This document provides instructions for servicing stationary glass components on vehicles. It begins with safety precautions for working with glass and urethane adhesives. Removal and installation instructions are provided for the windshield, liftgate glass, rear door stationary window glass, and rear quarter window glass. The instructions describe cutting urethane seals, cleaning surfaces, applying primer or blackout primer, and securing glass with urethane adhesive or spacers. Adhesives must be allowed to fully cure before operating the vehicle.
The document provides information on standard service procedures for engines, including form-in-place gaskets, honing cylinder bores, measuring crankshaft and connecting rod bearing clearances using Plastigage, repairing damaged or worn threads using a Heli-Coil tap, and servicing a 4.0L engine assembly (short block). It includes diagrams and step-by-step instructions for compression testing, measuring bearing clearance, and honing cylinder bores. Tables of contents and indexes provide page references for additional information on specific engines and procedures.
This document provides standard service information for engines, including general information on form-in-place gaskets, honing cylinder bores, measuring clearances with Plastigage, repairing threads, and servicing the engine assembly. It also outlines procedures for removing hydrostatic lock from an engine, including draining fluids from the cylinders and lubricating the walls before restarting.
This document provides information on diagnosing and repairing squeaks and rattles in vehicles. It outlines a process that involves interviewing the customer, duplicating the noise during a test drive, checking for technical service bulletins, locating and identifying the root cause of the noise. Key steps include narrowing down the noise, removing suspected components, tapping or pushing on components, feeling for vibrations, and looking for loose components or contact marks. The goal is to isolate the source of the noise in a methodical manner.
The document provides information for diagnosing and repairing squeaks and rattles in vehicles. It includes:
- A workflow for diagnosis that begins with interviewing the customer and duplicating the noise.
- Guidelines for inspecting potential problem areas like the instrument panel, center console, doors, trunk, sunroof, and seats.
- A diagnostic worksheet for documenting the inspection and repair work.
- Precautions for working on supplemental restraint systems and performing repairs with power tools near airbag sensors.
This is the Highly Detailed factory service repair manual for the1991 ACURA NSX, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.1991 ACURA NSX Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
General Information
Special Tools
Specifications
Maintenance
Engine
Cooling
Fuel and Emission
Transaxle
Steering
Suspension
Brakes
Body
Heater and Air Conditioner
Electrical
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to have1991 ACURA NSX Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
This document provides an introduction and overview of how to use the service manual. It explains that the manual is divided into 14 sections with tabs corresponding to sections. It describes what is included in each section such as parts diagrams, procedures, inspections, and more. The document also provides important safety information and warnings about working on the SRS airbag system, which requires authorization from an Acura dealer. It notes several SRS components are located near the steering column.
Kawasaki 90 z7b wheel loader service repair manual (serial no. 90c6 5001 and up)ufjjsjkkekmmd
This document provides instructions and guidelines for disassembling, assembling, maintenance, and repair of a Kawasaki 90Z7B wheel loader. It includes sections on general information, maintenance standards, disassembly and reassembly of vehicle body components, operational performance testing, and troubleshooting. Precautions are outlined for tasks like disassembling and assembling parts, tightening bolts and nuts, bleeding air from systems, and releasing hydraulic pressures. Painting specifications are also provided.
Kawasaki 90 z7b wheel loader service repair manual (serial no. 90c6 5001 and up)fjskekdmmmse
This document provides instructions for bleeding air from various systems on a wheel loader, including:
- Bleeding air from the hydraulic oil tank by pushing the air bleed button and removing the tank cap.
- Bleeding air from the hydraulic system after drawing hydraulic oil, replacing filters/pipes, or removing/installing pumps/cylinders.
- Bleeding air from the fuel system by loosening the fuel line fitting at the highest point in the line.
- Bleeding air from the radiator by loosening the radiator cap to release pressure and allow air to escape.
- Bleeding air from the brake system by loosening a fitting at the wheel cylinder to allow air to escape.
The document provides information on standard service procedures for engines, including form-in-place gaskets, honing cylinder bores, measuring crankshaft and connecting rod bearing clearances using Plastigage, repairing damaged or worn threads using a Heli-Coil tap, and servicing a 4.0L engine assembly (short block). It includes diagrams and step-by-step instructions for compression testing, measuring bearing clearance, and honing cylinder bores. Tables of contents and indexes provide page references for additional information on specific engines and procedures.
This document provides standard service information for engines, including general information on form-in-place gaskets, honing cylinder bores, measuring clearances with Plastigage, repairing threads, and servicing the engine assembly. It also outlines procedures for removing hydrostatic lock from an engine, including draining fluids from the cylinders and lubricating the walls before restarting.
This document provides information on diagnosing and repairing squeaks and rattles in vehicles. It outlines a process that involves interviewing the customer, duplicating the noise during a test drive, checking for technical service bulletins, locating and identifying the root cause of the noise. Key steps include narrowing down the noise, removing suspected components, tapping or pushing on components, feeling for vibrations, and looking for loose components or contact marks. The goal is to isolate the source of the noise in a methodical manner.
The document provides information for diagnosing and repairing squeaks and rattles in vehicles. It includes:
- A workflow for diagnosis that begins with interviewing the customer and duplicating the noise.
- Guidelines for inspecting potential problem areas like the instrument panel, center console, doors, trunk, sunroof, and seats.
- A diagnostic worksheet for documenting the inspection and repair work.
- Precautions for working on supplemental restraint systems and performing repairs with power tools near airbag sensors.
This is the Highly Detailed factory service repair manual for the1991 ACURA NSX, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.1991 ACURA NSX Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
General Information
Special Tools
Specifications
Maintenance
Engine
Cooling
Fuel and Emission
Transaxle
Steering
Suspension
Brakes
Body
Heater and Air Conditioner
Electrical
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to have1991 ACURA NSX Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
This document provides an introduction and overview of how to use the service manual. It explains that the manual is divided into 14 sections with tabs corresponding to sections. It describes what is included in each section such as parts diagrams, procedures, inspections, and more. The document also provides important safety information and warnings about working on the SRS airbag system, which requires authorization from an Acura dealer. It notes several SRS components are located near the steering column.
Kawasaki 90 z7b wheel loader service repair manual (serial no. 90c6 5001 and up)ufjjsjkkekmmd
This document provides instructions and guidelines for disassembling, assembling, maintenance, and repair of a Kawasaki 90Z7B wheel loader. It includes sections on general information, maintenance standards, disassembly and reassembly of vehicle body components, operational performance testing, and troubleshooting. Precautions are outlined for tasks like disassembling and assembling parts, tightening bolts and nuts, bleeding air from systems, and releasing hydraulic pressures. Painting specifications are also provided.
Kawasaki 90 z7b wheel loader service repair manual (serial no. 90c6 5001 and up)fjskekdmmmse
This document provides instructions for bleeding air from various systems on a wheel loader, including:
- Bleeding air from the hydraulic oil tank by pushing the air bleed button and removing the tank cap.
- Bleeding air from the hydraulic system after drawing hydraulic oil, replacing filters/pipes, or removing/installing pumps/cylinders.
- Bleeding air from the fuel system by loosening the fuel line fitting at the highest point in the line.
- Bleeding air from the radiator by loosening the radiator cap to release pressure and allow air to escape.
- Bleeding air from the brake system by loosening a fitting at the wheel cylinder to allow air to escape.
Kawasaki 90 z7b wheel loader service repair manual (serial no. 90c6 5001 and up)jfjkskefsmemwe
This document provides guidance on disassembling, assembling, tightening, painting, bleeding air, and preparing a wheel loader for maintenance work. It outlines precautions and procedures for these tasks, including cleaning parts, applying markings, using proper tools, lubricating surfaces, and avoiding contamination. Specified tightening torques and painting colors are also included. The overall document provides technical instructions for servicing and maintaining this particular wheel loader model.
2007 johnson evinrude outboard 9.9 hp service repair manualfjskeksmemedc
This document provides information on safety warnings and trademarks related to outboard engine repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that may be referenced in repair manuals.
2007 johnson evinrude outboard 9.9 hp service repair manualfujdjfjjskekmm
This document provides safety information and instructions for working on Evinrude/Johnson outboard motors. It lists numerous registered trademarks and outlines responsibilities of the manufacturer, dealer, and owner to ensure compliance with EPA emissions regulations. The document also explains various symbols and abbreviations used in the service manual.
2007 johnson evinrude outboard 9.9 hp service repair manualfujsjefjkskekfm
This document provides safety information and instructions for working on Evinrude/Johnson outboard motors. It lists registered trademarks and outlines responsibilities of the manufacturer, dealer, and owner to ensure engine emissions compliance. Symbols used in the manual are defined, including those for electrical components and values. Abbreviations are also listed to clarify terms used.
2007 johnson evinrude outboard 15 hp service repair manualfjkekfmefmm
This document provides information on safety warnings and trademarks related to outboard engine repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that may be referenced in repair manuals.
2007 Johnson Evinrude Outboard 15Hp Service Repair Manualujfjjsjefksekm
This document provides safety information and instructions for working on Evinrude/Johnson outboard motors. It discusses hazards from rotating propellers, exhaust fumes, electrical shock, and fuel. The document emphasizes taking safety precautions like disconnecting batteries, securing the outboard, and working in a ventilated area. It also notes the importance of using authorized replacement parts and following torque specifications.
2007 johnson evinrude outboard 15 hp service repair manualfjsjjfkskeme
This document provides information on safety warnings and trademarks related to outboard engine service and repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that are mentioned in the technical documentation.
2007 johnson evinrude outboard 9.9 hp service repair manualufjjskekmem
This document provides information on safety warnings and trademarks related to outboard engine repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that produce components used in outboard engines.
Android 4.2 Car Stereo Instructions Use ManualAuto pumkin
This Android 4.2 Car Stereo Use Manual can help you know how to set the android 4.2 car stereo audio wifi, bluetooth, GPS, lanague, steering wheel, factory, button, date and time, safety, backup and reset. All android 4.2 car head units from autopumpkin.com are suitable. The detail instructions of Pumpkin android 4.2 car stereo wiring diagram.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdfufskemdikdok
This document provides an introduction and overview for the service manual of Suzuki Outboard motors DF9.9/15. It contains 3 sections - an introduction describing the purpose and scope of the manual, general safety precautions for working on outboard motors, and definitions of symbols used throughout the manual. The introduction states that the manual contains procedures for inspection, service and overhaul of the main components of the DF9.9/15 motors to help technicians provide quick and optimal service to customers. It also notes specific years and models that the manual covers and limitations.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdfujfksem8dudj
This document provides an introduction and overview for a service manual on Suzuki Outboard motors DF9.9/15. It contains 3 sections - an introductory foreword, general precautions for working on outboard motors, and a table of contents for the manual. The foreword introduces the manual and its purpose for providing technicians with procedures for inspection, service and overhaul of components. The general precautions section highlights important safety warnings. The table of contents provides an overview of the sections contained in the manual.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdffujsekdmidj3e
This document provides an introduction and overview of service information for Suzuki DF9.9/15 outboard motors. It contains sections on general information, periodic maintenance, ignition/electrical systems, fuel systems, and other components. The document instructs technicians to read all sections to familiarize themselves with the motor and proper service procedures before working on it. Safety precautions are also outlined.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdf8fusjkkmdd3e
This document provides an overview manual for the SUZUKI Outboard motor DF9.9/15. It contains sections on general information, periodic maintenance, ignition and electrical systems, fuel system, recoil starter, power unit, mid unit, lower unit, and routing diagrams. The manual aims to help technicians service the outboard motor by providing inspection and repair procedures, specifications, tightening torques, special tools, and required materials. It notes that illustrations show basic principles and work procedures but may not be exact representations.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdfqlz922356
This document provides an introduction and overview for a service manual on Suzuki DF9.9/15 outboard motors. It outlines general precautions for working on outboard motors safely. The manual is intended to help technicians properly inspect and service the motor by providing exploded views of components with instructions and specifications. Safety symbols used in the manual are defined.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdffujdkskemdmd
This document provides an overview manual for the SUZUKI Outboard motor DF9.9/15. It contains sections on general information, periodic maintenance, ignition and electrical systems, fuel system, recoil starter, power unit, mid unit, lower unit, and routing diagrams. The manual aims to help technicians service the outboard motor by providing inspection and repair procedures, specifications, tightening torques, and other technical details. Safety warnings are provided throughout and the document explains how to properly use the manual.
2003+ suzuki df9.9 df15 four stroke outboard motors service repair manualfjskekfmsmem
This document provides an introduction and overview of service information for Suzuki DF9.9/15 outboard motors. It contains sections on general information, periodic maintenance, ignition/electrical systems, fuel systems, and other components. The document instructs technicians to read all sections to familiarize themselves with the motor and proper service procedures before working on it. Safety precautions are also outlined.
The document provides information on turn signal and hazard warning systems. It describes the main components, which include a combination flasher, multi-function switch, turn signal indicator lamps, and turn signal lamps. It outlines procedures for diagnosing issues and testing components like the flasher and switch. Removal and installation instructions are provided for the multi-function switch and combination flasher.
This document provides information about steering systems for ZJ vehicles. It describes the major components of the power steering system including the recirculating ball steering gear, steering linkage, power steering pump, and steering column. It provides details on identifying codes for the steering gear and pump as well as diagnosing common noise complaints.
The document provides information about rear suspension and axles for a Grand Cherokee vehicle. It describes the main components of the rear suspension system, including coil springs, upper and lower suspension arms, shock absorbers, stabilizer bar, track bar, and jounce bumpers. It also explains how the standard differential allows the axle shafts to rotate at different speeds when turning corners to compensate for the longer path of the outside wheel. The Model 35 axle used in the Grand Cherokee can be equipped with an optional Trac-Lok limited slip differential.
This document provides an overview of fuel delivery systems for vehicles with 4.0L and 5.2L engines. It describes the components of the fuel pump module, which is mounted in the fuel tank and contains the electric fuel pump, fuel pressure regulator, and in-tank fuel filter. The fuel pressure regulator is no longer mounted on the fuel rail. Procedures are provided for releasing fuel system pressure before servicing, and for testing fuel system pressure.
This document appears to be an electronic service manual for the 1995 Jeep Grand Cherokee. The logo on the page links to instructions when clicked. The page requests the user click the link for further information.
This document provides information about power mirrors and an automatic day/night rear view mirror on Jeep Grand Cherokee models. It describes the major components of these systems and their functions. The document also provides diagnostic procedures to test the power mirror switch and motors, as well as the automatic rear view mirror. Finally, it lists the service procedures for removing and installing the power mirror switch and removing the power mirrors and automatic rear view mirror.
Kawasaki 90 z7b wheel loader service repair manual (serial no. 90c6 5001 and up)jfjkskefsmemwe
This document provides guidance on disassembling, assembling, tightening, painting, bleeding air, and preparing a wheel loader for maintenance work. It outlines precautions and procedures for these tasks, including cleaning parts, applying markings, using proper tools, lubricating surfaces, and avoiding contamination. Specified tightening torques and painting colors are also included. The overall document provides technical instructions for servicing and maintaining this particular wheel loader model.
2007 johnson evinrude outboard 9.9 hp service repair manualfjskeksmemedc
This document provides information on safety warnings and trademarks related to outboard engine repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that may be referenced in repair manuals.
2007 johnson evinrude outboard 9.9 hp service repair manualfujdjfjjskekmm
This document provides safety information and instructions for working on Evinrude/Johnson outboard motors. It lists numerous registered trademarks and outlines responsibilities of the manufacturer, dealer, and owner to ensure compliance with EPA emissions regulations. The document also explains various symbols and abbreviations used in the service manual.
2007 johnson evinrude outboard 9.9 hp service repair manualfujsjefjkskekfm
This document provides safety information and instructions for working on Evinrude/Johnson outboard motors. It lists registered trademarks and outlines responsibilities of the manufacturer, dealer, and owner to ensure engine emissions compliance. Symbols used in the manual are defined, including those for electrical components and values. Abbreviations are also listed to clarify terms used.
2007 johnson evinrude outboard 15 hp service repair manualfjkekfmefmm
This document provides information on safety warnings and trademarks related to outboard engine repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that may be referenced in repair manuals.
2007 Johnson Evinrude Outboard 15Hp Service Repair Manualujfjjsjefksekm
This document provides safety information and instructions for working on Evinrude/Johnson outboard motors. It discusses hazards from rotating propellers, exhaust fumes, electrical shock, and fuel. The document emphasizes taking safety precautions like disconnecting batteries, securing the outboard, and working in a ventilated area. It also notes the importance of using authorized replacement parts and following torque specifications.
2007 johnson evinrude outboard 15 hp service repair manualfjsjjfkskeme
This document provides information on safety warnings and trademarks related to outboard engine service and repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that are mentioned in the technical documentation.
2007 johnson evinrude outboard 9.9 hp service repair manualufjjskekmem
This document provides information on safety warnings and trademarks related to outboard engine repair. It lists numerous safety warnings regarding working with engines, fuel systems, electrical components, and rotating parts. It also lists many registered trademarks owned by various companies that produce components used in outboard engines.
Android 4.2 Car Stereo Instructions Use ManualAuto pumkin
This Android 4.2 Car Stereo Use Manual can help you know how to set the android 4.2 car stereo audio wifi, bluetooth, GPS, lanague, steering wheel, factory, button, date and time, safety, backup and reset. All android 4.2 car head units from autopumpkin.com are suitable. The detail instructions of Pumpkin android 4.2 car stereo wiring diagram.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdfufskemdikdok
This document provides an introduction and overview for the service manual of Suzuki Outboard motors DF9.9/15. It contains 3 sections - an introduction describing the purpose and scope of the manual, general safety precautions for working on outboard motors, and definitions of symbols used throughout the manual. The introduction states that the manual contains procedures for inspection, service and overhaul of the main components of the DF9.9/15 motors to help technicians provide quick and optimal service to customers. It also notes specific years and models that the manual covers and limitations.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdfujfksem8dudj
This document provides an introduction and overview for a service manual on Suzuki Outboard motors DF9.9/15. It contains 3 sections - an introductory foreword, general precautions for working on outboard motors, and a table of contents for the manual. The foreword introduces the manual and its purpose for providing technicians with procedures for inspection, service and overhaul of components. The general precautions section highlights important safety warnings. The table of contents provides an overview of the sections contained in the manual.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdffujsekdmidj3e
This document provides an introduction and overview of service information for Suzuki DF9.9/15 outboard motors. It contains sections on general information, periodic maintenance, ignition/electrical systems, fuel systems, and other components. The document instructs technicians to read all sections to familiarize themselves with the motor and proper service procedures before working on it. Safety precautions are also outlined.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdf8fusjkkmdd3e
This document provides an overview manual for the SUZUKI Outboard motor DF9.9/15. It contains sections on general information, periodic maintenance, ignition and electrical systems, fuel system, recoil starter, power unit, mid unit, lower unit, and routing diagrams. The manual aims to help technicians service the outboard motor by providing inspection and repair procedures, specifications, tightening torques, special tools, and required materials. It notes that illustrations show basic principles and work procedures but may not be exact representations.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdfqlz922356
This document provides an introduction and overview for a service manual on Suzuki DF9.9/15 outboard motors. It outlines general precautions for working on outboard motors safely. The manual is intended to help technicians properly inspect and service the motor by providing exploded views of components with instructions and specifications. Safety symbols used in the manual are defined.
2003+ Suzuki DF9.9 DF15 four stroke outboard motors Service Repair Manual.pdffujdkskemdmd
This document provides an overview manual for the SUZUKI Outboard motor DF9.9/15. It contains sections on general information, periodic maintenance, ignition and electrical systems, fuel system, recoil starter, power unit, mid unit, lower unit, and routing diagrams. The manual aims to help technicians service the outboard motor by providing inspection and repair procedures, specifications, tightening torques, and other technical details. Safety warnings are provided throughout and the document explains how to properly use the manual.
2003+ suzuki df9.9 df15 four stroke outboard motors service repair manualfjskekfmsmem
This document provides an introduction and overview of service information for Suzuki DF9.9/15 outboard motors. It contains sections on general information, periodic maintenance, ignition/electrical systems, fuel systems, and other components. The document instructs technicians to read all sections to familiarize themselves with the motor and proper service procedures before working on it. Safety precautions are also outlined.
The document provides information on turn signal and hazard warning systems. It describes the main components, which include a combination flasher, multi-function switch, turn signal indicator lamps, and turn signal lamps. It outlines procedures for diagnosing issues and testing components like the flasher and switch. Removal and installation instructions are provided for the multi-function switch and combination flasher.
This document provides information about steering systems for ZJ vehicles. It describes the major components of the power steering system including the recirculating ball steering gear, steering linkage, power steering pump, and steering column. It provides details on identifying codes for the steering gear and pump as well as diagnosing common noise complaints.
The document provides information about rear suspension and axles for a Grand Cherokee vehicle. It describes the main components of the rear suspension system, including coil springs, upper and lower suspension arms, shock absorbers, stabilizer bar, track bar, and jounce bumpers. It also explains how the standard differential allows the axle shafts to rotate at different speeds when turning corners to compensate for the longer path of the outside wheel. The Model 35 axle used in the Grand Cherokee can be equipped with an optional Trac-Lok limited slip differential.
This document provides an overview of fuel delivery systems for vehicles with 4.0L and 5.2L engines. It describes the components of the fuel pump module, which is mounted in the fuel tank and contains the electric fuel pump, fuel pressure regulator, and in-tank fuel filter. The fuel pressure regulator is no longer mounted on the fuel rail. Procedures are provided for releasing fuel system pressure before servicing, and for testing fuel system pressure.
This document appears to be an electronic service manual for the 1995 Jeep Grand Cherokee. The logo on the page links to instructions when clicked. The page requests the user click the link for further information.
This document provides information about power mirrors and an automatic day/night rear view mirror on Jeep Grand Cherokee models. It describes the major components of these systems and their functions. The document also provides diagnostic procedures to test the power mirror switch and motors, as well as the automatic rear view mirror. Finally, it lists the service procedures for removing and installing the power mirror switch and removing the power mirrors and automatic rear view mirror.
The document discusses various exterior body components of a vehicle. It provides removal and installation instructions for components like the grille, headlamps, hood, hood latches and related parts. The document is organized in sections covering the grille/reinforcement, radiator support, hood, hood hinges/latches/striker and other exterior parts. Diagrams and step-by-step instructions are provided for servicing these exterior body parts.
This document provides information about power seats in Jeep Grand Cherokee models. It describes the major components of the power seat system, including the power seat switch and three reversible motors that operate the seat adjustments. The document provides guidance on diagnosing issues with the power seat motors or switch, including continuity tests of the switch connections. It also outlines procedures for removing and installing the power seat switch and motor/adjuster assembly.
This document provides information about a vehicle theft alarm system, including:
- General descriptions of how the system arms, disarms, and responds to unauthorized access attempts.
- Instructions for performing self-diagnosis tests to check the operation of sensors and circuits.
- Procedures for technicians to remove and install the VTA module, which involves removing various dash panel components.
- Steps for technicians to diagnose the system using the self-diagnosis mode and by checking for proper horn responses from sensors.
This document contains information about brakes for a vehicle model. It includes sections on general brake information, ABS brakes, changes for the 1995 model year, brake components, fluids and cleaning products, safety precautions, and an index of topics. The key points are:
- The vehicle uses power assisted four-wheel disc brakes with ABS standard on all models.
- Changes for 1995 include different master cylinder, power brake booster, and hydraulic control unit components for the ABS system.
- Safety precautions for working on brakes include wearing protective equipment and properly disposing of any potential asbestos dust.
This document provides information about exhaust systems and intake manifolds. It discusses the basic components of exhaust systems, including exhaust manifolds, pipes, catalytic converters, heat shields, mufflers and tailpipes. It describes symptoms of exhaust system problems and provides procedures for removing and installing exhaust pipes and manifolds. Intake manifolds and catalytic converters are also discussed.
The document provides general information about emission control systems, including:
1) It describes the different emission control components and systems used on 4.0L and 5.2L engines.
2) It explains how the on-board diagnostic system checks for faults in emission components like the EGR and EVAP systems.
3) It provides an overview of the evaporative emission control system and its components like the EVAP canister.
The document provides information about the overhead console in Jeep Grand Cherokee models. It describes the different types of overhead consoles that are used depending on whether the vehicle has a power sunroof option. It also describes the major components in the overhead console including the trip computer, compass, thermometer, reading lamps, remote garage door opener storage, and sunglasses storage. The document provides details on diagnosing issues with these components through self-diagnostic tests and flow charts.
This document provides general information about audio systems for Jeep Grand Cherokee models. It describes components such as radios, speakers, antennas, and amplifiers. It also provides diagnostic procedures and service instructions for removing and installing these components.
This document provides information about cooling system diagnosis and service procedures for a vehicle. It includes:
- An overview of cooling system components and coolant routing
- Diagnosis charts to help identify potential causes of overheating
- Procedures for testing the water pump, draining and refilling the cooling system, and replacing components like the radiator, hoses, thermostat, and water pump.
- Cautions for working on the high-pressure cooling system and ensuring the correct rotating water pump is installed.
This document provides contact information for obtaining special service tools in the United States, Canada, and internationally. The same tools or their equivalent are required for certain vehicle service operations and can be obtained from local sources or through the listed contacts, which include addresses and phone/fax numbers for Miller Special Tools in Michigan and C&D Riley Enterprises in Ontario.
The document provides information about manual transmissions and transfer cases used in Jeep vehicles, including:
- An index listing transmission and transfer case models covered
- Service information for the AX15 5-speed manual transmission, including identification, gear ratios, lubrication, diagnosis and repair procedures
- Procedures for transmission removal, disassembly, component inspection and installation
The document provides information about diagnosing issues with a vehicle's rear window defogger system. It describes the major components of the system, including the rear window glass grid, defogger switch, and defogger relay/timer. It then lists steps to test overall system operation and to isolate problems, such as using a voltmeter to check for breaks in the glass grid lines or testing power supply to the relay.
This document provides information on propeller shafts. It discusses:
1) There are three types of propeller shafts used on 4WD vehicles, differing by their joint configurations and whether they include a slip yoke.
2) Universal joints are used to allow the propeller shaft to operate at different angles and are not repairable if damaged.
3) Vibration can be caused by an unbalanced propeller shaft, worn or misaligned universal joints, or other vehicle component issues like loose engine mounts. Diagnosis procedures include measuring runout and clamping sections to isolate the source.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
1. XJ BODY 23 - 1
BODY
CONTENTS
page page
BODY COMPONENT SERVICE . . . . . . . . . . . . . 16 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
GENERAL SERVICE INFORMATION . . . . . . . . . . 1 STATIONARY GLASS . . . . . . . . . . . . . . . . . . . . . 4
PAINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
GENERAL SERVICE INFORMATION
GENERAL INFORMATION Do not use harsh alkaline based cleaning sol-
vents on painted or upholstered surfaces. Damage
SAFETY PRECAUTIONS AND WARNINGS to finish or color can result.
Do not hammer or pound on plastic trim panel
WARNING: EYE PROTECTION SHOULD BE USED when servicing interior trim. Plastic panels can
WHEN SERVICING GLASS COMPONENTS. PER- break.
SONAL INJURY CAN RESULT.
USE A OSHA APPROVED BREATHING FILTER Chrysler Corporation uses many different types of
WHEN SPRAYING PAINT OR SOLVENTS IN A CON- push-in fasteners to secure the interior and exterior
FINED AREA. PERSONAL INJURY CAN RESULT. trim to the body. Most of these fasteners can be
AVOID PROLONGED SKIN CONTACT WITH reused to assemble the trim during various repair
PETROLEUM OR ALCOHOL– BASED CLEANING procedures. At times, a push-in fastener cannot be
SOLVENTS. PERSONAL INJURY CAN RESULT. removed without damaging the fastener or the com-
DO NOT STAND UNDER A HOISTED VEHICLE ponent it is holding. If it is not possible to remove a
THAT IS NOT PROPERLY SUPPORTED ON SAFETY fastener without damaging a component or body, cut
STANDS. PERSONAL INJURY CAN RESULT. or break the fastener and use a new one when
installing the component. Never pry or pound on a
plastic or pressed-board trim component. Using a
CAUTION: When holes must be drilled or punched suitable fork-type prying device, pry the fastener
in an inner body panel, verify depth of space to the from the retaining hole behind the component being
outer body panel, electrical wiring, or other compo- removed. When installing, verify fastener alignment
nents. Damage to vehicle can result. with the retaining hole by hand. Push directly on or
Do not weld exterior panels unless combustible over the fastener until it seats. Apply a low-force pull
material on the interior of vehicle is removed from to the panel to verify that it is secure.
the repair area. Fire or hazardous conditions, can When it is necessary to remove components to ser-
result. vice another, it should not be necessary to apply
Always have a fire extinguisher ready for use excessive force or bend a component to remove it.
when welding. Before damaging a trim component, verify hidden
Disconnect the negative (-) cable clamp from the fasteners or captured edges holding the component in
battery when servicing electrical components that place.
are live when the ignition is OFF. Damage to electri-
cal system can result.
Do not use abrasive chemicals or compounds on
painted surfaces. Damage to finish can result.
2. 23 - 2 BODY XJ
PAINT
INDEX
page page
GENERAL INFORMATION WET SANDING, BUFFING, AND POLISHING . . . 2
BASE COAT/CLEAR COAT FINISH . . . . . . . . . . . 2 SPECIFICATIONS
PAINT CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AFTERMARKET PAINT REPAIR PRODUCTS . . . 3
PAINTED SURFACE TOUCH-UP . . . . . . . . . . . . 2
GENERAL INFORMATION PAINTED SURFACE TOUCH-UP
When a painted metal surface has been scratched
PAINT CODE or chipped, it should be touched-up as soon as possi-
Exterior vehicle body colors are identified on the ble to avoid corrosion. For best results, use Mopar
Body Code plate. The plate is located on the left side Scratch Filler/Primer, Touch-Up Paints and Clear Top
of the dash panel in the engine compartment. Refer Coat. Refer to Introduction group of this manual for
to the Introduction section at the front of this man- Body Code Plate information.
ual for body code plate description. The paint code is
also identified on the Vehicle Safety Certification TOUCH-UP PROCEDURE
Label which is located on the drivers door shut face. (1) Scrape loose paint and corrosion from inside
The color names provided in the Paint and Trim scratch or chip.
Code Description chart are the color names used on (2) Clean affected area with Mopar Tar/Road Oil
most repair product containers. Remover, and allow to dry.
(3) Fill the inside of the scratch or chip with a coat
BASE COAT/CLEAR COAT FINISH of filler/primer. Do not overlap primer onto good sur-
On most vehicles a two-part paint application (base face finish. The applicator brush should be wet
coat/clear coat) is used. Color paint that is applied to enough to puddle-fill the defect without running. Do
primer is called base coat. The clear coat protects the not stroke brush applicator on body surface. Allow
base coat from ultraviolet light and provides a dura- the filler/primer to dry hard.
ble high-gloss finish. (4) Cover the filler/primer with color touch-up
paint. Do not overlap touch-up color onto the original
WET SANDING, BUFFING, AND POLISHING color coat around the scratch or chip. Butt the new
Minor acid etching, orange peel, or smudging in color to the original color, if possible. Do not stroke
clear coat or single-stage finishes can be reduced applicator brush on body surface. Allow touch-up
with light wet sanding, hand buffing, and polishing. paint to dry hard.
If the finish has been wet sanded in the past, it (5) On vehicles without clear coat, the touch-up
cannot be repeated. Wet sanding operation color can be lightly wet sanded (1500 grit) and pol-
should be performed by a trained automotive ished with rubbing compound.
paint technician. (6) On vehicles with clear coat, apply clear top coat
to touch-up paint with the same technique as
CAUTION: Do not remove clear coat finish, if described in Step 4. Allow clear top coat to dry hard.
equipped. Base coat paint must retain clear coat for If desired, Step 5 can be performed on clear top coat.
durability.
3. XJ BODY 23 - 3
SPECIFICATIONS
AFTERMARKET PAINT REPAIR PRODUCTS
EXTERIOR COLOR
CHRY S-W ACME AKZO/NOBEL
EXTERIOR COLOR PPG BASF DuPONT
CODE * M-S SIKKENS
Flame Red PR4 4679 23043 B9326 46916 CHA93:PR4
Clear Coat
Magenta Clear Coat SH1 74171 26079 B9615 51522 CHA96:SH1
Citron Pearl Coat SJV 47694 26081 B9672 51524 CHA96:SJV
Moss Green RJN 47383 25036 B9533 50277 CHA95:RJN
Pearl Coat
Bright Jade SQP 47586 26088 B9636 51533 CHA96:SQP
Satin Glow
Lapis Blue RC4 4935 24098 B9531 50218 CHA95:RC4
Clear Coat
Dark Blue PCJ 4783 24072 B9453 48543 CHA94:PCJ
Pearl Coat
Black Clear Coat DX8 9700 15214 99 34858 CHA85:DX8
Gunmetal Pearl Coat TQ7 5248 27035 B9735 52952 CHA97:TQ7
Stone White SW1 83542 26089 B9622 51539 CHA96:SW1
Clear Coat
CLADDING COLOR
CLADDING CHRY S-W ACME AKZO/NOBEL
PPG BASF DuPONT
COLOR CODE * M-S SIKKENS
Flame Red PR4 4679 23043 B9326 46916 CHA93:PR4
Moss Green RJN 47383 25036 B9533 50277 CHA95:RJN
Dark Blue PCJ 4783 24072 B9453 48543 CHA94:PCJ
Pear Coat
Gunmetal TQ7 5248 27035 B9735 52952 CHA:TQ7
Pearl Coat
Black DX8 9700 15214 F0204 34858 CHA85:DX8
Stone White SW1 83542 26089 B9622 51539 CHA96:SW1
*Herberts Standox and Spies Hecker use the Chrysler paint code as listed on the Body Code Plate and the
Vehicle Safety Certification label.
INTERIOR COLOR
INTERIOR S-W ACME
CHRY CODE PPG BASF DuPONT
COLOR M-S
Mist Gray C3 35799/2-1576 25065 C9507 50508
Saddle T6 27917/2-1594 26121 C9604 51542
4. 23 - 4 BODY XJ
STATIONARY GLASS
INDEX
page page
DESCRIPTION AND OPERATION REAR DOOR STATIONARY WINDOW GLASS . . 7
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . 4 REAR QUARTER WINDOW GLASS . . . . . . . . . . 8
REMOVAL AND INSTALLATION WINDSHIELD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LIFTGATE GLASS . . . . . . . . . . . . . . . . . . . . . . . 8
DESCRIPTION AND OPERATION structural support for the roof. The urethane bonding
used to secure the windshield to the fence is difficult
SAFETY PRECAUTIONS to cut or clean from any surface. The moldings are
set in urethane, and will be damaged during the
WARNING: DO NOT OPERATE THE VEHICLE removal process. Before removing the windshield,
WITHIN 24 HOURS OF WINDSHIELD INSTALLATION. check the availability of the windshield and moldings
IT TAKES AT LEAST 24 HOURS FOR URETHANE from the parts supplier.
ADHESIVE TO CURE. IF IT IS NOT CURED, THE
WINDSHIELD MAY NOT PERFORM PROPERLY IN
AN ACCIDENT. REMOVAL AND INSTALLATION
URETHANE ADHESIVES ARE APPLIED AS A SYS-
TEM. USE GLASS CLEANER, GLASS PREP SOL- WINDSHIELD
VENT, GLASS PRIMER, PVC (VINYL) PRIMER AND The windshield is positioned in the reveal molding
PINCHWELD (FENCE) PRIMER PROVIDED BY THE and is bonded to the windshield frame with urethane
ADHESIVE MANUFACTURER. IF NOT, STRUCTURAL adhesive.
INTEGRITY COULD BE COMPROMISED. Depending on the circumstances, either one of two
USE ONLY ADHESIVES, PRIMERS AND CLEAN- windshield glass installation methods can be used:
ERS THAT MEET OR EXCEED THE FMVSS 212 • The short method.
WINDSHIELD RETENTION STANDARD AND THE • The extended method.
FMVSS 216 ROOF CRUSH STANDARD. The short method is used when the windshield
BE SURE TO REFER TO THE URETHANE MANU- glass is removed intact, and the body opening and
FACTURER’S DIRECTIONS FOR CURING TIME the pinchweld flanges do not require repair.
SPECIFICATIONS, AND DO NOT USE ADHESIVE The extended method must be used when the body
AFTER ITS EXPIRATION DATE. opening or a flange is damaged. The extended
VAPORS THAT ARE EMITTED FROM THE URE- method must also be used when urethane no longer
THANE ADHESIVE OR PRIMER COULD CAUSE adheres to either the windshield glass or the pinch-
PERSONAL INJURY. USE THEM IN A WELL-VENTI- weld flanges.
LATED AREA.
REMOVAL
SKIN CONTACT WITH URETHANE ADHESIVE
(1) Cover the interior and exterior body surface
SHOULD BE AVOIDED. PERSONAL INJURY MAY
areas with a protective covering.
RESULT.
(2) Remove the windshield wiper arms and the
ALWAYS WEAR EYE AND HAND PROTECTION
rearview mirror.
WHEN WORKING WITH GLASS.
(3) Using a razor knife, slide the blade between
the windshield glass and the inboard edge of the
CAUTION: Protect all painted and trimmed surfaces reveal molding.
from coming in contact with urethane or primers. (4) Cut around the interior perimeter of the reveal
Be careful not to damage painted surfaces when molding and sever the cap of the reveal molding.
removing moldings or cutting urethane around (5) Using a cold knife, cut the urethane around the
windshield. perimeter of the windshield (Fig. 1).
(6) Remove the windshield glass from the frame.
It is difficult to salvage a windshield during the
removal operation. The windshield is part of the
5. COLD KNIFE WINDSHIELD
XJ BODY 23 - 5
REMOVAL AND INSTALLATION (Continued)
by 50 cm (4 in. by 4 in. by 20 in.) blocks, placed par-
allel 75 cm (2.5 ft.) apart (Fig. 2).
CAUTION: Avoid spilling or dripping primer on
painted surfaces. Clean spills or drips immediately.
The primer will damage the paint if it remains on
the surface for any length of time.
(10) If the replacement windshield glass does not
have blackout primer:
• Attach a 25 mm (1 in) wide masking tape band
around the interior side of the glass 16 mm (5/8 in)
from the edge of the glass (Fig. 3).
• Do not attach tape along the bottom of the glass
and attach it only to the inside of the glass.
• Clean the 16-mm (5/8-in) wide surface area
around the glass with isopropyl alcohol.
Fig. 1 Cutting Urethane Around Windshield—Typical • Thoroughly mix and apply glass blackout primer
INSTALLATION—SHORT METHOD to the 16 mm (5/8 in) surface area around the inte-
(1) Trim the urethane from the pinchweld flanges. rior side of the glass (Fig. 4).
Leave a 3 mm (0.1 in.) level base of urethane on the • Allow the primer to dry for at least 10-12 min-
pinchweld flanges. utes.
(11) Apply a small amount of adhesive to the bot-
WARNING: DO NOT USE SOLVENT BASED GLASS tom support spacers and attach the support spacers
CLEANER TO CLEAN WINDSHIELD BEFORE to the bottom of the windshield, 170 mm inboard
APPLYING GLASS PREP AND PRIMER. POOR from the outer windshield edge (Fig. 5).
ADHESION CAN RESULT. (12) Cut the urethane adhesive applicator nozzle
(Fig. 6).
(2) Clean inside of windshield with ammonia based
glass cleaner and lint-free cloth. CAUTION: Be prepared to install the glass immedi-
(3) Prime outer perimeter of interior side of glass ately after applying the adhesive, as the adhesive
16 mm (5/8 inch) from edge. Use a wipe-off type ure- will begin to cure in less than 10 minutes.
thane primer and wipe glass dry after primer appli-
cation. (13) Apply a continuous, 6-mm (1/4-in) diameter
bead of urethane adhesive to the surface area.
NOTE: The reveal molding has an adhesive applied (14) Align the glass with the reference marks and
to the windshield contact surface to help secure the position the glass on the pinchweld flanges. Ensure
molding to the windshield during the installation that the windshield glass is correctly seated on the
procedure. support spacers.
(15) Force the windshield glass inward just enough
(4) Apply the molding to the windshield: to wet-out and set the urethane. Use care to avoid
• With the molding at room temperature, press excessive squeeze-out of adhesive.
the molding onto the windshield corners. (16) Water test the windshield with a water spray
• From corner to corner, work the molding to the after installation. Do not direct high pressure
center of each side. (Some stretching of the molding streams of water directly at urethane. If any leaks
may be required during this procedure.) are detected, apply urethane as necessary.
(5) Place the glass on the pinchweld flanges and (17) If used, remove the masking tape from the
inspect for gaps in the urethane. Gaps in excess of 3 inner surface of the glass.
mm (1/8 inch) must be filled with urethane. (18) Install all components and clean the vehicle.
(6) Adjust windshield glass position until it is (19) Open the vehicle windows to prevent interior
aligned with the flanges and adhesive. pressure while the urethane is curing. If not
(7) Using a grease pencil or equivalent, make vented, pressure in the interior of the vehicle
alignment marks on the glass and body. may interfere with proper glass bonding.
(8) Remove replacement windshield from wind- (20) Install the rearview mirror.
shield opening.
(9) Position the windshield inside up on a suitable
work surface with two padded, wood 10 cm by 10 cm
6. WINDSHIELD TAPE
AND MOLD- MASKING OFOFINCH
POSITION PRIMER TO GLASS
INGS
APPLY EDGE WIDE BLACKOUT PRIMER CATOR
FROM TAPE TAPE
1-INCH AREA GLASS
5/8 THIS BLOCKS APPLI- COWL SUPPORT
MOLDING SPACER CUTSUPPORTSHAPE SHAPE
FOR EXTENDED PROCE-
CUT NOZZLE NOZZLE SPACERS
FORWINDSHIELD
THIS DURE
SHORT THIS
PROCEDURE
23 - 6 BODY XJ
REMOVAL AND INSTALLATION (Continued)
Fig. 2 Work Surface Set up
Fig. 5 Windshield Bottom Support Spacers
Fig. 3 Masking Tape Location For Blackout Primer
Fig. 6 Applicator Nozzle Preparation
INSTALLATION—EXTENDED METHOD
(1) Remove the all of urethane from all pinchweld
flanges.
(2) Inspect and repair the windshield opening and
pinchweld flanges.
(3) Prime the pinchweld flanges with a urethane
base primer. However, if the flange is color-coated
with paint, prime the flanges with a paint finish
primer. This is important because urethane
adhesive will not adhere to all color-coat
paints. Allow primer sufficient time to dry.
NOTE: The reveal molding has an adhesive applied
to the windshield contact surface to help secure the
molding to the windshield during the installation
procedure.
Fig. 4 Blackout Primer Application
(4) Apply the reveal molding to the windshield:
7. DIVISION BAR
UPPER SCREW GLASS SCREW
LOWER
XJ BODY 23 - 7
REMOVAL AND INSTALLATION (Continued)
• With the molding at room temperature, press (14) Water test the windshield with a water spray
the molding onto the windshield corners. after installation. Do not direct high pressure
• From corner to corner, work the molding to the streams of water directly at the urethane. If any
center of each side. (Some stretching of the molding leaks are detected, apply urethane as necessary.
may be required during this procedure). (15) If used, remove the masking tape from the
(5) Install and inspect the fit of the windshield on inner surface of glass.
the pinchweld flanges as follows: (16) Install all components and clean the vehicle.
• Position windshield until it is aligned within If necessary, refer to the installation procedures.
windshield opening. (17) Open the vehicle windows to prevent interior
• Measure the gap between the pinchweld flanges pressure while the urethane adhesive is curing. If
and glass around perimeter of the glass and flange. not vented, pressure in the interior of vehicle
• The reveal molding should equally cover the will interfere with glass bonding.
A-Pillars on both sides. (18) Install the rearview mirror on the bracket.
• The flanges should also extend above the glass
edge equally around the perimeter of the opening. REAR DOOR STATIONARY WINDOW GLASS
(6) If the pinchweld flanges require repair, remove
the windshield glass and straighten, align, or repair REMOVAL
the flange(s) as necessary. The rear door stationary window glass is bonded to
(7) Position the windshield in the opening and the division bar and is serviced as an assembly.
inspect the windshield fit again. Mark the windshield (1) Lower the window glass.
final position on the glass and body with a wax pen- (2) Remove the inner and outer beltline weather-
cil (or use masking tape). The marks (or masking strip.
tape) will be used for installation alignment refer- (3) Remove the trim panel and waterdam from
ence. door inner panel.
(8) If the replacement windshield does not have (4) Remove the screws attaching the division bar/
blackout primer: glass to the door (Fig. 7).
• Attach a 25-mm (1-in) wide masking tape band (5) Tilt the division bar/glass forward and remove
around the interior side of glass 16 mm (5/8 in) from it from the door.
edge of glass (Fig. 3).
• Do not attach tape along the bottom of the glass
and attach only to the inside of glass.
• Thoroughly mix and apply blackout primer to
the 16 mm (5/8 in) surface area around the interior
side of the glass (Fig. 4).
• Allow the primer to dry for at least 10-12 min-
utes.
(9) Apply a small amount of adhesive to the bot-
tom support spacers and attach the support spacers
to the bottom of the windshield, 170 mm inboard
from the outer windshield edge (Fig. 5).
(10) Cut the urethane applicator nozzle (Fig. 6).
(11) Apply a continuous bead of urethane to the
surface area with blackout primer on the interior
side of glass. The bead should be 9-mm (3/8-in) wide
by 12.7-mm (1/2-in) deep for best results. Fig. 7 Division Bar/Stationary Glass
CAUTION: Be prepared to install the glass immedi- INSTALLATION
ately after applying the adhesive, as the adhesive (1) Position the division bar/glass in the door.
will begin to cure in less than 10 minutes. (2) Install the screws attaching the division bar/
glass to the door. Finger tighten the screws.
(12) Align the windshield with the wax pencil (3) Tighten the upper screw to 6 N·m (5 ft-lbs)
installation alignment reference marks (or the tape torque.
strips). Position the windshield on pinchweld flanges (4) Tighten the lower screw to 6 N·m (5 ft-lbs)
and spacers. torque.
(13) Force the windshield inward just enough to (5) Install the beltline weatherstrip.
wet-out and set the urethane. Use care to avoid (6) Install the door waterdam and trim panel.
excessive squeeze-out of adhesive.
8. WEATHERSTRIP
SEAL REVEAL MOUL-
DING FRT GLASS QUARTER CORD
INSTALLATION GLASS
WINDOW INSTALLATION CORD
WINDOW
W/VENTWEATHERSTRIP INSTALLATIONENDWEATHERSTRIP SEAL
SEAL CORD WINDOW SEAL
WEATHER-
STRIP
GLASS
23 - 8 BODY XJ
REMOVAL AND INSTALLATION (Continued)
REAR QUARTER WINDOW GLASS (7) Pull on each end of the cord to pull the weath-
erstrip seal channel lip over the window opening
REMOVAL flanges.
(1) If equipped, remove the quarter window reveal (8) Test the vent window for water leaks.
molding (Fig. 8). (9) Install the interior trim cover.
(2) Remove the quarter window interior trim cov- (10) If equipped, install the quarter window reveal
ers. molding.
(3) Separate the weatherstrip seal lip from the
window opening flanges. Use a pry tool and carefully
push the window glass and seal outward.
(4) Remove the weatherstrip seal and window
glass from window opening.
(5) Remove the weatherstrip seal from the window
glass.
Fig. 9 Weatherstrip Seal and Cord Installation
Fig. 8 Quarter Window Reveal Molding, Glass and
Seal
INSTALLATION
(1) Clean the original sealant from the weather-
strip channels and window opening flanges.
(2) Apply a 4-mm (1/6-in) diameter bead of sealant
to the window channel in the weatherstrip seal.
(3) Install the weatherstrip on the window glass.
Install the seal installation cord in the window open-
ing flange channel (Fig. 9) as follows: Fig. 10 Quarter Window With Vent
• Moisten a length of 6-mm (1/4-in) diameter cord
with a soap and water solution.
LIFTGATE GLASS
• Ensure that the cord is long enough to go all the REMOVAL
way around the perimeter of the weatherstrip. (1) Open liftgate.
• Insert the cord into the window opening flange (2) Remove liftgate trim panel.
channel in the weatherstrip seal. (3) Disconnect heated backlite (HBL) connector.
(4) Apply a 6-mm (1/4-in) diameter bead of sealant (4) Remove wiper arm.
to the window opening flanges. (5) Remove CHMSL lens.
(5) For two-door vehicles, apply a 3-mm (1/8-in) (6) Using a razor knife, slide the blade between
diameter bead of sealant at the quarter panel appli- the liftgate glass and the inboard edge of the reveal
que and liftgate pillar seam. molding.
(6) Position the quarter window glass and the (7) Cut around the interior perimeter of the reveal
weatherstrip seal in the window opening (Fig. 10) molding and severe the cap of the reveal molding.
with the free ends of the cord inside the vehicle (Fig.
11).
9. (POSITIONWEATHERSTRIP
1/4-INCH DIAMETER CORD
STRIP GLASS WEATHER-
IN CHANNEL)
XJ BODY 23 - 9
REMOVAL AND INSTALLATION (Continued)
(4) Verify the glass lays evenly against the fence at
the sides, top and bottom. If not, the flange must be
formed to the shape of the new glass.
(5) Using a grease pencil or equivalent, make ref-
erences marks on the glass and body.
(6) Remove replacement glass from liftgate open-
ing.
(7) Position the glass inside up on a suitable work
surface.
WARNING: DO NOT USE SOLVENT BASED GLASS
CLEANER TO CLEAN WINDSHIELD BEFORE
APPLYING GLASS PREP AND PRIMER. POOR
ADHESION CAN RESULT.
(8) Clean inside of glass with Mopar Glass Cleaner
and lint-free cloth.
(9) Apply PVC (vinyl) primer 25 mm (1 in.) wide
around edge of glass. Wipe with clean/dry lint-free
cloth.
(10) If necessary, apply fence primer around edge
of fence. Allow at least eighteen minutes drying time.
Fig. 11 Quarter Window Glass and Seal Installation (11) Apply a 10 mm (0.4 in.) bead of urethane
around glass border.
(8) Using a cold knife, cut urethane bonding from (12) Position glass into liftgate opening and refer-
around liftgate glass. A pneumatic cutting device can ence marks.
be used if available. (13) Push the glass inward until the reveal mold-
(9) Separate glass from Liftgate. ing is seated onto the liftgate frame. Use care to
avoid excessive squeeze-out of adhesive.
INSTALLATION
(14) Open windows to prevent pressure build-up
CAUTION: Open a window before installing glass. while the urethane is curing.
This will avoid pressurizing the passenger compart- (15) Apply 150 mm (6 in.) lengths of 50 mm (2 in.)
ment. If a door or liftgate is slammed before ure- masking tape spaced 250 mm (10 in.) apart to hold
thane is cured, water leaks can result. glass in place until urethane cures.
(16) Install the wiper arm.
(1) Trim the urethane from the liftgate glass open- (17) Install CHMSL lens.
ing flanges. Leave a 3 mm (0.1 in.) level base of ure- (18) Connect heated backlite (HBL) connector.
thane on the flanges. (19) After urethane has cured, remove tape strips
(2) Starting in the corners, press reveal molding and water test to verify repair.
onto glass. (20) Install liftgate trim panel.
(3) Place replacement glass into liftgate opening
and position glass in the center of the opening
against flange.
10. EXTRACTOR6773
EXTRACTOR
TOOL 6773
TOOL HEAD RESTRAINT
RESTRAINT
HEAD SLEEVE
SLEEVE SEAT BACK FWD
FWD BACK
SEAT
23 - 10 BODY XJ
SEATS
INDEX
page page
REMOVAL AND INSTALLATION HEAD RESTRAINT SLEEVE . . . . . . . . . . . . . . . 10
BUCKET SEAT CUSHION COVER . . . . . . . . . . 13 REAR SEAT CUSHION COVER . . . . . . . . . . . . 13
BUCKET SEAT PLATFORM . . . . . . . . . . . . . . . 12 REAR SEATBACK COVER . . . . . . . . . . . . . . . . 14
BUCKET SEAT RECLINER . . . . . . . . . . . . . . . . 13 REAR SEATBACK LATCH STRIKER AND
BUCKET SEAT TRACK . . . . . . . . . . . . . . . . . . . 11 BUMPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
BUCKET SEATBACK COVER . . . . . . . . . . . . . . 12 SPECIAL TOOLS
BUCKET SEATBACK . . . . . . . . . . . . . . . . . . . . 12 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HEAD RESTRAINT COVER . . . . . . . . . . . . . . . 10
REMOVAL AND INSTALLATION
HEAD RESTRAINT SLEEVE
REMOVAL
NOTE: When replacing a head restraint sleeve, the
retaining tabs on the sleeve will be damaged during
the removal process. Check the availability of
replacement parts before servicing.
(1) Raise head restraint to the full up position.
(2) Turn head restraint lock thumbwheel to release
head restraint and pull head restraint upward to
remove from seat back.
(3) Insert head restraint sleeve extractor (special
tool 6773) (Fig. 1) and (Fig. 2) into the seat back. Fig. 1 Head Restraint Sleeve Extractor
(4) The retaining tabs are positioned on each side
of the sleeve, when inserting the extractor, ensure
that the flat of the collar is facing the side of the
seatback (Fig. 3).
(5) Using a small hammer, tap extractor down-
ward to release sleeve retaining tab.
(6) Remove extractor tool from sleeve, rotate tool
180 degrees (Fig. 4) and repeat steps 3 and 4.
(7) Remove extractor tool from sleeve and remove
sleeve from seat back.
INSTALLATION
(1) Position the sleeve in the seat back.
(2) Firmly, push sleeve down to snap into place.
(3) Install head restraint.
HEAD RESTRAINT COVER
Fig. 2 Head Restraint Sleeve Extractor Installation
REMOVAL
(3) Pull the adjuster bar from the head restraint.
(1) Remove head restraint from the bucket seat.
(4) Roll the cover upward and separate from the
(2) Remove the screws attaching the bezel and
head restraint cushion (Fig. 6).
adjuster bar to the head restraint (Fig. 5).
11. EXTRACTOR
LOCK RELEASE
THUMBWHEEL
TOOL 6773 EXTRACTOR RELEASEBACK BACK
TOOL 6773 SEAT SEAT
LOCK
THUMBWHEEL FWD HEAD RESTRAINT CUSHION HEAD RESTRAINT COVER
HEAD RESTRAINT
ADJUSTER BAR
BEZEL
XJ BODY 23 - 11
REMOVAL AND INSTALLATION (Continued)
Fig. 3 Head Restraint Sleeve Extractor Positioning
Fig. 5 Head Restraint
Fig. 4 Head Restraint Sleeve Extractor Positioning
INSTALLATION
(1) Position the cover on the head restraint cush-
ion and roll the cover downward.
(2) Position the adjuster bar in the head restraint.
(3) Install the screws attaching the bezel and
adjuster bar to the head restraint. Fig. 6 Head Restraint Cover
(4) Install head restraint in the bucket seat. (4) Remove the nuts attaching the seat track to
the bucket seat platform.
BUCKET SEAT TRACK (5) When separating the seat track from the plat-
form, route the power seat switch connector through
REMOVAL the access hole in the seat cushion frame, if
equipped.
NOTE: If the vehicle is equipped with manually
adjusted bucket seats, the inboard or outboard seat INSTALLATION
track may be serviced separately. (1) While positioning the seat track on the bucket
seat platform, route the power seat switch connector
(1) Remove bucket seat from vehicle. through the access hole in the seat cushion frame, if
(2) Remove screws attaching the side shield trim equipped.
cover from the seat. (2) Install the nuts attaching the seat track to the
(3) If equipped, disengage the power seat connec- bucket seat platform.
tor from the power seat switch. (3) If equipped, engage the power seat connector to
the power seat switch.
12. SEAT BACK COVER
SEAT CUSHION
BACK SEAT BACKFAS-
LOOP
HOOK SEAT CUSH- CUSHION
SEAT TENER
COVER
BACK
AND
BACK
ION HOG RING SUPPORT
23 - 12 BODY XJ
REMOVAL AND INSTALLATION (Continued)
(4) Install screws attaching the side shield trim
cover to the seat.
(5) Install bucket seat.
BUCKET SEAT PLATFORM
Bucket seat platforms are not repairable. If the
seat platform is damaged, replace platform as a unit.
BUCKET SEATBACK COVER
REMOVAL
(1) Remove head restraint, if equipped.
(2) Remove screws attaching side shield trim cover
to bucket seat.
(3) If equipped, disengage power seat wire connec-
tor from power seat switch.
(4) Remove the inboard seatback pivot bolt. Fig. 8 Hog Ring
(5) Position the seatback in the full forward or full
recline position.
(6) Remove the seatback cover zipper from the
base of the seatback.
(7) Disengage the cover zipper and route the zip-
per end between the inboard seatback and seat cush-
ion frame.
(8) Roll the seatback cover upward (Fig. 7).
(9) Disengage the hogrings attaching the seatback
cover to the seatback cushion support wires (Fig. 8).
(10) Roll the seatback cover upward and disengage
the hook and loop fastener (Fig. 9).
(11) Roll seatback cover up and over the head
restraint sleeves, if equipped and separate from the
seatback.
Fig. 9 Hook And Loop Fastener
(3) Continue rolling the cover downward and
engage the hogrings attaching the seatback cover to
the seatback cushion support wires.
(4) Route the zipper end between the inboard seat-
back and seat cushion frame and engage the cover
zipper.
(5) Install the inboard seatback pivot bolt.
(6) Install the side shield trim cover.
(7) Install head restraint, if equipped.
BUCKET SEATBACK
REMOVAL
(1) Remove side shield trim cover.
Fig. 7 Seatback Cover (2) Remove inboard seatback pivot bolt.
INSTALLATION (3) Remove bolts attaching recliner to seat cushion
(1) Position the seatback cover on the seatback frame (Fig. 10).
cushion and roll seatback cover down over the head (4) Separate seatback from vehicle.
restraint sleeves. Route the sleeves through the
access holes in the cover, if equipped. INSTALLATION
(2) Roll the seatback cover downward and engage (1) Position seatback on seat cushion frame.
the hook and loop fastener. (2) Install inboard seatback pivot bolt.
13. SEAT BACK RING
RECLINEREAT CUSHION
SEAT CUSHION
COVER
S
HOG SEAT CUSHION RECLINER SEATCUSHION
REMOVE
BACK
RECLINERCUSHION
SEAT HAN-
DLE
XJ BODY 23 - 13
REMOVAL AND INSTALLATION (Continued)
(3) With the cushion side down, engage the for-
ward, rearward and inboard J-straps.
(4) Engage the clips attaching the outboard side of
the cover to the cushion frame.
(5) Install seatback.
(6) Install side shield trim cover.
(7) Install seat.
BUCKET SEAT RECLINER
REMOVAL
(1) Remove side shield trim cover.
(2) Disengage seatback cover zipper.
(3) Roll outer seatback cover upward.
(4) Remove bolts attaching recliner to seatback
Fig. 10 Bucket Seatback and seat cushion frames (Fig. 12).
(3) Install bolts attaching recliner to seat cushion (5) Separate recliner from seat.
frame.
(4) Install side shield trim cover.
BUCKET SEAT CUSHION COVER
REMOVAL
(1) Remove seat from vehicle.
(2) Remove side shield trim cover.
(3) Remove seatback.
(4) With the cushion side down, disengage the for-
ward, rearward and inboard J-straps.
(5) Disengage the clips attaching the outboard side
of the cover to the cushion frame.
(6) Turn the cushion over and roll the cover off the
cushion.
(7) Remove the hog rings attaching the cover to
the cushion support wires (Fig. 11). Fig. 12 Bucket Seat Recliner
(8) Separate the cover from the cushion.
INSTALLATION
(1) Position recliner on seat.
(2) Install bolts attaching recliner to seatback and
seat cushion frames (Fig. 12).
(3) Roll seatback cover downward.
(4) Engage seatback cover zipper.
(5) Install side shield trim cover.
REAR SEAT CUSHION COVER
REMOVAL
(1) Remove the seat cushion from the vehicle.
(2) Remove the cover side, front and rear retaining
clips from the wire retainers with an appropriate
removal tool (Fig. 13).
(3) Remove the serrated retainers from the front
ends of the cover with a trim panel removal tool (Fig.
Fig. 11 Seat Cushion Cover Hog Rings 14).
INSTALLATION (4) Remove the seat cover from the cushion.
(1) Position the cover on the cushion.
INSTALLATION
(2) Install the hog rings attaching the cover to the
(1) Position the replacement cover on the cushion.
cushion support wires.
14. SEAT REMOVER TOOL SEAT COVER
COVER CLIPS REMOVEROOL
CLIP T REAR WHEEL- FWD
HOUSE STRIKER
LATCH SCREW
TORX-HEAD
BRACKET SEATBACK
BRACKET
STRIKER SEATBACK
BUMPER
LATCH
BUMPER
STRIKER
LATCH
LATCH
STRIKER
BRACKET
23 - 14 BODY XJ
REMOVAL AND INSTALLATION (Continued)
(3) Release the seatback latch from the striker.
(4) Tilt the seatback forward for access to the
striker bracket.
(5) Remove the retaining screws and the latch
striker bracket from the trim panel (Fig. 15).
Fig. 13 Seat Cushion Cover Retaining Clip Removal
Fig. 15 Seatback Latch Striker Bracket Removal/
Installation
INSTALLATION
(1) Position the latch striker bracket on the trim
panel and install the retaining screws. Tighten the
screws with 6 N·m (50 in. lbs.) torque.
(2) Engage the seatback latch with the striker.
(3) Pivot the seat cushion to the horizontal posi-
tion and lock it in-place by pressing firmly on the
center of the cushion until the latch engages.
REAR SEATBACK COVER
REMOVAL
(1) Remove the seatback from the vehicle.
(2) Remove the seatback latch release handle and
bezel from the seatback.
Fig. 14 Seat Cushion Cover Retaining Clip Removal (3) Disengage the cover zippers.
(2) Compress the cover and attach the retaining (4) Disengage the J-strap attaching the cover to
clips to the front and rear wire retainers. the seat back frame (Fig. 16).
(3) Install the serrated retainers at the ends of the (5) Remove the cover from the seatback pad.
cover.
(4) Install the seat cushion in the vehicle. If neces-
sary, refer to the installation procedure.
REAR SEATBACK LATCH STRIKER AND BUMPER
REMOVAL
(1) Disengage the seat cushion at the rear by pull-
ing upward on the release strap.
(2) Tilt the seat cushion forward.
15. COVER ZIPPER SEAT BACK
XJ BODY 23 - 15
REMOVAL AND INSTALLATION (Continued)
(3) Engage the cover zippers.
(4) Install the seat latch release bezel and handle.
(5) Install the seatback in the vehicle.
SPECIAL TOOLS
SEATS
Extractor Head Restraint Sleeve 6773
Fig. 16 Seatback Cover Removal
INSTALLATION
(1) Install the cover on the seatback.
(2) Attach the cover J-strap to the seatback frame.
17. XJ BODY 23 - 17
REAR DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . 37 ADJUSTMENTS
REAR FENDER FLARE . . . . . . . . . . . . . . . . . . 42 DOOR LATCH ADJUSTMENT . . . . . . . . . . . . . . 59
REAR SEAT CUSHION . . . . . . . . . . . . . . . . . . . 51 DOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
REAR SEATBACK . . . . . . . . . . . . . . . . . . . . . . 52 HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
REAR SHOULDER/LAP BELT/BUCKLE . . . . . . 49 LIFTGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
REARVIEW MIRROR SUPPORT BRACKET . . . 53 SPECIFICATIONS
REARVIEW MIRROR . . . . . . . . . . . . . . . . . . . . 53 BODY LUBRICANTS . . . . . . . . . . . . . . . . . . . . 60
RIGHT FRONT FENDER . . . . . . . . . . . . . . . . . 26 TORQUE SPECIFICATIONS . . . . . . . . . . . . . . . 60
SAFETY LATCH STRIKER . . . . . . . . . . . . . . . . 22 SPECIAL TOOLS
SIDE VIEW MIRROR . . . . . . . . . . . . . . . . . . . . 25 BODY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SUNVISORS . . . . . . . . . . . . . . . . . . . . . . . . . . 53
DIAGNOSIS AND TESTING • If a leak occurs while driving at highway speeds
in a steady rain, test the leak area with a reasonable
WATER LEAKS velocity stream or fan spray of water. Direct the
Water leaks can be caused by poor sealing, spray in a direction comparable to actual conditions.
improper body component alignment, body seam • If a leak occurs when the vehicle is parked on an
porosity, missing plugs, or blocked drain holes. Cen- incline, hoist the end or side of the vehicle to simu-
trifugal and gravitational force can cause water to late this condition. This method can be used when
drip from a location away from the actual leak point, the leak occurs when the vehicle accelerates, stops or
making leak detection difficult. All body sealing turns. If the leak occurs on acceleration, hoist the
points should be water tight in normal wet-driving front of the vehicle. If the leak occurs when braking,
conditions. Water flowing downward from the front of hoist the back of the vehicle. If the leak occurs on left
the vehicle should not enter the passenger or luggage turns, hoist the left side of the vehicle. If the leak
compartment. Moving sealing surfaces will not occurs on right turns, hoist the right side of the vehi-
always seal water tight under all conditions. At cle. For hoisting recommendations refer to Group 0,
times, side glass or door seals will allow water to Lubrication and Maintenance, General Information
enter the passenger compartment during high pres- section.
sure washing or hard driving rain (severe) condi-
tions. Overcompensating on door or glass WATER LEAK DETECTION
adjustments to stop a water leak that occurs under To detect a water leak point-of-entry, do a water
severe conditions can cause premature seal wear and test and watch for water tracks or droplets forming
excessive closing or latching effort. After completing on the inside of the vehicle. If necessary, remove inte-
a repair, water-test vehicle to verify leak has stopped rior trim covers or panels to gain visual access to the
before returning vehicle to use. leak area. If the hose cannot be positioned without
being held, have someone help do the water test.
VISUAL INSPECTION BEFORE WATER LEAK Some water leaks must be tested for a considerable
TESTS length of time to become apparent. When a leak
Verify that floor and body plugs are in place, body appears, find the highest point of the water track or
drains are clear, and body components are properly drop. The highest point usually will show the point of
aligned and sealed. If component alignment or seal- entry. After leak point has been found, repair the
ing is necessary, refer to the appropriate section of leak and water test to verify that the leak has
this group for proper procedures. stopped.
Locating the entry point of water that is leaking
WATER LEAK TESTS into a cavity between panels can be difficult. The
trapped water may splash or run from the cavity,
WARNING: DO NOT USE ELECTRIC SHOP LIGHTS often at a distance from the entry point. Most water
OR TOOLS IN WATER TEST AREA. PERSONAL leaks of this type become apparent after accelerating,
INJURY CAN RESULT. stopping, turning, or when on an incline.
When the conditions causing a water leak have MIRROR INSPECTION METHOD
been determined, simulate the conditions as closely When a leak point area is visually obstructed, use
as possible. a suitable mirror to gain visual access. A mirror can
• If a leak occurs with the vehicle parked in a also be used to deflect light to a limited-access area
steady light rain, flood the leak area with an open- to assist in locating a leak point.
ended garden hose.
18. 23 - 18 BODY XJ
DIAGNOSIS AND TESTING (Continued)
BRIGHT LIGHT LEAK TEST METHOD ROAD TESTING WIND NOISE
Some water leaks in the luggage compartment can (1) Drive the vehicle to verify the general location
be detected without water testing. Position the vehi- of the wind noise.
cle in a brightly lit area. From inside the darkened (2) Apply 50 mm (2 in.) masking tape in 150 mm
luggage compartment inspect around seals and body (6 in.) lengths along weatherstrips, weld seams or
seams. If necessary, have a helper direct a drop light moldings. After each length is applied, drive the vehi-
over the suspected leak areas around the luggage cle. If noise goes away after a piece of tape is applied,
compartment. If light is visible through a normally remove tape, locate, and repair defect.
sealed location, water could enter through the open-
ing. POSSIBLE CAUSE OF WIND NOISE
• Moldings standing away from body surface can
PRESSURIZED LEAK TEST METHOD catch wind and whistle.
When a water leak into the passenger compart- • Gaps in sealed areas behind overhanging body
ment cannot be detected by water testing, pressurize flanges can cause wind-rushing sounds.
the passenger compartment and soap test exterior of • Misaligned movable components.
the vehicle. To pressurize the passenger compart- • Missing or improperly installed plugs in pillars.
ment, close all doors and windows, start engine, and • Weld burn through holes.
set heater control to high blower in HEAT position. If
engine can not be started, connect a charger to the
battery to ensure adequate voltage to the blower. SERVICE PROCEDURES
With interior pressurized, apply dish detergent solu-
tion to suspected leak area on the exterior of the BODY LUBRICATION
vehicle. Apply detergent solution with spray device or All mechanisms and linkages should be lubricated
soft bristle brush. If soap bubbles occur at a body when necessary. This will maintain ease of operation
seam, joint, seal or gasket, the leak entry point could and provide protection against rust and excessive
be at that location. wear. The weatherstrip seals should be lubricated to
prolong their life as well as to improve door sealing.
WIND NOISE All applicable exterior and interior vehicle operat-
Wind noise is the result of most air leaks. Air leaks ing mechanisms should be inspected and cleaned.
can be caused by poor sealing, improper body compo- Pivot/sliding contact areas on the mechanisms should
nent alignment, body seam porosity, or missing plugs then be lubricated.
in the engine compartment or door hinge pillar areas. (1) When necessary, lubricate the operating mech-
All body sealing points should be airtight in normal anisms with the specified lubricants.
driving conditions. Moving sealing surfaces will not (2) Apply silicone lubricant to a cloth and wipe it
always seal airtight under all conditions. At times, on door seals to avoid over-spray that can soil pas-
side glass or door seals will allow wind noise to be senger’s clothing.
noticed in the passenger compartment during high (3) Before applying lubricant, the component
crosswinds. Over compensating on door or glass should be wiped clean. After lubrication, any excess
adjustments to stop wind noise that occurs under lubricant should be removed.
severe conditions can cause premature seal wear and (4) The hood latch, latch release mechanism, latch
excessive closing or latching effort. After a repair pro- striker, and safety latch should be lubricated period-
cedure has been performed, test vehicle to verify ically.
noise has stopped before returning vehicle to use. (5) The door lock cylinders should be lubricated
Wind noise can also be caused by improperly fitted twice each year (preferably autumn and spring):
exterior moldings or body ornamentation. Loose • Spray a small amount of lock cylinder lubricant
moldings can flutter, creating a buzzing or chattering directly into the lock cylinder.
noise. An open cavity or protruding edge can create a • Apply a small amount to the key and insert it
whistling or howling noise. Inspect the exterior of the into the lock cylinder.
vehicle to verify that these conditions do not exist. • Rotate it to the locked position and then back to
the unlocked position several times.
VISUAL INSPECTION BEFORE TESTS • Remove the key. Wipe the lubricant from it with
Verify that floor and body plugs are in place and a clean cloth to avoid soiling of clothing.
body components are aligned and sealed. If compo-
nent alignment or sealing is necessary, refer to the
appropriate section of this group for proper proce-
dures.
19. GRILLE OPENING PANEL NUT GRILLE FWD
BODY GRILLE BRACKET
SUPPORT
OPENING
PANEL
XJ BODY 23 - 19
REMOVAL AND INSTALLATION
GRILLE
REMOVAL
(1) Remove the headlamp/park lamp bezels.
(2) Remove the screws attaching the grille to the
grille opening panel (GOP) (Fig. 1).
(3) Separate the grille from the GOP.
Fig. 2 Grille Opening Panel
(5) Install nuts attaching GOP to front fenders.
Tighten nuts to 4 N·m (38 in-lbs) torque.
(6) Install headlamps and park/turn signal lamps.
(7) Install headlamp bezels.
(8) Install side marker lamps.
(9) Install grille.
(10) Adjust headlamp aim, if necessary.
Fig. 1 Grille HOOD
INSTALLATION
REMOVAL
(1) Position the grille in the GOP.
(1) Raise hood.
(2) Install the screws.
(2) Disconnect underhood lamp wire harness con-
(3) Install the headlamp/park lamp bezels.
nector, if equipped.
(3) Disconnect release cable from latch release
GRILLE OPENING PANEL (GOP)
bellcrank.
REMOVAL (4) Remove latch release cable clips and remove
(1) Remove grille. cable from hood (Fig. 3).
(2) Remove headlamp bezels. (5) Mark location of hood, hinges and hinge shims
(3) Remove side marker lamps. for installation.
(4) Remove headlamps and park/turn signal (6) Remove bolts that attach hinges to hood.
lamps. (7) Remove hood from vehicle with aid of a helper.
(5) Open hood.
INSTALLATION
(6) Remove nuts that attach GOP to front fenders
(1) Position hood on shims and hinges; finger-
(Fig. 2).
tighten hinge bolts.
(7) Remove nuts attaching GOP to support
(2) Align hinges and shims with reference marks
bracket.
and tighten hinge bolts.
(8) Pull GOP forward and disconnect harness clips
(3) Connect latch release cable and latch connect-
and front lamp harness connectors.
ing rod to bellcrank.
(9) Remove GOP from vehicle.
(4) Attach latch release cable to clips.
INSTALLATION (5) Connect underhood lamp wire harness connec-
(1) Place GOP on bumper and secure all harness tor.
clips.
(2) Connect all lamp wire harness connectors. HOOD HINGE
(3) Position GOP on vehicle.
REMOVAL
(4) Install nuts attaching GOP to support bracket.
(1) Raise and support hood.
Tighten nuts to 4 N·m (38 in-lbs) torque.
21. DASH PANEL
NUT HOOD HINGE HINGE SEAL
BASE HOOD LATCH
ROD SPRING
HOOD LATCH CONNECTING
RODRETAINER CLIP
XJ BODY 23 - 21
REMOVAL AND INSTALLATION (Continued)
(2) Using a grease pencil or equivalent, mark posi-
tion of hood.
(3) Remove seal from hinge base (Fig. 4).
(4) Remove hinge retaining nuts from studs.
Fig. 5 Hood Latch
(4) Remove the headlamp with mounting bucket
attached from the adjusting screws.
(5) Remove the upper bolt attaching the striker to
Fig. 4 Hood Hinge and Seal the top of the (GOP).
INSTALLATION (6) Remove the lower bolt attaching the striker to
(1) Position hinge over studs and align with refer- the (GOP).
ence marks. (7) Remove the striker and shims.
(2) Install nuts.
INSTALLATION
NOTE: If a replacement hinge seal is being (1) Position the shims and striker on the (GOP)
installed, position it around hinge arm, force it and install the bolts.
against hinge base. (2) Install the headlamp and mounting bucket.
(3) Install parklamp.
(3) Position hinge seal around hinge arm and on (4) Install the headlamp bezel.
hinge base. (5) Test the striker/hood alignment by opening and
(4) Adjust hood as necessary. closing the hood several times. Adjust the striker, if
necessary.
HOOD LATCH
HOOD RELEASE CABLE
REMOVAL
(1) Remove the screw that attaches the latch to REMOVAL
the hood inner panel (Fig. 5). (1) Drill out bellcrank to hood rivet heads and
(2) Disconnect the latch connecting rod. remove rivets (Fig. 6).
(3) Remove the latch from the hood. (2) Disconnect bellcrank from latch rod and hood
release cable. Remove bellcrank from hood.
INSTALLATION (3) Disconnect hood release cable from clips on
(1) Connect the latch to the latch connecting rod hood.
and (4) Remove left cowl side trim panel.
(2) Position the latch on the hood inner panel. (5) Remove cable bracket screws from cowl side
(3) Install the screw that attaches the latch to the panel.
hood inner panel. (6) Route cable through dash panel and remove it
from under instrument panel.
HOOD LATCH STRIKER
INSTALLATION
REMOVAL (1) Insert replacement cable end through hole in
(1) Remove headlamp bezel. dash panel into engine compartment.
(2) Remove parklamp. (2) Route cable forward and seat grommet in dash
(3) Release the spring attaching the headlamp panel.
mounting bucket to the grille opening panel (GOP).
22. LATCH HOOD SAFETY LATCH
NUT CONNECTING
ROD HOOD BUMPER
RIVET HOOD INNER CABLE
RELEASE
LATCHSTUD
BELLCRANK
HOOD
PANEL RADIATOR SUPPORT
HOOD HOOD
CROSSMEMBER
RETAINERSAFETY STRIKER
LATCH SILENCER PAD
RADIATOR
SCREW
BRACKET
GOP
23 - 22 BODY XJ
REMOVAL AND INSTALLATION (Continued)
SAFETY LATCH STRIKER
REMOVAL
(1) Remove striker screws from radiator support
crossmember (Fig. 8).
(2) Remove striker from crossmember.
Fig. 6 Hood Release Cable Bellcrank
(3) Position cable bracket on cowl side panel and
install screws.
(4) Install left cowl side trim panel.
(5) Connect cable and latch rod to bellcrank.
(6) Position bellcrank on hood and install rivets.
(7) Attach cable to clips. Fig. 8 Hood Safety Latch Striker
(8) Test release cable for proper operation. INSTALLATION
(1) Position striker on radiator support crossmem-
HOOD SAFETY LATCH ber and install screws.
(2) Test safety latch operation.
REMOVAL
(1) Open and support hood.
HOOD SILENCER PAD
(2) Remove the nuts attaching the safety latch to
the inner hood panel (Fig. 7). REMOVAL
(3) Separate the safety latch from the hood. (1) Open and support hood.
(2) Remove the hood latch release bellcrank.
(3) Remove the clips attaching the latch connect-
ing rod to the hood inner panel.
(4) Remove the retainers attaching the hood
silencer pad to the inner hood panel (Fig. 9).
(5) Separate the hood silencer pad from the hood.
Fig. 7 Hood Safety Latch
INSTALLATION
(1) Position the safety latch on the hood.
(2) Install the nuts attaching the safety latch to
the inner hood panel.
(3) Close hood.
Fig. 9 Hood Silencer Pad
23. WEATHERSTRIPCOWL
DASH PANEL
SEAL
THICK-HEAD RETAINER FLAT-HEAD RETAINER COWL
PLASTIC
PANEL PUSH-
RIVET
FWD GRILLE NOZZLE SCREEN
SCREEN RIVET AND SCREW
GRILLE
NOZZLE
SCREEN
GRILLE
PLASTIC PUSH-
RIVET
XJ BODY 23 - 23
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Position the hood silencer pad on the hood
inner panel.
(2) Install the retainers attaching the hood
silencer pad to the inner hood panel.
(3) Install the clips attaching the latch connecting
rod to the hood inner panel.
(4) Install the hood latch release bellcrank.
(5) Close hood.
COWL WEATHERSTRIP
REMOVAL
(1) Pry upward along the length of weatherstrip.
(2) Detach the weatherstrip retainers from the
cowl panel (Fig. 10).
(3) Remove the weatherstrip from cowl panel.
Fig. 11 Cowl Grille, Screen & Washer Nozzles
(1) Position the cowl grille and screen on the cowl.
(2) Install the windshield washer tubes on the noz-
zles.
(3) Install the cowl screen and grille screws.
Tighten in sequence (Fig. 12).
NOTE: Force the cowl grille rearward while tighten-
ing the screws.
(4) Install the windshield wiper arms on the piv-
ots.
Fig. 10 Cowl Weatherstrip
INSTALLATION
(1) Position the weatherstrip on the cowl panel.
(2) Press to insert retainers into the cowl panel
holes.
COWL GRILLE
REMOVAL
(1) Remove the windshield wiper arms from the
pivots.
(2) Remove the screws that attach the grille to the Fig. 12 Cowl Grille Screw Tightening Sequence
cowl.
(3) Remove the windshield washer tubes from the BODY DECALS
nozzles. Small nicks, scratches and other surface marks in
(4) Remove the cowl grille and screen from the a decal can be touched-up with paint.
cowl (Fig. 11). To eliminate blisters and air bubbles in a decal,
pierce them with a needle or pin.
INSTALLATION A heat gun can also be used to remove small wrin-
kles in a decal.
CAUTION: The washer fluid tubes must be routed Decal replacement requires that the metal repair
and installed so that they are not pinched. and paint refinish be completed first.