This document provides instructions for removing and installing the front gear group of a C18 industrial engine. The removal procedure involves taking off 15 parts in 8 steps, including bolts, plates, gears, and seals. The installation procedure instructs to thoroughly clean parts, apply thread locking compounds, and install the front gear group in the reverse order of removal, noting the parts must be timed correctly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjkskedmme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
This document provides instructions for disassembling the planetary transmission of a C18 industrial engine. It outlines 19 steps including removing the torque converter housing, pump, cover, and springs. Tools include an engine stand, lifting eyes, and a spring compressor. Videos are available to demonstrate procedures by accessing a Caterpillar website. Keeping components clean and replacing worn seals and gaskets is emphasized.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 ...fjkskedmme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions that fluids must be contained to prevent contamination. The procedure describes detaching hoses, loosening bolts, and using lifting equipment to remove the heavy travel motor assembly.
Caterpillar cat 345 c excavator (prefix rfn) service repair manual (rfn00001 ...fjkskedmme
This document provides instructions for removing and installing engine components on a 345C Excavator, including:
- Valves, guides, and seat inserts
- The engine oil filter base
- Disassembling and assembling the oil filter base
The procedures include required tools and safety notices. Illustrations show the components and numbered steps to remove and install parts, ensuring proper assembly of spring-loaded components.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure involving 5 steps of disconnecting components and identifying parts.
This document provides instructions for disassembling the planetary transmission of a C18 industrial engine. It outlines 19 steps including removing the torque converter housing, pump, cover, and springs. Tools include an engine stand, lifting eyes, and a spring compressor. Videos are available to demonstrate procedures by accessing a Caterpillar website. Keeping components clean and replacing worn seals and gaskets is emphasized.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, seals, springs, and pistons.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat 336 f lxe excavator (prefix naj) service repair manual (naj00...fjkskedmme
The document provides instructions for disassembling the travel motor of a 336F XE or 336F LXE excavator. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Precautions are provided to safely release spring forces and properly mark parts for reassembly. Tools required include various bolts, pins, adapters, and pullers to dismantle the motor.
Caterpillar cat 336 f excavator (prefix wcf) service repair manual (wcf00001 ...fjkskedmme
The document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 336 f l excavator (prefix kcs) service repair manual (kcs0000...fjkskedmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and replacing gaskets and seals before reinstalling parts in the reverse order of removal. Safety precautions are provided regarding preventing contamination, allowing components to cool, and using approved lubricants.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp0...fjkskedmme
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, pistons, barrel assembly, friction plates and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their original positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain any released fluids.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...fksjksmmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by having the technician remove the final drive assembly and place it on a transmission repair stand. Detailed steps are then provided to disassemble the various components of the final drive including removing gears, shafts, carriers, and housing pieces. The final section provides instructions for reassembling the final drive, making sure to clean all parts and replace any damaged seals. Technicians are instructed to properly set the bearing preload when reinstalling components.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine. It describes how to remove and install the auxiliary drive, valve mechanism covers, valve mechanism cover base, rocker arms and shafts. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety notices are provided to keep parts clean and prevent contamination.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, seals, springs, and pistons.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat 336 f lxe excavator (prefix naj) service repair manual (naj00...fjkskedmme
The document provides instructions for disassembling the travel motor of a 336F XE or 336F LXE excavator. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Precautions are provided to safely release spring forces and properly mark parts for reassembly. Tools required include various bolts, pins, adapters, and pullers to dismantle the motor.
Caterpillar cat 336 f excavator (prefix wcf) service repair manual (wcf00001 ...fjkskedmme
The document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 336 f l excavator (prefix kcs) service repair manual (kcs0000...fjkskedmme
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and replacing gaskets and seals before reinstalling parts in the reverse order of removal. Safety precautions are provided regarding preventing contamination, allowing components to cool, and using approved lubricants.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 330 f ln excavator (prefix wba) service repair manual (wba000...fksjksmmde
The document provides step-by-step instructions to disassemble a travel motor. It begins by listing required tools and fasteners. The procedures then describe how to remove 27 components of the travel motor including the head assembly, housing assembly, brake piston, rotating group, pistons, and seals. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp0...fjkskedmme
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, pistons, barrel assembly, friction plates and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their original positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain any released fluids.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...fksjksmmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by having the technician remove the final drive assembly and place it on a transmission repair stand. Detailed steps are then provided to disassemble the various components of the final drive including removing gears, shafts, carriers, and housing pieces. The final section provides instructions for reassembling the final drive, making sure to clean all parts and replace any damaged seals. Technicians are instructed to properly set the bearing preload when reinstalling components.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine. It describes how to remove and install the auxiliary drive, valve mechanism covers, valve mechanism cover base, rocker arms and shafts. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety notices are provided to keep parts clean and prevent contamination.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tube assemblies, harness assemblies, and bolts then installing seals, bases and assemblies.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and detailed step-by-step procedures with accompanying illustrations.
3) Special notes are provided regarding keeping parts clean, inspecting components, and not using lubricants during certain installation procedures.
Similar to Caterpillar cat c18 industrial engine (prefix wrh) service repair manual (wrh00001 and up) (20)
Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 ...cfvdssd
This document provides instructions for removing and installing the rear gear group and flywheel on a 345C Excavator. It describes:
1) Using various tools to remove 14 individual components of the rear gear group, including gears, seals, bolts, and bearings.
2) Proper installation of each part, ensuring correct positioning, torque specifications, and temperatures for seals and bearings.
3) Removing the flywheel using a lifting device and guide stud after removing bolts.
4) Installing the ring gear on the flywheel by heating and seating it, then attaching the flywheel using loctite on the bolts.
Caterpillar cat 336 f xe excavator (prefix pfl) service repair manual (pfl000...cfvdssd
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
Caterpillar cat 336 f xe excavator (prefix naj) service repair manual (naj000...cfvdssd
The document provides instructions for disassembling a travel motor with 27 steps. It begins by fastening the travel motor vertically and removing the head from the body. Several internal components are then removed, including seals, springs, pistons, and bearings. Tools required include retaining ring pliers, a bearing puller, bolts, and an eyebolt. The motor head assembly is detached last by attaching an eyebolt and lifting device.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...cfvdssd
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
Caterpillar cat 336 f lxe excavator (prefix naj) service repair manual (naj00...cfvdssd
The document provides instructions for disassembling a travel motor with 27 steps. It begins by fastening the travel motor vertically and removing the head from the body. Several internal components are then removed, including seals, springs, pistons, and bearings. Tools required include retaining ring pliers, a bearing puller group, and an adapter. The instructions note to mark components' positions and take care when removing parts.
Caterpillar cat 336 f ln xe excavator (prefix ybh) service repair manual (ybh...cfvdssd
This document provides instructions for disassembling the travel motor on 336F LNXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, relief valves, plugs and O-rings. Special care must be taken when removing components under spring pressure. Various tools are required including bolts, pins and a bearing puller to dismantle the travel motor into individual parts for repair or replacement.
Caterpillar cat 336 f ln xe excavator (prefix mtw) service repair manual (mtw...cfvdssd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar cat 336 f ln xe excavator (prefix ltp) service repair manual (ltp...cfvdssd
This document provides instructions for disassembling the travel motor on a 336F L XE excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, spool assembly, springs, seals, plates, and bearings. Various tools are required, and safety precautions are provided to release spring forces. The detailed process is described through illustrations and text to correctly take apart the travel motor.
Caterpillar cat 336 f ln xe excavator (prefix kgh) service repair manual (kgh...cfvdssd
This document provides instructions for disassembling the travel motor on a 336F L XE excavator. It outlines 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and more. Various tools are required including bolts, pins, pullers and stands to safely remove components while releasing spring forces. Detailed illustrations accompany each step to clearly show how to disassemble the travel motor.
Caterpillar cat 336 f ln xe excavator (prefix dfy) service repair manual (dfy...cfvdssd
The document provides instructions for servicing components of a Caterpillar C9.3 engine, including removing and installing the camshaft, cylinder head, rocker arm assembly, and lifter group. The procedures describe cleaning parts, using specific tools, aligning timing marks, applying lubricant, and torquing bolts to specifications.
Caterpillar cat 336 f ln excavator (prefix wcf) service repair manual (wcf000...cfvdssd
The document provides instructions to disassemble a 336F excavator travel motor. It describes 27 steps to remove parts like the head, springs, pistons, bearings, seals and more. Various tools are required including bolts, pins, pullers and pliers. Safety precautions are noted to avoid injury from released springs. Detailed illustrations accompany each step.
Caterpillar cat 336 f ln excavator (prefix tje) service repair manual (tje000...cfvdssd
The document provides instructions for disassembling the travel motor on an excavator model 336F. It describes 27 steps to remove parts like the motor head assembly, port plate, springs, pistons, bearings, seals and other components. Various tools are required including bolts, pins, pullers, pliers and an adapter to securely disassemble the motor while releasing pressures and tensions safely. Detailed illustrations accompany each step to ensure correct part removal and placement during reassembly.
Caterpillar cat 336 f ln excavator (prefix ljy) service repair manual (ljy000...cfvdssd
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f ln excavator (prefix kcs) service repair manual (kcs000...cfvdssd
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures describe disconnecting electrical connections and fluid lines, removing mounting hardware, and installing replacement parts in the reverse order of removal, taking care to clean parts and apply thread sealant or anti-seize as specified. Safety precautions are provided regarding working on hot or high-voltage components and preventing fluid contamination.
Caterpillar cat 336 f l xe excavator (prefix ybh) service repair manual (ybh0...cfvdssd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, and swashplate. Special tools are required to remove parts and release spring forces safely. Component positions must be marked for proper reassembly.
Caterpillar cat 336 f l xe excavator (prefix mtw) service repair manual (mtw0...cfvdssd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp0...cfvdssd
This document provides instructions for disassembling the travel motor on a 336F L XE excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, spool assembly, springs, seals, plates, and bearings. Various tools are required, and safety precautions are provided to release spring forces. The detailed process is described through illustrations and text to correctly take apart the travel motor.
Caterpillar cat 336 f l xe excavator (prefix kgh) service repair manual (kgh0...cfvdssd
This document provides instructions for disassembling the travel motor on a 336F L XE excavator. It outlines 27 steps to remove parts like the motor head assembly, springs, seals, relief valves, plugs and more. Various tools are required including a driver group, bearing puller group, retaining ring pliers and more. Safety precautions are provided to be aware of parts propelled by spring forces during disassembly.
Caterpillar cat 336 f l xe excavator (prefix dfy) service repair manual (dfy0...cfvdssd
The document provides instructions for removing and installing camshafts on Caterpillar C9.3 engines. It describes:
1. Using a hook tool to remove the 12 valve lifters and camshaft, marking the lifters for installation.
2. Cleaning and lubricating the components before installing the camshaft and valve lifters back in their original locations using the hook tool.
3. The document is part of a service manual for 336F L XE and 336F LN XE excavators.
Caterpillar cat 336 f l excavator (prefix wcf) service repair manual (wcf0000...cfvdssd
The document provides instructions to disassemble a 336F excavator travel motor. It describes 27 steps to remove parts like the head, springs, pistons, bearings, seals and more. Various tools are required including bolts, pins, pullers and other equipment to safely remove parts and release spring forces during the process. The goal is to fully disassemble the travel motor for repair or replacement of components.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WRH
Configuration: C18 Industrial Engine WRH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i03203779
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
D 5P-1733 Seal Locator 1
E 5P-1737 Bolt 3
F 9S-8858 Nut (Seal Installer) 1
G 6V-6142 Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the
crankshaft front seal and the wear sleeve are separated, these components cannot be used again.
Note: Do not use any type of lubricant during the installation of the crankshaft front seal
and the wear sleeve.
1. Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft
for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to
1/3(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. an out of round condition. Use a polishing cloth in order to remove any imperfections on the
crankshaft.
2. Clean the outside diameter of the crankshaft.
Illustration 1 g01635160
3. Fasten Tooling (D) to the crankshaft with Tooling (E).
Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft
rotation toward the front of the engine.
4. Position wear sleeve (2) and crankshaft front seal (1) on Tooling (D). Install Tooling (G) on
Tooling (D). Lubricate the face of the washer on Tooling (F). Install Tooling (F) on Tooling
(D).
5. Tighten Tooling (F) until Tooling (G) contacts Tooling (D).
6. Remove Tooling (F) and Tooling (G) from Tooling (D).
7. Remove Tooling (E) and Tooling (D) from the crankshaft.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
2/3(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WRH
Configuration: C18 Industrial Engine WRH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i04275771
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01100930
1/2(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 1. Remove button head screws (3).
2. Remove nuts (7) and washers (6) from studs (4).
3. Remove front cover (2) from front housing (1).
4. Remove O-ring seal (5) from studs (4).
5. Remove seal (8) from front cover (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 12:30:45 UTC+0800 2020
2/2(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WRH
Configuration: C18 Industrial Engine WRH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i04275789
Front Cover - Install
SMCS - 1166-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 1 g01268777
1. If studs (4) are loose or the threads are damaged, install new studs in front housing (1).
Apply Tooling (A) to the threads of the studs. Install the studs in the front housing. Install O
-ring seal (5) on the studs.
2. Install seal (8) in front cover (2).
3. Install front cover (2) on studs (4). Install washers (6) and nuts (7).
4. Install button head screws (3). Tighten the button head screws to a torque of 21 ± 3 N·m
(15 ± 2 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 12:31:40 UTC+0800 2020
2/2(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WRH
Configuration: C18 Industrial Engine WRH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02721549
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
b. Remove the air compressor, if necessary. Refer to Disassembly and Assembly, "Air
Compressor - Remove and Install".
c. Remove the water pump, if necessary. Refer to Disassembly and Assembly, "Water Pump -
Remove".
d. Remove the auxiliary water pump, if necessary. Refer to Disassembly and Assembly,
"Auxiliary Water Pump - Remove".
e. Remove the fuel transfer pump, if necessary. Refer to Disassembly and Assembly, "Fuel
Transfer Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Note: Be sure to mark the orientation of each of the gears for installation purposes.
Illustration 1 g01008429
1. Remove bolts (2) and thrust plate (1).
2/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g01008430
2. Remove sealing plate (3) and adapter (4).
Illustration 3 g01008431
3. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 4 g01101536
4. Remove bolts (8), plate (9), and adjustable idler gear assembly (7).
5. Use Tooling (A) and remove the sleeve bearing from adjustable idler gear assembly (7).
4/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 5 g01101045
6. Remove bolts (11), plate (12), and idler gear assembly (10).
7. Use Tooling (A) and remove the sleeve bearing from idler gear assembly (10).
5/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 6 g01101048
8. Remove bolts (14), plate (15), and cluster gear assembly (13).
9. Use Tooling (A) and remove the sleeve bearing from cluster gear assembly (13).
6/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 7 g01101050
Note: Stub shaft assembly (16) must be removed in order to remove plate (22). The
backlash for the camshaft gear and the adjustable idler gear assembly will need to be
readjusted at assembly.
10. Remove nuts (17) and remove stub shaft assembly (16).
Note: Stub shaft (18) must be removed in order to remove plate (22).
11. Remove nuts (19) and remove stub shaft (18).
12. Remove bolts (21) and remove stub shaft (20).
13. Remove locking bolts (23) that hold plate (22) to the cylinder block. Remove plate (22).
14. If studs (24) are loose or the threads are damaged, remove the studs from the front plate.
7/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 8 g01101052
15. Remove integral seal (25) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 12:32:36 UTC+0800 2020
8/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WRH
Configuration: C18 Industrial Engine WRH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i05884214
Gear Group (Front) - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 8T-2998 Lubricant -
C - Loctite 5900 -
D - Loctite 243 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 1. Thoroughly clean the gasket material from the cylinder block and both sides of the plate.
Illustration 1 g01101567
2. If studs (24) are loose or the threads are damaged, install new studs (24) in the front plate.
Apply Tooling (D) to the serrations of studs (24). Install studs (24) in the front plate.
3. Install integral seal (25) on the dowel pins on the cylinder block.
Note: Apply Tooling (C) to the bottom of integral seal (25) in order to fill the space at the
cylinder block, the front housing, and the engine oil pan.
4. Install plate (22) on the dowel pins on the cylinder block. Install new locking bolts (23)
(Marked "X") in order to fasten the front plate to the cylinder block. Tighten locking bolts
(23) to a torque of 55 N·m (41 lb ft).
Note: Clean the old sealant from the bolts and apply Tooling (D) to the bolts.
5. Tighten locking bolts (23) again to a torque of 55 N·m (41 lb ft).
2/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g01101565
6. Install stub shaft (18). Apply Tooling (D) to the studs and the bolt for stub shaft (18).
Tighten nuts (19) and the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
7. Install stub shaft assembly (16). Apply Tooling (D) to the studs and the bolt for stub shaft
assembly (16). Do not tighten nuts (17) and the bolt for stub shaft assembly (16) at this
time. Nuts (17) and the bolt for stub shaft assembly (16) will need to be tightened when the
backlash is adjusted.
8. Adjust the backlash between the camshaft gear and the adjustable idler gear assembly. The
backlash should be 0.3556 ± 0.254 mm (0.014± 0.010 inch). Refer to Testing and Adjusting,
"Gear Group (Front) - Time" for the backlash adjustment procedure. Tighten nuts (17) and
the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
9. Install stub shaft (20). Apply Tooling (D) to bolts (21). Install bolts (21) and tighten in a
numeric sequence 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1 to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
3/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 3 g01101161
10. Use Tooling (A) to install the sleeve bearing in cluster gear assembly (13).
11. Put cluster gear assembly (13) on the stub shaft. Ensure that Timing Marks (V) are aligned
on the cluster gear assembly and the crankshaft gear.
12. Position plate (15) with the oil groove toward the face of the gear. Apply Tooling (D) to
bolts (14). Install bolts (14). Tighten bolts (14) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
4/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 4 g01101045
13. Use Tooling (A) to install the sleeve in idler gear assembly (10).
14. Put idler gear assembly (10) on the stub shaft. Install plate (12) with the oil groove toward
the gear face. Apply Tooling (D) to bolts (11). Install bolts (11). Tighten bolts (11) to a
torque of 30 ± 7 N·m (22 ± 5 lb ft).
5/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 5 g01008436
15. Use Tooling (A) to install the sleeve bearing in adjustable idler gear assembly (7).
Note: Align the oil hole in the bearing with the oil hole in the adjustable idler gear
assembly.
16. Put adjustable idler gear assembly (7) on the stub shaft assembly. Position plate (9) with the
oil groove toward the face of the gear. Apply Tooling (D) to bolts (8). Install bolts (8).
Tighten bolts (8) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
Note: Check the backlash for the camshaft gear and the adjustable idler gear assembly. The
camshaft gear must be installed and the adjustable idler gear assembly must be removed in
order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear
Group (Front) - Time".
6/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 6 g01008431
17. Install O-ring seal (5) and O-ring seal (6) in sealing plate (3). Lubricate O-ring seal (6) with
a 50/50 mixture of Tooling (B) and clean engine oil.
Illustration 7 g01008430
7/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 8 g01010256
18. Install adapter (4). Ensure that the dowel in the adapter engages the hole in the camshaft.
19. Install sealing plate (3) and thrust plate (1). Ensure that the dowel in the adapter engages the
hole in the thrust plate. Apply Tooling (D) to bolts (2). Install bolts (2). Evenly tighten bolts
(2) in order to ensure that sealing plate (3) and O-ring seal (5) are seated against the cylinder
head.
20. Adjust the backlash for the camshaft gear and the adjustable idler gear, if necessary. Refer
to Testing and Adjusting, "Gear Group (Front) - Time".
Note: The camshaft gear must be installed and the adjustable idler gear must be removed in
order to perform the backlash adjustment procedure.
End By:
a. Install the fuel transfer pump, if necessary. Refer to Disassembly and Assembly, "Fuel
Transfer Pump - Install".
b. Install the auxiliary water pump, if necessary. Refer to Disassembly and Assembly,
"Auxiliary Water Pump - Install".
c. Install the water pump, if necessary. Refer to Disassembly and Assembly, "Water Pump -
Install".
d. Install the air compressor, if necessary. Refer to Disassembly and Assembly, "Air
Compressor - Remove and Install".
e. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 12:33:32 UTC+0800 2020
8/8(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WRH
Configuration: C18 Industrial Engine WRH00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02164241
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
c. Remove the air compressor, if equipped. Refer to Disassembly and Assembly, "Air
Compressor - Remove".
d. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
e. Remove the engine support. Refer to Disassembly and Assembly, "Engine Support (Front) -
Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/4(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Illustration 1 g01097597
2/4(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 1. Remove bolts (1).
2. Remove bolts (2) and bracket (3).
3. Remove nut (4).
4. Remove bolts (5).
Note: It is not necessary to remove fuel transfer pump (6) and the adapter.
Illustration 2 g01097924
5. Remove bolts (7) and strap (8).
6. Remove bolt (10) and nut (9).
7. Remove bolts (12).
8. Remove nuts (11).
9. Remove bolts (14) that fasten the engine oil pan to the front housing.
Note: It is not necessary to remove the engine oil pan from the engine.
10. Remove front housing (13).
11. Remove gasket (15) from the plate and the front housing.
3/4(W)
w
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...