of piping involves high costs and lengthy work periods.
And, the more installed units you have, the greater the cost for connecting them,
especially if they are installed in high places or embedded.
Leave it to Daikin! Since Daikin can carry out upgrades using your existing piping,
you can get the work done faster than ever before.
Reduces replacement time & cost by simplified installation
Enables Increased capacity & Higher EER/COP
Technology
Simplified Installation
Benefit1
Benefit2
46%
UP
53%
UP
Airtightness test
Vacuum drying
Test operation
Refrigerant recovery and units removal
If existing piping that can
be reused needs cleaning:
Quicker
installation
Quicker
installation
Installation of new piping
Quick
installation
thanks to
cleaning-free
pipe reuse
Removal of
existing piping
Reuse of
existing
piping Cleaning of piping
Connection of pipe cleaning machine
Removal of pipe cleaning machine
Pipes are buried and making new pipe installations difficult.
Outdoor unit difficult to access.
Multiple units are being upgraded at the same time.
NEW
Durability of compressor is improved
by adoption of filter or accumulator
to collect solid foreign substances.
*Strict conditions must be adhered to, please refer to the installation manual and Engineering Data Book for further details including pipe sizes
(if pipes are to be re-used)
*Strict conditions must be adhered to, please refer to the installation manual and Engineering Data Book for further details
including pipe sizes (if pipes are to be re-used)

8
Airflow
distribution
creates uniform
comfort throughout
the space.
Room remains
comfortable even
when set
temperature is
raised 1℃.
Comfort enhanced by Round Flow!
With uniform temperature
distribution Enhanced Comfort
Greater comfort
• Condition after exposure
to the smoke of 600
cigarettes in 1 m3
enclosed space.
Treated
surface
Untreated
surface
Grimy
surface
Resists
soiling
External panels are treated with a coating that helps to
repel dirt
Avoids uneven temperature and discomfort caused by drafts
To prevent dirt sticking to the
external panels, they have
been coated with a surface
treatment
As air flows out from corner outlets, comfort spreads more evenly.
360° airflow Air movement is gentle
with Round Flow
Helps prevents mould and
microorganisms growing out of the dust
and moisture that adheres to the filters.
Filter has anti-mould and
antibacterial treatment
Grime prevention and antibacterial coating: Makes cleaning easier
Adapts easily to the installation space
3-way flow
L-shaped
2-way flow
Opposite
2-way flow
(E.g., installed in
a corner)
(E.g., installed in
a long room)
(E.g., installed
near a wall)
(E.g., installed in
middle of ceiling)
4-way flow also possible.
All-round flow
360° airflow can
maintain comfort
even if air
discharge speed is
lower.
Typical flow patterns There are a total of 23 flow patterns.
Velocity decreases by
25% when set
temperature is raised
1℃ to 1.5℃.
Note: Whatever the discharge direction, the same type of panel is used. If installing for other than all-round flow, an air discharge outlet sealing material (option) must be used to
close each unused outlet.
Operation sound increases when using 2-way or 3-way flow.
A built-in antibacterial treatment that uses
silver ion in the drain pan prevents
the growth of slime, bacteria, and mould
that cause smells and clogging.
Condensation does not easily form on
and dirt does not cling to non-flocking
flaps.
It is easy to clean.
Non-flocking flaps
Silver ion anti-bacterial
drain pan
7
CEILING MOUNTED CASSETTE TYPE Round Flow
Cassette air conditioner with 360°
uniform airflow sets the standard
Cassette air conditioner with 360°
uniform airflow sets the standard
BRC7F634F
A signal receiver must be added to the indoor unit.
Wireless remote controller is supplied
in a set with a signal receiver.
Wireless LCD remote controller
Signal receiver unit
(Installed type)
Accessory required for indoor unit
Option
FCQ50/60/71/100/125/140KA
Heat pump
Note: Remote controller cable is not
included and must be procured
locally.
Wired LCD remote controller
BRC1E62
"Nav Ease"
"Nav Ease"

10
Easier to maintain
The condition of the drain pan and
drain water can be checked by
removing the drain plug and
suction grille
Drain plug
Just open the
suction grille!
Quick and easy to install
Just 256 mm high. Installable in tight
ceiling spaces (50–71KA)
Drain pump is
equipped as
standard
accessory with
850 mm lift
9
Unified square panels Compact body and quiet operation
Note:
1
Air direction is set to the standard position when the unit is shipped from the factory.
The position can be changed from the remote controller.
2
Closing of the corner discharge outlets is recommended.
Panel size is the same for all models, FCQ50-140KA.
It is easy to maintain a neat appearance when multiple
units are installed in the same room.
Optimal comfort and convenience
assured by 2 air discharge modes
Control of airflow rate has been improved from 2-step to 3-step.
Even in spaces with
high ceilings, a
comfortable airflow
is carried down to
the floor level.
Setting Setting
Standard
4.2
m
3.6
m
3.2
m
When all round flow is selected, ceilings up to 4.2 m in height can be
accommodated. (100-140KA)
Suitable for high ceilings
dB(A)
Sound pressure level
Same for
all models
Air direction
Auto air
direction control
Settable to 5 different
levels between 15° and 60°
Settable to 5 different
levels between 25° and 60°
Auto-swing between
15° and 60°
Auto-swing between
25° and 60°
Recommended for shops with
light coloured ceilings that
must be kept spotless.
Standard setting to
prevent draft.
Standard setting1
Setting to prevent soiling
of ceiling2
(field setting)
At heating startup and thermo OFF, air discharge
is automatically set to a near horizontal 25˚ or 30˚
to prevent direct exposure to cool air drafts.
Desired
situation
Auto-swing
5-levels
air direction
setting
Draft prevention
(In heating mode)
950 mm 950 m
m
256 mm *1 266 mm *2
*1 298 mm high with 100–140KA
*2 308 mm high with 100–140KA
All models can be installed without
using lifter because of the light weight
Transparent drain socket
Each corner of the
unit has an Adjuster
Pocket that lets you
easily adjust the
unit's suspended
height.
Note:
If the wireless remote
controller is installed, a signal
receiver unit is housed in one
of the adjuster pockets.
Since the orientation of
the suction grille can
be adjusted after
installing, the direction
of the suction grille
lines can be unified
when multiple units
are installed.
DIII-NET communication standard
Connection to a centralised control system
is available, no need for option card.
Easy height adjustment
Installed in any direction
The air direction is set automatically to the
memorised position of the previous air direction.
Switchable fan speed: High/Middle/Low
175 mm
850 mm
Low gas pressure detection
CEILING MOUNTED CASSETTE TYPE Round Flow
4-way
flow
3-way
flow
2-way
flow
4-way
flow
3-way
flow
2-way
flow
3.1 m
3.4 m
4.0 m
All round
flow
2.7 m
3.0 m
3.5 m
3.0 m
3.3 m
3.5 m
3.5 m
3.8 m
-
3.4 m
3.9 m
4.5 m
All round
flow
3.2 m
3.6 m
4.2 m
3.6 m
4.0 m
4.2 m
4.2 m
4.2 m
-
Standard
High ceiling
High ceiling
Criteria for ceiling height and number of air discharge outlets
Note: Factory settings are for standard ceiling height and all-round flow.
High ceiling settings (1) and (2) are set with the remote controller by field setting.
(Ceiling height is reference value)
50–71KA 100–140KA
Ceiling
height
Number of air discharge outlets used
Indoor unit
125KA
140KA
100KA
71KA
60KA
50KA
High
44
44
43
35
35
35
Middle
39
40
37.5
31.5
31.5
31.5
Low
34
36
32
28
28
28
Options required for specific operating environments
Filter chamber
High-efficiency filter
High-efficiency filter unit
Available in two types: 65% and 90% colorimetry.
Please use if you think the temperature and humidity
inside the ceiling exceeds 30°C and RH 80%,
respectively.
Insulation kit for high humidity
Using this kit, a duct can be
connected to take outdoor air
in.There are two chamber types
that have intake in two places: with
T-duct joint and without T-duct joint.
Fresh air intake kit
Panel spacer
Use when only minimal space is available between
drop ceilings and ceiling slabs.
Outside
Note: Some ceiling constructions may hinder installation.
Contact your Daikin Dealer before installing your unit.
40mm
Panel spacer
Sealing material of air discharge
outlet
Sealing material block air discharge openings not
used in 2-way or 3-way blow.
Branch duct
(direct-connection round duct)
A round duct can be attached without the need
for a chamber.
A flanged port for direct connection of a round
duct is provided. An existing branch duct chamber
can also be fitted (square slit hole).
1 Use of options will increase operating sound.
2 Connecting ducts, fan, insect nets, fire dampers, air filters, and other parts
should, as required, be procured locally.
3 When a local-procured fan is used, an interlock with air conditioner is
necessary.Optional PCB(KRP1C63)is required for interlocking.
4 It is recommended that the volume of outdoor air introduced through the kit is
limited to 10% of the maximum airflow rate of the indoor unit. Introducing higher
quantities will increase the operating sound and may also influence temperature
sending.
Note:
The units can be installed in the following different ways.
Intake duct
(procured locally)
Direct installation type
Chamber type (with T-duct joint)
KDDP55X160
KDDP55B160K
Chamber type (without T-duct joint) Note 3.4
Note 3.4
KDDP55B160
Intake duct
(procured locally)
(duct length: 4 m max.)
Connection
chamber
Suction
chamber
Connection
chamber
Suction
chamber
Top panel insulation(1)
Insulation for decoration panel
Side panel insulation
Suspension bracket insulation
Flexible duct
(procured locally)
T-duct joint
(procured locally)
Intake duct
(procured locally)
(duct length: 4 m max.)
Flexible duct
T-duct joint
Duct flange
(with insulation material)
Note 1.2
Two selectable temperature-sensors See page 21
See page 22
Hot start See page 21

12
Oil resistant grille
Note: Intended for use in salons, dining rooms, and ordinary sales floors, this specification
is not suitable for kitchens or other harsh environments.
Oil-resistant plastic is used for the air suction grille. This satisfies
durability in restaurants and other similar environments.
Comfortable
Flap neatly closes
when not in use.
The latest stylish
model
Indoor unit
High Low
71DA 38 34
100DA 42 34
125DA 44 37
Middle
Sound pressure level
36
50/60DA 37 32
35
38
41
140DA 46 38
42
Quiet operation dB(A)
The technology of the DC fan motor, wide
sirocco fan, and large heat exchanger
combine for greater airflow and quiet
operation
Sophisticated
design
White colour
Auto swing (up and down) and louvers
(left and right by hand) bring comfort to
the room
-
Suitable for high ceilings
Standard
High ceiling
50-71DA 100DA 125/140DA
2.7m or less 3.8m or less 4.3m or less
2.7m~3.5m 3.8m~4.3m
Note: Factory settings is “standard”.
“High ceiling” are set with remote controller by field setting.
3.5
m
50-71DA
4.3
m
100-140DA
Non-flocking flap
Easy maintenance
Easy-clean, flat surfaces
It is easy to wipe dirt off the flat side and lower surfaces of the unit.
Condensation does not easily form on and
dirt does not cling to non-flocking flap.
Non-flocking flap
Drain pump kit (option) includes a silver ion
antibacterial agent that assists in preventing
the growth of slime, bacteria, and mould that
cause smells and clogging
Drain pump kit
(built inside
the unit)
600
mm
Flexible installation
*Water used in the test-run can be drained from the air
discharge opening rather than from the side as was
formerly the case.
The unit fits more snugly
into tight spaces.
Drain pump kit (option) can
be easily incorporated
Drain pipe connection can be done
inside the unit. Refrigerant and drain
pipe outlets are at the same opening.
All wiring and internal servicing can be done
from under the unit
Installation flexibility for
freedom of design
Easier piping work for
rear side by removable
frame
Connection to a centralised control system is available, no need
for option card.
30 mm
or more
30 mm
or more
Programme "Dry" See page 21
Two selectable temperature-sensors
See page 21
11
FHQ50/60/71/100/125/140DA
Heat pump
Wireless remote controller is supplied in a
set with a signal receiver.
Signal receiver unit (Installed type)
locally.
BRC1E62
"Nav Ease"
"Nav Ease"
Comfortable airflow travels
throughout the room
Comfortable airflow travels
throughout the room
NEW
140CA BRC7GA53
Option
Louver manually adjusts for straight or
wide angle airflow

14
Comfortable
Maintenance possible from the front
of the unit
All maintenance tasks can be carried out via front
access. During servicing, attachment and detachment
of parts is easier.
Dehumidification is microprocessor controlled to prevent abrupt and
uncomfortable changes in air temperature.
Programme "Dry"
Comfort even on the far side of the room
To carry air to the far side of long
rooms, extra-high airflow adds 10%
more fan speed the "high" setting.
Air discharge setting is selected
from the remote controller by field
setting.
Auto swing (up and
down) and
wide-angle louvers
(left and right by
hand) facilitate
even room
temperature
6-direction
refrigerant piping
offers greater
installation
flexibility
Compact &
Sophisticated design
FAQ100
Flaps neatly close when not
in use
Fresh white colour
Design and
installation flexibility
Drain pump kit is available as option
Drain pump kit can be installed
on either left and right side of
the indoor unit.
Height of drain up
Drain pump kit
Indoor unit
Installs onto side of unit.
1,000 mm
Refrigerant
piping
1,200mm
340
mm
370mm shorter
9kg lighter
Height
FAQ100BV
360mm
Width 1,570mm
Weight 26kg
FAQ100C
340mm
1,200mm
17kg
Depth 200mm 240mm
Auto airflow rate (When BRC1E62 is used)
Easy cleaning
Removable and washable grille
Condensation does not easily form on and dirt does not
cling to non-flocking flaps.
Non-flocking flaps
Soft material
louver bends
airflow over a
wider area
Flat panel, easy to wipe dust off
Wide-angle
louvers
(by hand)
An air discharge
modes ensure
comfortable air
distribution across
the entire room
Auto-swing 5-level air direction setting
Gettable to 5
different levels
Connection to a centralised control system is available,
no need for option card.
Interlock control
As an energy saving feature, the room air conditioning
unit can be interlocked with the key card system.
Through 3rd party
building
management
system, it is
possible to
interlock air
conditioning and
lighting.
Interlock
13
WALL MOUNTED TYPE
FAQ71C
FAQ100C
FAQ71/100C
Compact design and
easy installation
Compact design and
easy installation
Wired LCD remote controller
Right pipe
Left pipe
Back-left pipe
Back-right pipe
Bottom-left pipe
Bottom-right pipe
BRC7EB518
Wireless remote controller is supplied in a
set with a signal receiver.
Signal receiver unit (Installed type)
"Nav Ease"
locally.
BRC1E62
"Nav Ease"
Option

The Aero Spiral Fan features fan blades with
the bent blade edges, further reducing
turbulence.
Aero Spiral Fan
Escaping eddies are sucked in by
the bent blade edges, reducing
overall turbulence.
The high efficiency compressor to
achieve a high COP
2
1
DC fan motor
Efficiency improved in all areas compared to AC
motors, especially at low speeds.
Sucked gas is compressed in
the scrolling part before the
heated motor, so that the
machine compress the
non-expanded gas, resulting in
high efficiency compression.
>> Scroll compressor
Energy savings is
realised, eliminating
the friction and the
leakage of
refrigerant gas.
>> Swing compressor
Compressor equiped with Reluctance DC motor
3 DC fan motor structure
With the bent
blade edge
Without the bent
blade edge
Reluctance
DC motor
Scroll section
Suction
Discharge Motor section
RZQS50-71A, RZQ71/100L
Technology for energy efficiency
Swing bushing
Refrigerant gas
Piston by incorporated
blade and roller.
Small load Large load
Low capacity High capacity
Reluctance DC Motor
DC motor
More than 20%
AC motor
Rotational speed
Motor
efficiency
Daikin DC Inverter models are equipped with the Reluctance DC
motor for compressor.
The Reluctance DC motor uses 2 different types of torque,
neodymium magnet*1 and reluctance torque*2.
This motor can save energy because it generates more power
with a smaller electric power than an AC or previous DC motor.
*1. A neodymium magnet is approximately 10
times stronger than a standard ferrite
magnet.
*2. The torque created by the change in power
between the iron and magnet parts.
Note: Data are based on studies conducted under
controlled conditions at a Daikin laboratory.
RZQS100-140A, RZQ125/140L
3
1
2
OUTDOOR UNIT
RZQS71AV1 RZQS100AV1/Y1
RZQS125AV1/Y1
RZQS140AV1/Y1
Easy installation and maintenance
Separation
available
-20
-10
0
10
20
30
40
50
Wide operation range
46˚C
DB
Cooling
-5˚C
DB
Outdoor temp(˚CWB)
Outdoor temp(˚CDB)
Heating
-15˚C
WB
15.5˚C
WB
Cooling is efficient even in winter
when indoor temperatures are higher
than those outside, such as in
underground public spaces or offices
with many computers.
If the refrigerant piping length does not
exceed 30 m, there is no need for on-site
gas charging.
(Applicable to RZQS100–140A and RZQ100–140L
outdoor units)
Operation range
Night time quiet operation function
Durability
Construction
Non-treated fin
Anti corrosion
treated fin
Aluminium
Aluminium
Corrosion resistant
resin
Hydrophilic treatment
8:00 12:00 16:00 20:00
Power
consumption
Time
Limitation
Demand Control
Function
* Required for KRP58M51 (Option)
RZQS50AV1
RZQS60AV1
Compact and light weight
50
53
46
49
RZQS71AV1
48 44
RZQS50/60AV1
Sound pressure level1
(dB(A))
RZQS100AV1/Y1
54 50
RZQS125AV1/Y1
54 50
RZQS140AV1/Y1
49 45
RZQ71LV1
51 47
RZQ100/125LV1
54 50
RZQ140LV1
Rated2 Night Quiet Mode
Reducing noise will reduce capacity slightly.
15 16
100
50
0
8:00
Peak in outdoor temperature
8 hours
Rated
10 hours
Quiet mode
Quiet mode
12:00 16:00 20:00 0:00 4:00 8:00
46
50
Capacity
(%)
Load
(%)
Operation
Sound
(dB(A))
Note : 3
In case of RZQS71AV1
Allowed refrigerant piping length and
level difference
Note :
1
Additional refrigerant charging is required if the
refrigerant pipe is longer than the length.
Max.
length
Max. level
difference
Pre
charged1 30 m
50 m
(Equivalent
length 70m)
30 m
75 m
(Equivalent
length 90m)
RZQS100-140A
RZQ100-140L
RZQS50-71A
RZQ71L
Inverter series
Height 1,170 mm 990 mm
Weight 98 kg 75 kg
990
mm
RZQ100LV1
RQ100LV1A
Reduced by
180 mm
Reduced by
23 kg
Note : 1
Anechoic chamber conversion value, measured according to JIS
parameters and criteria. During operation these values are
somewhat higher owing to ambient conditions.
2
Value when cooling. Value will differ when heating.
Inverter
series
Pre charged for up to 30 metres
75 m piping length
Reduced installation work
thanks to light, compact
outdoor unit.
The Automatic night quiet mode will initiate 8 hours after the peak temperature is reached in
the daytime, and normal operation will resume 10 hours after that.
The outer panel for the piping connection part
of the front, right side and backside can be
removed and is easier for post-installation
piping work.
4-direction piping offers greater
layout freedom
Removable part of
bottom frame makes
the piping work easier
A pump-down switch is provided to make it
easier to collect refrigerant if the unit is to be
moved or layout modified.
Facilitates pump down
(Refrigerant recovery function)
*Pump-down function is available for pre-charged refrigerant
amount.
Effective gas monitoring reduces the labor required
for operation, maintenance, and repairs.
Low gas pressure detection function
Suited for year-round
cooling applications
As the bottom frame is subject to
corrosion, a corrosion-proof galvarium
steel plate is adopted to enhance the
durability.
Heat exchange fins are provided with
anti-corrosion treatment
The maximum capacity is maintained
within a set level of power
consumption, which makes it possible
to keep a comfortable and effective
demand control.

SkyAir shares common control with the Heat
Reclaim Ventilator and other Daikin
air-conditioning units, thus simplifying interlocking
operations.
SkyAir
Indoor unit
LCD remote controller
for SkyAir indoor unit
Heat Reclaim
Ventilator
Interlocking
Interlocking
Convenience
Clear Display
Energy saving
REMOTE CONTROLLER Optional accessory
Easy-to-read LCD remote controller allows various system control configurations and control of multiple indoor units.
Remote controller options are shown on the page introducing each indoor unit model.
Wireless remote controller for each indoor unit type
WALL MOUNTED TYPE
Heat pump
LCD wireless remote controller
BRC7F634F
Note: The signal receiver unit shown in the photograph is for mounting inside the decoration panel of the
ceiling mounted cassette type.
The wireless remote controller is supplied in a set with a signal receiver.
Signal receiver unit is contained inside decoration panel or indoor unit.
Shape of signal receiver unit differs according to the indoor unit.
Signal receiver unit
(For ceiling mounted
cassette type)
BRC1E62
Wired Remote Controller "Nav Ease"
"Nav Ease"
18
17
The first period starts and the
air conditioner starts the cooling
operation.
College classroom sample (a summer Monday case)
1) 8:30 ON
ON OFF ON OFF
In the second period, the classroom
is unoccupied and the air conditioner
stops.
2) 10:00 OFF
When the third period starts,
operation starts again.
3) 13:00 ON
After the third period, the classroom
becomes vacant again and the
air conditioner stops.
4) 15:00 OFF
BRC7F634F
BRC7EB518
BRC7GA53
(English, German, French, Spanish, Italian, Portuguese, Greek, Dutch, Russian, Turkish, and Polish).
Multilingual display
Display is available in 11 languages.
Dot matrix display Backlight
display
A combination of fine dots
enables various icons.
Large text display is easy to
see.
Weekly schedule
- 5 actions per day can be scheduled for each day of the week.
- The holiday function will disable schedule timer for the days that have been set as
holiday.
- 3 independent schedules can be set. (e.g. summer, winter, mid-season)
Until now only the temperature for one point could be
set, but now the new remote controller (BRC1E62)
allows the setting of both Cooling and Heating, and with
the fan operation, mid-range temperatures are
comfortable andoperation is more energy efficient.
- Even if the set temperature is changed, it returns to
the preset temperature after a preset period of time.
- Period selectable from
30min/60min/90min/120min.
- Saves energy by limiting the min. and max. set
temperature.
- Avoids excessive heating or
cooling.
- This function is convenient when
the remote controller is installed
at a place where any number of
people may operate it.
NEW
This simple, contemporary remote controller with
fresh white colour matches your interior design.
The clear, backlight display with large
easy-to-read text makes navigation easy and
provides one-touch control over your in-home
comfort.
NEW
2 setpoints
Cooling / Heating
Heating
operation
20ºC 26ºC
Cooling
operation
Fan operation
Restaurant sample
Full tables at lunchtime
After 30 minutes*
Restaurant opened
Temperature is set to 27ºC
Then is lowered to 24ºC
for crowded room
Automatically returns to
preset temperature (27ºC)
*Setting possible for after 30, 60, 90,
and 120 minutes.
NEW
NEW
Setpoint range set
NEW Setpoint auto reset
Auto operation mode
- Sets and saves setting for an increment of time that
automatically turns off air conditioner after a preset period of
time for each time operation starts.
- Period can be preset from 30 to 180 minutes in10-minute increments.
Wireless remote controller
27°C
24°C
Returns to
27°C
automatically

Central remote controller
Easily adaptable to large-scale, high-function, centralised remote control system.
Centralised control, with a setting as
simple as it is with a standard
remote controller, of up to 64 groups
(1,024 indoor units) is possible.
DCS302CA61 (Option)
With its high functionality, the full
colour “all-in-one” graphic controller
facilitates management of SkyAir
System in a variety of ways.
DCS601C51 (Option)
Unified on/off controller
Centralised control of on/off by
group or all at once for up to 256
indoor units.
DCS301BA61 (Option)
Schedule timer
Unified control of weekly schedule
for up to 1,024 indoor units.
DST301BA61 (Option)
Schedule timer sets on/off time in 1 minute units
to be executed twice a day for a week at a time.
System variation to control multiple indoor units
Control by 1
remote controller
Control pattern Wired remote controller Wireless remote controller
Control by 2
remote controllers
Group control
Control by
external command
Centralised remote
control
Interlock control
with Heat Reclaim
Ventilator
(Basic system)
Link by remote
controller group control.
Zone link control by
centralised control.
For control from 2
locations such as in
room and control room,
exits, etc.
For simultaneous
control of up to 16
indoor units.
Centralised control of
up to 64 indoor groups
from remote location
up to 1 km away.
Signal receiver unit installed
on indoor unit
Heat Reclaim Ventilator for indoor units within a zone are operated by
interlocking. Can also be operated independently by remote controller.
Central remote controller (option)
Heat Reclaim
Ventilator
Can be operated simultaneously
or independently by remote controller
(set by ventilation mode)
Heat Reclaim
Ventilator
Non-polar, double-core
(max. wiring length 500 m)
Connects 2 wired remote
controllers (See note 1)
Automatic address setting function Automatic address setting function
Signal receiver unit installed
on 1 indoor unit
Optional wiring adaptor for
electrical appendices is necessary
Can be operated simultaneously
by remote controller
(set by ventilation mode)
Heat Reclaim
Ventilator
Heat Reclaim Ventilator for indoor units within
a zone are operated by interlocking
Central remote controller (option)
Heat Reclaim
Ventilator
Operation and monitoring
is carried out using the
contact signal from the
operation control box in
the monitoring room. Optional wiring adaptor for
electrical appendices is necessary
Note:1
BRC1E62 can connect to BRC1E62 only. 2
It is not possible to use two wireless remote controllers. 3
BRC1E62 cannot connect to wireless remote controller.
Central remote controller (option) Central remote controller (option)
Not possible
(See note 2, 3)
(Command from outside) (Command from outside)
Functions
overview
Functions
overview
FUNCTIONS
Cooling only
Work &
servicing
REMOTE CONTROLLER Optional accessory
19 20
*1 : Applicable when wired remote controller is used
*2 : For outdoor units
*3 : Applicable when BRC1E62 is used
*4 : Installable on max. 3.5 m(50-71) and 4.3 m (100-140) high ceiling
*5 : Option
Note:
FCQ50-140KAVEA FHQ50-140DAVMA
RZQS50-140AV1
RZQS100-140AY1
FAQ71/100CVEA
RZQS71/100AV1
RZQS100AY1
Indoor unit
Outdoor unit
Comfort
Cleanliness
Remote
Controller
Control
features
Options
Others
CEILING SUSPENDED TYPE WALL MOUNTED TYPE
CEILING MOUNTED
CASSETTE TYPE
Round Flow
Auto swing
Swing pattern selection
DC fan mortor (Indoor unit)
Switchable fan speed
Programme “Dry”
High ceiling application
Two selectable temperature-sensors *1
Setpoint auto reset *3
Setpoint range set *3
Weekly schedule timer *3
Off timer (programmed) *3
Anti-bacterial air filter
Drain pump mechanism
Pre-charged for up to 30 m *2
Filter sign
Ceiling soiling prevention
Auto-restart
Control by 2 remote controllers
Group control by 1 remote controller
External command control
Central remote control
Interlock control with Heat Reclaim Ventilator
Anti corrosion treated heat exchangers *2
Draft prevention function (heating)
Auto airflow rate
High fan speed mode
Auto-cooling/heating change-over
Low gas pressure detection *2
Emergency operation
Self-diagnosis function
Mould-proof air filter
Silver ion anti-bacterial drain pan
Hot start
Year-round cooling applicable
Night quiet operation *2
RZQS50-140AV1
RZQS100-140AY1
RZQ71-140LV1
3step 3step 3step
*3
*5 *5
*5
*5 *5
*4

Insufficient gas charging is normally hard to detect. During test
run after installation and regular inspection, the refrigerant level
is monitored by a microprocessor to maintain proper gas
pressure. Reliability is assured and maintenance and inspection
can be carried out more quickly.
Low gas pressure detection
Even if there is a malfunction elsewhere in the system, the fan or
compressor can still be operated. (depending on the malfunction)
Emergency operation
The operating parameters of indoor and outdoor units, and
sensor data at critical locations throughout the system, are
constantly monitored using a microcomputer. To facilitate a quick
response in the event of a malfunction, a message appears on
the LCD of the remote controller and an LED on the unit
illuminates.
Self diagnosis function
Work and Servicing
If the refrigerant piping length does not exceed 30 m, there is no
need for on-site gas charging.
Pre charged for up to 30 m
The filter sign warns you when it is time to clean the filter.
*When using a wired remote controller the sign is displayed in the LCD. When
using a wireless remote controller the filter sign lamp illuminates on the signal
receiver unit.
Filter sign
Steeper gradient realises more
efficient condensate drainage.
High-lift is especially useful for long
lengths of drain piping.
Drain pump mechanism
Applicable for ceiling mounted cassette type and ceiling suspended type.
Daikin's innovative air discharge mechanism keeps airflow away
from the ceiling. Ceiling cleaning is less frequently required.
Ceiling soiling prevention
Applicable for ceiling mounted cassette type.
Two types are available: 65% and 90% colorimetry.
You can provide air-conditioning with fresh air from outside.
Convenient for places where a ventilation fan cannot be installed.
Fresh-air intake kit
Options
Applicable for ceiling mounted cassette type. Applicable for ceiling mounted cassette type.
To achieve increased durability by improved resistance to salt corrosion and atmospheric pollution, Anti corrosion treated fin for heat
exchangers (with special coating) are used for the heat exchanger of the outdoor unit.
In high corrosive areas, regular maintenance needs to be carried out.
Anti corrosion treated heat exchangers
Others
You can turn up to 16 indoor units on/off with a single remote
controller. (When using connected indoor units, the settings
must all be the same and on/off will be simultaneous.)
Group control by 1 remote controller
An optional central remote controller enables centralised control
of up to 1024 indoor units (64 groups) from up to 1 km away.
Central remote control
Enables interlocking control with external equipment such as
Heat Reclaim Ventilator.
Interlock control with Heat Reclaim Ventilator
Control features
If there is a power outage while the equipment is operating,
operations will restart in the same mode as before the power cut
when electricity is restored.
Auto-restart
Using 2 remote controllers you can operate the equipment locally
or from a remote location.
Note: When a wireless remote controller is used, remote control by two remote controllers is
not possible.
Control by 2 remote controllers
Detects difference in preset temperature and actual room
temperature and automatically switches to cooling or heating
accordingly.
Auto cooling / heating change-over
Operation and monitoring is carried out using the contact signal
from the operation control box in the building monitoring room.
External command control
*An option is required.
Standardly equipped interface enables connection to centralised
control system without need of an adaptor.
FUNCTIONS
21 22
Abundance of features that provide comfortable
air-conditioning in stores and offices.
Note: Some features only available on selected models. See overview pages for full list of features applicable to each unit.
The air flow direction can be
fixed at your desired angle by
the remote controller.
Delivers comfortable
air-conditioning to all areas, near
to and far from the air-conditioner.
Auto-swing
Applicable for ceiling mounted cassette type and ceiling suspended type.
Note:When units are installed on high ceilings, depending on the model, various
restrictions concerning maximum height, air discharge direction, and choice
of options may apply.
Delivers
air-conditioning
comfort all the way
down to the floor in
air-conditioning zones
with high ceilings.
High-ceiling application
High setting provides maximum reach while low setting
minimises drafts.
Switchable fan speed
Dehumidification is a microprocessor controlled to prevent abrupt
and uncomfortable changes in air temperature. Useful for
reducing uncomfortable humidity without uncomfortable cooling
of the room.
Programme "Dry"
Applicable for wall mounted type.
You can increase fan speed approximately 10% higher than the
"high" setting.
High fan speed mode
Efficient cooling even in winter when the indoor temperatures are
higher than those outside, such as in underground public spaces
or offices with many computers.
Year-round cooling applicable
The Automatic night quiet mode will initiate 8 hours after the
peak temperature is reached in the daytime, and normal
operation will resume 10 hours after that.
Night quiet operation
Cold air flow is avoided when heating operation starts or when
switching to heat after defrosting.
Hot start
Use the temperature-sensor in the
indoor unit when controlling air
conditioning from another room.
Temperature-sensors are included in the indoor unit and optional
wired remote controller. Temperature sensing closer to the
target area is possible to further
increase the comfort level.
Note: Wireless remote controllers have no
temperature-sensor.
Two selectable temperature-sensors
Comfort
Draft prevention function (heating)
To prevent cold air drafts, automatically adjusts airflow to near
horizontal position when heating initially starts or when the
thermo off.
DC fan motor improves efficiency.
DC fan motor (indoor unit)
(1) standard setting (2) Draft prevention setting
(standard, ceiling soiling prevention)
You can freely set air discharge settings by remote controller.
Swing pattern selection
Airflow rate is automatically controlled in accordance with the
difference between room temperature and set temperature.
Auto airflow rate
The air filter has an anti-bacterial treatment to help prevent the
growth of bacteria and mould on it.
Anti-bacterial air filter
Cleanliness
A built-in antibacterial treatment that uses silver ion in the drain
pan prevents the growth of slime, bacteria, and mould that cause
smells and clogging.
Silver ion anti-bacterial drain pan
Sanitary filter has mould-resistant treatment.
Mould-proof air filter
Remote Controller
Sets and saves setting for an increment of time that
automatically turns off air conditioner after a preset period of time
for each time operation starts.
Up to five operation ON/OFF settings can be programmed per
day for each day of the week. Not only can the time be set for the
operation ON setting, but also the temperature.
Weekly schedule timer
Even if the set temperature is changed, it returns to the preset
temperature after a preset period of time.
Setpoint auto reset
Saves energy by limiting the minimum and maximum set
temperatures. Avoids excessive heating and cooling.
Setpoint range set

23 24
dB(A)
Sound power level
dB(A)
Night quiet mode
°CWB
°CWB
Cooling capacity1,3
Rated (Min. - Max.)
kW
kW/kW
kW
EER
COP
°CDB
Cooling
Heating
Certified
Operation range
Sound pressure
level4
Cooling
Heating
Certified
Operation range °CDB
Motor output
Compressor
Model
Name
Indoor unit
Outdoor unit
Dimensions (HXWXD)
Colour
mm
dB(A)
kW
Refrigerant charge (R-410A) kg
dB(A)
Dimensions (HXWXD) mm
Machine weight kg
Piping
connections
mm
Liquid (Flare)
mm
Gas (Flare)
mm
Drain Indoor unit
Outdoor unit
Machine weight kg
Airflow rate (H/M/L)
Outdoor
unit
Colour
mm
Heating capacity2,3
Rated (Min. - Max.)
kW
Heat insulation Both liquid and gas piping
Max. interunit piping length
m
m
Max. installation level difference
Power supply
Type
Heating
Cooling
Cooling/Heating
Cooling/Heating
Sound pressure level (H/M/L)4
Indoor
unit
49 50
dB(A)
Sound power level (H/M/L)
Ivory white
White
m3
/min
/s
71 100 125
FHQ71DAVMA FHQ100DAVMA FHQ125DAVMA
RZQS71AV1 RZQS100AV1 RZQS125AV1
140
FHQ140DAVMA
RZQS140AV1
140
FHQ140DAVMA
RZQS140AY1
38/36/34 42/38/34 44/41/37 46/42/38 46/42/38
235X1,270X690 235X1,590X690
o
/ 9.5
o
/ 15.9
990X940X320
75
1,430X940X320
108
38
Hermetically sealed scroll type
1 Phase, 220-240 V, 50 Hz 3 Phase, 380-415 V, 50 Hz
14 to 25
15 to 27
55/53/51
32
3.23 3.15
3.22 3.10
3.04
3.24
3.23
-5 to 46
-15 to 15.5
30
50/52
46
53/55 54/56
75
(equivalent length 90)
o
/ 26.0 (Hole)
1.55
2.9
(Charged for 30 m) (Charged for 30 m)
VP20 (I.Do
/ 20XO.Do
/ 26)
20.5/17/14 28/24/20 31/27/23 34/29/24 34/29/24
342/283/233 467/400/333 517/450/383 567/483/400 567/483/400
10.0
(5.0-11.2)
12.5
(5.7-14.0)
11.2
(5.1-12.8)
14.0
(6.0-16.2)
13.2
(6.2-15.5)
16.0
(6.2-18.0)
16.0
(6.2-18.0)
3.15
4.0
(Charged for 30 m)
4.2
(Charged for 30 m)
4.0
(Charged for 30 m)
4.2
60/56/52 62/59/55 64/60/56 64/60/56
42/38/34 44/41/37
60/56/52 62/59/55
3.23
3.22
3.15
3.10
3.04
3.24
28/24/20 31/27/23
467/400/333 517/450/383
10.0
(5.0-11.2)
12.5
(5.7-14.0)
13.2
(6.2-15.5)
11.2
(5.1-12.8)
14.0
(6.0-16.2)
3.28
kW
kW
Power consumption
Heating2
Cooling1 3.10 3.97
3.48 4.52
4.34
4.94
2.48
3.10
3.48
3.97
4.52
4.34
4.94
2.16
7.1
(3.2-8.0)
8.0
(3.5-9.0)
60
FHQ60DAVMA
RZQS60AV1
3.33
1.6
3.38
2.04
1.78
6.0
(3.2-6.0)
6.8
(3.5-8.0)
Hermetically sealed swing type
50
FHQ50DAVMA
RZQS50AV1
37/35/32
235X960X690
770X900X320
64
54/52/49
25
3.43
48/50
44
50
(equivalent length 70)
1.3
2.0
(Charged for 30 m)
15/12/10
250/200/167
3.48
1.75
1.44
5.0
(3.2-5.6)
6.0
(3.5-7.0)
100 125
FHQ100DAVMA FHQ125DAVMA
53/55 54/56
49 50
69
66 ---------- 69 ----------
°CWB
°CWB
Cooling capacity1,3
Rated (Min. - Max.)
kW
kW
kW
Power consumption
°CDB
Cooling
Heating
Certified
Operation range
Night quiet mode
Sound pressure
level4
Sound power level
Cooling
Heating
Certified
Motor output
Compressor
Model
Name
Indoor unit
Outdoor unit
Dimensions (HXWXD)
Colour
mm
dB(A)
kW
Refrigerant charge (R-410A) kg
dB(A)
dB(A)
Machine weight kg
Piping
connections
mm
Liquid (Flare)
mm
Gas (Flare)
mm
Drain Indoor unit
Outdoor unit
Machine weight kg
Outdoor
unit
Colour
mm
Heating capacity2,3
Rated (Min. - Max.)
kW
Heat insulation
Max. interunit piping length m
m
Power supply
Type
Heating2
Cooling1
Cooling/Heating
Indoor
unit
dB(A)
Sound power level (H/M/L)
Cooling/Heating dB(A)
WALL MOUNTED TYPE
71 100 100
FAQ71CVEA
RZQS71AV1
FAQ100CVEA
RZQS100AV1
FAQ100CVEA
RZQS100AY1
45/42/40
13
290X1,050X238
61/58/56
17
340X1,200X240
65/62/58
o
/ 9.5
50/52
46
990X940X320
75 108
Ivory white
30
Both liquid and gas piping
Fresh white
o
/ 15.9
Hermetically sealed swing type Hermetically sealed scroll type
o
/ 26.0 (Hole)
1.55 3.15
2.9 (Charged for 30 m)
VP13 (I.Do
/ 13XO.Do
/ 18)
300/267/233
m3
/min 18/16/14
49/45/41
433/383/317
26/23/19
53/55
49
1,430X940X320
4.0 (Charged for 30 m)
69
-5 to 46
-15 to 15.5
50 (Equivalent length 70 m) 75 (Equivalent length 90 m)
14 to 25
15 to 27
/s
2.23
2.33
3.19
3.44
kW/kW
kW
EER
COP Heating
Cooling 3.18
3.43
3.13
3.26
7.1
(3.2-8.0)
8.0
(3.5-9.0)
10.0
(5.0-11.2)
11.2
(5.1-12.8)
Note :
1
Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2
Rated heating capacities are based on the following conditions: Indoor temp., 20°CDB, 15°CWB; outdoor temp., 7°CDB, 6°CWB. Equiv. refrigeration piping, 7.5 m (horizontal)
3
Capacities are net, including a deduction for cooling for indoor fan motor heat.
4
The operation sound is measured in anechoic chamber. If it is measured under the actual installation conditions, it is normally over the set value due to environmental noise and sound reflection.
kW
kW
Power consumption
Heating2
Cooling1 1.84
1.79
1.67
1.74
1.27
1.41
2.57
2.77
3.56
3.60
4.40
4.38 2.77 3.60 4.38
2.57 3.56 4.40
kW/kW
kW
EER
COP Heating
Cooling 3.85
4.46
3.59
4.02
3.94
4.26
3.89
4.05
3.51
3.89
3.18
3.65 4.05 3.89 3.65
3.89 3.51 3.18
Note :
1
Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2
Rated heating capacities are based on the following conditions: Indoor temp., 20°CDB, 15°CWB; outdoor temp., 7°CDB, 6°CWB. Equiv. refrigeration piping, 7.5 m (horizontal)
3
Capacities are net, including a deduction for cooling for indoor fan motor heat.
4
The operation sound is measured in anechoic chamber. If it is measured under the actual installation conditions, it is normally over the set value due to environmental noise and sound reflection.
dB(A)
°CWB
Cooling capacity1,3
Rated (Min. - Max.)
kW
°CDB
Cooling
Heating
Certified
Operation range
Sound pressure
level4
°CWB
Cooling
Heating
Certified
Motor output
Compressor
Model
Name
Indoor unit
Outdoor unit
Dimensions
(HXWXD)
Colour
mm
mm
dB(A)
kW
Refrigerant charge (R-410A)
kg
dB(A)
Machine weight kg
Unit
Piping
connections
mm
Liquid (Flare)
mm
Gas (Flare)
mm
Drain Indoor unit
Outdoor unit
Decoration panel
Unit
Decoration panel
Machine
weight kg
kg
Unit
Decoration panel
m3
/min
Outdoor
unit
Colour
mm
dB(A)
Heating capacity2,3
Rated (Min. - Max.)
kW
Heat insulation
m
Power supply
Type
Cooling/Heating
Sound power level dB(A)
Sound power level (H/L)
Indoor
unit
71
FCQ71KAVEA
RZQS71AV1
60
FCQ60KAVEA
RZQS60AV1
50
FCQ50KAVEA
RZQS50AV1
256X840X840
50X950X950
21
5.5
o
/ 9.5
o
/ 15.9
50/52
48/50
44 46
990X940X320
770X900X320
75
64
o
/ 26.0 (Hole)
1.55
1.6
1.3
2.9
(Charged for 30 m)
2.0
(Charged for 30 m)
VP25 (I.Do
/ 25XO.Do
/ 32)
7.1
(3.2-8.0)
8.0
(3.5-9.0)
6.0
(3.2-6.0)
7.0
(3.5-8.0)
5.0
(3.2-5.6)
6.0
(3.5-7.0)
100
FCQ100KAVEA
RZQS100AV1
43/37.5/32
53/55
1,430X940X320
108
24
298X840X840
3.15
4.0
(Charged for 30 m)
32/26/20
10.0
(5.0-11.2)
11.2
(5.1-12.8)
125
FCQ125KAVEA
RZQS125AV1
44/39/34
54/56
4.2
(Charged for 30 m)
33/28/22.5
12.5
(5.7-14.0)
14.0
(6.0-16.2)
140
FCQ140KAVEA
RZQS140AV1
44/40/36
14.0
(6.2-15.5)
16.0
(6.2-18.0)
/s 533/433/333 550/467/375
21/17.5/13.5
350/292/225
35/31.5/28
49 50
Night quiet mode
----------
30
Ivory white
15 to 27
14 to 25
-5 to 46
-15 to 15.5
100
FCQ100KAVEA
RZQS100AY1
4.0
(Charged for 30 m)
32/26/20
10.0
(5.0-11.2)
11.2
(5.1-12.8)
125
FCQ125KAVEA
RZQS125AY1
4.2
(Charged for 30 m)
33/28/22.5
12.5
(5.7-14.0)
14.0
(6.0-16.2)
140
FCQ140KAVEA
RZQS140AY1
14.0
(6.2-15.5)
16.0
(6.2-18.0)
533/433/333 550/467/375
Fresh white
75 (Equivalent length 90)
50 (Equivalent length 70)
43/37.5/32 44/39/34 44/40/36
53/46 60/50 61/52 61/54 60/50 61/52 61/54
53/55 54/56
69
66 ---------- 69 ----------
49 50
71 100 125
Model
Name
Indoor unit
Outdoor unit
O
CWB
Cooling capacity
rated (Min. - Max.)1,3 kW
O
CDB
Cooling
Heating
Certified Outdoor
Operation Range
Sound pressure
level4
O
CWB
Cooling
Heating
Certified Indoor
Operation Range O
CDB
Motor output
Compressor
Dimensions
(HXWXD)
Colour
mm
mm
dB(A)
kW
Refrigerant charge (R-410A)
kg
dB(A)
Machine weight kg
Unit
Piping
connections
mm
Liquid (Flare)
mm
Gas (Flare)
mm
Drain Indoor unit
Outdoor unit
Decoration panel
Unit
Decoration panel
Machine
weight kg
kg
Unit
Decoration panel
m3
/min
Outdoor
unit
Colour
mm
dB(A)
Heating capacity
rated (Min. - Max.)2,3 kW
Heat insulation
m
Power supply
Type
Cooling/Heating
Sound power level dB(A)
Sound power level (H/L)
Indoor
unit
/s
50 (Equivalent length 70) 75 (Equivalent length 90)
----------
1 Phase, 220-240 V, 50 Hz
30
Ivory white
15 to 27
14 to 25
-5 to 46
-15 to 15.5
Fresh white
FCQ71KAVEA
RZQ71LV1
21
256X840X840
50X950X950
5.5
o
/ 9.5
o
/ 15.9
49/51
770X900X320
64
o
/ 26.0 (Hole)
1.7
2.0
(Charged for 30 m)
VP25 (I.Do
/ 25XO.Do
/ 32)
21/17.5/13.5
FCQ100KAVEA
RZQ100LV1
51/53
990X940X320
75
24
298X840X840
2.08
2.9
(Charged for 30 m)
32/26/20
10.0
(5.0–11.2)
11.2
(5.1–12.8)
FCQ125KAVEA
RZQ125LV1
1,170X900X320
98
2.4
3.15
(Charged for 30 m)
33/28/22.5
12.5
(5.7–14.0)
14.0
(6.0–16.2)
FCQ140KAVEA
Inverter series
RZQ140LV1
66 69 ----------
54/56
dB(A)
Night quiet mode 45 47 50
1,430X940X320
108
3.15
4.2
(Charged for 30 m)
350/292/225 533/433/333 550/467/375
13.6
(6.2–15.5)
16.0
(6.2–18.0)
kW
kW
kW/kW
kW
Power consumption
Heating2
Cooling1 2.64
2.84
7.1
(3.2–8.0)
8.0
(3.5–9.0)
1.99
2.10
4.02
3.83
4.53
4.80
35/31.5/28 43/37.5/32 44/39/34 44/40/36
53/46 60/50 61/52 61/54
EER
COP Heating
Cooling 3.79
3.95
3.57
3.81
3.11
3.66
3.00
3.33
140
SPECIFICATIONS

For each flow pattern – all round, 4-way, 3-way, 2-way, branch duct connection – the compatibility of each independently installed option
(shown in the column on the left) to accessory options (listed across the top of each table) is shown in the cells where the relevant row and column intersect.
A circle (o) indicates compatibility, and a cross (x) indicates incompatibility. Any options not shown below are not suitable for independent or accessory installation.
Round flow type: List of optional parts required to achieve different flow patterns
1
In some cases, depending on how the unit is embedded in the ceiling, use of branch ducts and fresh air intake kits may not be possible. Before starting installation work make sure to check
whether or not joint installation is possible. In particular, ensure that the lower fixing position caused by the addition of panel spacers is acceptable.
2
Use a chamber connection kit if two different types of optional chamber are used together. In this case, the fresh air intake kit must be installed in the upper position.
3
It is not possible to use panel spacers in a 2-way flow installation.
4
It is not possible to install a branch duct on the same side to which a fresh air intake kit (direct mount) is installed.
Panel/grille related
Independently installable optional parts
Operation control related
Auxillary function related
Filter related
Optional accessory parts
Panel spacer1
Panel spacer1
o o o
x
Wireless remote controller o o o
o
Fresh air intake kit (direct mount) o o o
o
x o o
x
High-efficiency filter2
o o o
x
High-humidity operation kit
Panel/grille related
Operation control related
Auxillary function related
Panel spacer1
Wireless remote controller
Fresh air intake kit (direct mount)
High-humidity operation kit
All-round flow 4-way flow
o3 o3 x
x
o3 o
x
x
x
o
o3 o x
x
o
x o o
3-way flow 2-way flow
1-way branch / unit 3-way flow
Branch duct1
(Chamber type)
(Round duct type)
o o o4 x
x
x o o4 x
x
x o o4 x
x
Branch duct connection
Wireless
remote controller
(direct mount)
High-efficiency
filter2
High-humidity
operation kit
Panel spacer1 Wireless
remote controller
(direct mount)
High-efficiency
filter2
High-humidity
operation kit
Panel spacer1 Wireless
remote controller
(direct mount)
Fresh air intake kit (Chamber type)1,2
o o o
x
Fresh air intake kit (Chamber type)1,2
o3 o x
x
o
o
x
o
o3
o
x
x
x
o
o
o
(Chamber type)1,2
(Chamber type)1,2
(Chamber type)1,2
High-efficiency
filter2
High-humidity
operation kit
Indoor unit
intelligent Touch Controller4
Note: 1
Refer to page 10 for the details.
2
Required for installing high-efficiency filter unit.
3
Wiring for wired remote controller to be procured locally.
4
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
5
Installation box for adaptor PCB (KRP1H98) is necessary.
Kit name
KDJP55B160
KDJP55B80
KAFP556B80
KAFP557B80
KAFP552B80
KAFP553B80
KAFP556B160
KAFP557B160
KAFP552B160
KAFP553B160
FCQ71KAVEA FCQ100KAVEA
FCQ50KAVEA FCQ60KAVEA FCQ125KAVEA FCQ140KAVEA
Name of option Remark
Chamber
type
Decoration panel
Fresh air
intake kit1
Central remote controller4
Unified ON/OFF controller4
Schedule timer4
Adaptor for wiring5
Without T-duct joint
With T-duct joint
Direct installation type
Sealing material of air discharge outlet
Panel spacer
Wiring adaptor for electrical appendices(2)5
Installation box for adaptor PCB
High-efficiency filter unit
(including filter chamber)
(Colorimetric method 65%)
Replacement
high-efficiency filter
Remote controller Wireless type Heat pump
Wired type3 "Nav Ease"
Branch duct chamber
Remote sensor (for indoor temperature)
DCS601C51
DCS302CA61
DCS301BA61
DST301BA61
KRP1C63
KDBH55K160F
KDBP55H160FA
KDDP55B160
KDDP55B160K
KDDP55X160
KRP4AA53
BRC7F634F
BYCP125K-W1
KRP1H98
KRCS01-4B
BRC1E62
KDDFP55B160
Filter chamber
Navigation Remote Controller
Outdoor unit
Kit name
KKPJ5F180
K-KYZP15C
KPT-60B160
KKPJ5G280
KKTP5B112
KRP58M51
Heat pump
Central drain plug
Wire fixture for preventing overturning
Name of option
Fixture for preventing overturning
Demand adaptor
RZQS71AV1
RZQS60AV1
RZQS50AV1
RZQS100AV1 RZQS125AV1 RZQS140AV1
RZQS100AY1 RZQS125AY1 RZQS140AY1
25 26
Indoor unit
Note: 1
2
3
Installation box for adaptor PCB (KRP4AA93) is necessary.
WALL MOUNTED TYPE
intelligent Touch Controller2
Remote controller
Schedule timer2
Wiring adaptor for electrical appendices3
Electrical box with earth terminal (3 blocks)
Kit name
FAQ100CVEA
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
intelligent Touch Controller2 DCS601C51
KRP4AA51
KJB311AA
KJB212AA
Drain-up kit
Noise filter ( For electromagnetic interface use only)
Remote sensor (for Indoor temperature) KRCS01-4B
FAQ71CVEA
K-KDU572EVE
KRP4AA93
KEK26-1A
BRC7EB518
Wireless type Heat pump
Wired type1 "Nav Ease" BRC1E62
Kit name
Note:
L-type piping kit (for upward direction)
Drain pump kit
Remote controller Wireless type
Schedule timer2
Wiring adaptor for electrical appendices3
1
2
3
Installation box for adaptor PCB is necessary.
FHQ71DAVMA
FHQ60DAVMA
FHQ50DAVMA FHQ100DAVMA FHQ125DAVMA FHQ140DAVMA
Remote sensor (for indoor temperature)
Wired type1 "Nav Ease"
BRC7GA53
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
Wiring adaptor for electrical appendices KRP1BA54
KRP4AA52
KRP1D93A
Adaptor box mounting plate -
KKSAP50A56
KDDQ50A140
KDU50P140VE
KRCS01-4B
KHFP5N160
KJB311AA
KJB212AA
Heat pump
Kit name
KKPJ5F180
K-KYZP15C
KPT-60B160
KRP58M51
KKPJ5G280
KKTP5B112
KKPJ5F180
KPT-60B160
KKPJ5G280
KKTP5B112
Central drain plug
Wire fixture for preventing overturning
Name of option
Fixture for preventing overturning
Demand adaptor
OPTIONS
KDTP55K160
Chamber connection kit2
Insulation kit for high humidity
KKSJ55KA160
KDTP55K80

Notes:
1
Sticking location for manufacture's label
manufacture's label for indoor unit:
Suction grille inner side's electric components box's lid surface
manufacture's label for decoration panel :
Decoration panel's corner decoration cover inner surface
2
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller
in detail.
3
When the temperature and humidity in the ceiling exceed 30˚C and RH 80% or the fresh air is inducted into the ceiling or the unit
continues 24 hour operation, an additional insulation (thickness 10mm or more of glasswool or polyethylene form) is required.
4
Though the installation is acceptable up to maximum of 910mm square ceiling opening, keep the clearance of 35mm or less
between the indoor unit and the ceiling opening so that
the panel overlap allowance can be ensured.
5
Please do not place the thing been damp and troubled under an indoor unit.
When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
950
950
arrow view
A
Piping Connection
Side
Drain Connection
Side
Note 2
8
6
7
860~910(Ceiling opening space) (Note 4)
710(Hanging bolt pitch)
420
420
780(Hanging
bolt
pitch)
860~910(Ceiling
opening
space)
(Note
4)
300
or less
9
B
C
(round shape type)
840
340
80 80
124
55 55
256
124
110
95
40
29
850
175
Adjustable(0~675)
10
246
160
50
165
125
Connection position
of branch duct
(square-shaped type)
4 1 2
2 100=200
16-M4 Prepared hole
Connection position
of branch duct
Hanging bolt
4-M8~M10
C/L
20
157
350
280
330 1500
or
more
(required
space)
From
the
floor
side
2500
or
more
Connection position
of branch duct
Connection position
of branch duct
(round shape type)
27-M4 Prepared hole
35 or less
(Note 4)
35 or less
(Note 4)
A
For
height
installation
81
124
2x100=200
157
124
105
64
55
840
110
350
160
130
95
50
256
5
85
55
60
42
150
3
Connection position
of branch duct
(round shape type)
Connection position
of branch duct
16-M4 Hole
arrow view
B
95
85
350
C/L
124
81
110
160
2x100=200
124
157
[FCQ50-71KAVEA]
20-M4
Prepared hole
Connection position
of branch duct
Connection position
of branch duct
(round shape type)
Connection position
of fresh air intake kit
(direct installation type)
ø100
(knock
hole)
arrow view
C
2x100=200
160
C/L
350
124
95
109
80
90
183
25
90
157
80
213
124
[FCQ50-71KAVEA]
C/L
160
167
67
95
29
93
90
196
80
80
160
25
90
213
157
350
20-M4
Prepared hole
Connection position
of branch duct
Connection position
of branch duct
(round shape type)
Connection position
of fresh air intake kit
(direct installation type)
ø100
(knock
hole)
arrow view
C
2
100=200
[FCQ100-140KAVEA]
1500
or
more
(required
space)
From
the
floor
side
2500
or
more
For
height
installation
50
64 160
256
157
350
130
95
60
105
150
42
93
67
29
160
167
840 55
55
81 85
Connection position
of branch duct
Connection position
of branch duct
(round shape type)
27-M4 Prepared hole
35 or less
35 or less
(Note 4)
(Note 4)
3
5
A
2 100=200
[FCQ50-71KAVEA] [FCQ50-71KAVEA]
[FCQ100-140KAVEA]
[FCQ50-140KAVEA] [FCQ50-140KAVEA]
[FCQ100-140KAVEA]
2 100=200
160
C/L
160
157
350
81 85
67
167
95
29
93
Connection position
of branch duct
(round shape type)
Connection position
of branch duct
16-M4 Hole
arrow view
B
[FCQ100-140KAVEA]
Adjustable(0~675)
Connection position
of branch duct
16-M4 Prepared hole
(round shape type)
Connection position
of branch duct
Hanging bolt
4-M8~M10 1
160
850
280
80
10
330
340
50
55
4
55
40
80
125
29
95
157
298
167
160
350
175
165
288
20
2 100=200
2
840
160
C/L
The necessary space is 500mm or more when the
air-outlet is blocked with the accessory.
Moreover when the corner areas are blocked
(both right and left of the blocked air outlet),
the necessary space is 200mm or more.
1500mm or more
200mm or more
1500mm or more
1500mm
or more
1500mm
or more
200mm
or more
Required space
27 28
57
131
φ45
197
91
6
4 5 1
1
14
197
5
57
690
(Required
space)
For
height
installation
From
the
floor
side
2500
or
more Floor side
(Required
space)
Obstacle
300
or
more
13
1270
235
30 or more
(Service space)
30 or more
(Service space)
4-M8~M10
Hanging bolt
1
268
156
83
214
221
76
268
105
(Note.2)
Brand name plate
The Front
(For left pipe)
Drain piping connection VP20
6
4
5
7
2
3
57
1230
87
195
35
102
(Hanging
bolt
pitch)
210
116
(Hanging bolt pitch)
210
131
105
30
100
156
260
189
163
8
18
10
17 16
20
5
220
103
175
Position : Hole of wall for taking out in pipe back
(View from the front)
(Required
space)
19 15
120
90
51
92
63
60
63
40
134 59
157
115
90
175
Position slit hole for taking out in pipe back
Connection position of fresh air intake kit
φ100(Knock out hole)
12
9
91
57
197
131
φ45
6
4 5 1
1
14
690
Floor side
(Required
space)
57
197
(Required
space)
5
Obstacle
300
or
more
For
height
installation
From
the
floor
side
2500
or
more
13
235
30 or more
(Service space)
30 or more
(Service space)
960
1
4-M8~M10
Hanging bolt
214
76
105
268
268
156
221
83
6
4
5
7
2
3
(For left pipe)
(Note.2)
Brand name plate
The Front
57
87
116
189
210
102
30
210
163
105
100
156
920
(Hanging
bolt
pitch)
260
195
131
35
8
18
10
17 16
20
220
5
103
175
19 15
(Required
space)
90
157
115
63
40
59
92
134
60
175
90
63
120
51
12
9
Notes:
1
2
3
Location of unit's Name Plate: Bottom of fan housing inside the suction grille.
In case of using wireless remote controller, this position will be a signal receiver.
Refer to the drawing of wireless remote controller in detail.
When the case where humidity is 80% or more, and the drain outlet are choked up
and the air filter are dirty, dew may fall.
[FHQ50-60DAVMA]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Air discharge grille
Air suction grille
Air filter
Gas pipe connection
Liquid pipe connection
Drain pipe connection
Earth terminal (inside the control box) (M4)
Hanger
Rear pipe penetration cover
Top panel penetration cover
Right side pipe connection
Left back drain pipe connection
Left side drain pipe connection
Right side drain pipe connection
Hole of wall for taking out in pipe back
Upward drain pipe connection
Upward gas pipe connection
Upward liquid pipe connection
Power supply wiring and a unit wiring back connection
Power supply wiring and a unit wiring upper connection
Notes:
1
2
3
[FHQ71DAVMA]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Air suction grille
Air filter
Gas pipe connection
Hanger
Gas pipe connection
Transmission wiring connection
Remote controller wiring
connection
Air-outlet
Suction grille
Corner decoration cover
Drain hose (accessory)
1
2
3
4
5
6
7
8
9
DIMENSIONS (Unit: mm)

30
29
6
φ80 hole
5
φ80 hole
894
Approx.475
52
105
104
98
Piping and
Wiring intake
Outside line
14.5
44
Mounting location
4
60
44
Approx.390
Approx.345
8
120 or less
For installation
in high spaces
50
or
more
2500 or more
30
or
more
(Required
space)
(Required
space)
Piping direction
2 1
9
238
Approx.400
290
240
Dimensions
for full open
front panel
3
50 or more
Name plate Note)2
50 or more
Piping direction
Piping direction
1050
7
(Requred space) (Requred space)
WALL MOUNTED TYPE
[FAQ71CVEA]
Front panel
Front grill
Air outlet
Gas piping
Liquid piping
Drain hose
Earth terminal
Right side pipe connection hole
Left side pipe connection hole
1
2
3
4
5
6
7
8
9
Notes:
1
2
3
Location of unit's of Name Plate:Right side surface of casing
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail.
Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more,
and the drain outlet are choked up and the air filter are dirty, dew may fall.
Approx.400
5
65
45
4
45
Piping and
Wiring intake
79.5
Approx.465
6
Mounting location
φ80 hole
114
1085
14.5
φ80 hole
Outside line
Approx.460
89
35.5
Piping direction
(Required
space)
(Required
space)
120 or less
8
2500 or more
For installation
in high spaces
50
or
more
30
or
more
(Requred space) (Requred space)
1200
7
50 or more 50 or more
Piping direction
Name plate Note)2
Piping direction
3
9
Approx.440
Dimensions for
full open
front panel
242
340
2 1
240
WALL MOUNTED TYPE
[FAQ100CVEA]
Front panel
Front grill
Air outlet
Gas piping
Liquid piping
Drain hose
Earth terminal
Right side pipe connection hole
Left side pipe connection hole
1
2
3
4
5
6
7
8
9
Notes:
1
2
3
Location of unit's of Name Plate:Right side surface of casing
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail.
Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more,
and the drain outlet are choked up and the air filter are dirty, dew may fall.
131
57
197
φ45
91
6
4 5 1
1
14
57
5
197
690
Floor side
(Required
space)
Obstacle
300
or
more
For
height
installation
From
the
floor
side
2500
or
more
(Required
space)
13
235
1590
30 or more
(Service
space)
30 or more
(Service
space)
4-M8~M10
Hanging bolt
1
156
83
268
221
105
76
268
214
The Front
(Note.2)
Brand name plate
(For left pipe)
6
4
5
7
2
3
189
57
102
35
210
156
131
30
87
260
210
105
195
163
116
100
1550
(Hanging
bolt
pitch)
8
18
10
17 16
20
103
220
5
175
(Required
space)
19 15
157
90
60
175
59
92
120
90
63
134
51
40
115
63
12
9
Notes:
1
2
3
[FHQ100-140DAVMA]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Air suction grille
Air filter
Gas pipe connection
Hanger

32
OUTDOOR UNIT // RZQ125LV1
OUTDOOR UNIT // RZQS100/125/140AV1, RZQS100/125/140AY1, RZQ140LV1
31
30
89
54
4
5
423
3
1170
95
900
422
142
7
6
2
19
1
60
89
7
80
84
145
19
5
95
6
54
55
13 67
5
223
52
7
6
53
95
55
102
45 376 191
117
70
16
8 16
5
58
71
620
30
350
140
140
(345~355)
94
30
61
320
43
41
Hole for anchor
bolt 4-M12
Gas pipe connection
Service port
Earth terminal
Refrigerant piping intake
Power supply wiring intake
Wiring between unit intake
Drain outlet
Drain port
1
2
3
4
5
6
7
8
9
Gas pipe connection
Service port
Grounding terminal
Control wiring intake
Drain outlet
1
2
3
4
5
6
7
8
30
161
19
25
8
20
154
16
9
99
58
71
201
36
6
295
5
16
179
54
145
6
80
95
84
5
19
7
55
95
53
13
5
67
1430
4
6
423
89
1
60
19
54
89
142
95
940
422
3
5
7
2
37
160
91
55
38
620
30
30
320
Hole for anchor bolt 4-M12
160
350
(345
∼
355)
OUTDOOR UNIT // RZQS71AV1, RZQ100LV1
OUTDOOR UNIT // RZQS50/60AV1, RZQ71LV1
Gas pipe connection
Service port
Earth terminal M5 (in switch box)
Transmission wiring intake
1
2
3
4
5
6
7
8
Gas pipe connection
Service port
Grounding terminal (in switch box)(M5 )
Control wiring intake
1
2
3
4
5
6
7
8
30
54
95
55
8419 80
145
53
95
55
223
52
13 67
7
6
5
770
28
89
60
54
95
339
341
142
89 19
900
3
4
2
1
7
6
5
117
58
16
102
70
45
16
71
376 191
5
8
350
43
30
320
30
61
(345~355)
140 620
94
41
140
Hole for anchor
bolt 4-M12
91
55
38
345
37
(340∼350)
30
620
30
320
160
160
Hole for anchor
bolt 4-M12
7
5
6
95
52
67
53
223
55
13
30
5
6
7
53
55
145
95
19 80
84
142
340
6
5
4
7
339
3
95
990
19
1
89
53
940
60
89
2
203
8
16
5
36
25
153
58
179
19
35
99
71
6
16

33 34
H
L
500
or more
100
or more
L H
100 or more
100 or more
100 or more
100 or more
500 or more
When there are obstructions
on the inlet side and
both lateral sides
2. For series installation
(more than two units)
When there are
obstructions on
both sides
1. For single unit installation
When there is an
obstruction only
on the inlet side
2) When there is an obstruction
in the overhead space
on both sides
2) When there is an obstruction
When there is an
obstruction on the
inlet side
on the inlet side and
both lateral sides
2. For series installation (more than two units)
100 or more
500 or less
1000
or
more
An obstruction
in the overhead
space
500 or less
500 or more
1000
or
more
An obstruction
150 or more
150 or more
150 or more
500 or less
1000
or
more
An obstruction
in the overhead
space
For RZQS50-140AV1, RZQS100-140AY1, RZQ71-140LV1,
1000 or more
100 or more
100 or more
An obstruction
1000 or more
500 or less
1000
or
more
100 or more
100 or more
300
or more
1000 or more
200 or more
500 or less
1000
or
more
An obstruction
in the overhead
space
100 or more
100 or more
300 or more
1000 or more
200 or more
100 or more
100 or more
1000
or more
300
or more
L
L H
100 or more
100 or more
H
1) When the overhead space is open
When there is an obstruction on the inlet side
1
When there is an obstruction on the outlet side
2
(There is no limit to the height of the obstruction on the
outlet side.)
When there are obstructions on both
the inlet and outlet sides
(When the obstruction on the outlet side is higher than the
unit itself)
3
Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book.
REMOTE CONTROLLER
Receiver
Wireless type
Transmitting part
157
62 17.5
Liquid crystal
remote controller
(wireless)
Remote
controller
holder
Remote controller dimensions • Remote controller holder
installation procedure
< installation to wall
surface >
CEILING MOUNTED CASSETTE TYPE < Round Flow >
Receiver
Drain piping
side
Refrigerant
piping side
Decoration panel
Receiver installation procedure
Receiver detail
19
Upper case Lower case
40
23
46
28
48.5
42
84
5X7 oblong hole
Code outlet hole
5X15 oblong hole
Lower case portion
Lower case portion
Staple
19
A Exposed cord C Embedded cord
(use switch box)
B Embedded cord
84
46
Switch box for two switch
ex.) KJB211A
(optional accessory)
Condit
19
0~5
Switch box
[field supplied part]
(Between remote
controller and
control box)
48.5
19
Note)2
Through hole
40
( 8- 10)
84
28
Switch box for one switch
ex.) KJB111A
(optional accessory)
• Installation method
2.If the hole size is too large or the location
is not proper, the hole may come out from
the remote controller.
Note)
1. Remote controller cord and staple are not attached. They are field
supplied parts.
Size
Specifications of cord
0.75~1.25 mm2
Total length 500 m
Type Vinyl cord with sheath or cable (insulated thickness: 1mm or more)
BRC1E62
• Receiver detail
The Front
(Green)
120
120

Operation
lamp
Top left
outlet
Left outlet
Top center
outlet
• Receiver detail
Receiver
WALL MOUNTED TYPE
• Receiver installation procedure
• Receiver installation procedure
Wired type Remote controller dimensions
DIMENSIONS (Unit: mm) Installation service space for outdoor unit (Unit: mm)

Máy lạnh Daikin âm trần

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Máy lạnh Daikin âm trần

Similar to Máy lạnh Daikin âm trần (20)

Recently uploaded

Recently uploaded (20)

Máy lạnh Daikin âm trần