Flare Electricals manufactures complete range of accessories for earthing and lightning protection system. An earthing and lightning protection system protects structures against destruction caused by lightning. A good earthing and lightning protection system consists of air termination network, down conductors, and earth termination network. Air termination network protects the structure by capturing lightning current and dissipating it to the ground. Down conductors provide the path for lightning current to pass from air termination network to ground. An earthing termination network dissipates the electric current safely to the ground.
Grey Hawk’s range of Earthing and Lightning Protection System consists of Copper Bonded Steel Earth Rods, Pure Copper Earth Rods, Driving Studs, Couplers, Copper Conductors, Rod to Cable Clamps, Rod to Tape Clamps, Cable Saddles, Square Tape Clamp, Tapered Air Rods, Multipoint, Air Terminal Base, Air Rod Ridge Saddle, Air Rod Bracket, GUV Clamps, U Bolt Clamps, Earth Bars, Earth Pits etc.
Bare Metal Flexible Steel Conduits are standard Industrial Conduits with Galvanized sheet steel inner core without PVCu oversheath. Helically wound with single clutch, this conduit is manufactured from galvanized steel conforming to Z275 specification. The product is supplied in steel self finish. The conduits are also available in Stainless Steel.
Aluminium Cable Cleats play a very important role in cable installations. The cable must be clamped appropriately during installations to restrict the movement of cables due to fault current magnetic forces and thereby avoid damage.
Grey Hawk’s Aluminium Cable Cleats are made of high quality cast aluminium and manufactured in accordance with BS EN 61914:2009 standard. They are supplied with SS 304 fasteners and optional neoprene liners.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
Grey Hawk’s range of Earthing and Lightning Protection System consists of Copper Bonded Steel Earth Rods, Pure Copper Earth Rods, Driving Studs, Couplers, Copper Conductors, Rod to Cable Clamps, Rod to Tape Clamps, Cable Saddles, Square Tape Clamp, Tapered Air Rods, Multipoint, Air Terminal Base, Air Rod Ridge Saddle, Air Rod Bracket, GUV Clamps, U Bolt Clamps, Earth Bars, Earth Pits etc.
Bare Metal Flexible Steel Conduits are standard Industrial Conduits with Galvanized sheet steel inner core without PVCu oversheath. Helically wound with single clutch, this conduit is manufactured from galvanized steel conforming to Z275 specification. The product is supplied in steel self finish. The conduits are also available in Stainless Steel.
Aluminium Cable Cleats play a very important role in cable installations. The cable must be clamped appropriately during installations to restrict the movement of cables due to fault current magnetic forces and thereby avoid damage.
Grey Hawk’s Aluminium Cable Cleats are made of high quality cast aluminium and manufactured in accordance with BS EN 61914:2009 standard. They are supplied with SS 304 fasteners and optional neoprene liners.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
Flare Electricals range of A1/A2 Cable Glands are manufactured from high quality brass. These are used for unarmored cables, rubber or plastic sheathed cables. Larger sizes are made by sand casting technique while smaller sizes are made from extruded rods. A superior quality rubber gasket is used inside the gland to act as sealing material and also to help in weather protection. The gland comes in kit with earth tag and a shroud. Shroud is provided for additional ingress protection.
Flare Electricals range of Cable Glands come in size 20 to 75.
Save time and cost using customer arrays of domes. Available with retainer layer, or retainer and spacer. You can add shielding or use black or white materials
Specially designed for tie top insulators, This type clamp features a long steel stud for
mounting on a variety of different diameter insulators. Nuts are captive at both ends for
ease off installation. A single bolt clamping feature makes conductor installation possible
with a standard wrench or hot stick without removing parts. Only three clamp sizes are
required for conductor diameters from .25 to 1.5 inches. No parts need be removed for
assembly to insulators or clipping in conductor. All cast parts are high strength heat treated
356-T6 aluminum alloy. Steel parts are hot dip galvanized for maximum corrosion
resistance. This series is also available in all-aluminum clamp having a cast 356-T6 high
strength heat treated aluminum body, keeper, and clamp with aluminum alloy stud, nuts,
and lockwashers. To order all-aluminum clamp specify catalog number using suffix AA. For
correct clamp size to use with a given conductor, and neck sizes of pin and post type
insulators, refer to tables in the engineering Data Section of this catalog.
If you are looking for Storage Containers for sale or rent so feel free to contact Anjerinc we providing Storage Containers in Pennsylvania, Delaware and New Jersey. For more information feel free to visit our website - http://www.anjerinc.com
SEPCO Steel Electric Products Company was founded in 1938 as a metal fabricating and stamping company by Morris Reddock and his son Philip, and incorporated in 1952. SEPCO carried a product line which included EMT and rigid one-hole and two-hole pipe straps, reducing washers and switch box supports. Malleable iron, steel and die-cast fittings were added to the product line and SEPCO now currently carries approximately 2,000 SKU's with trade sizes 1/2" - 6" on most product groups and is a leading manufacturer in the elctrical industry. All SEPCO products carry the full UL listing.
Flare Electricals range of A1/A2 Cable Glands are manufactured from high quality brass. These are used for unarmored cables, rubber or plastic sheathed cables. Larger sizes are made by sand casting technique while smaller sizes are made from extruded rods. A superior quality rubber gasket is used inside the gland to act as sealing material and also to help in weather protection. The gland comes in kit with earth tag and a shroud. Shroud is provided for additional ingress protection.
Flare Electricals range of Cable Glands come in size 20 to 75.
Save time and cost using customer arrays of domes. Available with retainer layer, or retainer and spacer. You can add shielding or use black or white materials
Specially designed for tie top insulators, This type clamp features a long steel stud for
mounting on a variety of different diameter insulators. Nuts are captive at both ends for
ease off installation. A single bolt clamping feature makes conductor installation possible
with a standard wrench or hot stick without removing parts. Only three clamp sizes are
required for conductor diameters from .25 to 1.5 inches. No parts need be removed for
assembly to insulators or clipping in conductor. All cast parts are high strength heat treated
356-T6 aluminum alloy. Steel parts are hot dip galvanized for maximum corrosion
resistance. This series is also available in all-aluminum clamp having a cast 356-T6 high
strength heat treated aluminum body, keeper, and clamp with aluminum alloy stud, nuts,
and lockwashers. To order all-aluminum clamp specify catalog number using suffix AA. For
correct clamp size to use with a given conductor, and neck sizes of pin and post type
insulators, refer to tables in the engineering Data Section of this catalog.
If you are looking for Storage Containers for sale or rent so feel free to contact Anjerinc we providing Storage Containers in Pennsylvania, Delaware and New Jersey. For more information feel free to visit our website - http://www.anjerinc.com
Composite hose couplings have special spiral hose ends designed to match with composite hoses and crimped with ferrules and seals. The composite hose couplings includes flange end, type C, type E, male thread, and female thread. Available in SS 316 and aluminum.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
2. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
SOLID COPPER EARTH ROD AND ACCESSORIES
Solid Copper Earth Rod
Pure Copper Earth Rods are made of pure (100%) electrolytic copper. The Earth Rods are hard drawn from extruded
copper bars. Pure copper earth rods are preferred where soil conditions are very aggressive & corrosive. The rods are
threaded internally to make it extensible for deep driving with the help of couplers.
Earth Rod Dia Length Thread Part No.
15mm 1200mm M10 FLE-SCER-15-1.2
15mm 1500mm M10 FLE-SCER-15-1.5
15mm 2400mm M10 FLE-SCER-15-2.4
16mm 1200mm M10 FLE-SCER-16-1.2
16mm 1500mm M10 FLE-SCER-16-1.5
16mm 2400mm M10 FLE-SCER-16-2.4
20mm 1200mm M10 FLE-SCER-20-1.2
20mm 1500mm M10 FLE-SCER-20-1.5
20mm 2400mm M10 FLE-SCER-20-2.4
* other sizes available on request
3. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Coupling Dowel
Coupling dowel made of brass, stainless steel or gunmetal is a threaded joining devise which joins two earth rods together
for extending earth rods in an earthing system
Thread Dia. Length Material Part No.
M10 40mm Brass FLE-CD-10
M12 40MM Brass FLE-CD-12
Driving Head
Driving heads are made of toughened steel and used while hammering an earth rod into ground. Driving head protects the
relatively soft earth rod from damage while hammering. Driving heads have no further function in earthing & lightning
protection.
Rod Dia. Thread Dia. Part No.
16 M10 FLE-DH-16
20 M10 FLE-DH-20
25 M12 FLE-DH-25
Driving Spike
Driving spikes are made of toughened steel and used as a pointed guide while hammering an earth rod into ground. The
pointed tip of driving spike pierces the soil so that earth rods are smoothly driven down the ground. Driving spikes have
no further function in earthing & lightning protection.
Rod Dia. Thread Dia. Part No.
16 M10 FLE-DS-16
20 M10 FLE-DS-20
25 M12 FLE-DS-25
4. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
COPPER BONDED STEEL EARTH ROD AND ACCESSORIES
Copper bonded steel earth rods are the most commonly used earth electrode. They are suitable for most application,
compatible for deep driving & are economical. Copper bonded steel earth rods are made by molecularly bonding 99.9%
pure copper onto high carbon, low tensile steel rods.
Thread Size Length Rod Dia. Part No.
5/8" 1200mm 13.70mm FLE-CBSER-58-1.2
5/8" 1500mm 13.70mm FLE-CBSER-58-1.5
5/8" 1800mm 13.70mm FLE-CBSER-58-1.8
5/8" 2400mm 13.70mm FLE-CBSER-58-2.4
5/8" 3000mm 13.70mm FLE-CBSER-58-3.0
3/4" 1200mm 16.70mm FLE-CBSER-34-1.2
3/4" 1500mm 16.70mm FLE-CBSER-34-1.5
3/4" 1800mm 16.70mm FLE-CBSER-34-1.8
3/4" 2400mm 16.70mm FLE-CBSER-34-2.4
3/4" 3000mm 16.70mm FLE-CBSER-34-3.0
* other sizes available on request
** we provide upto 250 micron copper coating on earth rods
5. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Coupler
Couplers made of brass, stainless steel or gunmetal is a threaded joining devise which joins two
earth rods together for extending earth rods in an earthing system.
Size Material Part No.
5/8" Brass FLE-C-58
3/4" Brass FLE-C-34
* other sizes available on request
** coupler available in other materials, Phosphor Bronze / Silicon Bronze /
Gunmetal
Driving Head
Driving heads are made of toughened steel and used while hammering an earth rod into ground.
Driving head protects the relatively soft earth rod from damage while hammering. Driving heads
have no further function in earthing & lightning protection.
Size Material Part No.
5/8" Steel FLE-DH-58
3/4" Steel FLE-DH-34
* other sizes available on request
6. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
LIGHTNING PROTECTION ACCESSORIES
Tapered Air Rod
Taper pointed air rod is a part of air termination network of a lightning protection system. Air rods are supplied with nuts
enabling the rod to be locked tight against the conductor. These taper pointed air rods are made of pure copper.
Thread Dia. Length in mm Part No.
M16 300 FLE -AR-01
M16 500 FLE-AR-02
M16 1000 FLE-AR-03
M16 1500 FLE-AR-04
M16 2000 FLE-AR-05
M20 300 FLE-AR-06
M20 500 FLE-AR-07
M20 1000 FLE-AR-08
M20 1500 FLE-AR-09
M20 2000 FLE-AR-10
7. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Multipoint
Multipoint is used in conjunction with the taper pointed air rods.
Air Rod Dia. In mm Part No.
16 and 20 FLE-MP
Air Terminal Base
Air rod base is used to support air rods on flat roof surfaces. Air rod base is made from copper alloy.
Thread Dia. Part No.
M16 FLE-ARS-16
M20 FLE-ARS-20
8. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Air Rod Ridge Saddle
These ridge saddles are used to support air rods on roof ridges.
Thread Dia. Part No.
M16 FLE-ARRS-16
Air Rod Brackets
Air rod brackets are used in conjunction with the rod to tape coupling used to secure the flat tape to air rod. These air
rod brackets are made from copper alloy.
Rod Size. Part No.
16 FLE-ARB-16
20 FLE-ARB-20
9. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
DC Tape Clips
D.C. tape clip secures the flat tape conductor to the building surface. These D.C. clips are made from Copper Alloy.
Conductor Size in
mm.
Part No.
20x3 FLE-DCTC-20x3
25x3 FLE-DCTC-25x3
25x6 FLE-DCTC-25x6
31x3 FLE-DCTC-31x3
31x6 FLE-DCTC-31x6
50x3 FLE-DCTC-50x3
50x6 FLE-DCTC-50x6
Copper Tape Clip
Copper tape clips hold the flat conductor to building surface. Copper Tape ClipS are made from pure copper.
10. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Conductor Size in
mm.
Part No.
20x3 FLE-TC-20x3
25x3 FLE-TC-25x3
Square Tape Clamps
Square tape clamps are suitable for making cross, straight through and Tee joints in flat tape. The base has a
countersunk hole in the middle for securing the clamp to the building surface and the lid is fixed by means of four
screws. Square tape clamps are made from copper alloy.
Conductor Size in
mm.
Part No.
25x3 FLE-STC-25x3
25x6 FLE-STC-25x6
31x3 FLE-STC-31x3
31x6 FLE-STC-31x6
50x3 FLE-STC-50x3
50x6 FLE-STC-50x6
11. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Oblong Test Clamp
Oblong test clamp is used to join a range of tape sizes in straight through position. These clamps are also used to allow
the conductor to be overlapped by two set screws. These clamps are made from copper alloy.
Conductor Size in
mm.
Part No.
26x8 FLE-OTC-26x8
51x10 FLE-OTC-51x10
12. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
CLAMPS AND FITTINGS
Earthing clamps are used to connect earth electrode (earth rods) with conductors or tapes. The clamps are made of gunmetal.
Rod to Tape Clamp ( Type A )
Earthing clamps are used to connect earth electrode (earth rods) with conductors or tapes. A Type Clamps
are one type of earthing clamp, used to join earth rods and copper tapes. The earth rod and tape passes
through the clamp body and a screw fastener secures both together. Type A clamps are made of gunmetal or
brass.
Size Material Part No.
26 x 12mm Gunmetal FLE-A-2612
31 x 12mm Gunmetal FLE-A-3112
40 x 10mm Gunmetal FLE-A-4010
51 x 8mm Gunmetal FLE-A-5108
* A clamps are available in Brass also.
** Choice of fastners include MS / Brass / SS
13. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Rod to Cable Clamp ( Type G )
Earthing clamps are used to connect earth electrode (earth rods) with conductors or tapes. G Type Clamps
are one type of earthing clamp, used to join earth rods and copper circular conductors. The earth rod and
conductor passes through the clamp body and a screw fastener secures both together. G clamps are made of
gunmetal or brass.
Size Material Part No.
1/2" Gunmetal FLE-G-12
5/8" Gunmetal FLE-G-58
3/4" Gunmetal FLE-G-34
1" Gunmetal FLE-G-1.0
* G clamps are available in Brass also.
** Choice of fasteners include MS / Brass / SS
Rod to Cable Clamp (Type O)
These Clamps are used for joining earth rods to different sizes of Copper Conductor. Type O
clamp are made from Brass.
Size Material Part No.
5/8" Brass FLE-O-58
3/4" Brass FLE-O-34
** Choice of fasteners include MS / Brass / SS
14. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
U Bolt Rod Clamp ( Type E )
Earthing clamps are used to connect earth electrode (earth rods) with conductors or tapes. E Type Clamps
are one type of earthing clamp, used to join earth rods and copper tapes. The earth rod passes through the
clamp body while the copper tape is fitted through the U Bolt. E clamps are made of gunmetal or brass.
SIZE MATERIAL PART NO
16mm Gunmetal FLE-E-16
20mm Gunmetal FLE-E-20
25mm Gunmetal FLE-E-25
31mm Gunmetal FLE-E-31
38mm Gunmetal FLE-E-38
50mm Gunmetal FLE-E-50
* E clamps are available in Brass also. Available in Single and double plate.
** Choice of fasteners & U bolt include MS / Brass / SS.
U Bolt Rod Clamp ( Type GUV )
Earthing clamps are used to connect earth electrode (earth rods) with conductors or tapes. GUV Type
Clamps are one type of earthing clamp, used to join earth rods and copper circular conductors. The earth
rod and conductor passes through the clamp body and nuts and bolts secure both together. GUV clamps are
made of gunmetal or brass.
SIZE MATERIAL PART NO
16-70Sqmm Gunmetal FLE-GUV-1670
70-185Sqmm Gunmetal FLE-GUV-70185
150-300Sqmm Gunmetal FLE-GUV-150300
* GUV clamps are available in Brass also.
** Choice of fasteners & U bolt include MS / Brass / SS
15. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
PUB Type Clamp
PUB Type Clamps are one type of earthing clamp, used to join pipe with cable. PUV clamps are
made of gunmetal or brass.
Size Material Part No.
5/8" Gunmetal FLE-PUB-58
3/4" Gunmetal FLE-PUB-34
1" Gunmetal FLE-PUB-1.0
1 1/2" Gunmetal FLE-PUB-1.5
2" Gunmetal FLE-PUB-2.0
2 1/2" Gunmetal FLE-PUB-2.5
3" Gunmetal FLE-PUB-3.0
4" Gunmetal FLE-PUB-4.0
* PUB clamps are available in Brass also.
** Choice of fasteners & U bolt include MS / Brass / SS
16. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
Earth Plate
Earthing plates are used as a part of earthing network. They provide long lasting solution
where earth rods are unsuitable. Earthing plates are made of solid copper or mild steel
with copper bonding.
Size in mm Part No.
300x300x3mm FLE-EP-1
500x500x1.5mm FLE-EP-2
500x500x3mm FLE-EP-3
600x600x1.5mm FLE-EP-4
600x600x3mm FLE-EP-5
900x900x3mm FLE-EP-6
1000x1000x3mm FLE-EP-7
1200x1200x3mm FLE-EP-8
Earth Bar
No. of
Terminals
Length Width Part No.
6 400 90 FLE-EB-6
8 500 90 FLE-EB-8
10 650 90 FLE-EB-10
12 750 90 FLE-EB-12
14 850 90 FLE-EB-14
16 950 90 FLE-EB-16
18 1100 90 FLE-EB-18
17. FLARE ELECTRICALS LLP www.flareelectricals.com info@flareelectricals.com
20 1250 90 FLE-EB-20
22 1300 90 FLE-EB-22
24 1400 90 FLE-EB-24
26 1550 90 FLE-EB-26
28 1650 90 FLE-EB-28
30 1800 90 FLE-EB-30
* Available with Single and Double disconnecting links.