The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: D25D ARTICULATED TRUCK 1HK
Configuration: D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D25D,D30D AND D350D ARTICULATED DUMP TRUCKS VEHICLE SYSTEMS
Media Number -SENR8210-01 Publication Date -01/03/2005 Date Updated -05/12/2017
SENR82100029
Hitch Group
SMCS - 7057; 7113-011; 7113-012
Remove Hitch Group
Start By:
a. separation of tractor from body
1. Remove bolt (4) and drain the oil from the hitch tube.
2. Remove bolts (2) from the drive shaft at the hitch area.
3. Remove nut lock (1) and then remove nut (3).
1/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 4. Remove bolts (6) from the drive shaft.
5. Remove four bolts (7) at the carrier bearing.
6. Lower the drive shaft (5) to the floor.
7. Remove all the bolts from the hitch yoke retainer.
8. Install two suitable guide bolts (8) in the retainer.
9. Remove hitch yoke retainer (9).
10. Remove and inspect Large O-ring seal (10) from the retainer.
11. Remove bolts (12) to remove yoke assembly (11) from the retainer.
2/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 12. Remove and inspect O-ring seal (13) from the yoke assembly
13. Remove external retaining ring (14) with tool (A).
14. Remove yoke from the flange.
15. Remove internal retaining ring (15) from the flange with tool (A).
16. Put the flange in position in a press.
17. Use tool (B) and the press to push the bearing from the flange.
3/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 18. Use tool (B) and a press to gently push the seal from the flange.
19. Remove shaft (16) from the hitch housing.
20. Remove and inspect O-ring seals (17).
21. Go to the front of the hitch. Remove bolts (18) to remove the other hitch yoke retainer (19).
NOTE: Use Steps 10 thru 18 to disassemble hitch yoke retainer (19).
22. Install tooling (C) on the hitch group and then fasten a hoist.
23. Remove hitch group (20) from its housing.
NOTE: Tool (D) can be used as an alternate tool to remove hitch group (20).
4/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 24. Remove front seal (21) and bearing assembly (22) from the hitch housing if necessary.
25. Remove rear seal (23) and bearing assembly (24) from the hitch housing if necessary.
Install Hitch Group
1. Install a new rear bearing assembly (24) and rear seal assembly (23) in the hitch housing if
necessary.
5/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 2. Install a new front bearing assembly (22) and front seal (21) in the hitch housing if necessary.
3. Install tooling (C) on the hitch group and then fasten a hoist.
NOTE: Tool (D) can be used as an alternate tool to install hitch group (20).
4. Put hitch group (20) in position in the hitch housing.
5. Install the seal and bearing in the retainer flange with tool group (B).
6. Install internal retaining ring (15) in retainer flange with tool (A).
7. Install yoke on the retainer flange.
8. Install external retaining ring (14) with tool (A).
6/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 9. Install a new O-ring seal (13) on the yoke assembly.
10. Put front hitch yoke retainer assembly (19) in position in the hitch housing.
11. Install bolts (18) that holds the hitch yoke retainer assembly in position in the hitch housing.
12. Install shaft (16) in the hitch housing.
13. Install new O-ring seal (17).
NOTE: Use Steps 5 thru 9 to assemble hitch yoke retainer assembly (9).
14. Install yoke assembly (11) on the retainer with bolts (12).
7/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 15. Install a new O-ring seal (10) on the retainer.
16. Install two suitable guide bolts (8) and install hitch yoke retainer assembly (9).
17. Install the bolts that hold the yoke retainer assembly. Remove the two guide bolts.
18. Raise the drive shaft (5) into position and install four bolts (7) at the carrier bearing.
19. Install bolts (6) on the drive shaft.
20. Install hitch thrust flange (3) with nut lock (1).
21. Install bolts (2) on the drive shaft at the hitch area.
22. Put the correct amount of oil in the hitch tube and install bolt (4).
8/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End By:
a. connection of tractor to body
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 20:55:27 UTC+0800 2020
9/9
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: D25D ARTICULATED TRUCK 1HK
Configuration: D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D25D,D30D AND D350D ARTICULATED DUMP TRUCKS VEHICLE SYSTEMS
Media Number -SENR8210-01 Publication Date -01/03/2005 Date Updated -05/12/2017
SENR82100030
Suspension Cylinders
SMCS - 7201-010; 7201-017
Remove & Install Suspension Cylinders
The suspension system may drop the machine suddenly, leaving no
clearance between the axle housing, main frame, tires and mud guards.
Working in these areas can result in personal injury or death by
crushing. Stay clear until the engine is stopped and the suspension is
lowered to the service position.
NOTE: Take the weight off the front of the machine by raising it with two 50 ton screw jacks,
also install a suitable floor jack underneath the axle housing.
1. Remove bolts (4) to remove cover (3).
2. Remove bolts (2) and then remove metal guard (1).
1/5
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 3. Fasten strap (5) and a hoist to the suspension cylinder.
4. Remove cylinder mounting pin (6) and then remove suspension cylinder (7). Weight of the
suspension cylinder is 39 Kg (86 lb.).
The following steps are for the installation of the suspension cylinder.
5. Put the suspension cylinder (7) in position and install the cylinder mounting pin (6).
6. Remove strap (5) and the hoist from the suspension cylinder.
7. Install metal guard (1) and bolts (2).
8. Install rubber cover (3) and bolts (4).
Disassemble & Assemble Suspension Cylinders
2/5
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Start By:
a. remove suspension cylinder
1. Remove one adapter (2) from the suspension cylinder (3). Use tool (E) to remove retainer ring
(1) and tool (F) to remove to retainer rings (5).
2. Remove two grease fittings (6) from the suspension cylinder (3).
3. Remove the retainer (4) from the cylinder.
4. Put the suspension cylinder (3) in an appropriate holding fixture.
5. Use tool (A) to remove the end cap (7) from the suspension cylinder.
3/5
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 6. Separate the rod assembly (9) from the suspension cylinder body.
7. Remove seal (8), wear ring (10) and seal (11) from the rod assembly.
8. Put the rod assembly (9) in position in a suitable holding fixture.
9. Use tool (D) to remove screw (13) from piston (12).
10. Put tool (B) in position on piston (12) and secure it by tightening three screws in tool (B).
11. Put tool (C) on tool (B) and proceed to remove piston (12) from the rod (9).
4/5
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 12. Remove piston (12), valve ring (15), and cushion ring (14) from the rod (9).
13. Inspect bearings (16) in the suspension cylinder body.
14. If it necessary to replace the bearings, put the cylinder body in position in a press and use tool
group (G) to push the bearings from the cylinder body.
NOTE: To assemble the suspension cylinder, use the reverse order of the disassemble procedure
and then follow the steps below.
15. In Step 10, tighten the piston (12) to a torque of 800 N·m (590 lb.ft.).
16. In Step 9, tighten the screw (13) to a torque of 49 N·m (36 lb.ft.).
17. In Step 5, tighten the end cap (7) to a torque of 400 N·m (295 lb. ft.).
End By:
a. install suspension cylinder
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 20:56:22 UTC+0800 2020
5/5
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: D25D ARTICULATED TRUCK 1HK
Configuration: D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D25D,D30D AND D350D ARTICULATED DUMP TRUCKS VEHICLE SYSTEMS
Media Number -SENR8210-01 Publication Date -01/03/2005 Date Updated -05/12/2017
SENR82100031
Brake Shoes
SMCS - 4253-011; 4253-012
Remove Brake Shoes
Start By:
a. remove wheels, bearings and Duo-Cone seals
NOTE: The above operation is in the POWER TRAIN Disassembly And Assembly section.
1. Remove the bolts and cover (1) from the of the brake spider.
1/3
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Use an acceptable brake tool to remove spring (3) that holds brake shoes (2) together.
3. Remove the springs, retainers and felt washers from one end of each pin (4).
4. Remove pins (4) from the spider and remove brake shoes (2) from the spider.
Install Brake Shoes
1. Install the felt washers, retainers and springs one end of pins (1).
2. Put brake shoes (2) in position on the spider and install pins (1).
3. Install the felt washers, retainers and springs on the other end of pins (1) to hold them in
position.
2/3
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 4. Use an acceptable brake tool (3) to install spring (4).
5. Install covers (5) on the back of the brake spider.
End By:
a. install wheels, bearings and Duo-Cone seals
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 23 20:57:18 UTC+0800 2020
3/3
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: D25D ARTICULATED TRUCK 1HK
Configuration: D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
D25D,D30D AND D350D ARTICULATED DUMP TRUCKS VEHICLE SYSTEMS
Media Number -SENR8210-01 Publication Date -01/03/2005 Date Updated -05/12/2017
SENR82100032
Wheel Spindles
SMCS - 4205-011; 4205-012
Remove Wheel Spindles
Start By:
a. remove brake shoes
1. Remove guard (2) from over brake line (1).
2. Disconnect brake line (1) from the wheel brake cylinder assembly.
1/4
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 3. Use tooling (A) and fasten a hoist to wheel spindle (3) and the brake spider.
4. Remove bolts (4) and remove wheel spindle (3) and the brake spider from the axle housing. The
weight of the unit is 59 Kg (130 lb.).
5. Remove the O-ring seal from the back of wheel spindle (3).
6. Remove bolts (5), the locks and bars that hold Duo-Cone seal retainer (6) and the spider in
position.
7. Remove retainer (6) from the spider and wheel spindle.
8. Remove O-ring seal (7) from the back of retainer (6).
9. Remove brake spider (8) from wheel spindle (3).
2/4
D25D, D30D ARTICULATED TRUCK 1HK00674-UP (MACHINE) POWERED BY...
2020/2/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...