This document contains calculations of heat gains for a building project using the CLOAD software. It provides heat gain calculations for the whole building, for the first floor as a whole, and for an individual room on the first floor called Room 1, including sensible heat gains, latent heat gains, solar heat gains, transmission heat gains, infiltration heat gains, ventilation heat gains, occupant sensible and latent heat gains, lighting heat gains, and equipment sensible and latent heat gains.
KLIMA Software - Some DEMO Results Outputs in ENGLISH LanguageKLIMA Software
This document contains technical specifications and calculations for heat transfer coefficients, water vapor diffusion, thermal stability, heat gains, and fan coil unit selection for the DEMO PROJECT and DEMO BUILDING. It includes tables with values for U-coefficients, layer properties, temperature and humidity conditions, heat loads by source, and selected fan coil unit models and sizes.
This document summarizes the results of a steel code check for two structural members, 207 and 208. For each member, it provides properties, design criteria, service conditions, design checks for flexure, shear, tension, compression, torsion, and interaction. All design checks showed the members to be OK and within allowable ratios according to the specified design code ANSI/AISC 360-05 LRFD. Sections and material properties are also provided for each member.
The document summarizes the design results of a pitched truss with 15 meters length and 3 meters height composed of 28 vertical and diagonal web members and bottom and top chord members. The maximum axial force is 1.64 tons in the top chord member and the maximum shear is 0.06 tons and moment is 0.03 ton-meters in the top chord member. The bottom chord member meets the design criteria with a ratio of 0.05 under the critical load case of 1.4 times dead load.
Do you want to get up to speed with the most current release of Oracle Database? If so, this session is for you. You will learn about the most exciting and useful new features of Oracle Database 12c that can make your work as a database developer a lot easier. There is more to Oracle Database 12c than just pluggable databases.
The document contains SQL commands that create tables, insert data, and perform queries on the tables. The tables created are studies, software, and programmer. Data is inserted and various queries are run to retrieve, aggregate, and analyze the data. Key information summarized includes:
- Tables were created to store student studies data, software project data, and programmer details.
- Data was inserted into the tables and various queries were run to retrieve, calculate statistics on, and analyze the data across the tables.
- Queries included finding averages, minimums, maximums, counts, sums, and using functions like trunc, round, and to_char to manipulate dates and strings.
This document contains configuration information for the Windows boot process. It describes the Windows Boot Manager as the main boot loader, along with the Windows Boot Loader, Resume from Hibernate application, and Windows Memory Tester. It also includes global settings that are inherited by components like debug settings.
Dbms plan - A swiss army knife for performance engineersRiyaj Shamsudeen
This document discusses dbms_xplan, a tool for performance engineers to analyze execution plans. It provides options for displaying plans from the plan table, shared SQL area in memory, and AWR history. Dbms_xplan provides more detailed information than traditional tools like tkprof, including predicates, notes, bind values, and plan history. It requires privileges to access dictionary views for displaying plans from memory and AWR. The document also demonstrates usage examples and output formats for dbms_xplan.analyze.
KLIMA Software - Some DEMO Results Outputs in ENGLISH LanguageKLIMA Software
This document contains technical specifications and calculations for heat transfer coefficients, water vapor diffusion, thermal stability, heat gains, and fan coil unit selection for the DEMO PROJECT and DEMO BUILDING. It includes tables with values for U-coefficients, layer properties, temperature and humidity conditions, heat loads by source, and selected fan coil unit models and sizes.
This document summarizes the results of a steel code check for two structural members, 207 and 208. For each member, it provides properties, design criteria, service conditions, design checks for flexure, shear, tension, compression, torsion, and interaction. All design checks showed the members to be OK and within allowable ratios according to the specified design code ANSI/AISC 360-05 LRFD. Sections and material properties are also provided for each member.
The document summarizes the design results of a pitched truss with 15 meters length and 3 meters height composed of 28 vertical and diagonal web members and bottom and top chord members. The maximum axial force is 1.64 tons in the top chord member and the maximum shear is 0.06 tons and moment is 0.03 ton-meters in the top chord member. The bottom chord member meets the design criteria with a ratio of 0.05 under the critical load case of 1.4 times dead load.
Do you want to get up to speed with the most current release of Oracle Database? If so, this session is for you. You will learn about the most exciting and useful new features of Oracle Database 12c that can make your work as a database developer a lot easier. There is more to Oracle Database 12c than just pluggable databases.
The document contains SQL commands that create tables, insert data, and perform queries on the tables. The tables created are studies, software, and programmer. Data is inserted and various queries are run to retrieve, aggregate, and analyze the data. Key information summarized includes:
- Tables were created to store student studies data, software project data, and programmer details.
- Data was inserted into the tables and various queries were run to retrieve, calculate statistics on, and analyze the data across the tables.
- Queries included finding averages, minimums, maximums, counts, sums, and using functions like trunc, round, and to_char to manipulate dates and strings.
This document contains configuration information for the Windows boot process. It describes the Windows Boot Manager as the main boot loader, along with the Windows Boot Loader, Resume from Hibernate application, and Windows Memory Tester. It also includes global settings that are inherited by components like debug settings.
Dbms plan - A swiss army knife for performance engineersRiyaj Shamsudeen
This document discusses dbms_xplan, a tool for performance engineers to analyze execution plans. It provides options for displaying plans from the plan table, shared SQL area in memory, and AWR history. Dbms_xplan provides more detailed information than traditional tools like tkprof, including predicates, notes, bind values, and plan history. It requires privileges to access dictionary views for displaying plans from memory and AWR. The document also demonstrates usage examples and output formats for dbms_xplan.analyze.
The document describes a test that was run to determine if the contiguity of table extents impacts performance. The test procedure created tables with contiguous and discontiguous extents in different tablespaces and measured the time to select and delete records. The results showed little performance difference between contiguous and discontiguous extents, between large and small extents, or between dictionary-managed and locally managed tablespaces. On average, selecting records took around 2-3 seconds and deleting records took around 45-55 seconds, with no significant performance impacts from extent contiguity.
Hyundai r55 w 9 wheel excavator service repair manualsoeldksejdksem
This document section provides instructions for disassembling and assembling the travel motor of an excavator. It includes the following:
1. Removal and installation instructions, noting that all hydraulic hoses must be disconnected before removing the travel motor assembly.
2. An overview of the main components of the travel motor unit and control unit.
3. A list of standard tightening torques for reassembling the travel motor.
4. General precautions for disassembling and reassembling the travel motor, emphasizing the need to check items for inspection before disassembly and clean all parts thoroughly.
These slides are from OpenWorld 2018. We covered
- conventional CONNECT BY syntax in Oracle
- extensions that were introduced in more recent versions
- the recursive WITH clause
pstack, truss etc to understand deeper issues in Oracle databaseRiyaj Shamsudeen
The document discusses various process monitoring and debugging tools for Oracle databases like truss, pstack and pfiles. It provides examples of using truss to trace system calls of processes like PMON and DBWR. It demonstrates how truss can be used to see shared memory segment creation during database startup and process attachment. It also summarizes the process creation steps seen during connection creation in Oracle.
This document discusses range and hash partitioning in Oracle databases. It provides examples of creating tables partitioned by range on date columns and hash on number columns. Benefits discussed include partition pruning for performance and even distribution of data for hash partitioning. Multi-column range partitioning and improvements in 11g are also covered.
The document contains details of SQL execution plans and statistics for queries run against tables A and B. It includes the execution plan details showing the operations performed at each step including table access methods and indexes used. It also shows statistics on the performance of the queries such as elapsed time, CPU time, number of executions and rows processed.
The document contains SQL statements and execution plans for counting records in a table where the ID is between 1 and 10 and the status is either '00' or '01'. It shows that for a status of '00' there are 10000 records, but for a status of '01' there are 0 records. Execution plans and statistics are provided with each statement to analyze the performance and resource usage.
The document describes the design of an operational amplifier using MOSFET transistors. It specifies the design rules and parameters to be used, including junction geometries, device properties, and operating specifications. It then presents the design of a common-source gain stage, where the input voltage is calculated to be 0.881 mV for an output of 2.5 V, which is verified through simulation and analytical calculation.
This document provides safety precautions, warnings, service navigation instructions and specifications for a Panasonic CD Stereo System model SA-AK280EB, SA-AK280EG, SA-AK280EP. It outlines general safety guidelines, protection circuitry information, procedures for checking for electric leaks, and locations of safety parts. The document also provides troubleshooting guides, diagrams, testing procedures and part replacement instructions for servicing the stereo system.
This JCL restores datasets from a DFDSS dump for the CA Unicenter/TNG Framework product version 2.2. It includes multiple steps to restore target datasets, distribution datasets, SMP/E libraries, the customer file, HFS files, and Book Manager files to their appropriate volumes after replacing site-specific variables. It also contains steps to update the SMP/E CSI and zones after restoration is complete.
This document contains a list of serial numbers and keys for various software programs including: MS Office 2007, MS Office 2003, Nero 7, Windows XP SP-2, Adobe Pagemaker 7, Photoshop 7, MATLAB, Partition Magic, Alcohol, Folder Locket, Counter Strike, Need for Speed Hot Pursuit 2, and many antivirus programs from AVG such as AVG Internet Security 7.5, AVG Anti-Spyware 7.5, and AVG Antivirus 7.5.
The document summarizes the design results of a pitched truss with 15 meters length and 3 meters height composed of 28 vertical and diagonal web members and bottom and top chord members. The maximum axial force is 1.64 tons in the top chord member and the maximum shear is 0.06 tons and moment is 0.03 ton-meters in the top chord member. The bottom chord member meets the design criteria with a ratio of 0.05 under the critical load case of 1.4 times dead load.
The report finds all custom objects in the R3TR system that have a development class and object type specified by the user. It displays the objects in an ALV grid or downloads the data to a CSV file. It retrieves object data from the TADIR table and transaction code data from the TSTC table, then either displays it using REUSE_ALV_GRID_DISPLAY or fills a table for downloading using GUI_DOWNLOAD.
The document provides design details for a supported conical roof tank, including summaries of shell course design, roof design, bottom design, and anchor bolt design. Key specifications include a tank diameter of 31.16 feet, shell height of 35.43 feet, and material thicknesses between 0.315 and 0.3937 inches. The roof requires a minimum thickness of 0.3055 inches and has 14 rafters. The bottom has a flat annular design.
The document provides design details for a supported conical roof tank, including summaries of shell course design, roof design, bottom design, and anchor bolt design. Key specifications include a tank diameter of 31.16 feet, shell height of 35.43 feet, and material thicknesses between 0.315 and 0.3937 inches. The roof requires a minimum thickness of 0.3055 inches and has 14 rafters. The bottom has a flat annular design.
This document contains software keys and serial numbers for various software programs, including:
- MS Office 2007 and 2003
- Nero burning software
- Windows XP service packs
- Antivirus software from AVG including AVG Antivirus, AVG Internet Security, and AVG Anti-Spyware
- Software from Macromedia including Dreamweaver, Flash, and Fireworks
This report defines variables and data objects needed to display an ALV grid and handle user interactions. It retrieves data from a table into an internal table based on a user-selected table name and number of lines. It displays the data in an ALV grid and handles function codes to copy a selected line to a new internal table or save modified data back to the original table.
This document is the title sheet for a solar electric system project installation at a residence. It includes a vicinity map, scope of work, drawing index, permit conditions, and codes to be followed. The project involves installing a roof-mounted photovoltaic system consisting of 33 panels that will be interconnected to but not export electricity to the utility grid. The system will be designed and installed per the National Electrical Code and utility interconnect requirements.
This document provides a 3-page summary of a service manual for a DVD/video CD/CD player (model DVP-S9):
1) It outlines the disassembly process for the player in 7 steps and provides instructions and diagrams for removing each major component.
2) It describes the test mode for changing the color system and performing a cold reset to clear all stored data.
3) It includes a parts identification section that lists the main components of the player and remote control with descriptions.
This document provides a table of contents and chapters on useful SAP transactions, programs, and general ABAP programming tips. Chapter 1 lists transactions for EDI, IDoc administration, requirements coding, sales order processing, and general transactions. Chapter 2 describes useful function modules, programs, includes and fields. Following chapters cover general programming, reports, IDoc programming, object programming, ALV grid control, Basis errors and an index. The document serves as a reference for ABAP developers needing guidance on common tasks.
The document describes a test that was run to determine if the contiguity of table extents impacts performance. The test procedure created tables with contiguous and discontiguous extents in different tablespaces and measured the time to select and delete records. The results showed little performance difference between contiguous and discontiguous extents, between large and small extents, or between dictionary-managed and locally managed tablespaces. On average, selecting records took around 2-3 seconds and deleting records took around 45-55 seconds, with no significant performance impacts from extent contiguity.
Hyundai r55 w 9 wheel excavator service repair manualsoeldksejdksem
This document section provides instructions for disassembling and assembling the travel motor of an excavator. It includes the following:
1. Removal and installation instructions, noting that all hydraulic hoses must be disconnected before removing the travel motor assembly.
2. An overview of the main components of the travel motor unit and control unit.
3. A list of standard tightening torques for reassembling the travel motor.
4. General precautions for disassembling and reassembling the travel motor, emphasizing the need to check items for inspection before disassembly and clean all parts thoroughly.
These slides are from OpenWorld 2018. We covered
- conventional CONNECT BY syntax in Oracle
- extensions that were introduced in more recent versions
- the recursive WITH clause
pstack, truss etc to understand deeper issues in Oracle databaseRiyaj Shamsudeen
The document discusses various process monitoring and debugging tools for Oracle databases like truss, pstack and pfiles. It provides examples of using truss to trace system calls of processes like PMON and DBWR. It demonstrates how truss can be used to see shared memory segment creation during database startup and process attachment. It also summarizes the process creation steps seen during connection creation in Oracle.
This document discusses range and hash partitioning in Oracle databases. It provides examples of creating tables partitioned by range on date columns and hash on number columns. Benefits discussed include partition pruning for performance and even distribution of data for hash partitioning. Multi-column range partitioning and improvements in 11g are also covered.
The document contains details of SQL execution plans and statistics for queries run against tables A and B. It includes the execution plan details showing the operations performed at each step including table access methods and indexes used. It also shows statistics on the performance of the queries such as elapsed time, CPU time, number of executions and rows processed.
The document contains SQL statements and execution plans for counting records in a table where the ID is between 1 and 10 and the status is either '00' or '01'. It shows that for a status of '00' there are 10000 records, but for a status of '01' there are 0 records. Execution plans and statistics are provided with each statement to analyze the performance and resource usage.
The document describes the design of an operational amplifier using MOSFET transistors. It specifies the design rules and parameters to be used, including junction geometries, device properties, and operating specifications. It then presents the design of a common-source gain stage, where the input voltage is calculated to be 0.881 mV for an output of 2.5 V, which is verified through simulation and analytical calculation.
This document provides safety precautions, warnings, service navigation instructions and specifications for a Panasonic CD Stereo System model SA-AK280EB, SA-AK280EG, SA-AK280EP. It outlines general safety guidelines, protection circuitry information, procedures for checking for electric leaks, and locations of safety parts. The document also provides troubleshooting guides, diagrams, testing procedures and part replacement instructions for servicing the stereo system.
This JCL restores datasets from a DFDSS dump for the CA Unicenter/TNG Framework product version 2.2. It includes multiple steps to restore target datasets, distribution datasets, SMP/E libraries, the customer file, HFS files, and Book Manager files to their appropriate volumes after replacing site-specific variables. It also contains steps to update the SMP/E CSI and zones after restoration is complete.
This document contains a list of serial numbers and keys for various software programs including: MS Office 2007, MS Office 2003, Nero 7, Windows XP SP-2, Adobe Pagemaker 7, Photoshop 7, MATLAB, Partition Magic, Alcohol, Folder Locket, Counter Strike, Need for Speed Hot Pursuit 2, and many antivirus programs from AVG such as AVG Internet Security 7.5, AVG Anti-Spyware 7.5, and AVG Antivirus 7.5.
The document summarizes the design results of a pitched truss with 15 meters length and 3 meters height composed of 28 vertical and diagonal web members and bottom and top chord members. The maximum axial force is 1.64 tons in the top chord member and the maximum shear is 0.06 tons and moment is 0.03 ton-meters in the top chord member. The bottom chord member meets the design criteria with a ratio of 0.05 under the critical load case of 1.4 times dead load.
The report finds all custom objects in the R3TR system that have a development class and object type specified by the user. It displays the objects in an ALV grid or downloads the data to a CSV file. It retrieves object data from the TADIR table and transaction code data from the TSTC table, then either displays it using REUSE_ALV_GRID_DISPLAY or fills a table for downloading using GUI_DOWNLOAD.
The document provides design details for a supported conical roof tank, including summaries of shell course design, roof design, bottom design, and anchor bolt design. Key specifications include a tank diameter of 31.16 feet, shell height of 35.43 feet, and material thicknesses between 0.315 and 0.3937 inches. The roof requires a minimum thickness of 0.3055 inches and has 14 rafters. The bottom has a flat annular design.
The document provides design details for a supported conical roof tank, including summaries of shell course design, roof design, bottom design, and anchor bolt design. Key specifications include a tank diameter of 31.16 feet, shell height of 35.43 feet, and material thicknesses between 0.315 and 0.3937 inches. The roof requires a minimum thickness of 0.3055 inches and has 14 rafters. The bottom has a flat annular design.
This document contains software keys and serial numbers for various software programs, including:
- MS Office 2007 and 2003
- Nero burning software
- Windows XP service packs
- Antivirus software from AVG including AVG Antivirus, AVG Internet Security, and AVG Anti-Spyware
- Software from Macromedia including Dreamweaver, Flash, and Fireworks
This report defines variables and data objects needed to display an ALV grid and handle user interactions. It retrieves data from a table into an internal table based on a user-selected table name and number of lines. It displays the data in an ALV grid and handles function codes to copy a selected line to a new internal table or save modified data back to the original table.
This document is the title sheet for a solar electric system project installation at a residence. It includes a vicinity map, scope of work, drawing index, permit conditions, and codes to be followed. The project involves installing a roof-mounted photovoltaic system consisting of 33 panels that will be interconnected to but not export electricity to the utility grid. The system will be designed and installed per the National Electrical Code and utility interconnect requirements.
This document provides a 3-page summary of a service manual for a DVD/video CD/CD player (model DVP-S9):
1) It outlines the disassembly process for the player in 7 steps and provides instructions and diagrams for removing each major component.
2) It describes the test mode for changing the color system and performing a cold reset to clear all stored data.
3) It includes a parts identification section that lists the main components of the player and remote control with descriptions.
This document provides a table of contents and chapters on useful SAP transactions, programs, and general ABAP programming tips. Chapter 1 lists transactions for EDI, IDoc administration, requirements coding, sales order processing, and general transactions. Chapter 2 describes useful function modules, programs, includes and fields. Following chapters cover general programming, reports, IDoc programming, object programming, ALV grid control, Basis errors and an index. The document serves as a reference for ABAP developers needing guidance on common tasks.
This document summarizes seismic design requirements for non-structural components from the International Building Code and ASCE 7. It provides an overview of requirements for architectural, mechanical, electrical and non-structural systems attached to structures. Key points include defining seismic design categories and use groups, determining applicable seismic forces and displacements, component importance factors, exemptions, and anchorage requirements.
This document is a user manual for the XD/XL series PLC from Wuxi Xinje Electric Co. It provides an overview of the PLC's programming features and instructions. The manual covers topics such as programming languages and modes, basic and applied instructions, functions like high speed counter, communication, PID control, C language function blocks, and sequence blocks. It is intended to help users understand how to program and apply the PLC.
This document provides an overview of HSPICE tutorials available on the class website and instructions for setting up an HSPICE account. It describes the HSPICE simulation software and outlines the general structure and purpose of key sections in HSPICE input files, such as title, setup statements, library includes, netlist, sources, analysis statements, and output. It also summarizes common HSPICE elements, analysis types, and output file formats.
This document provides specifications for designing a monorail system, including material properties, design loads, and analysis assumptions. Structural steel S275 will be used with specified yield strength and elastic modulus. Design loads include vertical and horizontal point loads at the inner and outer rails, increased by 25% for dynamics. Load combinations are defined for the ultimate limit state design considering dead loads, vertical loads, transverse loads, and longitudinal loads. Finite element analysis of the frame was performed in SAP2000 to check deflections under dead and vertical loads.
This COBOL program extracts price information from a DB2 database table for ACR service plans and outputs it to a file with minimal data manipulation. It opens the same cursors multiple times to select different fields for different record types, making processing easier. It includes error handling for empty cursors and outputs informational messages for some. The program extracts data from multiple DB2 tables joined together and limits results to the most current effective and non-expired records.
Similar to KLIMA Software - Some DEMO Results Outputs in SERBIAN Language (20)
KLIMA Software - Some DEMO Results Outputs in SERBIAN Language
1. ==========================================
K L I M A S O F T W A R E - MODUL 1
==========================================
PROGRAM "CODIS" - W8, Ver.4.1, 2013.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
K O E F I C I J E N T I P R O L A Z A T O P L O T E
PROJEKAT :DEMO
OBJEKAT :DEMO
2. KOEFICIJENTI PROLAZA TOPLOTE KLIMA Software - NU str. 1
RB SIFRA K K-DOZ NAZIV ELEMENTA A-U A-S DEB LAMB M NAZIV SLOJA
W/m2K W/m2K W/m2K cm W/mK
--------------------------------------------------------------------------
1 EW 1 0.53 0.80 EXTERNAL WALL 8 23 1.50 1.40 CEMENTNI MALTER
25.00 0.640 TERMOBLOKOVI
1.50 0.190 IZOLAC. MALTER
0.10 0.170 BITUM. PREMAZ
5.00 0.041*MINERALNA VUNA
0.05 203.0 ALU-FOLIJA
2.00 0.920 FASADNE PLOCE
3. KOEFICIJENTI PROLAZA TOPLOTE KLIMA Software - NU str. 2
L E G E N D A :
===============
RB = redni broj elementa konstrukcije
SIFRA = sifra elementa
K = koeficijent prolaza toplote (W/m2K)
K-DOZ = dozvoljeni koeficijent prolaza toplote (W/m2K)
NAZIV ELEMENTA = opis elementa konstrukcije
A-U = koeficijent prelaza toplote - unutrasnji (W/m2K)
A-S = koeficijent prelaza toplote - spoljasnji (W/m2K)
DEB = debljina sloja (cm)
LAMB = koeficijent provodjenja toplote (W/mK)
M = marker sloja predvidjenog za izmenu po potrebi
NAZIV SLOJA = opis sloja prema datoteci "TERMAT"
4. ==========================================
K L I M A S O F T W A R E - MODUL 1
==========================================
PROGRAM "CODIS" - W8, Ver.4.1, 2013.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
D I F U Z I J A V O D E N E P A R E
PROJEKAT :DEMO
OBJEKAT :DEMO
5. DIFUZIJA VODENE PARE KLIMA Software - NU str. 1
RB SIFRA NAZIV ELEMENTA
---- -------- ----------------
1 EW 1 EXTERNAL WALL
TABELA 1 - PRORACUNSKI USLOVI
-----------------------------------------
VARIJANTA: 1 | V L A Z E N J E | S U S E N J E |
|-------------------|-------------------|
| UNUTRA | SPOLJA | UNUTRA | SPOLJA |
------------------------------|---------|---------|---------|---------|
| TEMPERATURA VAZDUHA | 22.0 C | 35.0 C | 18.0 C | 18.0 C |
|-----------------------------|---------|---------|---------|---------|
| RELATIVNA VLAZNOST VAZDUHA | 50.0 % | 95.0 % | 65.0 % | 65.0 % |
|-----------------------------|---------|---------|---------|---------|
| PRIT. ZASICENJA VODENE PARE | 2643 Pa | 5623 Pa | 2064 Pa | 2064 Pa |
|-----------------------------|---------|---------|---------|---------|
| PARCIJALNI PRIT. VOD. PARE | 1322 Pa | 5341 Pa | 1342 Pa | 1342 Pa |
|-----------------------------|-------------------|-------------------|
| RACUNSKO TRAJANJE PROCESA | 60.0 dana | 60.0 dana |
-----------------------------------------------------------------------
6. DIFUZIJA VODENE PARE KLIMA Software - NU str. 2
RB SIFRA NAZIV ELEMENTA
---- -------- ----------------
1 EW 1 EXTERNAL WALL
TABELA 2 - PRORACUN VLAZENJA
RB NAZIV SLOJA DEB MI RD LAMB R TEMP PS PP MK
cm - m W/mK m2K/W C Pa Pa
-------------------------------------------------------------------------
- UNUTRASNJOST 22.00 2643 1322
- PRELAZ TOPLOTE U 0.13 22.89 2790 1322
1 CEMENTNI MALTER 1.50 30.0 0.45 1.40 0.01
22.96 2802 1327
2 TERMOBLOKOVI 25.00 4.0 1.00 0.640 0.39
25.64 3289 1337
3 IZOLAC. MALTER 1.50 6.0 0.09 0.190 0.08
26.18 3396 1338
4 BITUM. PREMAZ 0.10 10000.0 10.00 0.170 0.01
26.22 3404 1448
5 MINERALNA VUNA 5.00 1.0 0.05 0.041 1.22
34.58 5492 1448
6 ALU-FOLIJA 0.05700000.0 350.00 203.0 0.00
34.58 5492 5276
7 FASADNE PLOCE 2.00 300.0 6.00 0.920 0.02
- PRELAZ TOPLOTE S 0.04 34.73 5538 5341
- SPOLJASNJOST 35.00 5623 5341
-------------------------------------------------------------------------
NEMA KONDENZACIJE U KONSTRUKCIJI
KONSTRUKCIJA ZADOVOLJAVA JUS U.J5.600
7. DIFUZIJA VODENE PARE KLIMA Software - NU str. 3
L E G E N D A :
===============
OPISI VAZE ZA TABELE 2 I 3 :
RB = redni broj sloja (od unutra ka spolja)
NAZIV SLOJA = opis sloja prema datoteci "TERMAT"
DEB = debljina sloja (cm)
MI = faktor otpora difuziji vodene pare (-)
RD = relativni otpor difuziji vodene pare (m)
LAMB = koeficijent provodjenja toplote (W/mK)
R = toplotni otpor sloja (m2K/W)
TEMP = temperatura na granici slojeva (step. C)
PS = pritisak zasicenja vodene pare na datoj temp. (Pa)
PP = parcijalni pritisak vodene pare na datoj temp. (Pa)
MK = marker koji oznacava kondenzaciju na datom mestu
8. ==========================================
K L I M A S O F T W A R E - MODUL 1
==========================================
PROGRAM "CODIS" - W8, Ver.4.1, 2013.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
T O P L O T N A S T A B I L N O S T K O N S T R U K C I J A
PROJEKAT :DEMO
OBJEKAT :DEMO
9. TOPLOTNA STABILNOST KONSTRUKCIJA KLIMA Software - NU str. 1
RB SIFRA K K-DOZ NAZIV ELEMENTA SP.MASA FP FP M VP VP M OR JUS
W/m2K kg/m2 MIN MIN
-------------------------------------------------------------------------
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** SI DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** II DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** JI DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** JJ DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** JZ DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** ZZ DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 15 12.7 ** SZ DA
1 EW 1 0.53 0.80 EXTERNAL WALL 486.0 106.4 10 12.7 ** SS DA
-------------------------------------------------------------------------
KONSTRUKCIJA :
--------------
RB NAZIV SLOJA DEB LAMB R S D U
cm W/mK m2K/W W/m2K W/m2K
---------------------------------------------------------
1 CEMENTNI MALTER 1.500 1.400 0.01 14.93 0.16 9.57
2 TERMOBLOKOVI 25.000 0.640 0.39 8.25 3.22 8.25
3 IZOLAC. MALTER 1.500 0.190 0.08 2.75 0.22 5.36
4 BITUM. PREMAZ 0.100 0.170 0.01 4.44 0.03 5.31
5 MINERALNA VUNA 5.000 0.041 1.22 0.59 0.72 0.77
6 ALU-FOLIJA 0.050203.000 0.00192.94 0.00 0.86
7 FASADNE PLOCE 2.000 0.920 0.02 10.49 0.23 3.19
---------------------------------------------------------
10. TOPLOTNA STABILNOST KONSTRUKCIJA KLIMA Software - NU str. 2
L E G E N D A :
===============
TABELA 1 :
RB = redni broj elementa
SIFRA = sifra elementa
K = koeficijent prolaza toplote (W/m2K)
K-DOZ = dozvoljeni koeficijent prolaza toplote (W/m2K)
NAZIV ELEMENTA = opis elementa konstrukcije
SP.MASA = specificna masa elementa konstrukcije (kg/m2)
FP = faktor prigusenja amplitude temperaturske oscilacije
FPMIN = minimalni dozvoljeni faktor prigusenja amplitude
M = marker koji pokazuje da li je FP>FPMIN
VP = vremenski pomak faze temperaturske oscilacije
VPMIN = minimalni dozvoljeni vremenski pomak faze
M = marker koji pokazuje da li je VP>VPMIN
OR = oznaka orijentacije, npr. JI=jugoistok, JJ=jug, itd.
JUS = marker da li zadovoljava (DA) ili ne (NE) JUS U.J5.600
TABELA 2:
RB = redni broj sloja (od unutra ka spolja)
NAZIV SLOJA = opis sloja prema datoteci "TERMAT"
DEB = debljina sloja (cm)
LAMB = koeficijent toplotne provodljivosti mater. sloja (W/mK)
R = toplotni otpor sloja (m2K/W)
S = koefic. upijanja toplote mater. sloja za 24 h (W/m2K)
D = karakteristika toplotne inercije sloja (-)
U = koefic. upijanja toplote povrsine konstrukcije (W/m2K)
11. ==========================================
K L I M A S O F T W A R E - MODUL 2B
==========================================
PROGRAM "CLOAD" - W8, Ver.4.1, 2013.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
P R O R A C U N T O P L O T N I H D O B I T A K A
PROJEKAT : DEMO
OBJEKAT : DEMO
12. PRORACUN TOPLOTNIH DOBITAKA KLIMA Software - NU str. 1
--------------------------------------------------------------------------
PROJEKAT : OBJEKAT :
PROJEKTNI USLOVI :
----------------
METODA : CARRIER
ZAMUCENOST ATMOSFERE : 10.0 %
GEOGRAFSKA SIRINA : 44.0
VISINA : 15 m
TEMPERATURA-LETO,15 SATI : 33.0 C
RASPON DNEVNE TEMPERATURE : 12.8 C
RASPON GODISNJE TEMPERATURE: 48.0 C
OBJEKAT:BLD1- MAKSIMALNO JEDNOVREMENO OPTERECENJE
--------------------------------------------------------------------------
MESEC: 9 VREME:18 POVRSINA: 100.0 m2 ZAPREMINA: 500.0 m3
BROJ LJUDI: 10 SVEZ VAZDUH: 0.0 m3/h
Qsenzibilno = 3565.0 W Qlatentno = 760.0 W Qinsolacija = 1261.0 W
Qtransmisija= 716.0 W Qinfiltrac. = 28.0 W Qventilacija= 0.0 W
Qljudi sen. = 760.0 W Qljudi lat. = 560.0 W Qsvetlo = 500.0 W
Qoprema sen.= 300.0 W Qoprema lat.= 200.0 W Qsvez vazduh= 0.0 W
13. PRORACUN TOPLOTNIH DOBITAKA KLIMA Software - NU str. 2
--------------------------------------------------------------------------
PROJEKAT : OBJEKAT :
GRUPA: S1 - SPRAT 1 - MAKSIMALNO JEDNOVREMENO OPTERECENJE
--------------------------------------------------------------------------
MESEC: 9 VREME:18 POVRSINA: 100.0 m2 ZAPREMINA: 500.0 m3
BROJ LJUDI: 10 SVEZ VAZDUH: 0.0 m3/h
Qsenzibilno = 3565.0 W Qlatentno = 760.0 W Qinsolacija = 1261.0 W
Qtransmisija= 716.0 W Qinfiltrac. = 28.0 W Qventilacija= 0.0 W
Qljudi sen. = 760.0 W Qljudi lat. = 560.0 W Qsvetlo = 500.0 W
Qoprema sen.= 300.0 W Qoprema lat.= 200.0 W Qsvez vazduh= 0.0 W
14. PRORACUN TOPLOTNIH DOBITAKA KLIMA Software - NU str. 3
--------------------------------------------------------------------------
PROJEKAT : OBJEKAT :
==========================================================================
GRUPA: S1-SPRAT 1 PROSTORIJA: PR1 -PROSTORIJA 1 - MAKSIMUM
--------------------------------------------------------------------------
MESEC: 9 VREME:18 POVRSINA: 100.0 m2 ZAPREMINA: 500.0 m3
BROJ LJUDI: 10 UNUTRASNJA TEMPERATURA: 23.0 C
Qsenzibilno = 3565.0 W Qlatentno = 760.0 W Qinsolacija = 1261.0 W
Qtransmisija= 716.0 W Qinfiltrac. = 28.0 W Qventilacija= 0.0 W
Qljudi sen. = 760.0 W Qljudi lat. = 560.0 W Qsvetlo = 500.0 W
Qoprema sen.= 300.0 W Qoprema lat.= 200.0 W
OZN. OR. SIR VIS POVRS. SEN. K SOL.F. DEL-T Q-SENZIB.
m m m2 % W/m2k C W
--------------------------------------------------------------------------
. PS Z 5.00 2.50 12.5 0 2.10 0.35 4.7 1412.0
. ZS Z 10.00 5.00 37.5 0.50 5.9 111.0
. KR KR 10.00 10.00 100.0 0.40 12.1 482.0
15. ==========================================
K L I M A S O F T W A R E - MODUL 3B
==========================================
PROGRAM "FCU-s" - W8, Ver.4.1, 2014.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
I Z B O R F A N - C O I L-a
PROJEKAT : DEMO
OBJEKAT : DEMO
16. F A N C O I L U N I T S KLIMA Software - NU str. 1
-------------------------------------------------------------------------
PROJEKAT : OBJEKAT :
-------------------------------------------------------------------------
PROSTORIJA tu V q Q-d KOM T I P DUZ Q-sen A-fl W-fl Q-inst
C m3 W/m3 W m W L/s L/s W
-------------------------------------------------------------------------
DEMO
............................SPRAT 1 .............................
BLD1S1PR1 23 500 9 4325 1-42JW009 0.93 4325 411 0.21 4325
BLD1S1PR2 23 500 9 4325 1-42JW009 0.93 4325 411 0.21 4325
BLD1S1 GRUPA UKUPNO: 8650 8650
2-42JW009
-------------------------------------------------------------------------
-------------------------------------------------------------------------
BLD1 OBJEKAT UKUPNO: 8650 8650
2-42JW009
=========================================================================
17. F A N C O I L U N I T S KLIMA Software - NU str. 2
-------------------------------------------------------------------------
PROJEKAT : OBJEKAT :
-------------------------------------------------------------------------
PROSTORIJA tu V q Q-d KOM T I P DUZ Q-sen A-fl W-fl Q-inst
C m3 W/m3 W m W L/s L/s W
-------------------------------------------------------------------------
-------------------------------------------------------------------------
-------------------------------------------------------------------------
: 8650 8650
2-42JW009
*************************************************************************
PROJEKTNI USLOVI :
1. TEMPERATURA RAZVODNE VODE : 7. C
2. TEMPERATURA POVRATNE VODE : 12. C
*************************************************************************
18. F A N C O I L U N I T S KLIMA Software - NU str. 3
-------------------------------------------------------------------------
PROJEKAT : OBJEKAT :
L E G E N D A :
===============
T A B E L A Z A F A N C O I L - e
---------------------------------------
PROSTORIJA = oznaka prostorije u objektu
tu = unutrasnja temperatura prostorije (C)
V = zapremina prostorije (m3)
q = specificno toplotno opterecenje (W/m3)
Q-d = proracunsko toplotno opterecenje (W)
KOM = broj Fan Coil Uredjaja - FCU-a (kom)
T I P = tip Fan Coil Uredjaja prema datoteci
DUZ = instalisana duzina Fan Coil Uredjaja (m)
Q-sen = instalisani Senzibilni kapacitet FCU-a (W)
A-fl = protok vazduha na "HIGH" brzini FCU-a (L/s)
W-fl = protok vode kroz FCU (L/s)
Q-inst = instalisani Totalni rashladni kapac. FCU-a (W)
PRIMENJENI TIPOVI FAN COIL UREDJAJA :
*
42JW005 * Carrier - ducted FCU
42JW009 * Carrier - ducted FCU
42JW016 * Carrier - ducted FCU
19. ==========================================
K L I M A S O F T W A R E - MODUL 4
==========================================
PROGRAM "ACPIPE" - W8, Ver.4.1, 2014.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
P R O R A C U N C E V N E M R E Z E
PROJEKAT : DEMO
SISTEM : DEMO
20. PRORACUN CEVNE MREZE KLIMA Software - NU str. 1
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
PROJEKTNI USLOVI :
----------------
1. UKUPAN INSTALISANI KAPACITET : 18200. W
2. TEMPERATURA RAZVODNE VODE : 90. C
3. TEMPERATURA POVRATNE VODE : 70. C
4. NAJNEPOVOLJNIJI STRUJNI KRUG - NNSK : V2 4
5. JEDINICNI PAD PRITISKA R U NNSK : 60. Pa/m
6. ZADAT PRITISAK ZA DIMENZIONISANJE : Pa
7. UTICAJ GRAVITACIONOG NAPORA : 0. %
8. SISTEMSKI PODATAK ZA APS. HRAP. CEVI : 0.045 mm
9. SISTEMSKI PODATAK ZA MAX. REDUKC. BV : 0
10. SISTEMSKI PODATAK ZA TACNOST REG. BV : 0.10
PODACI O MREZI :
--------------
1. UKUPAN BROJ VERTIKALA : 2
2. UKUPAN BROJ DEONICA : 10
3. BROJ DEONICA U HOR. MREZI : 2
4. BROJ DEONICA SA BAL. VENT. : 6
5. BROJ DEONICA SA GR. TELIMA : 4
GLAVNI REZULTATI :
----------------
1. UKUPAN PROTOK U SISTEMU : 805. l/h
2. POTREBAN PRITISAK PUMPE : 22430. Pa
25. PRORACUN CEVNE MREZE KLIMA Software - NU str. 6
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
HORIZONTALNA MREZA
------------------
----------------------------------------------------------------------------
DEONICA Q DN-N BRZ DUZ R DPTR DPL LK TIP DN POZ DPBV OTV
W mm m/s m Pa/m Pa Pa BV BV BV BV Pa %
----------------------------------------------------------------------------
H1 18200 25 0.40 10.0 81 815 9574
H1A 18200 25 0.40 2.0 81 163 2754
----------------------------------------------------------------------------
26. PRORACUN CEVNE MREZE KLIMA Software - NU str. 7
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
VERTIKALA : V1
------------------
----------------------------------------------------------------------------
DE Q DN-N BRZ DUZ R DPTR DPL LK TIP DN POZ DPBV OTV GRV VISAK
W mm m/s m Pa/m Pa Pa BV BV BV BV Pa % Pa Pa
----------------------------------------------------------------------------
1 8220 20 0.29 20.0 62 1245 1753 P TIP-1 20 3.20 1626 53
2 3610 15 0.23 4.0 57 228 5748 R TIP-3 15 3.00 3050 37 0 152
P TIP-5 15 4.40 2544 88
3 4610 15 0.29 6.0 89 533 21
4 4610 15 0.29 4.0 89 356 5199 R TIP-3 15 8.00 2632 100 0 19
P TIP-5 15 5.00 2318 100
----------------------------------------------------------------------------
VERTIKALA : V2
------------------
----------------------------------------------------------------------------
DE Q DN-N BRZ DUZ R DPTR DPL LK TIP DN POZ DPBV OTV GRV VISAK
W mm m/s m Pa/m Pa Pa BV BV BV BV Pa % Pa Pa
----------------------------------------------------------------------------
1 9980 20 0.36 20.0 89 1779 641 P TIP-1 20 6.00 455 100
2 4610 15 0.29 4.0 89 356 6204 R TIP-3 15 4.00 3399 50 0 145
P TIP-5 15 4.90 2555 98
3 5370 20 0.19 6.0 29 172 9
4 5370 20 0.19 4.0 29 115 6409 R TIP-3 20 8.00 4130 100 0 0
P TIP-5 20 5.00 2170 100
----------------------------------------------------------------------------
27. PRORACUN CEVNE MREZE KLIMA Software - NU str. 8
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
SPECIFIKACIJA MATERIJALA
=========================
STANDARDNE CEVI
----------------
-------------------------------------------
DN OZN DSP DEB DUZINA MASA
mm CEVI mm mm m kg
-------------------------------------------
15 1/2 21.30 2.80 18.0 22.7
20 3/4 26.70 2.90 50.0 84.0
25 1" 33.40 3.40 12.0 30.0
-------------------------------------------
30. PRORACUN CEVNE MREZE KLIMA Software - NU str. 11
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
L E G E N D A
=============
HORIZONTALNA MREZA / VERTIKALE
------------------------------
DEONICA/DE = OZNAKA DEONICE U HOR-VER MREZI
Q = TOPLOTNO OPTERECENJE DEONICE (W)
DN = NAZIVNI PRECNIK CEVI (mm)
N = REDNI BROJ CEVI AKO IMA VISE ISTIH DN
BRZ = BRZINA VODE U DEONICI (m/s)
DUZ = UKUPNA DUZINA DEONICE (RAZ+POV) (m)
R = JEDINICNI PAD PRITISKA OD TRENJA (Pa/m)
DPT = PAD PRITISKA OD TRENJA (Pa)
DPL = PAD PRITISKA OD LOKALNIH OTPORA (Pa)
LK BV = LOKACIJA BV : R-RAZVOD, P-POVRAT
TIP BV = TIP BV - PREMA DATOTECI BALVENT
DN BV = NAZIVNI PRECNIK BV (mm)
POZ BV = POZICIJA REGULACIJE BV
DPBV = PAD PRITISKA U BV SA DATOM POZICIJOM (Pa)
OTV = OTVORENOST BV 0 - 100 (%)
GRV = UTICAJ GRAVITACIJE ZA STRUJNI KRUG (Pa)
VISAK = VISAK PRITISKA POSLE BALANSIRANJA (Pa)
31. ==========================================
K L I M A S O F T W A R E - MODUL 5
==========================================
PROGRAM "ACDUCT" - W8, Ver.4.1, 2014.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
P R O R A C U N V A Z D U S N I H K A N A L A
PROJEKAT : DEMO
SISTEM : DEMO
32. PRORACUN VAZDUSNIH KANALA KLIMA Software - NU str. 1
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
PROJEKTNI USLOVI :
----------------
1. UKUPAN INSTALISANI PROTOK : 500. L/s
2. TEMPERATURA VAZDUHA U KANALU : 13. C
3. TEMPERATURA PROSTORIJE/OKOLINE : 23. C
4. NAJNEPOVOLJNIJI STRUJNI KRUG - NNSK : V1 2
5. JEDINICNI PAD PRITISKA R U NNSK : 0.50 Pa/m
6. ZADAT PRITISAK ZA DIMENZIONISANJE : Pa
7. UTICAJ GRAVITACIONOG NAPORA : 0. %
8. SISTEMSKI PODATAK ZA APS.HRAP.KANALA : 0.045 mm
9. SISTEMSKI PODATAK ZA MAX. REDUKC. CD : 0
10. SISTEMSKI PODATAK ZA TACNOST REG. CD : 0.10
PODACI O MREZI :
--------------
1. UKUPAN BROJ VERTIKALA : 1
2. UKUPAN BROJ DEONICA : 4
3. BROJ DEONICA U HOR. MREZI : 1
4. BROJ DEONICA SA CONT. DAMP. : 3
5. BROJ DEONICA SA DIFUZORIMA : 2
GLAVNI REZULTATI :
----------------
1. UKUPAN PROTOK U SISTEMU : 500. L/s
2. POTREBAN PRITISAK VENTILATORA : 144. Pa
38. PRORACUN VAZDUSNIH KANALA KLIMA Software - NU str. 7
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
HORIZONTALNA MREZA
------------------
----------------------------------------------------------------------------
DEONICA V DN BRZ DUZ R DPTR DPL LK TIP DN POZ DPCD OTV
L/s mm m/s m Pa/m Pa Pa CD CD CD CD Pa %
----------------------------------------------------------------------------
H1 500 400 4.0 5.0 0.44 2 65
----------------------------------------------------------------------------
39. PRORACUN VAZDUSNIH KANALA KLIMA Software - NU str. 8
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
VERTIKALA : V1
------------------
----------------------------------------------------------------------------
DE V DN BRZ DUZ R DPTR DPL LK TIP DN POZ DPCD OTV GRV VISAK
L/s mm m/s m Pa/m Pa Pa CD CD CD CD Pa % Pa Pa
----------------------------------------------------------------------------
1 500 400 4.0 10.0 0.44 4 24 R VAV 400 REG 14
2 250 300 3.5 5.0 0.51 3 46 R VCD 300 REG 11 0 0
3 250 325 3.0 5.0 0.34 2 46 R VCD 325 REG 22 0 0
----------------------------------------------------------------------------
40. PRORACUN VAZDUSNIH KANALA KLIMA Software - NU str. 9
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
SPECIFIKACIJA MATERIJALA
=========================
STANDARDNI KANALI
-----------------
------------------------------------------------------------------
SPIRO-DN INCH RECT-EQVIV. DSP DEB DUZINA MASA
mm mm X mm mm mm m kg
------------------------------------------------------------------
300 12" 300 X 250 301.20 0.60 5.0 28.2
325 13" 350 X 250 326.60 0.80 5.0 33.3
400 16" 450 X 300 401.60 0.80 15.0 150.2
------------------------------------------------------------------
LOKALNI OTPORI
--------------
----------------------------------------------------------------------------
SIF NAZIV LOKO PRECNICI STANDARD. KANALA
75 100 125 150 175 200 225 250 275 300 325 350 375 400
425 450 475 500 550 600 650 700 750 800 850 900 9501000
1050110011501200125013001350140014501500
----------------------------------------------------------------------------
9R 90 bend,round.s. 0 0 0 0 0 0 0 0 0 0 1 0 0 3
0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
DS Diffuser, Supply 0 0 0 0 0 0 0 0 0 1 1 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
SA Sound Attenuator 0 0 0 0 0 0 0 0 0 0 0 0 0 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0
----------------------------------------------------------------------------
42. PRORACUN VAZDUSNIH KANALA KLIMA Software - NU str. 11
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
L E G E N D A
=============
KANALSKA - HORIZONTALNA MREZA / VERTIKALE
-----------------------------------------
DEONICA/DE = OZNAKA DEONICE U HOR-VER KANALSKOJ MREZI
V = VAZDUSNI PROTOK U DEONICI (L/s)
DN = NAZIVNI PRECNIK KANALA (mm)
BRZ = BRZINA VAZDUHA U DEONICI (m/s)
DUZ = UKUPNA DUZINA DEONICE (m)
R = JEDINICNI PAD PRITISKA OD TRENJA (Pa/m)
DPTR = PAD PRITISKA OD TRENJA (Pa)
DPL = PAD PRITISKA OD LOKALNIH OTPORA (Pa)
LK CD = LOKACIJA CD : R-RAZVOD, P-POVRAT
TIP CD = TIP CD - PREMA DATOTECI CONTROL. DAMPERI
DN CD = NAZIVNI PRECNIK CD (mm)
POZ CD = POZICIJA REGULACIJE CD
DPCD = PAD PRITISKA U CD SA DATOM POZICIJOM (Pa)
OTV = OTVORENOST CD 0 - 100 (%)
GRV = UTICAJ GRAVITACIJE ZA STRUJNI KRUG (Pa)
VISAK = VISAK PRITISKA POSLE BALANSIRANJA (Pa)
43. ==========================================
K L I M A S O F T W A R E - MODUL 6
==========================================
PROGRAM "ACBOQ" - W8, Ver.4.1, 2013.
==========================================
VL.KOPIJE: KLIMA Software - NU
==========================================
P R E D M E R I P R E D R A C U N - B O Q
PROJEKAT : DEMO
SISTEM : DEMO
44. PREDMER I PREDRACUN KLIMA Software - NU str. 1
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
1. G R E J N A T E L A
========================
1.1. RADIJATORI
---------------
GRUPA: TK TERMIK-ZRENJANIN - Supply and Installation of
Heating Bodies (radiators) as per drawings and
specifications requirements.
TK-600/160 7.2 m2 X 10.0 USD /m2 = 72.0
TK-800/160 30.1 m2 X 10.0 USD /m2 = 301.0
--------------------------
SUBTOTAL: 373.0 USD
1.2. KONZOLE
------------
CONSOLES - Supply and Installation
16 Pcs X 1.0 USD /Pcs= 16.0
1.3. DRZACI
-----------
SUPPORTS - Supply and Installation
12 Pcs X 1.0 USD /Pcs= 12.0
==========================================
GREJNA TELA UKUPNO : 401.0 USD
2. C E V N A M R E Z A
========================
2.1. CEVI - VODA
----------------
STANDARD PIPES - Supply and Installation of
black steel seemless pipes SCH 40 complete
as per drawings and specification requirements.
DN 15 21.30 X 2.80 18.0 m X 10.0 USD /m = 180.0
DN 20 26.70 X 2.90 50.0 m X 10.0 USD /m = 500.0
DN 25 33.40 X 3.40 12.0 m X 10.0 USD /m = 120.0
--------------------------
SUBTOTAL: 800.0 USD
2.2. CEVI - ODZRAKA
-------------------
STANDARD PIPES - Supply and Installation of
black steel seemless pipes SCH 40 complete
as per drawings and specification requirements.
DN 20 26.70 X 2.90 100.0 m X 10.0 USD /m = 1000.0
2.3. MATERIJAL
--------------
Other materials related to the Installation of
Pipes system (pipes storage, cleaning, welding,
supporting, etc.).
800.0USD X 50.0 %/poz= 400.0
==========================================
CEVNA MREZA UKUPNO : 2200.0 USD
45. PREDMER I PREDRACUN KLIMA Software - NU str. 2
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
3. B A L A N S N I V E N T I L I
==================================
3.1. SIFRA: SVK.KS BALANCING VALVE - Supply and Installation
DN 20 2 Pcs X 10.0 USD /Pcs= 20.0
3.2. SIFRA: RVK.UG BALANCING VALVE - Supply and Installation
DN 15 3 Pcs X 10.0 USD /Pcs= 30.0
DN 20 1 Pcs X 10.0 USD /Pcs= 10.0
-----------------
40.0 USD
3.3. SIFRA: RNK.UG BALANCING VALVE - Supply and Installation
DN 15 3 Pcs X 10.0 USD /Pcs= 30.0
DN 20 1 Pcs X 10.0 USD /Pcs= 10.0
-----------------
40.0 USD
==========================================
BALANSNI VENTILI UKUPNO : 100.0 USD
4. O D Z R A K A
==================
4.1. ODZRACNI VENTILI
---------------------
Supply and Installation of Air Release Valves
DN 15 2 Pcs X 10.0 USD /Pcs= 20.0
4.2. ODZRACNI SUDOVI
--------------------
SIF:AIRVESSEL Supply and Installation of Air Vessels complete
with all required materials for installation and
successful operation.
2 Pcs X 100.0 USD /Pcs= 200.0
==========================================
ODZRAKA UKUPNO : 220.0 USD
5. P O V R S I N S K A O B R A D A
====================================
5.1. IZOLACIJA
--------------
SIFRA: AI Supply and Installation of Insulation complete
with all required materials in accordance with
specifications.
DEB: 25.0 3.1 m2 X 10.0 USD /m2 = 31.0
5.2. BOJENJE
------------
Supply and application of all required materials
for pipes cleaning, priming and final painting
in accordance with specifications.
CEVNA MREZA 5.4 m2 X 10.0 USD /m2 = 54.0
46. PREDMER I PREDRACUN KLIMA Software - NU str. 3
----------------------------------------------------------------------------
PROJEKAT : SISTEM :
----------------------------------------------------------------------------
==========================================
POVRSINSKA OBRADA UKUPNO: 85.0 USD
6. O S T A L I R A D O V I
============================
6.1. PUMPS Supply and Installation of Pumps.
100.0 USD /tot= 100.0
6.2. HEADERS Supply and Installation of Headers.
100.0 USD /tot= 100.0
6.3. H-EXCHANGE Supply and Installation of HEAT EXCHANGERS
100.0 USD /tot= 100.0
6.4. CHEMICALS Supply and Installation of Chemical dosing
equipment, complete with Chemicals required for
1 year (for warranty period) as per the drawings
and specification requirements.
10.0 USD /tot= 10.0
6.5. BMS Supply and Installation of BMS system.
100.0 USD /tot= 100.0
6.6. TESTING TESTING, BALANCING AND COMISSIONING
100.0 USD /tot= 100.0
==========================================
OSTALI RADOVI UKUPNO : 510.0 USD
============================================================================
SVE POZICIJE UKUPNO : 3515.9 USD
============================================================================