The CV provides details about Eng. Mohammed Farid Ahmed Abdellatif including his contact information, age, education history, projects completed during his engineering studies focusing on electrical design and control systems, work experience as an electrical engineer for various companies in Egypt and Saudi Arabia installing and maintaining electrical systems, and additional skills including programming PLCs and simulation software.

1. [Type text]
CV (Curriculum Viate)
Eng. Mohammed farid ahemd abdellatif
Age: 26
Home phone: 002035378479
(at Egypt)00201206901022-(at KSA)009660545549935Mobil:
From 63 street branched from 30 street behind fadaly school sedi-
beshr ,Almontaza,Alexandria,Egypt
eemohammed3@gmail.commail:-E
Objective
I can develop my personal experience by training and working in
companies, as it will give me more knowledge in my electrical field
and give me the chance to work in these companies.
Personal information
Date of birth: 14 November 1988
Place of birth: mohrm-bek, Alexandria, Egypt
Marital status: single
Military service: fully exempted
Languages: Arabic (mother language), English (very good)
Faculty of Engineering, Electrical Power Department 2011, Alexandria
University
Electrical Projects during my engineering life:
(by using logic gate ICs)Electrical clock
Design of conveyor with counter of cans
(by using PIC controller & infrared sensors, conveyor
transfer cans with counting)
Design of Robot to par cipate in Robocon 2010

2. [Type text]
(by using PIC controller to control DC motors)
HVAC Design of Hospital and calculating area of Ducts
needed with its control circuits
for illuminationDialux2007 for duct design,AutoCADing(by us
design and PIC controller for circuit control )
This project is designed under the supervision of Dr. Ashraf
Ibrahim Megahd
Electrical Design of building consists of 36 floors
from Schneider under3.36Ecodial(by using
supervision of Dr. Amr Abo-Ghzala)
Control of DC motor using power electronics
(1st
, 1st
& 2nd
, 4 quadrant chopper circuits
controlled by PIC with PCB boards, this project is
designed under the supervision of Dr. Mohammed
Tawfik )
My graduation project is design of low and medium
voltage of electrical system distribution of cario
Marriott hotel
this project under supervision of :
1-Dr.Ahmed helmy rashed
2-Dr.Medhet elgenediy
And the examiner Dr.Abdelmon’m mossa
experience:Personal
ervision of Dr.in 2009 under supS7 PLC BASIC
Mohammed Tawfik.
from Ministry of Trade and Industry forCertificate
single phase and threeattending practical course about
in 2009.phase motor winding

3. [Type text]
Electricalwith excellent grade fromCertificate
in 2010.Distribution Department in Rasafa company
for Petroleum line pipes.SUMEDfromCertificate
Works at company for cars spare parts.
-(from 1company as electrical engineertiaSatorksW
2012 to 1-2013).
company as electricalb international-harcoPatorksW
engineer(maintenance and construc on) (from 1-2013
to 1-2015).
Bosch(of 2 factories vialstartupI attendb-Pharco(At
)oschB(alsowith the German expertsand LVPmachines)
)Socomec(,connect 2 UPSand make IQ &OQ with them
in 11KV level andsand RMU)Mitsubishigenerator(and 1
2 transformers and ATS panels ,work at oral factory and
(Rota andand ampoule factory)Romaco(vial factory
and WFI plastic ampoulemachines)oschB
factory)Bosch(and at LVPmachine)Rommelag(factory
and I deal with 2 kind of autoclaves system ,work at
s andutilmS(water treatment units for produce WFI
,and I design some circuits with classic control)oschB
ompactCsystem and with ladder systems used in PLC (
) in some application at myelio and logoZlikePLC
company) .
imaticSdify hardware configuration inwe moharcoPAt
) with the newASCOto replace old pneumatics(manger
) at one of water treatment station.FESTO(
asArabia (KSA)Saudicompany atGetcoatWorks
electrical engineer (construction and maintenance) from
(1-2015 ll now)
electrical works ;I installsible for allI am responGetcoAt
and Connect 8 transformer,4 RMUs ,3

4. [Type text]
, motion control center(MCC) panels)Perkins(generators
and PLC panels for all pump stations, install also switch
gear unit for medium voltage 13.8 KV,overhead
and install main) to power well pump stationsOHTLlines(
distribution panels (3 MDPs) for the station and connect
to step downececoSpanels from(power for all MCC
transformer 6 MVA (33/13.8 KV) to switch gear to RMUs
to step down transformers (13.8KV/400V) and to MDPs
to finally MCCs)
I am responsible for complete install for 1 medium
voltage switch gear(MVSG),3MDPS,11 MCC Panels,4
RMU,8 TRANSFORMERS,AND attend all testing for all this
materials.
Install about 75 outdoor ligh ng poles in our project.
Redesign the calculation for the loads and selection for
all Low voltage cables in the station)
Make modification for control circuit for some of MCC
panels that’s about construction works .
And what about control and scada work I make selection
for instruments we use in plant and select also its power
and control cables for all plant according to approved
specifications and process& control philosophy
&(P&IDs).
I am responsible also about maintenance works at all
stations and increase efficiency of the stations.
Elective and additional courses:

5. [Type text]
Special machines
Electrical Drives using solid state
Additional skills
Excellent deal with internet and computer software and
hardware.
-Simatic manager for programming SiemensSDeal with
.PLC400)-7 (300
7 200-tep 7 micro win for programming sSDeal with
.PLC
Pac drive (controller and motionlauEDeal with
.control)
ware for programmingsoftlogoandelioZDeal with
).and Zeliologo(smart relay
.ESS software for simulation ladder circuitsDeal with
Multisim program for simulation.
Delegate boost for 4 years.
Member of Students Union at 4th
year.
EXELLENT:Graduation project grade
oodG:last yearGrade of
.4%63:Total grade