This document provides guidance on handling and installing refractory products like ladle shrouds, stoppers, and sub entry nozzles (SENs). It outlines proper installation procedures and common failure points. Key points include carefully handling the ladle shroud to prevent damage, ensuring the shroud remains vertical during casting, and thoroughly cleaning the shroud between casts. For stoppers, the document emphasizes installing and positioning the stopper correctly to minimize risk of breakage during casting operations.
The document provides guidelines for properly assembling flanged pipe joints to prevent leaks. Key steps include:
1. Ensuring proper alignment of flanges and insertion of gaskets without damage.
2. Gradually drawing flanges together with a mechanical device to compress gaskets evenly.
3. Tightening bolts in a star pattern and increasing torque levels until bolts no longer turn to apply sufficient residual preload and compensate for operating conditions.
This document describes Archer's new LOCK series of well suspension plugs that provide absolute protection and a gas-tight seal. The LOCK plugs comprise four variations (SAFELOCK, TIMELOCK, STORMLOCK, LASTLOCK) tailored for different well suspension applications ranging from short-term to permanent abandonment. Key features include being independently certified as gas-tight seals, having a 100% retrieval record, and providing high operational efficiency through rapid deployment and resetting without needing to trip drill pipe.
The document provides instructions for installing, operating, and maintaining a wire rope cutter tool. It describes the tool's specifications for cutting wire ropes up to 22mm in diameter. It provides safety instructions and guidelines for operation, maintenance, and servicing of the tool. Procedures are outlined for replacing parts like the anvil, cutting blade, and hydraulic cylinder seals. The document emphasizes following all safety precautions when using or servicing the tool.
The Merlin Microseal from greyhound Chromatography is a microvalve alternative to the conventional silicone rubber septa used in Gas Chromatography (GC). Its unique design gives it high pressure capability and resisance to wear which results in long life and excellent chromatographic performance. The microseal is available for all major GC manufacturer's instruments.
Ethylene Flexijoint PTFE expansion joints are flexible connectors designed to compensate for misalignment, expansion, contraction, vibration, and shock in process piping. They are made of virgin PTFE resin through a fluoroforming process giving them chemical inertness, wide temperature resistance, and long flex life. Flexijoints are available in sizes from 1/2" to 42" and styles include LimitLink, LimitBolt, AntiSquirm, FlexArmor, Hinged, Universal, and Gimballed to accommodate various piping needs. Common applications include use in piping, pumps, and weigh cells.
ABSTRACT
Protecting bearing from dust and water. Protection
methods like labyrinth rings, rubber seals, felt seals and shaft mechanical seals are described. Choice of the appropriate shaft seal and seal configurations to protect against dust and water ingress is critical. Numerous shaft seal designs suited to contaminated conditions are reviewed.
If you want to see what free maintenance flyers might come up in the future, or want to purchase all 150 today, please see the product page below.
http://www.bin95.com/ebooks/CD_contents.htm
Bumperite Waterguards Sealed Scaffold Ties are 35 times stronger than traditional scaffold wire ties, plus they are sealable in just one component. Using Bumperite Waterguards reduces labor costs and is safer and more reliable.
This document provides information on rubber hydraulic seals produced by Trelleborg Seals for dams, tunnels, and other applications. It describes various seal designs like music note, hump, flat, lip, dry dock, Gina-type, Omega-type, and inflatable seals. It also covers specifications for rubber compounds, manufacturing processes, and technical details about teflon coatings and waterstops. Trelleborg Seals are customized for customer requirements and designed to provide reliable sealing for dams and tunnels under water pressure.
The document provides guidelines for properly assembling flanged pipe joints to prevent leaks. Key steps include:
1. Ensuring proper alignment of flanges and insertion of gaskets without damage.
2. Gradually drawing flanges together with a mechanical device to compress gaskets evenly.
3. Tightening bolts in a star pattern and increasing torque levels until bolts no longer turn to apply sufficient residual preload and compensate for operating conditions.
This document describes Archer's new LOCK series of well suspension plugs that provide absolute protection and a gas-tight seal. The LOCK plugs comprise four variations (SAFELOCK, TIMELOCK, STORMLOCK, LASTLOCK) tailored for different well suspension applications ranging from short-term to permanent abandonment. Key features include being independently certified as gas-tight seals, having a 100% retrieval record, and providing high operational efficiency through rapid deployment and resetting without needing to trip drill pipe.
The document provides instructions for installing, operating, and maintaining a wire rope cutter tool. It describes the tool's specifications for cutting wire ropes up to 22mm in diameter. It provides safety instructions and guidelines for operation, maintenance, and servicing of the tool. Procedures are outlined for replacing parts like the anvil, cutting blade, and hydraulic cylinder seals. The document emphasizes following all safety precautions when using or servicing the tool.
The Merlin Microseal from greyhound Chromatography is a microvalve alternative to the conventional silicone rubber septa used in Gas Chromatography (GC). Its unique design gives it high pressure capability and resisance to wear which results in long life and excellent chromatographic performance. The microseal is available for all major GC manufacturer's instruments.
Ethylene Flexijoint PTFE expansion joints are flexible connectors designed to compensate for misalignment, expansion, contraction, vibration, and shock in process piping. They are made of virgin PTFE resin through a fluoroforming process giving them chemical inertness, wide temperature resistance, and long flex life. Flexijoints are available in sizes from 1/2" to 42" and styles include LimitLink, LimitBolt, AntiSquirm, FlexArmor, Hinged, Universal, and Gimballed to accommodate various piping needs. Common applications include use in piping, pumps, and weigh cells.
ABSTRACT
Protecting bearing from dust and water. Protection
methods like labyrinth rings, rubber seals, felt seals and shaft mechanical seals are described. Choice of the appropriate shaft seal and seal configurations to protect against dust and water ingress is critical. Numerous shaft seal designs suited to contaminated conditions are reviewed.
If you want to see what free maintenance flyers might come up in the future, or want to purchase all 150 today, please see the product page below.
http://www.bin95.com/ebooks/CD_contents.htm
Bumperite Waterguards Sealed Scaffold Ties are 35 times stronger than traditional scaffold wire ties, plus they are sealable in just one component. Using Bumperite Waterguards reduces labor costs and is safer and more reliable.
This document provides information on rubber hydraulic seals produced by Trelleborg Seals for dams, tunnels, and other applications. It describes various seal designs like music note, hump, flat, lip, dry dock, Gina-type, Omega-type, and inflatable seals. It also covers specifications for rubber compounds, manufacturing processes, and technical details about teflon coatings and waterstops. Trelleborg Seals are customized for customer requirements and designed to provide reliable sealing for dams and tunnels under water pressure.
The document describes a new line of spray dry nozzles from Spray Nozzle Engineering. The nozzles feature improved hygiene, easier cleaning and changeouts, longer component life, full axial sealing for leakage control, and FEA design for pressure compliance. Key technologies include concentric clasp alignment for wear parts, seal-in-disc orifice discs, compact hi-flo swirl design, optional drip-pro anti-drip valves, and new check valve sealing face systems. The nozzles are available in push-fit and threaded models with various options to suit different applications and budgets.
The Xomox® XLD lined butterfly valves have thick PFA or PTFE liners that provide resistance to permeation, extending product life and improving safety. The valves feature low torque operation enabled by an innovative sealing mechanism and bearings, allowing the use of smaller and more economical actuators. The substantial liners, live-loaded stem sealing system, improved disc design, and other features provide integrity, safety and cost advantages for the valves.
Saflex is a trusted brand for laminated glass interlayers that provides safety, security, acoustic insulation, sustainability, and aesthetic benefits. Laminated glass made with Saflex interlayers meets various codes and standards for hurricane protection, can withstand extreme winds and impacts from missiles, offers seismic protection by preventing glass fallout in earthquakes, and provides advanced security performance over monolithic glass. Saflex has been innovating laminated glass for over 80 years and is used in 50% of automotive and architectural laminated glass applications worldwide.
This document discusses rubber expansion joints and their uses. The key points are:
1. Rubber expansion joints are used to prevent stresses from pipe movement due to temperature changes and vibration, and to compensate for pipe misalignment. They absorb movement to prevent buckling or separation of pipes.
2. They also serve as insulation against noise and vibration transmission between pipes and equipment.
3. There are three basic types of expansion joints described - spool type, tapered, and offset joints. Spool type joints are the most common and handle the greatest range of movement. Tapered and offset joints are used to connect pipes of unequal sizes or with some misalignment.
The document provides instructions for using a Flange BossTM spreader tool to safely open flanges on pipes. Key steps include:
1) Checking that no pressure or materials remain in the line before opening any flanges.
2) Selecting the correct Flange BossTM model for the flange rating size.
3) Loosening bolts and inserting the Flange BossTM into a bolt hole to spread the flanges.
4) Rotating the cam-wedge tool to gradually spread the flanges until the safety stop is reached.
Its very useful book for all the Mechanical Engineers, who are working production side and by this book we know the various types of gaskets and applications.
Developed in Sweden, Nord-Lock washers prevent bolted connections from loosening - even under the most severe vibration and dynamic loads. With the unique wedge-locking technology and high-quality steel, Nord-Lock washers are the safest, most reliable bolt-securing solutions in the world.
The pipe sprayer consists of two air motors. One drives the body around the
central axis and the second drives the cup. The cup motor is set at an angle
into the body, thus as the cup revolves and body rotates a wobble motion is
set up generating a spray pattern inside the pipe. This wobble-
head action produces a reciprocating
fan pattern which enables coating to reach
the back edges formed by pit etc., in corroded
pipes. This avoids having to go through
the pipe in two directions allowing one coat
application.
Take a look at these landscape watering options. Tired of paying for expensive brass valves? Check out the plastic valve options. Save money with rotary nozzles.
The document describes two knife gate valves produced by Keros - the K600HP and K1500 KONCH.
The K600HP is a high performance bi-directional valve for high pressure applications up to 40 bar. It has a rigid body and seal construction for long life. UHMW material guides the gate and protects the seal. The K1500 KONCH is for mining and power plant applications up to 10 bar pressure. It has an abrasion resistant urethane primary seal that can withstand up to 120°C and high corrosion/erosion. Both valves are tested to relevant standards before shipment.
The document describes Excel 440 Super Lubricant, a multipurpose lubricant effective for high stress and high temperature applications. It can be used for chain and wire rope lubrication, cutting tools, bending and punching metals, and as an emergency lubricant for seized parts. The lubricant provides instant lubrication in extreme temperatures and conditions, protects against corrosion, and extends equipment life. It cleans and lubricates while reducing friction.
The document provides information about ORBIT valves, including:
- ORBIT valves use a unique tilt-and-turn design that eliminates seal rubbing for long-term reliable performance where zero leakage and frequent operation are required.
- They are used globally in applications like gas processing plants and molecular sieve systems.
- ORBIT valves are available in a range of sizes, materials, end connections, and can include actuators and instrumentation for complete packages.
- Cameron provides quality assurance, maintenance, and repair services for ORBIT valves.
HP5000 Flue at Mariner Leisure Centre
A project at the Mariner Leisure Centre, which is located not too far from the impressive Falkirk Wheel in Falkirk for our client, SSE, was to to supply, deliver and install a HP 5000 250mmID/350mmOD flue (50 cav) off a Capstone C65 CHP a gas turbine one.
It then rose vertically before turning 87° to run at 3° to the horizontal, with a 90° bend, for approximately 5 metres to connect into a HP 5000 250mmID/300mmOD (25 Cav) drained tee and then rising vertically for approximately 9m to termination.
The document discusses the development of anchored rubber gaskets for concrete tunnel segments. It describes the evolution from early glued gaskets that had poor stability, to anchored gaskets that are integrated directly into the concrete during casting (fourth generation). The latest generation adds a hydrophilic swelling strip that can self-repair gaps or offsets during assembly. Technical specifications and test results are provided for the UG027A anchored gasket with hydrophilic strip, showing its water tightness and ability to maintain contact at various gaps and offsets. Water conditions in Doha are also noted to not negatively impact the EPDM rubber or hydrophilic materials.
Corrocoat Top Hat Nozzle Inserts are manufactured using a mould thus ensuring the consistency of the external diameters, the wall thickness is usually 2.0mm but this can be increased to suit customer requirements.
The document discusses selecting and installing hydraulic hose assemblies properly. It covers important factors like selecting hoses rated for the system's maximum pressure, ensuring chemical compatibility of hoses and fluids, and following proper installation procedures to maximize service life and safety. Improperly assembled hoses can fail and cause injury or damage. The document provides guidelines on hose selection, installation, storage, and safe use.
The document discusses several models of control valves and controllers for industrial process applications. It provides details on the Model 988/989 pneumatic control valves which were designed for chemical plants and corrosive service. It also summarizes the Model 764P pneumatic proportional pressure controller and Model 764T pneumatic temperature controller, noting their reliable and economic nature.
USH / DIAGER ist ein anerkannter Spezialist rund ums professionelle Bohren. Die besondere Geometrie, die sich bei allen Anwendungen von Bohrern vorteilhaft erweist, ist eines der Qualitätsmerkmale bei Diager Betonbohrer. Darum sind diese Werkzeuge häufig die bevorzugte Wahl für Profis auf der Baustelle und in der Industrie. USH hält heute zahlreiche Markenrechte und Patente, es gibt selbstverständlich noch viele weitere Qualitätsmerkmale für Diager Betonbohrer. Wir zeigen Ihnen in dieser Beitrags-Serie auf welche Produktunterschiede Sie achten sollten.
https://luma-handel.at
Ubérisation, Ubériser… ces termes sont souvent utilisés pour
caractériser le changement de paradigme que connaissent
de nombreux marchés, l’inquiétude de certains secteurs de
voir trop rapidement leur modèle de rentabilité bouleversé
par l’apparition d’acteurs innovants. Ces termes provoquent
attraction, réaction, répulsion, ils effraient, fascinent, passionnent ou suscitent l’admiration et l’envie de réagir.
Derrière ce phénomène de communication et de buzz,
dont les médias se sont largement emparés, ces nouveaux
acteurs ne sont ni plus ni moins que des entreprises innovantes qui ont placé réellement le client, ses usages, son
expérience au centre de leur business, pour répondre à des
demandes insatisfaites. Elles partagent toutes un ADN
commun, résolument digital, centré client, centré données
et avec des actifs très légers, remettant sur le devant
de la scène ce que nous avons peut-être trop longtemps
sous-estimé, la valeur du lien entre les individus, entre les
clients.
The document describes a new line of spray dry nozzles from Spray Nozzle Engineering. The nozzles feature improved hygiene, easier cleaning and changeouts, longer component life, full axial sealing for leakage control, and FEA design for pressure compliance. Key technologies include concentric clasp alignment for wear parts, seal-in-disc orifice discs, compact hi-flo swirl design, optional drip-pro anti-drip valves, and new check valve sealing face systems. The nozzles are available in push-fit and threaded models with various options to suit different applications and budgets.
The Xomox® XLD lined butterfly valves have thick PFA or PTFE liners that provide resistance to permeation, extending product life and improving safety. The valves feature low torque operation enabled by an innovative sealing mechanism and bearings, allowing the use of smaller and more economical actuators. The substantial liners, live-loaded stem sealing system, improved disc design, and other features provide integrity, safety and cost advantages for the valves.
Saflex is a trusted brand for laminated glass interlayers that provides safety, security, acoustic insulation, sustainability, and aesthetic benefits. Laminated glass made with Saflex interlayers meets various codes and standards for hurricane protection, can withstand extreme winds and impacts from missiles, offers seismic protection by preventing glass fallout in earthquakes, and provides advanced security performance over monolithic glass. Saflex has been innovating laminated glass for over 80 years and is used in 50% of automotive and architectural laminated glass applications worldwide.
This document discusses rubber expansion joints and their uses. The key points are:
1. Rubber expansion joints are used to prevent stresses from pipe movement due to temperature changes and vibration, and to compensate for pipe misalignment. They absorb movement to prevent buckling or separation of pipes.
2. They also serve as insulation against noise and vibration transmission between pipes and equipment.
3. There are three basic types of expansion joints described - spool type, tapered, and offset joints. Spool type joints are the most common and handle the greatest range of movement. Tapered and offset joints are used to connect pipes of unequal sizes or with some misalignment.
The document provides instructions for using a Flange BossTM spreader tool to safely open flanges on pipes. Key steps include:
1) Checking that no pressure or materials remain in the line before opening any flanges.
2) Selecting the correct Flange BossTM model for the flange rating size.
3) Loosening bolts and inserting the Flange BossTM into a bolt hole to spread the flanges.
4) Rotating the cam-wedge tool to gradually spread the flanges until the safety stop is reached.
Its very useful book for all the Mechanical Engineers, who are working production side and by this book we know the various types of gaskets and applications.
Developed in Sweden, Nord-Lock washers prevent bolted connections from loosening - even under the most severe vibration and dynamic loads. With the unique wedge-locking technology and high-quality steel, Nord-Lock washers are the safest, most reliable bolt-securing solutions in the world.
The pipe sprayer consists of two air motors. One drives the body around the
central axis and the second drives the cup. The cup motor is set at an angle
into the body, thus as the cup revolves and body rotates a wobble motion is
set up generating a spray pattern inside the pipe. This wobble-
head action produces a reciprocating
fan pattern which enables coating to reach
the back edges formed by pit etc., in corroded
pipes. This avoids having to go through
the pipe in two directions allowing one coat
application.
Take a look at these landscape watering options. Tired of paying for expensive brass valves? Check out the plastic valve options. Save money with rotary nozzles.
The document describes two knife gate valves produced by Keros - the K600HP and K1500 KONCH.
The K600HP is a high performance bi-directional valve for high pressure applications up to 40 bar. It has a rigid body and seal construction for long life. UHMW material guides the gate and protects the seal. The K1500 KONCH is for mining and power plant applications up to 10 bar pressure. It has an abrasion resistant urethane primary seal that can withstand up to 120°C and high corrosion/erosion. Both valves are tested to relevant standards before shipment.
The document describes Excel 440 Super Lubricant, a multipurpose lubricant effective for high stress and high temperature applications. It can be used for chain and wire rope lubrication, cutting tools, bending and punching metals, and as an emergency lubricant for seized parts. The lubricant provides instant lubrication in extreme temperatures and conditions, protects against corrosion, and extends equipment life. It cleans and lubricates while reducing friction.
The document provides information about ORBIT valves, including:
- ORBIT valves use a unique tilt-and-turn design that eliminates seal rubbing for long-term reliable performance where zero leakage and frequent operation are required.
- They are used globally in applications like gas processing plants and molecular sieve systems.
- ORBIT valves are available in a range of sizes, materials, end connections, and can include actuators and instrumentation for complete packages.
- Cameron provides quality assurance, maintenance, and repair services for ORBIT valves.
HP5000 Flue at Mariner Leisure Centre
A project at the Mariner Leisure Centre, which is located not too far from the impressive Falkirk Wheel in Falkirk for our client, SSE, was to to supply, deliver and install a HP 5000 250mmID/350mmOD flue (50 cav) off a Capstone C65 CHP a gas turbine one.
It then rose vertically before turning 87° to run at 3° to the horizontal, with a 90° bend, for approximately 5 metres to connect into a HP 5000 250mmID/300mmOD (25 Cav) drained tee and then rising vertically for approximately 9m to termination.
The document discusses the development of anchored rubber gaskets for concrete tunnel segments. It describes the evolution from early glued gaskets that had poor stability, to anchored gaskets that are integrated directly into the concrete during casting (fourth generation). The latest generation adds a hydrophilic swelling strip that can self-repair gaps or offsets during assembly. Technical specifications and test results are provided for the UG027A anchored gasket with hydrophilic strip, showing its water tightness and ability to maintain contact at various gaps and offsets. Water conditions in Doha are also noted to not negatively impact the EPDM rubber or hydrophilic materials.
Corrocoat Top Hat Nozzle Inserts are manufactured using a mould thus ensuring the consistency of the external diameters, the wall thickness is usually 2.0mm but this can be increased to suit customer requirements.
The document discusses selecting and installing hydraulic hose assemblies properly. It covers important factors like selecting hoses rated for the system's maximum pressure, ensuring chemical compatibility of hoses and fluids, and following proper installation procedures to maximize service life and safety. Improperly assembled hoses can fail and cause injury or damage. The document provides guidelines on hose selection, installation, storage, and safe use.
The document discusses several models of control valves and controllers for industrial process applications. It provides details on the Model 988/989 pneumatic control valves which were designed for chemical plants and corrosive service. It also summarizes the Model 764P pneumatic proportional pressure controller and Model 764T pneumatic temperature controller, noting their reliable and economic nature.
USH / DIAGER ist ein anerkannter Spezialist rund ums professionelle Bohren. Die besondere Geometrie, die sich bei allen Anwendungen von Bohrern vorteilhaft erweist, ist eines der Qualitätsmerkmale bei Diager Betonbohrer. Darum sind diese Werkzeuge häufig die bevorzugte Wahl für Profis auf der Baustelle und in der Industrie. USH hält heute zahlreiche Markenrechte und Patente, es gibt selbstverständlich noch viele weitere Qualitätsmerkmale für Diager Betonbohrer. Wir zeigen Ihnen in dieser Beitrags-Serie auf welche Produktunterschiede Sie achten sollten.
https://luma-handel.at
Ubérisation, Ubériser… ces termes sont souvent utilisés pour
caractériser le changement de paradigme que connaissent
de nombreux marchés, l’inquiétude de certains secteurs de
voir trop rapidement leur modèle de rentabilité bouleversé
par l’apparition d’acteurs innovants. Ces termes provoquent
attraction, réaction, répulsion, ils effraient, fascinent, passionnent ou suscitent l’admiration et l’envie de réagir.
Derrière ce phénomène de communication et de buzz,
dont les médias se sont largement emparés, ces nouveaux
acteurs ne sont ni plus ni moins que des entreprises innovantes qui ont placé réellement le client, ses usages, son
expérience au centre de leur business, pour répondre à des
demandes insatisfaites. Elles partagent toutes un ADN
commun, résolument digital, centré client, centré données
et avec des actifs très légers, remettant sur le devant
de la scène ce que nous avons peut-être trop longtemps
sous-estimé, la valeur du lien entre les individus, entre les
clients.
O documento discute os serviços consulares de legalização de documentos no Consulado-Geral do Brasil em Nova York. Ele explica que a legalização autentica a assinatura no documento e permite que ele tenha validade legal no Brasil. Detalha os procedimentos para legalizar diferentes tipos de documentos, incluindo requisitos específicos para documentos escolares, animais de estimação e faturas comerciais.
Vishal Jagtap is pursuing a Bachelor of Engineering degree in Mechanical Engineering from Datta Meghe College of Engineering. He has completed 7 semesters with a grade point average of 8.73/10. He is seeking an entry-level position as a Mechanical Engineer to apply his skills and gain work experience. His academic qualifications include a diploma in Mechanical Engineering from Shivajirao S. Jondhale Polytechnic with 83.64% and SSC from R. J. Thakur English Medium School with 91.27%. His projects include a model of a Kattwyk lift bridge, analysis of a Pelton wheel, a water level indicator, and a compressed air
The Sacred Heart Savings Cooperative was established in 1972 in Galimuyod, Ilocos Sur and has since expanded to over 150 cities/municipalities across 8 provinces. It has over 34,000 members and 25 branches offering savings products, loans for agriculture, business, and other needs, and additional services like printing, events, remittance, and insurance. Under strong leadership, the cooperative has grown to over 1.4 billion in assets and become one of the largest and most awarded cooperatives in the Philippines.
The school has been operating since 1985 and provides elementary and early childhood education. It aims to create a quiet atmosphere for learning and offers various extracurricular activities in the afternoon like basketball, dance, and martial arts. The school strives to educate students holistically by developing their academic skills as well as values like respect for the environment through different projects. It has a mission to provide innovative, high-quality education to help students contribute positively to the world.
The document provides an overview of account based everything and its benefits. It discusses how account based everything coordinates personalized marketing, sales development, sales and customer success efforts to drive engagement and conversion among targeted accounts. This involves orchestrating intelligence-driven programs and campaigns across functions, as well as providing valuable and personalized buyer experiences through coordinated high-effort outreach.
Este documento describe diferentes tipos de funciones polinomiales, incluyendo funciones lineales, cuadráticas, cúbicas, racionales y radicales. Las funciones polinomiales se definen por un polinomio y su dominio incluye todos los números reales. Las funciones lineales son de primer grado y se representan como una línea recta, mientras que las funciones cuadráticas son de segundo grado y se representan como una parábola.
Compressed air vehicles (CAVs) use compressed air instead of gasoline or diesel to power their engines. They store compressed air in high-pressure tanks and use the expansion of the air to drive pistons, instead of fuel combustion. CAVs have the potential to reduce emissions and fuel costs compared to traditional vehicles. Several companies are developing CAV technologies, with the goal of introducing family cars, taxis, and other vehicles powered entirely by compressed air. While CAVs face challenges such as limited driving range, research is ongoing to improve the technology and make compressed air a viable alternative fuel for automobiles.
3. 143 RHI ISO Guidance
Ladle shrouds are susceptible to fracture. Therefore, they have
to be handled with great care and stored in a dry place.
钢包长水口易折断,因此操作时必须格外小心,干燥储存。
The shroud should be kept in the polythene bag prior to use.
This will keep the shroud dry and reduce the risk of moisture
pick up.
使用前钢包长水口存放在聚乙烯包装袋中,防止吸潮,保证
干燥。
The shroud should be carefully handled at all times. Particular
care should be taken when fitting the shroud into the
manipulator. Care should be taken to ensure the shroud is not
scarped along the holding ring, as this will damage the glaze
protection. Also ensure that the shroud is not dropped into the
holding ring as this may also cause damage.
任何时候操作钢包长水口时都必须小心,往夹持器安装长水
口时更应格外小心,确保长水口和支撑环不产生剐蹭,避免
损伤保护釉层,并要确保长水口装入支撑环时不产生较大冲
击,以免损害长水口。
Ladle Shroud Installation
钢包长水口安装
4. 144 RHI ISO Guidance
Prior to fitting the shroud into the manipulator, the following
should be checked:
长水口安装在夹持器前,应作如下检查:
> The shroud should have adequate clearance within the
holding ring, approximate 5mm per side.
> 长水口和支撑环之间应有足够的间隙,每侧大约 5mm 。
> The holding ring should be free of any steel splashes as this
would cause point loading stresses on the shroud and may
restrict the movement of the holding ring.
> 支撑环表面不能存留凸点,避免在该点给长水口施加集
中应力,限制支撑环的运动。
> The pivot points of the shroud ring must be free moving and
well lubricated.
> 支撑环旋转轴部位应滑快,转动自如。
> The holding ring should not be misshapen and provide
adequate clearance for the shroud.
> 支撑环不能变形,确保和长水口间有足够空隙。
Ladle Shroud Installation
钢包长水口安装
5. 145 RHI ISO Guidance
Ladle Shroud Installation
钢包长水口安装
When the shroud is fitted onto the exchangeable nozzle, it is
important to ensure that the shroud remains in a vertical
position. This will ensure a good seal between the shroud and
exchangeable nozzle. This will prevent premature erosion of the
shroud due to air ingress. Preferential erosion of the shroud may
also occur if the shroud is not vertical, i.e. steel flow impacting
on the same area of the bore of the shroud. Keeping the shroud
vertical will also reduce the risk of the shroud breaking due to
point loading stresses.
长水口与钢包下水口配套使用时,长水口保持垂直,以确保
其与钢包下水口之间良好密封,防治空气吸入造成的过早侵
蚀。长水口不垂直,钢流冲刷长水口内壁同一部位造成其过
度侵蚀。保持长水口垂直,也能有助于减小应力集中造成的
颈部断裂。
If the ladle is not a free opener then the shroud should be
removed while the ladle is lanced. When the steel stream has
been established and the tundish is filled to the required level,
the shroud should be refitted to the exchangeable nozzle. Prior
to refitting the shroud, the following points should be checked:
钢包不能自开,需摘下长水口烧氧。引流成功,中间包钢水
升到要求高度后,长水口重新安装在钢包下水口上之前,特
别注意检查如下几点:
6. 146 RHI ISO Guidance
> The throat area and bore of the shroud should be checked and
cleaned if necessary; this will ensure a good seal between
shroud and nozzle and prevent any blowback from the
shroud.
> 检查长水口碗部和内壁,必要时清理干净,确保其与钢
包下水口之间良好密封,防止呕钢。
> The fiber gasket should be checked for damage and replaced
if necessary.
> 检查长水口密封圈是否损坏,必要时更换。
> When refitting the shroud the slide gate should be fully
closed to prevent any steel dribble from entering the throat
area of the shroud, any steel between the shroud and the
nozzle may lead to point loading stresses on the shroud and
prevent a good seal between the shroud and nozzle.
> 安装长水口时,钢包滑板完全关闭,防止钢水滴落在长
水口碗部。长水口与钢包下水口间有冷钢,会形成应力
集中,影响长水口和下水口之间密封。
Ladle Shroud Installation
钢包长水口安装
7. 147 RHI ISO Guidance
Once the cast has been established the shroud should be
immersed in the steel bath to a minimum of 200mm. This will
prevent excess turbulence in the tundish and give good tundish
powder cover; it will also prevent any tundish powder
entrapment in the bore of the shroud.
浇铸时长水口埋入钢水液面下至少 200mm ,防止中包液面
过度波动,中包覆盖剂卷入长水口内。
The movement of the shroud due to the slide gate throttling
should not be restricted by the tundish powder crusting over.
Care should be taken to ensure free movement of the shroud.
长水口随钢包下水口开闭时运动自如,不受中包覆盖剂渣壳
限制。
The ladle shroud is cleaned at the ladle change over by means of
an O2 lance, where possible this should be done with the shroud
in a vertical position. Lancing the shroud in a vertical position
reduces the risk of the molten steel blowing back at the operator.
It also prevents the molten steel running back onto the sealing
face of the shroud. Care should be taken to ensure the throat
area is clean and that the gasket is replaced. This will minimize
the possibility of air ingress while casting and maximize the
shroud life. The bore of the shroud should also be cleaned
thoroughly as any steel skull left in the bore will restrict the steel
flow when the slide gate is opened and may cause a blowback.
换包时长水口用氧枪清理干净,清理时长水口保持垂直,减
少清理时钢花反溅到操作工身上,以及长水口密封面上。特
别注意长水口碗部清理干净,更换新密封圈,这有助于浇铸
时减少空气吸入,延长长水口寿命。长水口内壁也应清理干
净,钢包滑板打开时,任何残留在内壁上的冷钢都会妨碍钢
流,可能造成呕钢。
Ladle Shroud Installation
钢包长水口安装
8. 148 RHI ISO Guidance
Ladle Shroud Failures
长水口事故
A. Cracking Through Flange
A. 凸缘贯穿裂纹
B. Horizontal Break at Collar
B. 颈部横断
C. Thermal Shock Crack
C. 热振裂纹
D. External Corrosion
D. 外部侵蚀
E. Internal Corrosion
E. 内部侵蚀
F. Internal Erosion
F. 内部冲蚀
Symptoms
表现形式
9. 149 RHI ISO Guidance
Ladle Shroud Failures
长水口事故
Causes
原因
A1 Excessive Counter Weight Force
A1 配重力过大
A2 Ladle Nozzle Mismatch
A2 钢包下水口尺寸不匹配
B1 General Condition of Holding Ring
B1 支撑环问题
B2 Insufficient Clearance between Nozzle & Ring
B2 支撑环和长水口间没有足够空隙
C1 Insufficient Oxidized Layer
C1 氧化层太薄
C2 Excessive Moisture Pickup
C2 长水口吸潮
D1 Aggressive Tundish Cover Powder
D1 中包覆盖剂侵蚀性太强
D2 Slag Carry over
D2 钢包下渣
E1 Slag/Powder Entrapment
E1 卷渣
F1 Shroud Not Vertically Positioned
F1 长水口不垂直
10. 1410 RHI ISO Guidance
Stopper Installation
塞棒安装
Stoppers are susceptible to fracture. Therefore, they have to be
handled with great care and stored in a dry place.
塞棒易折断,操作时要格外小心,干燥储藏。
The installation of the stopper rod into the stopper should only
be done with the stopper in a vertical position. The stopper
should also be securely fastened to prevent any movement.
Ensure that the stopper rod has been drilled through to allow any
moisture to be released to atmosphere during preheat prior to
cast.
塞棒螺杆安装时,塞棒要垂直固定。螺杆拧入要保证开浇前
预热时塞棒内潮气能够排出。
The stopper mechanism must be set in middle position
(theoretical movement of 50 mm in both directions).
塞棒机构行程置于中间位(理论上两个方向各 50mm 活动
量)
Place the assembled stopper / stopper rod assembly into the
stopper mechanism cross arm. Adjust the bottom nut to allow
for downward movement / erosion. The stopper is normally set
40 to 50mm high to allow for this.
装配好的塞棒安装到塞棒机构横臂上,调整下部螺母。通常
塞棒安装要留有 40~50mm 向下关闭余量。
11. 1411 RHI ISO Guidance
Stopper Installation
塞棒安装
Tighten the top nut on the stopper rod ensuring that the stopper
is correctly aligned with the SEN, i.e. off seating the stopper to
the back of the SEN in line and toward the stopper control
mechanism by a few millimeters. This slight off setting of the
stopper will allow for any distortion of the tundish during
preheat.
禁锢螺杆上部螺母时确保塞棒与浸入式水口正确对中,即沿
塞棒机构方向,塞棒向浸入式水口后错位几毫米,这一小的
错位可以抵消中包预热时产生的形变
During the installation of the stopper, lifting and lowering of the
stopper should be done gently to prevent any damage to the
stopper nose and SEN seating area.
塞棒安装时轻提慢放,防止损坏塞棒头和水口碗。
12. 1412 RHI ISO Guidance
Stopper Installation
塞棒安装
The stopper should also be in the closed position when moving
the tundish.
中间包移动时塞棒应处于关闭位置。
The delay from end of preheat to the start of casting should be
kept to a minimum to prevent thermal shock cracking of the
stopper and also to prevent the steel stream freezing causing the
stopper to stick in the throat of the SEN. Refer to RHI
recommended preheat cycle.
中间包预热结束到开浇,时间应尽量缩短,防止塞棒热振裂
纹产生,也防止钢水冷凝造成塞棒和浸入式水口粘连。请参
照 RHI 推荐的预热曲线。
The steel stopper rod can be reused after casting. All steel rods
to be reused must be checked to ensure that they are straight and
that the hole in the bore is not blocked. The threads of the rod
should also be cleaned to ensure ease of installation and
tightening.
浇铸后塞棒螺杆可再次使用。所有再次使用的螺杆都要检查
是否平直,吹氩孔有无堵塞,螺筘要清理干净,保证易于安
装和拧紧。
13. 1413 RHI ISO Guidance
Stopper Failures
塞棒事故
Symptoms
表现形式
Breakage 断裂
Erosion/Corrosion 冲蚀 / 侵蚀
Causes Breakage 断裂原因
Fixing End Misalignment 安装不对中
Loose Fixing 安装不紧
Fixing Method 安装方法不对
Main Body Misalignment 本体不对中
Bent Product 塞棒不直
Nose Misalignment 塞棒头不对中
Sticking 粘结
Incorrect Nose Shape 塞棒头形状不正确
Steel Quality 钢种
Powder Quality 保护渣
Misalignment 安装不对中
Steel Flow 钢水流速
Causes Erosion/Corrison
冲蚀 / 侵蚀原因
14. 1414 RHI ISO Guidance
SEN Installation 浸入式水口安装
Sub Entry Nozzles are susceptible to fracture. Therefore, they
have to be handled with great care and stored in a dry place.
浸入式水口易折断,操作时要格外小心,干燥储存。
Ensure the wellblock is clean and free of any tundish rubble, any
hard cement etc will affect seating and alignment of SEN and
split rings.
确保座砖干净,没有各种中包碎块。火泥太硬会影响浸入式
水口和分离环的安装和对中。
Apply Resitect mortar to taper face and bottom support area of
wellblock.
座砖底部和锥面涂抹火泥。
Apply Resitect to inner and outer taper face of split rings. Also
apply Resitect to mating face of split rings.
分离环内外锥面、接合面涂抹火泥。
Insert SEN from bottom of tundish. Push the SEN as high as it
will go to enable split rings to be installed.
浸入式水口从中包底部装入,托起浸入式水口,留出分离环
的安装高度。
After installing split rings, apply Resitect to the taper section of
the SEN and lower the SEN into position in the split rings.
分离环安装后,浸入式水口斜面涂抹火泥,放下浸入式水口
安装到分离环内。
Ensure that the split rings do not rise out of the wellblock. Also
ensure that the split rings are flush with one another at the top
and are pushed down into the wellblock as tight as possible.
分离环不能高出座砖,并且分离环两边上端平齐,将分离环
压入座砖,越紧越好。
15. 1415 RHI ISO Guidance
SEN Installation
浸入式水口安装
Ensure the SEN is also pushed down as tight as possible
into the split rings. Do not hit the SEN with a hammer or
similar object. The easiest way to ensure the tightest fit is
to stand on top of the SEN. Check again after standing on
the SEN that the split rings have not been pushed up from
the wellblock and that both split rings are flush with one
another on the top face.
确认浸入式水口和分离环安装紧密。不能用锤子等敲击浸入
式水口,确认安装紧密的简单的方法是站在浸入式水口上,
下来后检查分离环是否被挤出座砖,分离环两边上端是否平
齐。
Throughout the installation of the SEN someone should be
below the tundish to check the SEN is properly aligned in
the wellblock.
浸入式水口的安装过程中,操作工要在中包底部检查浸入式
水口与座砖准确对中。
As soon as the SEN has been installed some dimensional
checks should be made to check the SEN alignment.
浸入式水口一安装好,用尺子精确测量,检查浸入式水口对
中情况。
Resitect mortar will cure during preheating of SEN.
浸入式水口预热过程中火泥会硬化定型。
16. 1416 RHI ISO Guidance
SEN Installation
浸入式水口安装
Ensure the wellblock is clean and
free of any tundish rubble, any
hard cement etc. will affect
seating and alignment of SEN and
split rings.
确保座砖干净,没有各种中包
碎块。火泥太硬会影响浸入式
水口和分离环的安装和对中。
Apply Resitect to inner and outer
taper face of the split rings
分离环内外锥面涂抹火泥。
The SEN has to be positioned
vertically and with its outlets
parallel to the mould parallel
part. Check length below
tundish. No cavities or channels
are allowed in the putty as air
might be drawn in owing to the
under pressure produced.
浸入式水口安装要垂直,吐出
孔与结晶器平行。检查探出中
包底长度。火泥要涂抹匀实,
不能有孔洞,因为在负压作用
下会吸入空气。
17. 1417 RHI ISO Guidance
SEN Installation
Ensure the SEN is also pushed
down as tight as possible into the
split rings. Do not hit the SEN
with a hammer or similar object.
The easiest way to ensure the
tightest fit is to stand on top of the
SEN.
确认浸入式水口和分离环安装
紧密。不能用锤子等敲击浸入
式水口,确认安装紧密的简单
的方法是站在浸入式水口上。
Throughout the installation of the
SEN someone should be below
the tundish to check the SEN is
properly aligned in the wellblock.
浸入式水口的安装过程中,操
作工要在中包底部检查浸入式
水口与座砖准确对中。
As soon as the SEN has been
installed some dimensional
checks should be made to check
the SEN alignment.
浸入式水口一安装好,用尺子
精确测量,检查浸入式水口对
中情况
18. 1418 RHI ISO Guidance
SEN Failures 浸入式水口事故
A.Symptoms 表现形式
A. Cracking at Tapered Area
A. 缩颈部位裂纹
B. Internal Erosion
B. 内部冲蚀
C. Thermal Shock Crack
C. 热振裂纹
D. Excessive External Corrosion
D. 外部侵蚀
E. Internal Erosion
E. 内部侵蚀
F. Cracking across Port Area
F. 吐出孔部位横裂
19. 1419 RHI ISO Guidance
SEN Failures 浸入式水口事故
Causes 原因
A1. Mismatch between SEN and Well Block
A1. 浸入式水口与座砖尺寸不匹配
B1 Steel Quality 钢种
B2. Irregular Steel Flow 钢流不稳定
C1 Insufficient Preheat Time/Temperature
C1. 预热时间短 / 温度低
C2 Long Delays between Preheat Off to Cast Start
C2. 结束预热后延迟开浇
D1 Oxidation 氧化
D2 Casting Position/Ramping Procedure
D2. 水口浇铸位置 / 水口斜
E1 Steel Quality 钢种
E2 Oxidation 氧化
E3 Casting Procedure/Powder Entrapment
浇铸工艺 / 保护渣卷入
F1 Internal/External Erosion 内部 / 外部冲蚀
F2 Vibration 颤动
20. 1420 RHI ISO Guidance
Heating Instructions
预热说明
Ladle shrouds have an oxidised inner layer that prevents thermal
shocking on initial start up. Therefore, ladle shrouds can be used
for cold start and do not need preheating.
长水口 带氧化层内衬,能防止开浇时产生热振,因此长水口
可以不用预热,冷态下开浇。
Stoppers heat up take place on the casting platform prior to
casting start. During preheating the stopper is open. The stopper
body is mainly heated up by the burners for heating up the tundish
wear lining. The stopper nose is heated up trough the SEN body
by the burners below.
The delay from end of preheat to the start of casting should be
kept to a minimum to prevent thermal shock cracking of the
stopper and also to prevent the steel stream freezing causing the
stopper to stick in the throat of the SEN
塞棒 开浇前在浇铸平台预热,预热时塞棒处于打开位。塞棒
本体和中包一起预热,塞棒头用烧嘴通过浸入式水口内孔预
热。
中间包预热结束到开浇,时间应尽量缩短,防止塞棒热振裂
纹产生,也防止钢水冷凝造成塞棒和浸入式水口粘连。
Thin Slab SEN’s should have cerawool wrapped round it prior to
preheating. This prevents excess heat loss after preheater burner
is closed prior to casting. Burners have to be positioned on both
side of the port to maximize preheating of the SEN body and
stopper nose.
The delay from switching off the SEN burner to start of cast
should be kept to a minimum to prevent thermal shock cracking
of the SEN. The aim, “off gas to start cast” is maximum 3
minutes.
薄板坯水口 预热前包裹石棉毡,防止开浇前预热烧嘴热量过
渡损失。烧嘴布置在吐出孔两侧,最大限度加热水口本体和
塞棒头。
浸入式水口预热结束到开浇,时间应尽量缩短,防止浸入式
水口热振裂纹产生。目标:“停火到开浇时间”最长 3 分钟。