This document provides assembly instructions for rear axles on an excavator model M322C. It details 27 steps to assemble bearings and seals in the hub and install the hub on the spindle. Several tools are required, including torque wrenches, seal installers, and pullers. Proper bearing temperatures and torque specifications must be followed to ensure correct assembly.
Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (...udjfjkskekmdm
This document provides assembly instructions for rear axles on an excavator model M322C. It details 27 steps to assemble bearings and seals in the hub and install the hub on the spindle. Several tools are required, including torque wrenches, seal installers, and pullers. Proper bearing temperatures and torque specifications must be followed to ensure correct assembly.
Caterpillar cat m313 d wheeled excavator (prefix j3a) service repair manual (...udfjjdjkskkemmd
This document provides assembly instructions for the transmission of a M313D Wheeled Excavator. It lists over 60 steps and required tools to assemble the transmission components in the proper order. This includes installing bearings, seals, gears, shafts, and other internal parts. Dimensions are also specified to set proper clearances and preloads during assembly. Tools such as retaining ring pliers, drivers, torque wrenches, and seals installers are required. Illustrations accompany each step to show the assembly process.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for disassembling and assembling the front axle components of an M318C Wheeled Excavator, including:
1. Removing components like the carrier housing, planetary gears, brake discs, and hub assembly which involve using various tools and lifting devices.
2. Disassembling internal components of the carrier like retaining rings, bearings, and seals.
3. Cleaning all parts before assembly and heating/cooling some components to aid installation.
4. Reassembling the components in reverse order, applying grease and torquing fasteners to specifications. Proper cleanliness and procedure is emphasized for the precision components.
Caterpillar cat 962 h wheel loader (prefix m3g) service repair manual (m3g000...udjjjsjekkdm
This document provides instructions for disassembling and assembling the piston pump of a 962H wheel loader. It gives detailed steps for disassembling components like valves, spools, plugs, springs, and bearings. It then describes the assembly process in reverse order, noting things like applying the correct torque to bolts and checking axial shaft end play. The overall document provides a technical service manual for maintenance and repair work on the loader's steering pump.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...yhhjjkfkseme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Caterpillar cat 950 h wheel loader (prefix n1a) service repair manual (n1a000...dikdkskmmdm
The document provides instructions for disassembling and assembling the steering pump on a Caterpillar 950H wheel loader. It lists 28 steps for disassembly, including removing bolts, valves, springs, and other internal pump components. 34 steps are provided for assembly, instructing technicians to install components in reverse order and noting that cleanliness is important. A final check of axial shaft end play is specified to ensure proper clearance.
Caterpillar cat m322 d wheeled excavator (prefix p2t) service repair manual (...udfjjdjkksmmd
This document provides assembly instructions for a piston pump used in a wheeled excavator. It describes 49 assembly steps, requiring various tools. Key steps include installing bearings and seals, assembling the rotating assembly, installing pistons and adjusting lift-off clearance using shims. The correctly assembled pump is then ready to be installed in the excavator.
Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (...udjfjkskekmdm
This document provides assembly instructions for rear axles on an excavator model M322C. It details 27 steps to assemble bearings and seals in the hub and install the hub on the spindle. Several tools are required, including torque wrenches, seal installers, and pullers. Proper bearing temperatures and torque specifications must be followed to ensure correct assembly.
Caterpillar cat m313 d wheeled excavator (prefix j3a) service repair manual (...udfjjdjkskkemmd
This document provides assembly instructions for the transmission of a M313D Wheeled Excavator. It lists over 60 steps and required tools to assemble the transmission components in the proper order. This includes installing bearings, seals, gears, shafts, and other internal parts. Dimensions are also specified to set proper clearances and preloads during assembly. Tools such as retaining ring pliers, drivers, torque wrenches, and seals installers are required. Illustrations accompany each step to show the assembly process.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for disassembling and assembling the front axle components of an M318C Wheeled Excavator, including:
1. Removing components like the carrier housing, planetary gears, brake discs, and hub assembly which involve using various tools and lifting devices.
2. Disassembling internal components of the carrier like retaining rings, bearings, and seals.
3. Cleaning all parts before assembly and heating/cooling some components to aid installation.
4. Reassembling the components in reverse order, applying grease and torquing fasteners to specifications. Proper cleanliness and procedure is emphasized for the precision components.
Caterpillar cat 962 h wheel loader (prefix m3g) service repair manual (m3g000...udjjjsjekkdm
This document provides instructions for disassembling and assembling the piston pump of a 962H wheel loader. It gives detailed steps for disassembling components like valves, spools, plugs, springs, and bearings. It then describes the assembly process in reverse order, noting things like applying the correct torque to bolts and checking axial shaft end play. The overall document provides a technical service manual for maintenance and repair work on the loader's steering pump.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...yhhjjkfkseme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Caterpillar cat 950 h wheel loader (prefix n1a) service repair manual (n1a000...dikdkskmmdm
The document provides instructions for disassembling and assembling the steering pump on a Caterpillar 950H wheel loader. It lists 28 steps for disassembly, including removing bolts, valves, springs, and other internal pump components. 34 steps are provided for assembly, instructing technicians to install components in reverse order and noting that cleanliness is important. A final check of axial shaft end play is specified to ensure proper clearance.
Caterpillar cat m322 d wheeled excavator (prefix p2t) service repair manual (...udfjjdjkksmmd
This document provides assembly instructions for a piston pump used in a wheeled excavator. It describes 49 assembly steps, requiring various tools. Key steps include installing bearings and seals, assembling the rotating assembly, installing pistons and adjusting lift-off clearance using shims. The correctly assembled pump is then ready to be installed in the excavator.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjseazqkkdmmem
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The instructions include 27 steps for assembling the front axle and 18 steps for the rear. Key steps include pressing in seals, installing bearings and retaining rings at specified temperatures, measuring brake disc clearance, and torquing nuts to the specified values. Tools and safety precautions are also listed.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjjsekkmdmes
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The instructions include 27 steps for assembling the front axle and 18 steps for the rear. Key steps include pressing in seals, installing bearings and retaining rings at specified temperatures, measuring brake disc clearance, and torquing nuts to the specified values. Tools and safety precautions are also listed.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjksekmdme
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of an M318F Wheeled Excavator. The instructions include 27 steps for assembling the front axle and 10 steps for assembling the rear axle. Tools and safety precautions are listed. Dimensions must be measured and verified during assembly to ensure correct clearance between parts.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjsekdemmd
The document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The assembly process involves 27 steps for the front axle and 18 steps for the rear axle. Key steps include installing bearings and seals, installing and adjusting brake components to achieve the specified clearance, and torquing nuts to the specified values. The assembly is completed by filling the front final drives with oil and installing the front tires and rims.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...udfjjdjkkmds
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of an M318F Wheeled Excavator. The instructions include 27 steps for assembling the front axle and 10 steps for assembling the rear axle. Various tools are required, and technicians must take care with springs and ensure proper torque specifications and clearances are achieved.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fusjjefjskekemm
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of an M318F Wheeled Excavator. The instructions include 27 steps for assembling the front axle and 10 steps for assembling the rear axle. Various tools are required, and technicians must take care when working with springs and installing bearings and seals. Dimensions are measured and specifications checked to ensure correct clearance between components.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjsjjefskekkme
The document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The instructions include 27 steps for assembling the front axle and 18 steps for assembling the rear axle. Various parts are installed and tightened to specified torques, including bearings, seals, gears, discs, housings, and nuts. Clearances are checked and adjusted as needed during assembly.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It involves 24 steps to disassemble the various components of the torque converter using various tools. The assembly procedure also involves 24 steps and specifies the proper order and method to install each component back onto the torque converter using the appropriate tools. Precautions are provided to keep parts clean and apply locking agents as needed.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It describes in detail each step of the process, including removing 24 individual parts and reinstalling them in the reverse order. Special tools are required for tasks like separating components and installing bearings. Proper cleaning and lubrication of parts is important to prevent wear.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It describes in detail each step of disassembly, including removing 24 individual parts like bolts, bearings, and seals. The assembly section then lists 25 steps for reassembling the torque converter and installing each part in reverse order. Tools required include link brackets, a transmission repair stand, drivers, pullers, and retaining ring pliers.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It describes in detail each step of disassembly, including removing 24 individual parts like bolts, bearings, and seals. The assembly section then lists 25 steps to reassemble the torque converter in reverse order, noting requirements like heating or cooling parts and applying threadlock. Tools required include link brackets, a transmission repair stand, drivers, pullers, and retaining ring pliers.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, races, and gears in the specified order while following torque specifications.
2. Install the stator, carrier assembly, impeller, and drive flange. Fit the idler gear, shaft assembly, and pump drive gear into the torque converter housing.
3. Attach the pump adapter and check bearing end play using gauges before applying the final seal.
This document provides instructions for disassembling and assembling the torque converter of a 627G Wheel Scraper. The disassembly process involves using various tools to remove over 30 individual components in a specific sequence. The assembly section then lists the reverse steps, providing guidance on cleaning parts and installing components in the correct order while maintaining proper temperatures and torques.
John deere 230 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualfhsjejkdm
This technical manual provides specifications and information for servicing a John Deere 200 Sprayer Attachment. It includes sections on general specifications for the vehicle and sprayer components, repair information such as torque values, lubricant specifications, and locations for identification numbers. It also describes operational checkout procedures to test the sprayer system.
John deere 113 172 clipper service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, including engine details, fuel and oil requirements, ignition components, and dimensions for the different models. Safety guidelines are also outlined for operating the equipment safely.
John deere 110 g, 210g, 240g 260g trimmer clutters service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreach and kickback, and not modify machines without authorization.
John deere 54 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
More Related Content
Similar to Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy00001 02000)
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjseazqkkdmmem
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The instructions include 27 steps for assembling the front axle and 18 steps for the rear. Key steps include pressing in seals, installing bearings and retaining rings at specified temperatures, measuring brake disc clearance, and torquing nuts to the specified values. Tools and safety precautions are also listed.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjjsekkmdmes
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The instructions include 27 steps for assembling the front axle and 18 steps for the rear. Key steps include pressing in seals, installing bearings and retaining rings at specified temperatures, measuring brake disc clearance, and torquing nuts to the specified values. Tools and safety precautions are also listed.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjksekmdme
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of an M318F Wheeled Excavator. The instructions include 27 steps for assembling the front axle and 10 steps for assembling the rear axle. Tools and safety precautions are listed. Dimensions must be measured and verified during assembly to ensure correct clearance between parts.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjsekdemmd
The document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The assembly process involves 27 steps for the front axle and 18 steps for the rear axle. Key steps include installing bearings and seals, installing and adjusting brake components to achieve the specified clearance, and torquing nuts to the specified values. The assembly is completed by filling the front final drives with oil and installing the front tires and rims.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...udfjjdjkkmds
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of an M318F Wheeled Excavator. The instructions include 27 steps for assembling the front axle and 10 steps for assembling the rear axle. Various tools are required, and technicians must take care with springs and ensure proper torque specifications and clearances are achieved.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fusjjefjskekemm
This document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of an M318F Wheeled Excavator. The instructions include 27 steps for assembling the front axle and 10 steps for assembling the rear axle. Various tools are required, and technicians must take care when working with springs and installing bearings and seals. Dimensions are measured and specifications checked to ensure correct clearance between components.
Caterpillar cat m318 f wheeled excavator (prefix f8b) service repair manual (...fjsjjefskekkme
The document provides assembly instructions for final drive carriers, hubs, and brakes on the front and rear axles of a M318F wheeled excavator. The instructions include 27 steps for assembling the front axle and 18 steps for assembling the rear axle. Various parts are installed and tightened to specified torques, including bearings, seals, gears, discs, housings, and nuts. Clearances are checked and adjusted as needed during assembly.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It involves 24 steps to disassemble the various components of the torque converter using various tools. The assembly procedure also involves 24 steps and specifies the proper order and method to install each component back onto the torque converter using the appropriate tools. Precautions are provided to keep parts clean and apply locking agents as needed.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It describes in detail each step of the process, including removing 24 individual parts and reinstalling them in the reverse order. Special tools are required for tasks like separating components and installing bearings. Proper cleaning and lubrication of parts is important to prevent wear.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It describes in detail each step of disassembly, including removing 24 individual parts like bolts, bearings, and seals. The assembly section then lists 25 steps for reassembling the torque converter and installing each part in reverse order. Tools required include link brackets, a transmission repair stand, drivers, pullers, and retaining ring pliers.
This document provides instructions for disassembling and assembling the torque converter of a 631K Wheel Tractor. It describes in detail each step of disassembly, including removing 24 individual parts like bolts, bearings, and seals. The assembly section then lists 25 steps to reassemble the torque converter in reverse order, noting requirements like heating or cooling parts and applying threadlock. Tools required include link brackets, a transmission repair stand, drivers, pullers, and retaining ring pliers.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, races, and gears in the specified order while following torque specifications.
2. Install the stator, carrier assembly, impeller, and drive flange. Fit the idler gear, shaft assembly, and pump drive gear into the torque converter housing.
3. Attach the pump adapter and check bearing end play using gauges before applying the final seal.
This document provides instructions for disassembling and assembling the torque converter of a 627G Wheel Scraper. The disassembly process involves using various tools to remove over 30 individual components in a specific sequence. The assembly section then lists the reverse steps, providing guidance on cleaning parts and installing components in the correct order while maintaining proper temperatures and torques.
Similar to Caterpillar cat m322 c wheeled excavator (prefix bdy) service repair manual (bdy00001 02000) (13)
John deere 230 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualfhsjejkdm
This technical manual provides specifications and information for servicing a John Deere 200 Sprayer Attachment. It includes sections on general specifications for the vehicle and sprayer components, repair information such as torque values, lubricant specifications, and locations for identification numbers. It also describes operational checkout procedures to test the sprayer system.
John deere 113 172 clipper service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, including engine details, fuel and oil requirements, ignition components, and dimensions for the different models. Safety guidelines are also outlined for operating the equipment safely.
John deere 110 g, 210g, 240g 260g trimmer clutters service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreach and kickback, and not modify machines without authorization.
John deere 54 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 51 & 246 rotary brooms service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission oils, and specifications for rotary mowers and snowblowers. The manual aims to ensure technicians have the correct information to service equipment properly and safely.
John deere 48, 450, 550 & 660 rotary tillers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48, 50, 54, 60, 72, 76, 160, 172, 261 & 272 rotary mowers serv...fhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and operational testing for the engine, fuel system, electrical system, power train, steering, brakes, mower deck, and other components. Safety messages are presented throughout and fastener torque specifications are provided. The manual is intended for experienced technicians and is part of John Deere's total product support program.
John deere 47, 59 & 359 snowblowers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 46, 49 & 50 snowthrowers service repair manualfhsjejkdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers sections like safety procedures, fluid handling, battery handling, and service procedures.
Clark gph 50 forklift service repair manualfhsjejkdm
This document provides guidance on planned maintenance procedures for lift trucks. It emphasizes the importance of routine inspections and lubrication for long life and trouble-free operation. The summary outlines key steps in the planned maintenance process, including:
1. Performing a visual inspection of the entire lift truck, checking for issues like leaks, loose fasteners, and worn/damaged components.
2. Using a planned maintenance report form to document inspections and any needed repairs.
3. Testing functions like the starting system, gauges, controls, brakes and steering to ensure proper operation.
4. Inspecting and lubricating specific components, like the engine, hydraulic and electrical systems, wheels/
Clark gp127 e forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark lift truck maintenance personnel. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Specific safety practices include properly jacking, blocking and lifting trucks, following electrical safety procedures, and ensuring only trained personnel conduct maintenance.
Clark gp127 forklift service repair manualfhsjejkdm
This document provides instructions and safety precautions for Clark industrial lift truck maintenance personnel. It outlines recommended safe maintenance practices including properly jacking, blocking and towing trucks. The document instructs technicians to only perform maintenance if trained and authorized, using manufacturer procedures and recommendations. Technicians are advised to take safety precautions such as wearing protective equipment, disconnecting power sources, and avoiding fire hazards.
Clark gex20 30 forklift service repair manualfhsjejkdm
The document provides instructions and safety information for maintaining industrial trucks. It discusses identifying and understanding safety signs, recommended safe maintenance practices, and general shop safety precautions. The safe maintenance practices section lists 20 points covering proper maintenance procedures, qualifications of maintenance personnel, personal protective equipment, safety checks, fuel and electrical system handling, inspection of truck components, and using proper replacement parts.
Clark gcs standard forklift service repair manualfhsjejkdm
- This document is a service manual intended for CLARK dealers providing maintenance and repair information for CLARK lift trucks.
- It contains general safety practices and precautions for working on lift trucks, identifying important safety signs and messages, and provides model identification information.
- Technicians are instructed to read all safety information and follow proper procedures to prevent injuries when servicing lift trucks.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M322C WHEELED EXCAVATOR BDY
Configuration: M322C Excavator BDY00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C MH and M322C MH Excavators Power Train
Media Number -RENR7011-03 Publication Date -01/10/2006 Date Updated -25/10/2006
i06216406
Final Drive Carriers, Hubs and Brakes - Assemble - Rear
Axle
SMCS - 4054-016; 4092-016; 4253-016; 4255-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C
1P-1859 Retaining Ring Pliers 1
1P-1853 Retaining Ring Pliers 1
1U-8758 Retaining Ring Pliers 1
E
6V-6080 Torque Multiplier Gp 1
4C-4661 Center Ring 1
4C-4058 Spanner 1
F 1U-6415 Three Jaw Puller 1
H 1P-0510 Driver Gp 1
I 9S-7354 Torque Wrench Gp 1
J 9U-5006 Torque Wrench Gp 1
K 123-6707 Seal Installer 1
L 6V-7030 Micrometer Depth Gauge Group 1
M 8T-0447 Dial Caliper 1
N 188-7400 Piston Installer 1
1/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. P 123-6695 Driver 1
Q 4C-3085 Two Jaw Puller 1
R 182-1744 Bearing Puller 1
S 6V-6640 Sealant 1
T 5P-0960 Molybdenum Grease 1
U 9S-3263 Thread Lock Compound 1
V 129-1063 Rivet Tool 1
Illustration 1 g00915150
1. Install the O-ring seals on connector (40) . Install connector (40) in the spindle.
2. Install breather valve (42) in the spindle.
3. Install O-ring seal (41) in the spindle.
Note: Some spindle assemblies will have four plugs. If the plugs have been removed, use
Tooling (V) to install four new plugs in each spindle assembly.
2/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g00917225
4. Install spindle (39) in the spindle's original location.
5. Install bolts (37) . Tighten the socket head bolts to a torque of 280 N·m (210 lb ft).
6. Install slotted nut (38) .
Illustration 3 g00917226
7. Use Tooling (P) to install plate (36) on the spindle. Install the plate until the plate makes
contact with the face of the spindle.
Illustration 4 g00917229
8. Heat inner bearing cone (35) to a temperature of 135 °C (275 °F). Install inner bearing cone
(35) on the spindle. Make sure that the bearing cone is seated against the shoulder on the
spindle.
3/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00917230
9. Lower the temperature of the inner bearing cup to a temperature of -75 °C (-103 °F). Install
the inner bearing cup in hub (31) . Use Tooling (G) to seat the inner bearing cup in the hub.
Illustration 6 g00917242
10. Invert the hub. Lower the temperature of outer bearing cup (33) to a temperature of -75 °C
(-103 °F). Install the outer bearing cup in hub (31) . Use Tooling (H) to seat the outer
bearing cup in the hub.
4/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 7 g00917244
11. Install hub (31) onto the spindle.
12. Bushing (32A) is available in several thicknesses. If a new wheel bearing, a new spanner
nut, a new ring gear, or a new hub is used, the thickness of bushing (32A) must be
determined in order to obtain the correct amount of rolling torque on the hub.
13. Install bushing (32A) onto the spindle.
Illustration 8 g00917245
14. Heat outer bearing cone (32) to a temperature of 135 °C (275 °F). Install outer bearing cone
(32) on the housing for the steering axle. Make sure that the outer bearing cone is correctly
seated.
Illustration 9 g00917246
15. Install retaining ring (24) .
16. Install ring (26) into ring gear assembly (20) .
5/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 10 g00917248
Note: Slightly stretch one of the O-ring seals (29) prior to installing the seal on the larger
diameter. Heat two backup rings (30) in an oil bath prior to installing the backup rings.
17. Install backup rings (30) and O-ring seals (29) onto brake piston (25) . Install the O-ring
seals so that the oil grooves are facing each other.
Illustration 11 g00917256
18. Install Tooling (N) on brake piston (25) , as shown. Install the centering ring (part of
Tooling (N) ) on the brake piston first. The centering ring is the larger ring in Tooling (N) .
Install the installer (part of Tooling (N) ) on the brake piston. Remove the centering ring
from the brake piston.
6/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 12 g00917258
19. Use a press to carefully position brake piston (25) against the shoulder in ring gear assembly
(20) . Remove the installer (part of Tooling (H) ) from the brake piston.
Illustration 13 g00917260
20. Install the springs and bolts (22) into ring gear assembly (20) .
7/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 14 g00896103
Illustration 15 g00917261
Illustration 16 g00917262
21. Apply Tooling (U) on the threads of bolts (22) . Tighten nuts (21) until Distance (W)
between the threaded end of each socket head bolt and the contact surface of brake piston
(25) is 0.75 ± 0.25 mm (0.030 ± 0.010 inch). Use Tooling (L) to measure Distance (W) at
each socket head bolt. The maximum torque of each nut that is used on the end of socket
head bolts (22) must not exceed 11 N·m (8 lb ft).
8/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 17 g00896107
Note: Make sure that the holes for the supply oil in the spindle align with the holes for the
supply oil in the ring gear.
22. Install ring gear (21) on the housing for the steering axle assembly.
Illustration 18 g00916878
23. Install ring gear assembly (20) without the seals.
24. Apply Tooling (T) to the threads of spanner nut (19) . Install spanner nut (19) .
25. Use the following procedure to tighten spanner nut (19) :
9/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 19 g00895309
a. Install Tooling (E) and Tooling (J) onto spanner nut (19) .
b. Rotate the hub while spanner nut (19) is being torqued. Tighten the spanner nut to a
torque of 1200 N·m (885 lb ft). Do not exceed a torque of 1464 N·m (1080 lb ft).
Illustration 20 g00917263
26. Install two lug nuts on one of the wheel studs. Tighten the lug nuts against each other so that
the lug nuts cannot move. Install an appropriate socket and Tooling (K) on the lug nut.
Position Tooling (K) so that Tooling (K) is in line with the radius of the hub, as shown.
Note: Tooling (K) must be in line with the radius of the hub, as shown.
Note: The required rolling torque for the roller bearing is 15 ± 3 N·m (133 ± 27 lb in).
Note: The required rolling torque for the roller bearing must be measured from the center of
the hub. Tooling (K) is not attached to the center of the hub, but to the wheel stud. The
torque reading for Tooling (K) has been recalculated. The calculation is based on the length
of Tooling (K) . The torque reading on Tooling (K) must be 8.2 ± 1.6 N·m (73 ± 14 lb in).
This setting on Tooling (K) will obtain the required rolling torque of 15 ± 3 N·m (133 ± 27
lb in).
27. Use Tooling (K) to slowly rotate the hub. Record the amount of torque that is required to
rotate the hub. The torque reading on Tooling (K) must be 8.2 ± 1.6 N·m (73 ± 14 lb in). If
10/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. the rolling torque is not correct repeat Steps 14 through Steps 25 by using a different
bushing. If the rolling torque is greater than the value that is specified, install the next wider
bushing. If the rolling torque is less than the specified value, install the next narrower
bushing. Recheck the rolling torque.
Note: After the correct size for bushing (39) and the correct rolling torque are obtained, the
ring gear and the hub are removed in order to install the seals.
28. After the correct rolling torque of the hub is obtained, use Tooling (E) to remove spanner
nut (19) . Remove ring gear assembly (20) .
29. Remove spacer (32A) .
Illustration 21 g00917265
30. Use Tooling (F) to remove hub (31) .
31. Remove the outer bearing cone (32) . Remove bushing (32A) .
Illustration 22 g00917264
32. Fasten Tooling (R) to inner bearing cone (35) . Fasten Tooling (Q) to Tooling (R) . Remove
the inner bearing cone from the spindle.
11/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 23 g00917267
33. Heat inner bearing cone (35) to a temperature of 135 °C (275 °F). Install the inner bearing
cone in the inner bearing cup.
Illustration 24 g00917269
12/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 25 g00917272
34. Immediately apply Tooling (S) to the outer diameter of lip type seal (34) . Use Tooling (K)
to install lip type seal (34) in hub (31) . Install the seal with the sealing lip toward inner
bearing cone (37) . Tooling (K) will set the depth of the seal in the hub.
Illustration 26 g00917275
35. Install hub (31) onto spindle (39) .
13/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 27 g00917277
36. Install bushing (32A) on the spindle.
Illustration 28 g00917280
37. Heat outer bearing cone (32) to a temperature of 135 °C (275 °F). Install outer bearing cone
(32) on the housing for the steering axle. Make sure that the outer bearing cone is correctly
seated.
Illustration 29 g00917546
14/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 38. Install O-ring seal (24) and the backup ring.
Illustration 30 g00896107
Note: Make sure that the holes for the supply oil in the spindle align with the holes for the
supply oil in the ring gear.
39. Apply clean hydraulic oil on the O-ring seal that is on the hub. Install ring gear assembly
(20) on the hub. Make sure that the O-ring seal that is on the hub is not damaged.
Illustration 31 g00916878
Note: Install spanner nut (19) on the spindle without O-ring seal (24) nor spacer (32A) .
Tighten the spanner nut by hand so that the O-ring seal and the spacer can be installed on
the spindle. Remove the spanner nut.
40. Apply Tooling (T) to the threads of spanner nut (19) . Install O-ring seal (22) , spacer (23)
and spanner nut (19) on the threaded portion of the spindle.
41. Use the following procedure to tighten spanner nut (19) :
15/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 32 g00895309
a. Install Tooling (E) and Tooling (J) onto spanner nut (19) .
b. Rotate the hub while spanner nut (19) is being torqued. Tighten the spanner nut to a
torque of 1200 N·m (885 lb ft). Do not exceed a torque of 1464 N·m (1080 lb ft).
Illustration 33 g00914485
42. Install lockring (18) . Make sure that the tab on lockring (18) engages with a slot in spanner
nut (19) , as shown.
16/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 34 g00917282
43. Use Tooling (C) to temporarily install retaining ring (14) in ring gear (20) . Use Tooling
(M) to measure the distance from the internal face of ring gear assembly (20) to the face of
brake piston (25) . Subtract the thickness of the bar stock. Record this dimension as
Dimension (X) .
Illustration 35 g00917283
44. Use Tooling (M) to measure the distance from the inside face of retaining ring (15) to the
outside face of ring gear assembly (20) . Record this dimension as Dimension (Y) .
45. Subtract Dimension (Y) from Dimension (X) . Record this dimension as Dimension (Z) .
46. Use Tooling (C) in order to remove retaining ring (15) .
Illustration 36 g00917285
47. Use Tooling (M) to measure the thickness of thrust washer (14) . Record this dimension as
Dimension (Q) .
17/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 37 g00917286
48. Use Tooling (M) in order to measure the thickness of plate (16) . There are four outer plates.
Find the total thickness of the four outer plate. Record this dimension as Dimension (R) .
Illustration 38 g00917288
49. Use Tooling (M) in order to measure the thickness of each plate (17) . There are three inner
discs. Find the total thickness of the three inner discs. Record this dimension as Dimension
(S) .
50. Determine the thickness of the outer discs, the inner discs and the thrust washer. Record this
dimension as dimension (T) .
(Q) + (R) + (S) = (T)
51. Determine the piston stroke by subtracting Dimension (T) from Dimension (Z) .
Note: The piston stroke must be 2.6 ± 0.2 mm (0.10 ± 0.01 inch).
Note: Plates are available in various thicknesses.
Note: Install the thinner plates to the outside of the pack.
18/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 39 g00917290
52. Install axle shaft (13) . Make sure that the axle shaft engages with the rear differential.
Illustration 40 g00917291
53. Install gear (10) into ring gear assembly (20) .
Illustration 41 g00917294
19/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 54. Install four discs (17) and three plates (16) into ring gear assembly (20) . Install the discs in
alternating order. Start and end with a plate.
55. Install thrust washer (14) into ring gear assembly (20) .
Illustration 42 g00917295
Illustration 43 g00914480
56. Use Tooling (C) in order to install retaining ring (15) into ring gear assembly (20) .
57. Install gear (9) into sun gear (10) .
20/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 44 g00896127
58. Install roller bearing (7) in each of planetary gear (5) . Install the washer and retaining ring
(8) on both sides of roller bearing (7) .
Illustration 45 g00896128
59. Heat planetary gears (5) to temperature of 135 °C (275 °F).
60. Install planetary gears (5) into carrier housing (2) .
21/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 46 g00896129
61. Use Tooling (C) in order to install retaining ring (4) .
62. Use the following procedure in order to adjust the end play of sun gear (9) :
Illustration 47 g00896130
a. Use Tooling (L) to measure the distance from the mating surface of the planetary
carrier to the bottom of the counterbore for the thrust washer. Subtract the thickness
of the bar stock. Record this dimension as Dimension (H) .
Illustration 48 g00896131
b. Push in on sun gear (9) . Use Tooling (L) to measure the distance from the end of the
sun gear to the mating surface on the hub, as shown. Subtract the thickness of the bar
stock. Record this dimension as Dimension (J) .
c. Subtract Dimension (J) from Dimension (H) . Record this dimension as Dimension
(K) . Subtract the desired end play of 0.50 ± 0.10 mm (0.020 ± 0.004 inch) from
dimension (K) in order to determine the correct thickness of thrust washer (6) .
22/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 49 g00896702
d. Select the appropriate thickness of thrust washer (6) that is determined in Step 62.a
through Step 62.c. Install the thrust washer in the planetary carrier, as shown.
Illustration 50 g00917297
Note: Engaging the planetary gears in carrier housing (2) with the ring gear may be difficult
during the installation of the planetary carrier.
63. Fasten an suitable lifting device to the lifting sling. Place the planetary carrier in the
planetary carrier's original location on the wheel studs in the hub. Temporarily install four
lug nuts. Install the lug nuts in 90 degree intervals. The planetary gears in the planetary
carrier will not be engaged with ring gear (20) at this time. Slowly rotate the hub on the
opposite side of the axle. Tighten each lug nut slightly. Continue to tighten each lug nut
slightly. The force of the lug nuts against the planetary carrier and the slow rotation of the
hub will cause the planetary gears in the planetary carrier to engage with the ring gear. After
the planetary carrier is correctly installed, remove the four lug nuts.
64. Install bolts (1) .
23/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 51 g00915273
65. Connect hose assembly (3) .
End By: Install the tire and rim (rear). Refer to Disassembly and Assembly, "Tire and Rim Install
(Rear)".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 27 07:33:29 UTC+0800 2020
24/24(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M322C WHEELED EXCAVATOR BDY
Configuration: M322C Excavator BDY00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C MH and M322C MH Excavators Power Train
Media Number -RENR7011-03 Publication Date -01/10/2006 Date Updated -25/10/2006
i04706203
Final Drive Carriers, Hubs and Brakes - Assemble - Front
Axle
SMCS - 4054-016; 4092-016; 4253-016; 4255-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Gp 1
C 1P-1859 Retaining Ring Pliers 1
E
6V-6080 Torque Multiplier Gp 1
4C-6061 Center Ring 1
4C-4058 Spanner 1
F 1U-6415 Three Jaw Puller 1
H 1P-1853 Retaining Ring Pliers 1
J 1U-8758 Retaining Ring Pliers 1
K 123-6707 Seal Installer 1
L 6V-7030 Micrometer Depth Gauge Group 1
M 8T-0447 Dial Caliper 1
N 188-7400 Piston Installer 1
P 1P-0808 Multipurpose Grease 1
R 9S-7354 Torque Wrench Gp 1
1/19(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. S 9U-5006 Torque Wrench 1
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Illustration 1 g00895163
1. Raise the temperature of inner bearing cone (39).
2. Install inner bearing cone (39) onto spindle (33).
Illustration 2 g01138419
2/19(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 3 g00895164
3. Lower the temperature of bearing cup (35) and (36).
4. Use Tooling (B) in order to install bearing cup (36) and (35).
Note: Do not install seals at this time.
Illustration 4 g00894678
5. Install spacer (38) onto spindle (33).
Illustration 5 g00895166
3/19(W)w
2020/3/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...