This document is an operation and maintenance manual for TH414C GC and TH417C GC telehandler models produced after specific serial numbers. It contains safety information, pre-operation checks, controls information, operating instructions, and maintenance procedures. The manual has sections covering general safety practices, inspections, controls, engine operation, loading and transport, approved attachments, capacity charts, and instructions for specific attachments. It is intended to be kept with the machine at all times for reference by operators.
Caterpillar cat th255 c telehandler operator and maintenance manualudjfjjskekkem
This document provides an operations and maintenance manual for a telehandler model TH255C. It contains 9 sections that cover general safety practices, pre-operation checks, controls and indicators, operation instructions, attachments and hitches, emergency procedures, maintenance, additional checks, and specifications. The manual emphasizes following approved procedures, wearing proper safety gear, understanding capacity limits, avoiding electrical hazards, preventing tip overs, and using caution when traveling, lifting loads, and operating on slopes.
Daewoo doosan solar 400 lc v crawler excavator parts catalogue manualfjjskekdm
This document provides a parts list for a cylinder block assembly, including:
- The cylinder block assembly part number and description
- Individual part numbers, descriptions, and quantities for each component
- Serial numbers and replacement part numbers where applicable
It lists over 30 individual parts that make up the cylinder block assembly, including the cylinder block itself, bearing caps, seals, bolts, and other components. Serial numbers and replacement part options are provided for some items.
Doosan 460 plus tier 3 skid steer loader parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various components of a diesel engine, including the cylinder block, gear housing, flywheel housing, cylinder head, intake manifold, exhaust manifold, cam shaft, crank shaft, piston, lubrication oil system, and cooling water system. It provides part numbers, descriptions, quantities, and other identifying information for over 50 individual parts across these various engine systems.
Daewoo doosan solar 500 lc v (500lcv) crawler excavator parts catalogue manualfjjskekdm
The document provides a parts list for a muffler assembly, listing part numbers, descriptions, and quantities. It notes that the muffler sub-assembly and muffler parts have been replaced or updated for certain serial number ranges. Replacement part numbers are provided where applicable.
Daewoo doosan solar 470 lc v crawler excavator parts catalogue manualfjjskekdm
This document provides a parts list for a main frame assembly. It includes 3 frames, 2 weights, bolts, washers, brackets, pins, plates, and bushings. Serial numbers and replacement part numbers are provided for some items.
Daewoo doosan solar 450 lc v crawler excavator parts catalogue manualfjjskekdm
The document provides a parts list and descriptions for a cylinder block assembly. It lists over 150 individual parts that make up the cylinder block, including the cylinder block itself, bearing caps, bolts, plugs, seals, switches, pipes, flanges, nozzles, hooks, and other components. The parts are organized by key number, part number, description, quantity, and other identifying information.
Daewoo doosan solar 420 lc v crawler excavator parts catalogue manualfjjskekdm
This document provides a parts list for a muffler assembly, including part numbers, descriptions, and quantities. It lists the main muffler assembly part number and individual components such as the muffler, mounting bracket, and replacement part numbers. Serial number ranges are provided to indicate applicability of specific part versions.
Kawasaki 60 z7 wheel loader service repair manual (serial no. 60d1 5001 and up)fjjskekdm
The document is a shop manual section about disassembling and assembling the control valve of a wheel loader. It contains detailed instructions and diagrams for removing and installing the control valve, as well as disassembling and assembling its individual components. The section provides maintenance and repair guidance.
Caterpillar cat th255 c telehandler operator and maintenance manualudjfjjskekkem
This document provides an operations and maintenance manual for a telehandler model TH255C. It contains 9 sections that cover general safety practices, pre-operation checks, controls and indicators, operation instructions, attachments and hitches, emergency procedures, maintenance, additional checks, and specifications. The manual emphasizes following approved procedures, wearing proper safety gear, understanding capacity limits, avoiding electrical hazards, preventing tip overs, and using caution when traveling, lifting loads, and operating on slopes.
Daewoo doosan solar 400 lc v crawler excavator parts catalogue manualfjjskekdm
This document provides a parts list for a cylinder block assembly, including:
- The cylinder block assembly part number and description
- Individual part numbers, descriptions, and quantities for each component
- Serial numbers and replacement part numbers where applicable
It lists over 30 individual parts that make up the cylinder block assembly, including the cylinder block itself, bearing caps, seals, bolts, and other components. Serial numbers and replacement part options are provided for some items.
Doosan 460 plus tier 3 skid steer loader parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various components of a diesel engine, including the cylinder block, gear housing, flywheel housing, cylinder head, intake manifold, exhaust manifold, cam shaft, crank shaft, piston, lubrication oil system, and cooling water system. It provides part numbers, descriptions, quantities, and other identifying information for over 50 individual parts across these various engine systems.
Daewoo doosan solar 500 lc v (500lcv) crawler excavator parts catalogue manualfjjskekdm
The document provides a parts list for a muffler assembly, listing part numbers, descriptions, and quantities. It notes that the muffler sub-assembly and muffler parts have been replaced or updated for certain serial number ranges. Replacement part numbers are provided where applicable.
Daewoo doosan solar 470 lc v crawler excavator parts catalogue manualfjjskekdm
This document provides a parts list for a main frame assembly. It includes 3 frames, 2 weights, bolts, washers, brackets, pins, plates, and bushings. Serial numbers and replacement part numbers are provided for some items.
Daewoo doosan solar 450 lc v crawler excavator parts catalogue manualfjjskekdm
The document provides a parts list and descriptions for a cylinder block assembly. It lists over 150 individual parts that make up the cylinder block, including the cylinder block itself, bearing caps, bolts, plugs, seals, switches, pipes, flanges, nozzles, hooks, and other components. The parts are organized by key number, part number, description, quantity, and other identifying information.
Daewoo doosan solar 420 lc v crawler excavator parts catalogue manualfjjskekdm
This document provides a parts list for a muffler assembly, including part numbers, descriptions, and quantities. It lists the main muffler assembly part number and individual components such as the muffler, mounting bracket, and replacement part numbers. Serial number ranges are provided to indicate applicability of specific part versions.
Kawasaki 60 z7 wheel loader service repair manual (serial no. 60d1 5001 and up)fjjskekdm
The document is a shop manual section about disassembling and assembling the control valve of a wheel loader. It contains detailed instructions and diagrams for removing and installing the control valve, as well as disassembling and assembling its individual components. The section provides maintenance and repair guidance.
Doosan mega 160 wheeled loader parts catalogue manualfjjskekdm
The document provides a parts list and exploded diagram of a cylinder head assembly. It lists over 100 individual part numbers, descriptions, quantities, serial numbers and replacement part information. The cylinder head assembly drawing shows the components of the cylinder head including the head, valves, guides, seats, plugs and related mounting hardware.
Doosan e85 compact excavator parts catalogue manualfjjskekdm
This document contains a parts list and descriptions for a cylinder block assembly. It lists 31 individual parts that make up the cylinder block including the block itself, plugs, bolts, bushes, pins, and other components. It provides the part number, description, quantity, and other identifying information for each part.
Doosan e80 compact excavator parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various components of an engine, including the cylinder block, gear housing, flywheel housing, oil pan, cylinder head, suction manifold, exhaust manifold, camshaft, crankshaft, pistons, and lubrication oil system. It lists part numbers, descriptions, quantities, and other identifying information for each numbered part in the diagrams.
Doosan e63 compact excavator parts catalogue manualfjjskekdm
This document provides a parts list and descriptions for various components of an engine, including:
- The cylinder block assembly and related plugs and bolts.
- The gear housing, oil pump, seals, bolts, and covers.
- The flywheel housing, oil pan, seals, and bolts.
- The cylinder head, valves, springs, seals, bolts, and related components.
- The intake manifold, sensors, bolts, and throttle body.
- The exhaust manifold and pipes, sensors, bolts, EGR components, and heat exchanger.
- The DPF muffler, sensors, pipes, bolts, and mounting components.
Doosan e55 w compact excavator parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various engine components including the cylinder block, gear housing, flywheel housing, cylinder head, intake manifold, exhaust manifold, cam shaft, crank shaft, piston, lubrication oil system, and cooling water system. It includes over 75 individual parts with descriptions and quantities for each component.
Doosan dl420 a wheeled loader parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various components of a diesel engine. It includes lists of parts, part numbers, descriptions and quantities for items like the cylinder block, timing gear case, flywheel housing, driving system, cylinder head, cylinder head cover, and timing system. Serial numbers are provided for some replaceable parts.
Doosan dl200 tc wheeled loader parts catalogue manualfjjskekdm
This document provides a parts list and diagrams for the cylinder head and related components of a diesel engine. It includes images and lists of parts with descriptions, part numbers, quantities, serial numbers and replacement part information. The list contains over 75 individual part items or assemblies that make up the cylinder head, valves, springs, guides, cover, gaskets and related hardware.
This document provides specifications, maintenance schedules, and adjustment procedures for a service manual. It includes electrical specifications and speeds, hydraulic specifications, torque specifications, lubrication charts, and planned maintenance schedules. It also provides instructions for adjusting components like the brake, brake interlock switch, steering, lift chains, speed limiting switch, and SCR card trimpots.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjjskekdm
This document provides instructions for removing and installing steering clutches on a D5C III track-type tractor. Key steps include draining oil from the steering clutch compartment, removing components like the battery and control valve, and taking apart the clutch assembly by removing items such as the cylinder, piston, springs, and drums. Reassembly requires reinstalling these components in reverse order and making adjustments to ensure proper clearance and operation.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjjskekdm
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 6zl) serv...fjjskekdm
The document provides instructions for removing and installing the transmission oil pump and pump drive gear on a D5C III track-type tractor. Key steps include draining the transmission oil, removing the tube assembly, plate, and transmission oil pump. The pump drive gear is then removed from the transmission case. Reinstallation involves reversing these steps, ensuring proper positioning of seals and connections of hoses and rods.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 5hs) serv...fjjskekdm
This document provides instructions for removing and installing final drives on Caterpillar D5C III track-type tractors. It outlines 15 steps to remove the final drive, which include draining fluid, removing guards, bolts and sprocket segments. It then describes 21 steps to install the final drive, including applying sealant, installing sprocket segments and filling with oil. The document also describes 33 steps to disassemble the final drive into additional components like bearings, seals, gears and housings.
Caterpillar cat 966 h wheel loader (prefix tal) service repair manual (tal000...fjjskekdm
This document provides instructions for disassembling and assembling the freewheel stator component of a 966H wheel loader torque converter. It contains 34 steps for disassembly, removing components like bolts, seals, gears and bearings. The 19 assembly steps list installing these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools required include link brackets, drivers, and retaining ring pliers.
Caterpillar cat 966 h wheel loader (prefix ryf) service repair manual (ryf000...fjjskekdm
This service repair manual provides instructions for disassembling and assembling the power train of Caterpillar 966H and 972H wheel loaders. It describes removing the torque converter, transmission, and transfer gears from the vehicle. It then provides step-by-step instructions for disassembling the individual components of the torque converter, including removing gears, seals, shafts, housings, and other internal parts. Safety notices are included to warn technicians to contain fluids and release pressures before conducting repairs.
Caterpillar cat 966 h wheel loader (prefix bj6) service repair manual (bj6000...fjjskekdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting tools before removing bolts and the flywheel.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and ensuring proper alignment of gears. Tools and torque specifications are also provided.
Caterpillar cat 962 k wheel loader (prefix x4t) service repair manual (x4t000...fjjskekdm
This document provides instructions for disassembling and assembling the piston pump of the steering system on a Caterpillar 962K wheel loader. The disassembly procedure outlines 28 steps to remove components like bolts, valves, spools, springs, and bearings. The assembly procedure describes 34 steps and cautions to install these components in reverse order while following safety precautions for parts under spring tension. Tolerances are provided for adjusting axial shaft end play during assembly.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjjskekdm
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before working on hydraulic systems.
Caterpillar cat 962 k wheel loader (prefix fll) service repair manual (fll000...fjjskekdm
This document provides instructions for disassembling and assembling the piston pump of the steering system on a 962K wheel loader. The disassembly procedure involves removing 28 individual parts in sequential order, including spools, plugs, springs, and bearings. The assembly procedure instructs assembling the piston pump in the reverse order and notes safety precautions for parts under spring tension.
Caterpillar cat 320 l track type excavator (prefix 9kk) service repair manual...fjjskekdm
The document provides instructions for installing a crankshaft rear seal on a 320L excavator model. It describes using a seal installer tool and locator bolt to push the new wear sleeve with seal onto the crankshaft. It also describes installing a flywheel housing by cleaning surfaces, installing a new gasket and bolts, and installing an oil seal with another tool. Finally, it describes removing and installing a crankshaft pulley by using puller and installer tools and cleaning/lubricating mating parts of a new crankshaft front seal.
Caterpillar cat 320 l track type excavator (prefix 7wk) service repair manual...fjjskekdm
This document provides instructions for installing and removing various engine components on Caterpillar 320 and 320L track-type excavators powered by a 3116 engine. It describes how to install the crankshaft rear seal carrier using specific tools and sealants. It also provides directions for removing and installing the flywheel housing, vibration damper and pulley. Technicians are advised to keep components clean and contain fluids during repair work.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Doosan mega 160 wheeled loader parts catalogue manualfjjskekdm
The document provides a parts list and exploded diagram of a cylinder head assembly. It lists over 100 individual part numbers, descriptions, quantities, serial numbers and replacement part information. The cylinder head assembly drawing shows the components of the cylinder head including the head, valves, guides, seats, plugs and related mounting hardware.
Doosan e85 compact excavator parts catalogue manualfjjskekdm
This document contains a parts list and descriptions for a cylinder block assembly. It lists 31 individual parts that make up the cylinder block including the block itself, plugs, bolts, bushes, pins, and other components. It provides the part number, description, quantity, and other identifying information for each part.
Doosan e80 compact excavator parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various components of an engine, including the cylinder block, gear housing, flywheel housing, oil pan, cylinder head, suction manifold, exhaust manifold, camshaft, crankshaft, pistons, and lubrication oil system. It lists part numbers, descriptions, quantities, and other identifying information for each numbered part in the diagrams.
Doosan e63 compact excavator parts catalogue manualfjjskekdm
This document provides a parts list and descriptions for various components of an engine, including:
- The cylinder block assembly and related plugs and bolts.
- The gear housing, oil pump, seals, bolts, and covers.
- The flywheel housing, oil pan, seals, and bolts.
- The cylinder head, valves, springs, seals, bolts, and related components.
- The intake manifold, sensors, bolts, and throttle body.
- The exhaust manifold and pipes, sensors, bolts, EGR components, and heat exchanger.
- The DPF muffler, sensors, pipes, bolts, and mounting components.
Doosan e55 w compact excavator parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various engine components including the cylinder block, gear housing, flywheel housing, cylinder head, intake manifold, exhaust manifold, cam shaft, crank shaft, piston, lubrication oil system, and cooling water system. It includes over 75 individual parts with descriptions and quantities for each component.
Doosan dl420 a wheeled loader parts catalogue manualfjjskekdm
This document contains parts lists and diagrams for various components of a diesel engine. It includes lists of parts, part numbers, descriptions and quantities for items like the cylinder block, timing gear case, flywheel housing, driving system, cylinder head, cylinder head cover, and timing system. Serial numbers are provided for some replaceable parts.
Doosan dl200 tc wheeled loader parts catalogue manualfjjskekdm
This document provides a parts list and diagrams for the cylinder head and related components of a diesel engine. It includes images and lists of parts with descriptions, part numbers, quantities, serial numbers and replacement part information. The list contains over 75 individual part items or assemblies that make up the cylinder head, valves, springs, guides, cover, gaskets and related hardware.
This document provides specifications, maintenance schedules, and adjustment procedures for a service manual. It includes electrical specifications and speeds, hydraulic specifications, torque specifications, lubrication charts, and planned maintenance schedules. It also provides instructions for adjusting components like the brake, brake interlock switch, steering, lift chains, speed limiting switch, and SCR card trimpots.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjjskekdm
This document provides instructions for removing and installing steering clutches on a D5C III track-type tractor. Key steps include draining oil from the steering clutch compartment, removing components like the battery and control valve, and taking apart the clutch assembly by removing items such as the cylinder, piston, springs, and drums. Reassembly requires reinstalling these components in reverse order and making adjustments to ensure proper clearance and operation.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjjskekdm
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 6zl) serv...fjjskekdm
The document provides instructions for removing and installing the transmission oil pump and pump drive gear on a D5C III track-type tractor. Key steps include draining the transmission oil, removing the tube assembly, plate, and transmission oil pump. The pump drive gear is then removed from the transmission case. Reinstallation involves reversing these steps, ensuring proper positioning of seals and connections of hoses and rods.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 5hs) serv...fjjskekdm
This document provides instructions for removing and installing final drives on Caterpillar D5C III track-type tractors. It outlines 15 steps to remove the final drive, which include draining fluid, removing guards, bolts and sprocket segments. It then describes 21 steps to install the final drive, including applying sealant, installing sprocket segments and filling with oil. The document also describes 33 steps to disassemble the final drive into additional components like bearings, seals, gears and housings.
Caterpillar cat 966 h wheel loader (prefix tal) service repair manual (tal000...fjjskekdm
This document provides instructions for disassembling and assembling the freewheel stator component of a 966H wheel loader torque converter. It contains 34 steps for disassembly, removing components like bolts, seals, gears and bearings. The 19 assembly steps list installing these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools required include link brackets, drivers, and retaining ring pliers.
Caterpillar cat 966 h wheel loader (prefix ryf) service repair manual (ryf000...fjjskekdm
This service repair manual provides instructions for disassembling and assembling the power train of Caterpillar 966H and 972H wheel loaders. It describes removing the torque converter, transmission, and transfer gears from the vehicle. It then provides step-by-step instructions for disassembling the individual components of the torque converter, including removing gears, seals, shafts, housings, and other internal parts. Safety notices are included to warn technicians to contain fluids and release pressures before conducting repairs.
Caterpillar cat 966 h wheel loader (prefix bj6) service repair manual (bj6000...fjjskekdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting tools before removing bolts and the flywheel.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and ensuring proper alignment of gears. Tools and torque specifications are also provided.
Caterpillar cat 962 k wheel loader (prefix x4t) service repair manual (x4t000...fjjskekdm
This document provides instructions for disassembling and assembling the piston pump of the steering system on a Caterpillar 962K wheel loader. The disassembly procedure outlines 28 steps to remove components like bolts, valves, spools, springs, and bearings. The assembly procedure describes 34 steps and cautions to install these components in reverse order while following safety precautions for parts under spring tension. Tolerances are provided for adjusting axial shaft end play during assembly.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjjskekdm
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before working on hydraulic systems.
Caterpillar cat 962 k wheel loader (prefix fll) service repair manual (fll000...fjjskekdm
This document provides instructions for disassembling and assembling the piston pump of the steering system on a 962K wheel loader. The disassembly procedure involves removing 28 individual parts in sequential order, including spools, plugs, springs, and bearings. The assembly procedure instructs assembling the piston pump in the reverse order and notes safety precautions for parts under spring tension.
Caterpillar cat 320 l track type excavator (prefix 9kk) service repair manual...fjjskekdm
The document provides instructions for installing a crankshaft rear seal on a 320L excavator model. It describes using a seal installer tool and locator bolt to push the new wear sleeve with seal onto the crankshaft. It also describes installing a flywheel housing by cleaning surfaces, installing a new gasket and bolts, and installing an oil seal with another tool. Finally, it describes removing and installing a crankshaft pulley by using puller and installer tools and cleaning/lubricating mating parts of a new crankshaft front seal.
Caterpillar cat 320 l track type excavator (prefix 7wk) service repair manual...fjjskekdm
This document provides instructions for installing and removing various engine components on Caterpillar 320 and 320L track-type excavators powered by a 3116 engine. It describes how to install the crankshaft rear seal carrier using specific tools and sealants. It also provides directions for removing and installing the flywheel housing, vibration damper and pulley. Technicians are advised to keep components clean and contain fluids during repair work.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Caterpillar cat th414 c gc, th417c gc telehandler operator and maintenance manual sn nmm00150 & after
1. Operation &
Maintenance Manual
Original Instructions
Keep this manual with machine at all times.
Models
TH414C GC
TH417C GC
S/N KRF00150 & After
S/N LYN00150 & After
S/N NAB00150 & After
S/N NMM00150 & After
31200957
Revised
October 1, 2014
2. Table of Contents
i31200957
TABLE OF CONTENTS
Revision Log
Read This First
Operator Qualifications ........................................................................... b
Modifications............................................................................................... b
Other Publications Available ................................................................. d
Table of Contents
Section 1 - General Safety Practices
1.1 Hazard Classification System ....................................................................1-1
Safety Alert System and Safety Signal Words...............................1-1
1.2 General Precautions .....................................................................................1-1
1.3 Operation Safety............................................................................................1-2
Electrical Hazards....................................................................................1-2
Tip Over Hazard.......................................................................................1-3
Travel Hazard............................................................................................1-6
Load Falling Hazard ...............................................................................1-7
Lifting Personnel.....................................................................................1-8
Driving Hazards on Slopes...................................................................1-9
Pinch Points and Crush Hazards.....................................................1-10
Fall Hazard..............................................................................................1-12
Chemical Hazards ................................................................................1-13
Section 2 - Pre-Operation and Inspection
2.1 Pre-Operation Check and Inspection.....................................................2-1
2.2 Safety Decals...................................................................................................2-3
2.3 Walk-Around Inspection.............................................................................2-6
2.4 Warm-Up and Operational Checks .........................................................2-8
Warm-Up Check ......................................................................................2-8
Operational Check..................................................................................2-8
2.5 Operator Cab...................................................................................................2-9
2.6 Windows........................................................................................................2-10
Cab Door Window ...............................................................................2-10
Rear Window .........................................................................................2-11
Section 3 - Controls and Indicators
3.1 General..............................................................................................................3-1
3.2 Controls.............................................................................................................3-2
Instrument Cluster..................................................................................3-4
Ignition .......................................................................................................3-6
Park Brake..................................................................................................3-7
Parking Procedure..................................................................................3-7
Transmission Control Lever (if equipped)......................................3-8
Table of Contents
3. Table of Contents
ii 31200957
Load Stability Indicator - LSI............................................................ 3-10
Steering Column Adjuster................................................................ 3-12
Joystick.................................................................................................... 3-14
Console Switches................................................................................. 3-20
Accessory Control Lever.................................................................... 3-22
3.3 Anti Theft ...................................................................................................... 3-23
3.4 Steer Modes ................................................................................................. 3-24
Manual Steering Alignment Mode Change............................... 3-24
3.5 Operator Seat .............................................................................................. 3-25
Operator Presence .............................................................................. 3-25
Adjustments.......................................................................................... 3-26
Seat Belt .................................................................................................. 3-27
3.6 Boom Indicators ......................................................................................... 3-28
Boom Extension................................................................................... 3-28
Section 4 - Operation
4.1 Engine ...............................................................................................................4-1
Starting the Engine................................................................................4-1
Battery Boosted Starting......................................................................4-2
Normal Engine Operation ...................................................................4-3
Shut-Down Procedure..........................................................................4-3
4.2 Operating with a Non-Suspended Load...............................................4-4
Lift Load Safely ........................................................................................4-4
Picking Up a Load...................................................................................4-4
Transporting a Load ..............................................................................4-5
Leveling Procedure................................................................................4-5
Placing a Load..........................................................................................4-6
Disengaging a Load...............................................................................4-6
4.3 Operating with a Suspended Load.........................................................4-7
Lift Load Safely ........................................................................................4-7
Picking Up a Suspended Load ...........................................................4-7
Transporting a Suspended Load.......................................................4-8
Leveling Procedure................................................................................4-8
Placing a Suspended Load..................................................................4-9
Disengaging a Suspended Load.......................................................4-9
4.4 Road Operation (CE).................................................................................. 4-10
4.5 Loading and Securing for Transport................................................... 4-11
Tiedown .................................................................................................. 4-11
Lifting....................................................................................................... 4-12
5. Table of Contents
iv 31200957
7.4 Lubrication Schedules.................................................................................7-8
TH414C GC................................................................................................7-8
TH417C GC................................................................................................7-9
7.5 Operator Maintenance Instructions.................................................... 7-10
Fuel System............................................................................................ 7-10
Tires .......................................................................................................... 7-12
Engine Oil............................................................................................... 7-14
Engine Cooling System ..................................................................... 7-15
Hydraulic Oil.......................................................................................... 7-16
Transmission Oil................................................................................... 7-17
Air Intake System................................................................................. 7-18
Cab Air Filters (if equipped)............................................................. 7-20
Battery ..................................................................................................... 7-22
Windshield Washer System (if equipped)................................... 7-23
Section 8 - Additional Checks
8.1 General..............................................................................................................8-1
8.2 Load Stability Indicator System ...............................................................8-1
8.3 Boom Interlock...............................................................................................8-2
Section 9 - Specifications
9.1 Product Specifications.................................................................................9-1
Fluids...........................................................................................................9-1
Capacities ..................................................................................................9-3
Tires .............................................................................................................9-4
Performance.............................................................................................9-5
Dimensions...............................................................................................9-6
Declaration of Vibration.......................................................................9-8
Noise Emission Level (CE)....................................................................9-8
Machine Towing Capacity...................................................................9-8
Index
Inspection, Maintenance and Repair Log
Transfer Of Ownership
6. Section 1 - General Safety Practices
1-131200957
SECTION 1 - GENERAL SAFETY PRACTICES
1.1 HAZARD CLASSIFICATION SYSTEM
Safety Alert System and Safety Signal Words
DANGER indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION indicates a potentiality hazardous situation which, if not avoided, may result in
minor or moderate injury.
1.2 GENERAL PRECAUTIONS
WARNING
Before operation, read & understand this manual. Failure to comply with the safety
precautions listed in this manual could result in machine damage, property damage,
personal injury or death.
DANGER OW0010
WARNING OW0021
CAUTION OW0031
7. Section 1 - General Safety Practices
1-2 31200957
1.3 OPERATION SAFETY
Note: The manufacturer has no direct control over machine application and operation.
Therefore, safety issues listed in this manual are non-exhaustive. The user and operator are
responsible for conforming with good safety practices.
Electrical Hazards
• This machine is not insulated and does not provide protection from contact or being
near electrical current.
• NEVER operate the telehandler in an area where overhead power lines, overhead or
underground cables, or other power sources may exist without ensuring the
appropriate power or utility company de-energizes the lines.
• Always check for power lines before raising the boom.
• Follow employer, local and governmental regulations for clearance from powerlines.
OW0040
10 FT
(3 M)
8. Section 1 - General Safety Practices
1-331200957
Tip Over Hazard
General
• For additional load requirements, refer to the appropriate capacity chart.
• Never use an attachment without the appropriate JLG approved capacity chart
installed on the telehandler.
• Understand how to properly use the capacity charts located in cab.
• DO NOT exceed rated lift capacity.
• Be sure that the ground conditions are able to support the machine.
• DO NOT raise boom unless frame is level (0 degrees), unless otherwise noted on
capacity chart.
• DO NOT level machine with boom/attachment above 1,2 m (4 ft).
(AUS - DO NOT level machine with load more than 300 mm (11.8 in) above ground
surface.)
OW0050
OW0080
OW0100
4 FT
(1,2 M)
9. Section 1 - General Safety Practices
1-4 31200957
• MAINTAIN proper tire pressure at all times. If proper tire pressures are not
maintained, this machine could tip over.
• Refer to manufacturer’s specifications for proper fill ratio and pressure requirements
for tires equipped with ballast.
• Always wear the seat belt.
• Keep head, arms, hands, legs and all other body parts inside operator’s cab at all times.
If the telehandler starts to tip over:
• DO NOT JUMP
• BRACE YOURSELF and STAY WITH THE MACHINE
• KEEP YOUR SEAT BELT FASTENED
• HOLD ON FIRMLY
• LEAN AWAY FROM THE POINT OF IMPACT
OH2291
OH20911
OH2221
10. Section 1 - General Safety Practices
1-531200957
Non-Suspended Load
• DO NOT drive with boom raised.
Suspended Load
• Tether suspended loads to restrict movement.
• Weight of all rigging (slings, etc.) must be included as part of load.
• Beware of wind. Wind can cause a suspended load to swing and cause dangerous side
loads - even with tag lines.
• DO NOT attempt to use telehandler frame-leveling to compensate for load swing.
• Keep heavy part of load closest to attachment.
• Never drag the load; lift vertically.
When driving with a suspended load:
• Start, travel, turn and stop slowly to prevent load from swinging.
• DO NOT extend boom.
• DO NOT raise the load more than 300 mm (11.8 in) above ground surface or the
boom more than 45°.
• DO NOT exceed walking speed.
OW0060
OW0150
11. Section 1 - General Safety Practices
1-6 31200957
Travel Hazard
• Steering characteristics differ between steer modes. Identify the steer mode settings
of the telehandler being operated.
• DO NOT change steer modes while traveling. Steer modes must be changed while
telehandler is stationary.
• Visually verify proper wheel alignment after each steer mode change.
• Ensure that adequate clearance is provided for both rear tail swing and front fork
swing.
• Look out for and avoid other personnel, machinery and vehicles in the area. Use a
spotter if you DO NOT have a clear view.
• Before moving be sure of a clear path and sound horn.
• When driving, retract boom and keep boom/attachment as low as possible while
maintaining visibility of mirrors and maximum visibility of path of travel.
• Always look in the direction of travel.
• Always check boom clearances carefully before driving underneath overhead
obstructions. Position attachment/load to clear obstacles.
• When driving in high speed, use only front wheel steer (if steering modes are
selectable).
• Telehandlers equipped with solid tires should not be used in applications requiring
excessive roading or driving extended distances. In the event an application requires
excessive roading or driving expanded distances, it is recommended to use
telehandlers not equipped with solid tires.
OAL2030
2-Wheel Front Steer 4-Wheel Circle Steer 4-Wheel Crab Steer
12. Section 1 - General Safety Practices
1-731200957
Load Falling Hazard
• Never suspend load from forks or other parts of carriage weldment. Use only JLG
approved lift points.
• DO NOT burn or drill holes in fork(s).
• Forks must be centered under load and spaced apart as far as possible.
OW0130
13. Section 1 - General Safety Practices
1-8 31200957
Lifting Personnel
• When lifting personnel, USE ONLY an approved personnel work platform, with proper
capacity chart displayed in the cab.
• DO NOT drive machine from cab when personnel are in platform.
OW0170
OW0190
14. Section 1 - General Safety Practices
1-931200957
Driving Hazards on Slopes
To maintain sufficient traction and braking capabilities, travel on slopes as follows:
• When unloaded, drive with forks pointed downhill.
• When loaded, drive with the forks pointed uphill.
• For additional travel requirements, refer to the appropriate capacity chart.
• To avoid overspeeding the engine and drivetrain when driving down slopes,
downshift to a lower gear and use the service brake as necessary to maintain a slow
speed. DO NOT shift into neutral and coast downhill.
• Avoid excessively steep slopes or unstable surfaces. To avoid tip over DO NOT drive
across excessively steep slopes under any circumstances.
• Avoid turning on a slope. Never engage “inching” or shift to “Neutral” when going
downhill.
• DO NOT park on a slope.
OW0200
15. Section 1 - General Safety Practices
1-10 31200957
Pinch Points and Crush Hazards
Stay clear of pinch points and rotating parts on the telehandler.
• Stay clear of moving parts while engine is running.
• Keep clear of steering tires and frame or other objects.
• Keep clear from under boom.
OW0210
OW0220
OW0230
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Section 1 - General Safety Practices
1-1131200957
• Keep clear of boom holes.
• Keep arms and hands clear of attachment tilt cylinder.
• Keep hands and fingers clear of carriage and forks.
• Keep others away while operating.
OW0240
OW0250
OW0260
OW0960
18. Section 1 - General Safety Practices
1-12 31200957
Fall Hazard
• Enter using the proper hand holds and steps provided. Always maintain 3-point
contact when mounting or dismounting. Never grab control levers or steering wheel
when mounting or dismounting the machine.
• DO NOT get off the machine until the shutdown procedure on page 4-3 has been
performed.
• DO NOT carry riders. Riders could fall off machine causing death or serious injury.
OW0280
OW0290