This document summarizes the features and use of GSUN 4th Generation Solar Projection Lamps. The lamps use solar panels to charge an internal battery during the day and power LED lights at night. They have remote controls to set lighting duration and brightness. The lamps are intended for outdoor use in areas like villages, parks and factories that receive sunlight during the day. Installation instructions are provided along with notes on proper solar panel orientation and maintenance.

1. Manufacture of high Quality LED
Industrial Lighting Fittings
CÔNG TY TNHH THIẾT BỊ ĐIỆN MAI MINH NGỌC Website : Gsun.vn
GSUN
®
4TH GENERATION SOLAR PROJECTION LAMP

2. Light sensor control, intelligent lighting, energy saving and environmental protection
Crystalline silicon solar panels, self-charging, no electricity bills
Easy installation, no wiring required
High light efficiency,low energy consumption, low heat, long life, safe and reliable
High temperature powder spraying for mounting bracket, anti-corrosion and anti-
rust, strong and durable
Solar light with remote control, can be different lighting requirements under the
circumstances set their own working hours and brightness.
High luminous efficiency: the use of more than 100LM/W chip, relative to the
traditional high-pressure sodium lamp can save more than 75%
Green environmental protection, no ultraviolet and mercury pollution.
II. PRODUCT CHARACTERISTICS
GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
I. PRODUCT DEFINITION
Solar Projection lamp
Store electric energy, LED as light source, equipped with intelligent controller to
accurately control charging and discharging.
III. APPLICATION DOMAIN
Widely used in villas,courtyards, country lanes,parks, small areas, factories, tourist
attractions, etc. Lighting places with sunshine during the day.
IV. PRODUCT-DRAWING
50W 100W

3. GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
150W 200W
50W 100W
150W 200W

4. GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
V. PRODUCTS PARAMETER

5. GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
VI. PACKING METHOD
Neutral packaging
Side packaging
Inner box packaging

6. VII. MOUNTING DIMENSION INSTRUCTION
GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
50W
100W
150W/200W
1. Insert expansion screws into the wall according to the distance of the bracket screw
holes
2. Fix the lamp body on the wall and lock the expansion screw.
3. The solar panel is installed on the wall,and the angle is adjusted to lock the fixing
screw.
4. Connect the circuit,connect the solar panel and the male bus of the lamp body, and
tighten the waterproof nut.

7. GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
VIII. REMOTE OPERATION INSTRUCTIONS
OPERATING INSTRUCTIONS
1：Assembling each component：The solar panel is fixed on the U-shaped bracket,
the solar panel U-shaped bracket and the projection lamp body U-shaped bracket are
fixed on the wall.
2：Before the solar panel is connected with the lamp holder connecting wire, the key
to turn on the projection lamp, and the select the key according to own request lighting
time, AUTO key is a self-control mode,automatically turn on the lamp at night,
automatically turn off the lamp during the day, 3 hours, 5 hours, 8 hours, the key is a
timing key, turn off the lamp after the appointed time; (has memory function,and
circulates every night). Brightness dimming and brightness dimming are the brightness
adjustment keys (has memory function,and circulates every night).

8. GSUN
®
4TH Generation Solar Projection Lamp
LED Gs - YMTGDT4
MATTERS NEEDING ATTENTION
- Solar street lamp uses solar radiation as energy, whether the sunlight on the solar
panel is abundant or not directly affects the lighting time of the lamp, so when choosing
he installation position of the lamp, it should be far away from the tall building, the wind
speed is large and the solar panel can illuminate the sunlight at any time, and there are
no leaves and other shielding objects;when installing the solar panel, it must face to the
south, tilt upward at 45 angles, it is better to confirm the direction with a compass, and
the sunshine time must be more than 5 hours .
- When using, in order to ensure that solar panels can better accept solar radiation,
please clean the dust on solar panels once every six months.
- The lamp holder and the solar panel connection wire must not “positive pole”and
“negative pole”connect reversely or short circuit, should tighten the wiring waterproof
joint cap, cannot have loose, the connection must be reliable.
- Because each solar street lamp is an independent control system,it is normal to have
a slight difference in switching time.
- Installation and maintenance: Solar street lamp installation and maintenance must
be carried out by the relevant qualified company and technical personnel.
- Parts: Do not use parts that are not recommended by the manufacturer, otherwise it
may cause damage or danger to the system