The document provides instructions for disassembling the cylinder head of a D11N track-type tractor. The procedures include removing the inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
2. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11N TRACK-TYPE TRACTOR 4HK
Configuration: D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine
Disassembly and Assembly
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Media Number -SENR1126-33 Publication Date -01/07/2015 Date Updated -14/09/2018
i02415328
Electronic Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Pry Bar 1
Start By:
a. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft Assembly and Push Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00903832
1. Remove bolt (1) and the clamp.
2. Remove bolt (2) and the clamp.
3. Disconnect harness assembly (3).
Illustration 2 g00903932
4. Use Tooling (A) to remove electronic unit injector (4).
5. Remove fuel / fluids from the cylinder. WARNING! Turning over (cranking) an engine
with an injector removed could result in personal injury or death from fluids escaping at
high velocity.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 22 09:50:57 UTC+0800 2020
2/2
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11N TRACK-TYPE TRACTOR 4HK
Configuration: D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine
Disassembly and Assembly
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Media Number -SENR1126-33 Publication Date -01/07/2015 Date Updated -14/09/2018
i02415334
Electronic Unit Injector - Install
SMCS - 1290-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 9U-6862 Tapered Brush 1
C 4C-5027 Tap Wrench 1
D 4C-6774 Vacuum Gun Kit 1
E 1P-0808 Multipurpose Grease 1
F
1U-5512
or
8T-7765
Abrasive Material
or
Surface Reconditioning Pad
1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Remove all carbon deposits from the angled surface at the bottom of
the cylinder head bore for the fuel injection pump. Failure to clean this
area may prevent the fuel injection pump from seating properly. This
could result in failure of the fuel injection pump due to leakage of
exhaust gas into the fuel passage.
1. It is important to clean the cylinder head bore for the electronic unit injector before you
install the electronic unit injector. Use the following procedure to clean the bore.
Note: A fine grade of Scotch Brite material is recommended for cleaning the cylinder
head bore for the electronic unit injector. The product is available as Tooling (F).
a. Place a 38 mm (1.5 inch) square piece of Scotch Brite material on the end of Tooling
(B).
Note: It should not be necessary to use a power tool to clean the cylinder head bore
for the electronic unit injector.
Illustration 1 g01051051
b. Hold the brush with Tooling (C). Insert the brush into bore (5). Rotate the Scotch
Brite material against the lower surface of bore (6). Continue cleaning until the
surface is smooth and shiny.
Note: Tooling (D) is recommended for cleaning loose particles from the bore. The
vacuum is operated with pressurized air.
c. Remove all loose particles from the bore.
2. Remove any fuel / fluid that may have accumulated before installing the injector.
2/4
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 2 g01051052
3. Inspect O-ring seals (7) and (8) for good condition. Obtain new O-ring seals, if necessary.
Coat the O-ring seals and coat the cylinder head bore for the electronic unit injector with
Tooling (E).
4. Press the electronic unit injector into the bore of the cylinder head. Do not strike the
electronic unit injector. Center the solenoid between the valve springs.
Note: Adjust the height of the electronic unit injector according to the Service Manual,
"Specifications".
Illustration 3 g01052571
5. To seat electronic unit injector (4) into the bore, install the clamp with bolt (2) and the
washer. Tighten the bolt to a torque of 65 ± 7 N·m (48 ± 5 lb ft).
6. Connect harness assembly (3) to the connector. Tighten the terminal nuts to a torque of
1.70 ± 0.25 N·m (15 ± 2 lb in).
7. Press the harness assembly into the groove in the valve cover base.
3/4
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 8. Install bolt (1) and the clamp.
End By:
a. Install the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Push Rods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 22 09:51:57 UTC+0800 2020
4/4
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11N TRACK-TYPE TRACTOR 4HK
Configuration: D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine
Disassembly and Assembly
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Media Number -SENR1126-33 Publication Date -01/07/2015 Date Updated -14/09/2018
i02414981
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
a. Remove the valve cover base. Refer to Disassembly and Assembly, "Valve Cover Base -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow dirt to enter the fuel system. Thoroughly clean the area
around a fuel system component that will be disconnected. Fit a
suitable cover over disconnected fuel system component.
1/5
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change".
Illustration 1 g01053854
2. Remove bolts (1) and (2). Remove tube (3).
Illustration 2 g01053859
2/5
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Remove four bolts (4) (not shown) from exhaust tube assembly and remove four bolts (5)
(not shown) from inlet tube assembly.
Illustration 3 g01053860
4. Remove bolts (6). Use a suitable lifting device and Tooling (A) in order to remove cylinder
head assembly (7). The weight of cylinder head assembly (7) is approximately 47 kg
(104 lb). Remove gasket (8).
Illustration 4 g01053975
5. Remove seals (9) and (10), and O-ring seal (11) from the spacer plate.
3/5
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 5 g01053977
6. Remove spacer plate (12) from the dowels in the cylinder block.
Illustration 6 g01053978
7. Remove gasket (13) from the dowels.
Illustration 7 g01053983
8. Remove the O-ring seal from dowel (14).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Sat Feb 22 09:52:56 UTC+0800 2020
4/5
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11N TRACK-TYPE TRACTOR 4HK
Configuration: D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine
Disassembly and Assembly
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Media Number -SENR1126-33 Publication Date -01/07/2015 Date Updated -14/09/2018
i02048542
Cylinder Head - Disassemble
SMCS - 1100-015
Disassembly Procedure
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
Inlet and Exhaust Valves
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 8S-2263 Spring Tester 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00905560
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g00618922
1. Use Tooling (A) to compress valve spring (1).
2. Remove retainer lock (2).
3. Release the tension on Tooling (A). Remove Tooling (A).
4. Remove valve rotator (3), outer spring (5), inner spring (4), and seal (6).
Note: If the valves will be reused, mark the valves for identification upon assembly.
5. Remove valve (7) from the cylinder head.
6. Use Tooling (B) to measure the force of the valve springs. Refer to Specifications for the
correct spring force.
7. Repeat Steps 1 through 6 for the remaining valves.
Bridge Dowels
Table 2
Required Tools
Tool Part Number Part Description Qty
C 5P-0944 Dowel Puller Group 1
3/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5P-0942 Dowel Extractor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01051069
1. If the bridge dowels will be replaced, use Tooling (C) to remove bridge dowel (8) from the
cylinder head.
Inlet and Exhaust Valve Seat Inserts
Table 3
Required Tools
Tool Part Number Part Description Qty
D 166-7441 Valve Seat Extractor Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (D) to remove the valve seat inserts from the cylinder head.
2. Thoroughly clean valve seat bores in the cylinder head.
4/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Inlet and Exhaust Valve Guides
Table 4
Required Tools
Tool Part Number Part Description Qty
E
7M-3975 Valve Guide Driver 1
5P-1729 Valve Guide Bushing 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (E) and a hammer to remove the valve guides from the cylinder head.
Valve Lifters
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The valve lifters may also be removed with the cylinder head on the engine. Remove the
camshaft and use the following steps in order to remove the valve lifters with the cylinder head on
the engine.
Illustration 4 g01051072
5/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g01051073
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Pull valve lifter (9) out of the cylinder head.
2. Remove guide spring (10) from the valve lifter.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 22 09:53:55 UTC+0800 2020
6/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11N TRACK-TYPE TRACTOR 4HK
Configuration: D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine
Disassembly and Assembly
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Media Number -SENR1126-33 Publication Date -01/07/2015 Date Updated -14/09/2018
i06795257
Cylinder Head - Assemble
SMCS - 1100-016
Assembly Procedure
Valve Lifters
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01051073
1/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01051072
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Install the lifter assembly into the cylinder head. Ensure that the word "LEFT"
stamped on end of the bronze pin is always oriented to the LEFT as viewed from the side of
the engine regardless of left side or right side bank. Immerse the lifter assembly in engine
oil before assembled in the cylinder head lifter bore.
1. Install new guide spring (10) for valve lifter (9).
2. Place valve lifter (9) in a container of clean engine oil prior to installation.
3. Install valve lifter (9) into the cylinder head.
Note: Refer to Specifications, "Valve Mechanism".
Inlet and Exhaust Valve Guides
Table 1
Required Tools
Tool Part Number Part Description Qty
E
7M-3975 Valve Guide Driver 1
5P-1729 Valve Guide Bushing 1
NOTICE
2/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Use new valve guides for assembly.
1. Coat the outside of the valve guides with clean engine oil prior to installation.
2. Use Tooling (E) and a suitable press to install the valve guides. The valve guide must
extend 26.0 ± 0.50 mm (1.02 ± 0.020 inch) above the surface of the cylinder head.
Inlet and Exhaust Valve Seat Inserts
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1P-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Use new inserts for assembly.
1. Lower the temperature of the valve seat inserts. Install the valve seat inserts with Tooling
(F).
Bridge Dowels
Table 3
Required Tools
Tool Part Number Part Description Qty
G 6V-4009 Dowel Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g01051069
Note: Use new dowels for assembly. Refer to Service Magazine, SEPD1825, "New
Cylinder Head Groups and Valve Mechanisms" for the correct procedure.
1. Use Tooling (G) with a hammer to install bridge dowels (8). The bridge dowels must extend
66.5 ± 0.50 mm (2.62 ± 0.020 inch) above the surface of the cylinder head.
Inlet and Exhaust Valves
Table 4
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
4/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g00618922
If the valve locks are not positioned correctly, the locks can be expelled
when the spring pressure is released.
To help prevent personal injury, stay away from the front of the valve
retainer and springs. Ensure that the valve locks are positioned
correctly.
Note: Do not reuse valve rotocoils.
1. Coat valves (7) with clean engine oil. Install the valves into the cylinder head.
2. Install seal (6), inner spring (4), outer spring (5), and valve rotocoil (3) over the valve stem
and the valve guide.
3. Compress the valve spring with Tooling (A) and install retainer lock (2).
4. Release the pressure on Tooling (A). Remove Tooling (A). Lightly tap the top of the valve
with a hammer tol ensure that the retainer locks are in the proper position.
5/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 5. Repeat Steps 1 through 4 for the remaining valves.
End By:
a. Install the cylinder head.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Feb 22 09:54:54 UTC+0800 2020
6/6
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11N TRACK-TYPE TRACTOR 4HK
Configuration: D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY 3508 Engine
Disassembly and Assembly
3500 and 3500B High Displacement Engines for Caterpillar Built Machines
Media Number -SENR1126-33 Publication Date -01/07/2015 Date Updated -14/09/2018
i07511232
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the spacer plate and the surface of the cylinder block are clean.
1/7
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01053983
2. Install the O-ring seal on dowel (14).
Illustration 2 g01053978
NOTICE
Ensure that the surface of the spacer plate gasket and the surface of
the cylinder block are clean. Do not use a gasket adhesive on these
surfaces.
3. Install a new gasket (13) on the dowels in the cylinder block.
Illustration 3 g01053977
4. Install spacer plate (12) on the dowels.
5. Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner
Projection" for the correct procedure.
2/7
D11N Track-Type Tractor Power Shift 4HK00001-UP (MACHINE) POWERED BY ...
2020/2/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...