This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i04499449
Auxiliary Drive (Front) - Disassemble
SMCS - 1207-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B
8B-7551 Bearing Puller 1
7S-9154 Step Plate 1
C 1P-1863 Retaining Ring Pliers 1
D 1P-1861 Retaining Ring Pliers 1
E 248-3310 Spanner Wrench 1
Start By:
a. Remove the auxiliary drive.
1/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g02679656
1. Remove nuts (1) and the washers. Remove studs (2).
Illustration 2 g02679676
2. Use Tooling (A) to remove pulley (3).
Illustration 3 g02679696
2/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g02679717
3. Loosen nut (4).
4. Use a press and Tooling (B) to loosen gear (5) from the shaft.
5. Remove nut (4) and remove gear (5).
Illustration 5 g02679777
6. Use Tooling (C) to remove retaining ring (6). Remove bearing (7) from gear (5).
Illustration 6 g02679882
7. Remove O-ring seal (10). Use Tooling (D) to remove retaining ring (8). Remove shaft (9).
3/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 7 g02680020
8. Use Tooling (E) to remove locknut (11). Remove lockwasher (12) and remove bearing (13).
Illustration 8 g02680056
9. Remove lip seal (14). Note the orientation of the lip seal for installation purposes.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:54:29 UTC+0800 2020
4/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i05802882
Auxiliary Drive (Front) - Assemble
SMCS - 1207-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1P-1863 Retaining Ring Pliers 1
D 1P-1861 Retaining Ring Pliers 1
E 248-3310 Spanner Wrench 1
F 1P-0510 Driver 1
Illustration 1 g02680056
Note: Note the orientation of the lip seal, illustrated above, for installation.
1/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 1. Use Tooling (F) to install lip seal (14). Lubricate the lip with the lubricant that is being
sealed.
Illustration 2 g02680020
2. Install bearing (13). Install lockwasher (12).
3. Install locknut (11). Use Tooling (E) to torque the locknut to 108 ± 7 N·m (80 ± 5 lb ft). If
necessary, increase the torque to align the slots.
Illustration 3 g02679882
4. Install shaft (9). Use Tooling (D) to install retaining ring (8).
5. Lubricate the bore for O-ring seal (10) with the lubricant that is being sealed. Install O-ring
seal (10).
2/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 4 g02679777
6. Install bearing (7) onto gear (5).
7. Use Tooling (C) to install retaining ring (6).
Illustration 5 g02679696
8. Install gear (5)
9. Install nut (4). Tighten nut (4) to a torque of 290 ± 10 N·m (214 ± 7 lb ft). Tap the gear
down with a hammer and torque nut (4) again to a torque of 290 ± 10 N·m (214 ± 7 lb ft).
Illustration 6 g03676295
3/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 10. Measure the distance from the end of housing (15) to bearing (7). Dimension (X) is
6.6 ± 0.5 mm (0.26 ± 0.02 inch).
Illustration 7 g02681817
11. Install pulley (3).
12. Install studs (2). Tighten studs (2) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
13. Install the washers and install nuts (1). Tighten nuts (1) to a torque of 47 ± 9 N·m
(35 ± 7 lb ft).
End By:
a. Install the auxiliary drive.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:55:24 UTC+0800 2020
4/4(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i02293132
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01147941
1/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 1. Remove bolts (1) and valve mechanism covers (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01147941
1. Position valve mechanism covers (2) on the valve mechanism cover base. Install bolts (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:56:20 UTC+0800 2020
2/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i03424280
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g01147965
1. Remove tube assemblies (1).
2. Disconnect harness assemblies (5) and harness assembly (2).
3. Remove bolts (4).
4. Remove valve mechanism cover base (3) and the seal from the cylinder head.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 2 g01147965
1. Install the seal on valve mechanism cover base (3).
2. Position valve mechanism cover base (3) on the cylinder head and install bolts (4).
3. Position harness assemblies (5) on the electronic unit injectors. Tighten the cap nuts to a
torque of 2.5 ± 0.25 N·m (22 ± 2 lb in).
4. Connect harness assembly (2).
5. Install tube assemblies (1).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:57:16 UTC+0800 2020
3/3(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i07011948
Rocker Arm and Shaft - Remove
SMCS - 1102-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 387-8004 Lifting Bracket 1
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g01148045
1. Remove bolts (2).
2. Use Tooling (A) to remove rocker arm shaft assembly (4), valve rocker arms (3), and
electronic unit injector rocker arms (1) as a unit.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:58:12 UTC+0800 2020
2/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i04997049
Rocker Arm - Disassemble
SMCS - 1123-015
Disassembly Procedure
Start By:
a. Remove the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 1 g01047557
1. Remove valve rocker arms (11) and electronic unit injector rocker arm (3) from rocker shaft
assembly (4).
2. Remove jam nut (7) from adjustment screw (8).
3. Remove adjustment screw (8) from valve rocker arms (11).
4. Remove button (10) from adjustment screw (8). Remove O-ring seal (9) from the
adjustment screw.
5. Remove jam nut (2) from unit injector adjustment screw (1).
6. Remove unit injector adjustment screw (1) from electronic unit injector rocker arm (3).
7. Remove button (6) from unit injector adjustment screw (1). Remove O-ring seal (5) from
the unit injector adjustment screw.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 22:59:07 UTC+0800 2020
2/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i04998150
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01047557
1/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Note: Do not reuse the O-ring seal on the adjustment screw if the button is removed from
the adjustment screw.
1. Install O-ring seal (9) in button (10).
2. Use a soft hammer to seat button (10) on adjustment screw (8).
3. Install adjustment screw (8) in valve rocker arms (11). Install jam nut (7) on the adjustment
screw.
4. Install O-ring seal (5) in button (6).
5. Use a soft hammer to seat button (6) on unit injector adjustment screw (1).
6. Install unit injector adjustment screw (1) in electronic unit injector rocker arm (3). Install
jam nut (2) on the unit injector adjustment screw.
7. Lubricate rocker shaft assembly (4) with clean engine oil.
8. Install valve rocker arms (11) and electronic unit injector rocker arm (3) on rocker shaft
assembly (4).
End By:
a. Install the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 23:00:03 UTC+0800 2020
2/2(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i07399513
Rocker Arm and Shaft - Install
SMCS - 1102-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 387-8004 Lifting Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 1 g01148045
Illustration 2 g01325993
1. Position rocker arm shaft assembly (4), valve rocker arms (3), and electronic unit injector
rocker arms (1) as a unit with Tooling (A) on the cylinder head.
2/3(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Note: Apply clean engine oil to the underside of the bolt heads and the threads prior to
installation.
2. Install bolts (2) and tighten to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Tighten bolts (2) again
to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Turn bolts (2) for an additional 60 ± 5 degrees.
Tighten the bolts in the following sequence: 2, 3, 1, 4.
Note: The additional 60 degrees can be attained by turning the bolt two points.
3. Adjust the valve lash for the inlet valves and the exhaust valves. Refer to Testing and
Adjusting, "Engine Valve Lash - Inspect/Adjust".
4. Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit
Injector - Adjust".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 23:00:59 UTC+0800 2020
3/3(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C27 INDUSTRIAL ENGINE TWM
Configuration: C27 Industrial Engine TWM00001-UP
Disassembly and Assembly
C27 and C32 Industrial Engines
Media Number -RENR9577-06 Publication Date -01/11/2017 Date Updated -20/11/2017
i02446003
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1U-9200 Lever Puller Hoist 1
Start By:
a. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
b. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
c. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/7(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the rear gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01222228
2. Remove cover (1).
2/7(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 2 g01222230
3. Remove bolts (2) and gear (3).
Illustration 3 g01222233
4. Remove bolts (4), thrust plate (5), and adapter assembly (6).
3/7(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 4 g01222234
5. Use bolt (4) in order to remove sealing plate (7). Remove the O-ring seals.
Illustration 5 g01148246
6. Remove elbow (8). Disconnect hose assembly (9).
4/7(W)
w
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...