1. DHANANJAY MISHRA
Correspondence Address –
University of Petroleum and Energy Studies
Energy Acres PO Bidholi via Prem Nagar
Dehradun-248007(Uttarakhand), India
Tel:91-8006755733
Email:nirmaldj@rediffmail.com
CAREER OBJECTIVE
To pursue a highly rewarding career, seeking for a job in challenging and healthy work environment where I can
utilize my skills and knowledge efficiently for organizational growth
ACADEMIC PROFILE
Year(s)
Qualification -
Degree/Diploma/Certificate
Board/University College/Institute Percentage
2008-2009 High School CBSE
Saraf Public
School,Khatima
91.4
2010-2011 SSC CBSE
Little Flower
Children School,
Mau (up)
71
2012-16
B.Tech in Aerospace
Engineering with specialization
in Avionics
University of Petroleum
and Energy Studies
College of
Engineering Studies
2.45/4
Project Title: Development of strap down navigation system and integrating with GPS.
Mentor: Mr M .Raja
Description: An independent inertial navigation system with GPS aiding is developed and all the results
obtained are analyzed with help of MATLAB by interfacing the development board used for the
system to a laptop. A part of the inertial navigation system algorithm is processed in MATLAB
because of the complexity of the equations used to calculate position and velocity of a body.
Project Title: Designing a matched Filter for radar
Description: Matched filter is used to optimize signal to noise ratio at the receiving section of the radar. This is
done with the help of matlab codes by simulating the radar waves into the receiving section.
Project Title: Curvature Analysis and co-ordinate refinement Of rotor blade profile of Agusta Westland
A-129 helicopter
Description: Analyzing the curvature of an airfoil using porcupine curvature analysis in CATIA V5.
Calculation of various parameters using Ansys fluent.
Comparison of results with original airfoil parameters.
Project Title: 3D modeling of a Bombardier's Flight Global Wing skinUsing Catia V5
Description: 3D modeling of wing upper skin panel in flat pattern before short peening process using 2-D
drawings provided by the manufacturer.
Project title: Rear Cargo Door analysis of ATR-52C by Alenia Aeronautica
Description: Load path analysis on various parts of cargo door components.
Stress analysis of components using conventionalmethods and analytical solutions of cargo door
FE analysis of the door using ANSYS.
TRAINING AND PROJECT UNDERTAKEN

2. IJAME MAY 2015
 Method for Fatigue Life Estimation Using Modified Endurance Limit.
 Cumulative Fatigue Analysis And Life Cycle Determination of a Component
IJAME JULY 2015
 Airfoil refinement and curvature analysis
 Relevant experience in core design and analysis of aerospace and general engineering components.
 Expertise in hand calculations, sizing and detail design using conventional methods of stress analysis in
lined with the methods of Bruhn, Niu, ESDU data sheets, HSB and Structural manuals of the OEM.
 Expertise in design of aero structures and substantiating the design using Linear, non-linear FE analysis.
 Experience in F & DT to evaluate the life of the structure using various methods
 Working knowledge of G D & T
 Experience in cause and effect analysis (CEA) and failure mode and effect analysis (FMEA).
 JUNE 2013: Aero modelling workshop organized by Aerospace Dept.
 NOV 2014- DEC 2014: Embedded Systems and Robotics.
 NOV 2014- Quad copter workshop organized by IIT ROORKEE
 July 2014-May 2015: Currently studying ADVANCED STRUCTURAL DESIGN AND PRACTICAL
STRESS ANALYSIS organized by Aerosphere
 June 2015- July 2015: Internship on aircraft structures under Aerosphere Pvt. Ltd. Chandigarh
 Part of organizing committee of ASME (American Society Of Mechanical Engineers),
 Participated in cricket team at national level in college time.
 Currently serving aeroclub (official club of aerospace dept. upes) as technical head.
 Attended flight laboratory under Dr. A.K Ghosh in IIT KANPUR related to flight testing and engine
performance.
MECHNICAL AND TECHNICAL SKILLS
 Programming Languages :C, C++
 Operating Systems : Windows XP/Windows Vista/Windows7, UNIX, LINUX
 Software &Tools :MS Word, MS PowerPoint, MS Excel, CATIA, DBMS, Ansys,
FLUENT, Nastran, Patran.
 Attended workshops :Quadcoptor, embedded systems and robotics( BY CETPA)
CAD Packages:
 CATIA V5 R16-19: Aerospace Sheet Metal Design, Generative Sheet Metal Design, Part Design,
Generative Shape Design, Drafting, Assembly Design.
 Solid works
FEA Packages:
 Ansys: Modal, Static structural, Fluid flow (fluent), Linear Buckling, Rigid Dynamics, Explicit Dynamics,
Crash test analysis.
 Nastran
 Patran
Research Paper
CURRICULAR ACHIEVEMENTS
EXTRA CURRICULAR ACHIEVEMENTS

3. PERSONAL DETAILS
Date of Birth : 18-12-1993
Father’s Name : Mr. Arunkumar Mishra
Mother’s Name : Mrs. Lalita Mishra
Category : General
Gender : Male
Nationality : Indian
Home Town : Khatima (Uttarakhand)
Permanent Address : Uttarakhand gramin bank vill and p/o chakarpur (uk)
Languages Known : Hindi, English
Mobility : Willing to relocate anywhere in India and overseas.
I hereby declare that the above information is correct to the best of my knowledge.
DHANANJAY MISHRA