Caterpillar cat d9 r track type tractor (prefix wdm) service repair manual (wdm00001 and up)

Service Repair Manual
Models
D9R TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D9R TRACK-TYPE TRACTOR WDM
Configuration: D9R TRACK-TYPE TRACTOR WDM00001-UP (MACHINE) POWERED BY 3408C Engine
Disassembly and Assembly
D9R Track-Type Tractor Power Train
Media Number -SENR5387-14 Publication Date -01/08/2018 Date Updated -30/08/2018
i06194021
Track Roller - Remove
SMCS - 4180-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT2223 Strap Group 1
B 183-4799 Track Roller Lifting Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Loosen the track. See "Separation of Track".
2. Install tool (A) in order to hold the major bogies in position.
1/2
D9R TRACK-TYPE TRACTOR WDM00001-UP (MACHINE) POWERED BY 3408...
2020/4/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

3. In order to remove the track roller, lift that side of the tractor.
Illustration 1 g00626261
4. Fasten a hoist to tool (B) . Put tool (B) under the track roller.
5. Remove four bolts (3) and two caps (2) that hold the track roller to the minor bogie.
6. Remove track roller (4) from the minor bogie with tool (B) . The weight of the track roller is
approximately 97 kg (214 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 17 09:22:00 UTC+0800 2020
2/2
2020/4/17

Shutdown SIS
Previous Screen
i07393407
Track Roller - Disassemble
SMCS - 4180-015
Disassembly Procedure
Start By:
a. Remove the track rollers.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1. Use a hammer and a punch, and drive the plug out of stopper (2).
2. Use a variable speed drill and a 12.7 mm (0.5 inch) drill bit to slowly remove the stopper.
Remove stopper (2) from the ends of the shaft.
3. Remove bolts (3) and retainer (1) from both sides of the track roller.
1/3
2020/4/17

4. Remove O-ring seal (5) from retainer (1).
Note: Put identification marks on the seals in case the seals need to be used again. The seals
can be assembled and installed in the original position.
5. Put identification marks on seal ring (4). Remove the seal ring from retainer (1). Remove
the O-ring seal from the seal ring.
Note: Early track rollers do not have toric stabilizer (7).
6. Put identification marks on seal ring (6). Remove the seal ring and toric stabilizer (7) from
shaft (8).
7. Remove the toric ring from seal ring (6).
2/3
2020/4/17

8. Pull shaft (8) out of the track roller far enough to fasten a hoist to the shaft.
9. Fasten a hoist to shaft (8). Remove the shaft from track roller (9). The weight of the shaft is
18 kg (40 lb).
Fri Apr 17 09:22:59 UTC+0800 2020
3/3
2020/4/17

Shutdown SIS
Previous Screen
i07393455
Track Roller - Assemble
SMCS - 4180-016
Assembly Procedure
Table 1
Required Tools
A 8T-7641 Seal Installer 1
B 8T-0822 Alignment Sleeve 1
C 5P-7419 Plug Installer 1
D Testing Tool 1
E 8S-2328 Dial Indicator 1
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Personal injury can result from acid.
Wear all necessary protective equipment, such as rubber gloves and
goggles when working with acid.
The bottle containing the etchant should be properly marked ACID and
should be stored in a protective place.
1/7
2020/4/17

1. Clean the parts and inspect the parts for wear or for damage. Replace all parts that are
damaged or worn.
Note: The bearing in track roller (9) can be damaged when shaft (8) is installed in the track
roller.
2. Fasten a hoist to shaft (8). Carefully put the shaft in track roller (9).
Note: Early track rollers have no toric stabilizers (7).
3. Put toric stabilizers (7) in position on both ends of shaft (8).
2/7
2020/4/17

Note: See, "Duo-Cone Floating Seals" before installing any of the Duo-Cone seals.
4. Put toric ring (10) in position in seal ring (6). Make sure that the toric ring is straight in seal
ring (6).
5. Use tool (A) to install the toric ring and seal ring (6) on shaft (8). Install the ring until tool
(A) makes contact with the end of the shaft.
3/7
2020/4/17

6. Use a depth micrometer (11) to measure the distance between seal ring (6) and the shaft.
The shaft is 90 degrees and four locations away from seal ring (6). The difference in these
measurements must not be more than 0.8 mm (0.0315 inch).
7. If adjustments to seal ring (6) are necessary, use tool (A) to adjust the seal ring on the shaft.
8. Repeat steps 5 to 9 for installation of the toric ring. Also install the seal ring on the other
side of the track roller.
9. Put O-ring seal (12) in position on seal ring (4). Make sure that the O-ring seal is straight on
the seal ring.
10. Put the O-ring seal and seal ring (4) in position in retainer (1). Use tool (A) to install the seal
ring in the retainer. Install the O-ring seal and seal ring (4) until the O-ring seal makes
contact with the bottom of the retainer.
11. Use depth micrometer (11) to measure the distance from the surface of the retainer to the
surface of seal ring (4). The seal rings can be found at four locations. The difference in these
measurements must not be more than 0.1 mm (0.0039 inch).
12. If adjustments to the seal ring are necessary, use tool (A) to adjust the seal ring in the
retainer.
4/7
2020/4/17

13. Put O-ring seal (5) in position in the groove in retainer (1).
14. Put petroleum jelly or grease on the O-ring seal. The petroleum jelly and grease will hold
the seal in place on the retainers.
15. Make sure that the faces of the seal rings are clean and free of any foreign material.
16. Put a thin film of clean oil on the face of the seal rings.
17. Put tool (A) in position in the bore of retainer (1) and the seal ring. Use tool (B) to put the
retainer and put the seal ring in the original position on the track roller.
5/7
2020/4/17

18. Use tool (B) to hold the seal ring and retainer (1) in the correct position, and install bolts (3).
Tighten the bolts evenly to keep the retainer in alignment with the track roller.
19. Tighten the bolts to a torque of 135 ± 15 N·m (100 ± 11 lb ft).
20. Repeat steps 11 through 22 to install the retainer on the other side of the track roller.
21. Put clean oil on stopper (2). Install the stopper in one end of shaft (8). Install the stopper
10 ± 4 N·m (7.3756 ± 2.9502 lb ft) below the surface of the shaft end.
22. Use tool (C) to install the plug-in stopper (2). Install the plug even with the end of the
stopper.
23. Use tool (D) to pressure test the track roller.
a. Put air free of water under a pressure of 280 kPa (41 psi) into the roller shaft.
b. b. If there is a pressure reduction in 10 seconds or less, there is a leak in the track
roller. The track roller must be disassembled and checked.
6/7
2020/4/17

24. Use tool (E) to check the end play of shaft (8). The end play must be 0.22 to .98 mm
(0.0087 to .0039 inch).
25. Fill track roller shaft (8) with 720 ± 15 mL (24.4 ± .51 oz) of SAE 30 Oil.
26. Put clean oil on the stopper. Install the stopper in the end of shaft (8). Install the stopper
10 ± 4 mm (0.394 ± 0.158 inch) below the surface of the end of the shaft.
27. Use tool (C) to install the plug in the stopper. Install the plug even with the end of the
stopper.
End By:
a. Install the track rollers.
Fri Apr 17 09:23:59 UTC+0800 2020
7/7
2020/4/17

Shutdown SIS
Previous Screen
i06194032
Track Roller - Install
SMCS - 4180-012
Installation Procedure
Table 1
Required Tools
A FT2223 Strap Group 1
B 183-4799 Track Roller Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1/2
2020/4/17

1. Use a hoist and tool (B) and put track roller (4) in position in the minor bogie.
2. Align the pin in caps (2) with the hole in the track roller shaft, and install caps (2) and bolts
(3) . Tighten the bolts to a torque of 750 ± 75 N·m (553 ± 55 lb ft).
3. Put track guide in position on the major bogie. Install the bolts that hold the major bogie in
place. Tighten the bolts to a torque of 475 ± 50 N·m (350 ± 37 lb ft).
4. Lower the tractor to the ground and remove tool (A) .
5. Adjust the track. Refer to Disassembly and Assembly, "Track - Connect"
Fri Apr 17 09:24:58 UTC+0800 2020
2/2
2020/4/17

Shutdown SIS
Previous Screen
i07394827
Track Adjuster - Remove
SMCS - 4157-011
Removal Procedure
Start By:
a. Remove the front track roller frame.
1. Remove bolt (1) and the spacer from cable (2).
1/2
2020/4/17

2. Fasten an appropriate lifting device to track adjuster (3). Remove the track adjuster from the
recoil spring. The weight of the track adjuster is 113 kg (249 lb).
Fri Apr 17 09:25:57 UTC+0800 2020
2/2
2020/4/17

Shutdown SIS
Previous Screen
i01027944
Track Adjuster - Disassemble
SMCS - 4157-015
Disassembly Procedure
Table 1
Required Tools
A 6V-4947 Hydraulic Cylinder Repair Stand 1
Start By:
a. Remove the track adjusters. See Disassembly and Assembly, "Track Adjuster - Remove".
1. Put the track adjuster in position on tool (A).
2. Remove cylinder (2) and piston (3) from cylinder assembly (1).
1/4
2020/4/17

3. Remove spiral ring (5) and retainer ring (4) from the piston.
4. Remove seal assembly (6) from the piston.
5. Remove seal rings (7) and (8) from the seal.
2/4
2020/4/17

6. Remove wear rings (9) from the cylinder.
7. Remove cylinder (2) from the piston.
8. Remove wear rings (10) from the inside of the cylinder.
Fri Apr 17 09:26:57 UTC+0800 2020
3/4
2020/4/17

Shutdown SIS
Previous Screen
i01027945
Track Adjuster - Assemble
SMCS - 4157-016
Assembly Procedure
Table 1
Required Tools
A 6V-4947 Hydraulic Cylinder Repair Stand 1
1. Put the wear rings in SAE 30 oil. Make sure that the rings are in the oil for a long enough
time period so that the rings become filled and saturated with the oil.
2. Install wear rings (10) on the inside of the cylinder.
1/4
2020/4/17

3. Install cylinder (2) on the piston.
4. Put wear rings (9) in position on the cylinder.
5. Put seal rings (7) and (8) in position on the seal.
2/4
2020/4/17

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

6. Install seal assembly (6) on the piston.
7. Install retainer ring (4) and spiral ring (5) on the piston.
8. Put cylinder assembly (1) in position on tool (A). Put SAE 30 oil on the seals.
NOTICE
3/4
2020/4/17

Make sure that you do not damage the seal when you install piston (3)
and cylinder (2) in the cylinder. Make sure that the lip of the seal goes
past the chamfer in the cylinder.
9. Install piston (3) and cylinder (2) into the cylinder assembly.
End By:
a. Install the track adjusters. See Disassembly and Assembly, "Track Adjuster - Install".
Fri Apr 17 09:27:56 UTC+0800 2020
4/4
2020/4/17

Shutdown SIS
Previous Screen
i07395126
Track Adjuster - Install
SMCS - 4157-012
Installation Procedure
1. Fasten an appropriate lifting device to track adjuster (3).
2. Put the track adjuster in position in the front track roller frame.
1/2
2020/4/17

Caterpillar cat d9 r track type tractor (prefix wdm) service repair manual (wdm00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

More from fjkskmmdmme

More from fjkskmmdmme (20)

Recently uploaded

Recently uploaded (19)

Caterpillar cat d9 r track type tractor (prefix wdm) service repair manual (wdm00001 and up)