This document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including planetary gears, bearings, seals, and hubs. The assembly procedure lists 13 steps for installing the components in reverse order and includes precautions like applying clean oil and controlling bearing temperatures. Proper installation of shafts and seals is emphasized to ensure correct bearing preload.
This document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 different parts from the final drive assembly, including planetary gears, bearings, seals, and hubs. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, applying clean oil and controlling part temperatures to ensure proper installation. Special care must be taken when installing seals and shafts.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are given to clean parts and ensure proper alignment during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are given to clean parts and apply oil during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are given to clean parts and apply oil during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are noted to clean parts and apply oil during assembly.
This document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 different parts from the final drive assembly, including planetary gears, bearings, seals, and hubs. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, applying clean oil and controlling part temperatures to ensure proper installation. Special care must be taken when installing seals and shafts.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are noted to clean parts and apply oil during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive by removing components such as the planetary carrier, gears, seals, and hub. It then describes 19 steps for reassembling the final drive, including pressing components in place and using heat to install seals and bearings, verifying proper rotation of gears. Precautions are noted such as applying clean oil and avoiding excessive force.
This document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 different parts from the final drive assembly, including planetary gears, bearings, seals, and hubs. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, applying clean oil and controlling part temperatures to ensure proper installation. Special care must be taken when installing seals and shafts.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are given to clean parts and ensure proper alignment during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are given to clean parts and apply oil during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are given to clean parts and apply oil during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are noted to clean parts and apply oil during assembly.
This document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 different parts from the final drive assembly, including planetary gears, bearings, seals, and hubs. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, applying clean oil and controlling part temperatures to ensure proper installation. Special care must be taken when installing seals and shafts.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then lists 17 steps for reassembling the final drive, including pressing components in place and using tools and heat treatment to install seals and bearings correctly. Precautions are noted to clean parts and apply oil during assembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. It describes 19 steps to disassemble the final drive by removing components such as the planetary carrier, gears, seals, and hub. It then describes 19 steps for reassembling the final drive, including pressing components in place and using heat to install seals and bearings, verifying proper rotation of gears. Precautions are noted such as applying clean oil and avoiding excessive force.
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...onyvzcwadtu05
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction and exhaust systems. Each part is listed with its part number, quantity, description, and any relevant comments.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...onyvzcwadtu05
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for assembling the main hydraulic pump on an excavator model. It lists the required tools and parts. It then provides 49 steps with accompanying illustrations, describing how to install each component of the pump in detail, including bearings, seals, pistons, springs, and valves. The final step instructs the technician to install the assembled pump.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include removing the right side console cover, disconnecting control rods from the valve spools using pins and cotter pins, labeling and disconnecting all oil lines, and removing bolts to take off the pilot control valve. Reinstallation involves installing the pilot control valve on the bracket with bolts, connecting the labeled oil lines, and attaching the control rods to the valve spools with pins and cotter pins.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It then explains how to clean and prepare the parts for installation and use the tools to reinstall the components in reverse order.
3) Fourteen steps are outlined to remove the carrier and twelve steps are provided to install it back into the final drive assembly.
The document provides instructions for disassembling and assembling the steering clutch and brake of a Caterpillar D7R track-type tractor. It details 20 steps to disassemble the components which include removing bolts, plates, bearings, seals and other parts. The 20 steps to assemble are also outlined and include cleaning parts, applying oil, heating bearings, and reinstalling components in reverse order. Special safety precautions are noted regarding spring loaded components.
The document provides assembly instructions for installing a final drive on a D7R track-type tractor. It describes 31 steps to assemble bearings, seals, gears, shafts, covers and other components. Tools required include drivers, seal installers, brackets and spacers. Precise torques and clearances are specified. The assembly is completed by filling the final drive with oil and reconnecting the track.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...onyvzcwadtu05
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...onyvzcwadtu05
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
This document provides instructions for disassembling and assembling the final drives on a D7H track-type tractor. The main steps for disassembly are to remove the final drives from the machine, then disassemble the internal components which include removing planet carriers, gears, shafts, and bearings. For assembly, the components are installed in reverse order, with specifics on cleaning, heating/cooling parts, and using installation tools to properly set clearances and ensure metal-to-metal contact between parts.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining oil, removing the sprocket and various components using specialized tools, cleaning surfaces, replacing seals, installing new components in reverse order, and filling with oil. Proper alignment and torque specifications are noted throughout.
The document provides instructions for removing and installing final drive case assemblies on a D7G track-type tractor. It describes draining oil from the final drive case and removing components like caps, locks, nuts, seals and bearings. It explains using tools and hoists to separate the sprocket, holder assembly and adjusting nut as a unit from the tapered sprocket shaft. Finally, it outlines reinstalling the sprocket assembly and adjusting the bearings.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...onyvzcwadtu05
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction and exhaust systems. Each part is listed with its part number, quantity, description, and any relevant comments.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...onyvzcwadtu05
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for assembling the main hydraulic pump on an excavator model. It lists the required tools and parts. It then provides 49 steps with accompanying illustrations, describing how to install each component of the pump in detail, including bearings, seals, pistons, springs, and valves. The final step instructs the technician to install the assembled pump.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include removing the right side console cover, disconnecting control rods from the valve spools using pins and cotter pins, labeling and disconnecting all oil lines, and removing bolts to take off the pilot control valve. Reinstallation involves installing the pilot control valve on the bracket with bolts, connecting the labeled oil lines, and attaching the control rods to the valve spools with pins and cotter pins.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It then explains how to clean and prepare the parts for installation and use the tools to reinstall the components in reverse order.
3) Fourteen steps are outlined to remove the carrier and twelve steps are provided to install it back into the final drive assembly.
The document provides instructions for disassembling and assembling the steering clutch and brake of a Caterpillar D7R track-type tractor. It details 20 steps to disassemble the components which include removing bolts, plates, bearings, seals and other parts. The 20 steps to assemble are also outlined and include cleaning parts, applying oil, heating bearings, and reinstalling components in reverse order. Special safety precautions are noted regarding spring loaded components.
The document provides assembly instructions for installing a final drive on a D7R track-type tractor. It describes 31 steps to assemble bearings, seals, gears, shafts, covers and other components. Tools required include drivers, seal installers, brackets and spacers. Precise torques and clearances are specified. The assembly is completed by filling the final drive with oil and reconnecting the track.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...onyvzcwadtu05
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...onyvzcwadtu05
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
This document provides instructions for disassembling and assembling the final drives on a D7H track-type tractor. The main steps for disassembly are to remove the final drives from the machine, then disassemble the internal components which include removing planet carriers, gears, shafts, and bearings. For assembly, the components are installed in reverse order, with specifics on cleaning, heating/cooling parts, and using installation tools to properly set clearances and ensure metal-to-metal contact between parts.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining oil, removing the sprocket and various components using specialized tools, cleaning surfaces, replacing seals, installing new components in reverse order, and filling with oil. Proper alignment and torque specifications are noted throughout.
The document provides instructions for removing and installing final drive case assemblies on a D7G track-type tractor. It describes draining oil from the final drive case and removing components like caps, locks, nuts, seals and bearings. It explains using tools and hoists to separate the sprocket, holder assembly and adjusting nut as a unit from the tapered sprocket shaft. Finally, it outlines reinstalling the sprocket assembly and adjusting the bearings.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6T TRACK-TYPE TRACTOR KJL
Configuration: D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
D6T Track-Type Tractor Power Train
Media Number -KENR5126-07 Publication Date -01/01/2013 Date Updated -25/07/2018
i05236991
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
138-7573 Link Bracket 3
1A-2029 Bolt 1
B 1P-510 Driver Group 1
C
FT-1934 Beam 1
6V-3160 Double Acting Cylinder 1
6V-9061 Pump Group 1
1D-4621 Bolt 4
D
138-7574 Link Bracket 2
2A-1538 Bolt 2
Start By:
A. Remove the final drives. Refer to Disassembly and Assembly, "Final Drive - Remove" for
the correct procedure.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/6
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01195912
1. Install Tooling (A) and a suitable lifting device to planetary carrier (3) .
2. Remove bolts (1). Remove planetary carrier (3) and the two O-ring seals from the hub. The
weight of planetary carrier (3) is approximately 137 kg (302 lb).
3. Remove retainers (2) .
Illustration 2 g00841089
4. Place support under planetary carrier (3) in order to prevent damage. Use Tooling (B) and a
suitable press to remove the planetary gear shafts.
5. Remove planetary gears (4) from planetary carrier (3) .
2/6
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00841091
6. Remove bearing cones (5) from gears (4) .
7. Remove the bearing cups from each side of the gears.
Illustration 4 g00841092
Illustration 5 g01195913
8. Remove bolts (6) and retainer (7) .
3/6
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 9. Attach a suitable lifting device to hub (12) and ring gear (8). The weight of hub (12) and
ring gear (8) is approximately 68 kg (150 lb). Remove hub (12) and ring gear (8) .
Illustration 6 g01195915
10. Turn over hub (9) and ring gear (8). Remove retaining ring (10). Attach a suitable lifting
device to hub (9). The weight of hub (9) is approximately 37 kg (82 lb). The weight of ring
gear (8) is approximately 32 kg (71 lb). Remove hub (9) .
Illustration 7 g00841095
11. Install Tooling (C) on hub (12).
Note: Do not lift hub (12) too high. Do not allow hub (12) to contact the fitting on the
hydraulic cylinder.
12. Use Tooling (C) to loosen hub (12) from spindle (13). Remove Tooling (C) .
13. Remove bearing cone (11) .
4/6
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g01195917
14. Install Tooling (D) and a suitable lifting device to hub (12). Remove hub (12) from spindle
(13). The weight of hub (12) is approximately 180 kg (397 lb).
Illustration 9 g00841099
15. Turn over hub (12). Remove Duo-Cone seal kit (15). Use a hammer and a punch to remove
bearing cup (16) .
16. Turn over the hub. Remove bearing cup (14) from the hub.
Note: If the Duo-Cone seal will be reused, mark the seal kits for installation purposes.
5/6
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g00841101
Note: Bearing cone (18) may be damaged if the bearing cone is removed from spindle (13) .
17. Remove Duo-Cone seal (19) from spindle (13) .
18. If necessary, remove bearing cone (18) from the spindle.
19. Remove lip seal (17) from spindle (13) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 18:40:14 UTC+0800 2021
6/6
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6T TRACK-TYPE TRACTOR KJL
Configuration: D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
D6T Track-Type Tractor Power Train
Media Number -KENR5126-07 Publication Date -01/01/2013 Date Updated -25/07/2018
i06701251
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
138-7573 Link Bracket 3
1A-2029 Bolt 3
B 1P-0520 Driver Gp 1
D
138-7574 Link Bracket 2
2A-1538 Bolt 2
E 8M-9395 Installer 1
1. Apply clean oil to all the parts during assembly.
1/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 1 g06081205
2. Use Tooling (B) to install lip seal (17) in spindle (13) to a depth of (X) 9 ± 0.25 mm
(0.3543 ± 0.0098 inch). Put clean oil on the lip of the seal.
Note: Dimension (X) is measured from the face of the spindle to the top of the metal can of
the lip seal in the orientation shown.
Note: Do not apply excessive force to lip seal (17) during installation to avoid damaging the
seal.
Illustration 2 g00841209
3. Raise the temperature of bearing cone (18) to a maximum temperature of 135 °C (275 °F).
Install bearing cone (18) on spindle (13).
Note: Before the installation of the Duo-Cone seal, refer to Disassembly and Assembly,
"Duo-Cone Floating Seals - Install" for the correct procedure.
4. Use Tooling (E) to install the Duo-Cone seal on spindle (13).
2/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 3 g00841210
5. Lower the temperature of bearing cups (14) and (16). Install bearing cups (14) and (16) in
hub (12).
6. Use Tooling (E) to install the Duo-Cone seal in hub (12).
Illustration 4 g01195917
7. Install Tooling (D) on hub (12). Attach a suitable lifting device to Tooling (D). Carefully
position hub (12) on spindle (13).
Illustration 5 g00841212
3/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 8. Raise the temperature of bearing cone (11). Install bearing cone (11) on spindle (13).
Illustration 6 g01195915
9. Attach a suitable lifting device to hub (9) and position hub (9) in ring gear (8). Install
retaining ring (10).
Illustration 7 g01195913
10. Turn over the hub (9) and ring gear (8). Attach a suitable lifting device to hub (9) and the
ring gear (8) into position in hub (12).
Illustration 8 g00841092
4/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 11. Put retainer (7) into position. Install bolts (6) while the hub is slowly rotated. Tighten bolts
(6) evenly to a torque of 135 ± 15 N·m (100 ± 11 lb ft). The retainer must contact the end of
spindle (13) after bolts (6) have been tightened.
Illustration 9 g00841213
12. Lower the temperature of bearing cups (20) and (21). Install the bearing cups in three
planetary gears (4).
Illustration 10 g00841215
5/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 11 g00841216
13. Position the planetary carrier in a press. The shaft (22) must be in position with proper
support to be a positive stop for the shaft.
NOTICE
The shaft must be correctly installed. If the shaft is incorrectly
installed, the bearing preload will be incorrect. This will result in
component damage.
14. Position planetary gear (4) in the planetary carrier.
15. Lower the temperature of shaft (22). Use a suitable press to install the shaft in the planetary
carrier. After the installation, the end of shaft (22) must be flush with the retainer of the
planetary carrier. This will provide the correct bearing preload. The gear must rotate by
hand after installation. If the gear does not rotate, the problem must be corrected. Repeat
this procedure for all three shafts.
Illustration 12 g01195912
16. Install three retainers (2) on shafts (22).
6/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 17. Install Tooling (A). Attach a suitable lifting device to Tooling (A). Install the two O-ring
seals on the planetary carrier. Align the drain hole in the planetary carrier with the drain
hole in the hub.
18. Position the planetary carrier in the hub.
19. Install bolts (1) that hold planetary carrier (3) to the hub. Remove Tooling (A).
End By:
a. Install the final drives. Refer to Disassembly and Assembly, "Final Drive - Install" for the
correct procedure.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 18:41:14 UTC+0800 2021
7/7
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6T TRACK-TYPE TRACTOR KJL
Configuration: D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
D6T Track-Type Tractor Power Train
Media Number -KENR5126-07 Publication Date -01/01/2013 Date Updated -25/07/2018
i03576221
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1952 Installer 1
B
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
1D-4593 5/8 - 11 by 5 1/2 bolt 2
4K-0367 5/8 - 11 by nut 2
5P-8248 Washer 4
1/4
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g00826743
1. Adjust the top bracket of Tooling (B) until Dimension (X) is 222.25 mm (8.750 inch).
Attach Tooling (B) to the final drive.
Illustration 2 g00865095
2. Use Tooling (B) to install final drive (1). The weight of final drive (1) is approximately
454 kg (1000 lb).
Illustration 3 g00865094
3. Install bolts (7) that hold the final drive and the steering clutch and brake together. Tighten
bolts (7) to a torque of 700 ± 90 N·m (516 ± 66 lb ft).
2/4
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 4 g00865082
4. Remove Tooling (B) from the final drive.
Illustration 5 g00865077
5. Install two bolts (6) to the sprocket segment.
Illustration 6 g00865075
6. Install two bolts (5).
Illustration 7 g00865024
3/4
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 7. Use Tooling (A) to install axle (4). Remove Tooling (A).
Note: Carefully install the axle shaft (4) into the final drive (1). It is possible that the axle
shaft (4) could damage the lip seal.
Illustration 8 g00865052
8. Install cover (3) and bolts (2) on final drive (1).
End By:
a. Connect the track. Refer to Disassembly and Assembly, "Track - Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 18:42:14 UTC+0800 2021
4/4
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6T TRACK-TYPE TRACTOR KJL
Configuration: D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
D6T Track-Type Tractor Power Train
Media Number -KENR5126-07 Publication Date -01/01/2013 Date Updated -25/07/2018
i02553052
Final Drive, Steering Differential, and Brake (Left Side) -
Remove
SMCS - 4050-011-LT; 4131-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5B-4274 (3/8 - 16 NC - 3 1/2) 3
B 8T-3207 Lifting Bracket 1
C 138-7575 Link Bracket 1
D 8S-9906 Ratchet Puller 1
Start By:
a. Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
b. Remove the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
c. Remove the steering motor. Refer to Disassembly and Assembly, "Steering Motor -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
1/5
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Drain the hydraulic oil from the hydraulic system into a suitable container for storage or
disposal.
2. Remove the floorplate.
3. Remove the plate under the seat.
Illustration 1 g01202478
2/5
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 4. Remove bolts (1).
Illustration 2 g01202481
5. Install Tooling (A) and remove housing (2).
Illustration 3 g01202482
6. Remove bolt (3) from hand rail (4). Position hand rail (4) out of the way. This will allow
more room for Tooling (B).
3/5
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 4 g01202483
Illustration 5 g01202485
7. Remove bolts (5). Do not remove bolt (6) and install Tooling (C). Remove two bolts (7).
8. Remove two bolts from the top of the sprocket segment. Install Tooling (B). Adjust the
hook of Tooling (B) to the maximum length.
9. Remove the bolts and washers (5). Remove the bolt and washer (7). Do not remove bolt (6).
Illustration 6 g00870958
10. Attach Tooling (D) to Tooling (C) and Tooling (B).
4/5
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. 11. Remove the remaining bolts (5). Separate the final drive approximately 152 mm (6.0 inch).
12. Release the pressure on Tooling (D). Rotate brake housing 90 degrees in the
counterclockwise direction.
Illustration 7 g01202489
13. Rotating the brake housing allows pinion (8) to point forward. Rotating the brake housing
will allow the final drive to swing toward the front of the machine. Rotating the brake
housing will allow clearance for the ring gear to clear the machine. The weight of the final
drive assembly is approximately 680 kg (1500 lb).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 1 18:43:14 UTC+0800 2021
5/5
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6T TRACK-TYPE TRACTOR KJL
Configuration: D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
D6T Track-Type Tractor Power Train
Media Number -KENR5126-07 Publication Date -01/01/2013 Date Updated -25/07/2018
i06983834
Steering Differential and Brake - Disassemble
SMCS - 4131-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 138-7573 Link Bracket 2
B 3K-4897 Spring Pin 8
C 6V-4072 Spanner Wrench 1
D
9S-9154 Step Plate 1
6V-3009 Bar 1
8S-6470 Forcing Screw 3/4 inch - 16 by 4 inch 1
8S-5133 Plug 1
5P-8245 Washer 4
1D-4719 Nut 1/2 inch - 13 2
2H-6488 Bolt 1/2 inch - 13 by 5 inch 2
E 9S-9154 Step Plate 1
6V-3009 Bar 1
8S-6470 Forcing Screw 3/4 inch - 16 by 4 inch 1
8S-5133 Plug 1
5P-8245 Washer 4
1/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. 1D-4719 Nut 1/2 inch - 13 2
1D-4574 Bolt 1/2 inch - 13 by 6 inch 2
8H-0663 Bearing Puller 1
F 138-7575 Link Bracket 3
G
8B-7550 Leg 2
8B-7559 Adapter 2
3H-0465 Plate 4
1P-0498 Plate 1
1B-4207 Nut 3/4 inch - 16 2
5H-9976 Forcing Screw 1 inch - 14 by 5 3/4 inch 1
5B-0637 Nut 1 inch - 14 1
8H-0684 Ratchet Wrench 1
8B-7563 Handle 1
5F-7353 Washer (Thrust) 1
8B-7548 Push-Puller Tool Gp 1
Start By:
a. Remove the left final drive, the steering differential, and the brake. Refer to Disassembly
and Assembly, "Final Drive, Steering Differential, and Brake (Left Side) - Remove"
.
2/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 2 g00823691
3. Attach Tooling (A) and a suitable lifting device.
4. Remove sliding carrier (3). The weight of sliding carrier (3) is approximately 48 kg
(105 lb).
5. Remove Tooling (A).
4/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 3 g06187075
6. Remove remaining bolts (2) and slinger (4) from planetary carrier (7).
7. Remove retaining ring (5), thrust ring (5A), and planetary carrier (7) from ring gear (6).
Illustration 4 g00823775
8. Remove seal ring (10) from planetary carrier (7).
9. Use a hammer and a punch to push pin (12) in shaft (11).
10. Remove shaft (11), planetary gear (9), discs (8), and bearing (13) from planetary carrier (7).
11. Remove pin (12) from shaft (11).
12. Repeat Steps 9 through 11 for the remaining planetary gears.
5/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 5 g00823759
13. Remove lockring (14) and remove retaining ring (16).
14. Remove sun gear (15) from planetary carrier (18).
15. Remove spacer (17).
6/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Illustration 6 g00823816
16. Remove bolts (19), plate (20), and gear (21) from planetary carrier (18).
17. Use Tooling (B) to compress the retaining ring that holds planetary carrier (18) in ring gear
(6).
18. Separate planetary carrier (18) from ring gear (6).
19. Remove the retaining ring from planetary carrier (18).
20. Use a hammer and a punch to push pin (23) in shaft (24).
7/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Illustration 7 g00823872
21. Remove shaft (24), planetary gear (22), discs (26), and bearing (25) from planetary carrier
(18).
22. Remove pin (23) from shaft (24).
23. Repeat Steps 20 through 22 for the remaining planetary gears.
8/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. Illustration 8 g00823878
24. Place a bolt in the teeth of bevel pinion (27) to prevent movement.
9/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (MA...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
33. Illustration 9 g00823884
25. Bend the tang on lock washer (29) away from nut (28).
26. Use Tooling (C) to remove nut (28) from the pinion.
27. Remove lockwasher (29) and washer (30) from the pinion.
28. Remove bolt (32).
29. Remove planetary carrier (31) from the support bracket.
10/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (M...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
34. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
35. Illustration 10 g00823890
30. Use Tooling (D) to force bevel pinion (27) from bearing cone (33) and planetary carrier
(31).
11/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (M...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
36. Illustration 11 g00824243
31. Use Tooling (E) to remove bearing cone (34) from planetary pinion (27).
12/22
D6T TRACK-TYPE TRACTOR XW, LGP Differential Steering KJL00001-UP (M...
2021/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...