This document provides disassembly instructions for a 980H wheel loader torque converter in 3 sentences:
It outlines 56 steps to disassemble the individual components of the torque converter like removing bolts, gears, bearings, seals, and other parts using various tools like push-pullers, bearing pullers, and presses. The purpose is to take the torque converter fully apart in order to service or replace components like bearings, seals, and other wear items. Detailed illustrations accompany each step to show how to remove each part from the torque converter.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It lists over 50 steps to fully disassemble the component, removing individual parts like bearings, seals, gears, and housings. It then provides over 20 steps for reassembling the component, instructing the installer to clean all parts thoroughly and apply oil before assembling using various tools. The document is intended to guide maintenance technicians in servicing this drivetrain component.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for the freewheel stator component of the torque converter in a 980H wheel loader. It includes 56 steps to fully disassemble the component, listing all required tools. It also provides assembly instructions, noting the importance of cleanliness and applying oil to bearings before reassembly.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader. The disassembly section describes 55 steps to fully disassemble the torque converter into individual components. These include removing bolts, gears, seals, bearings and other parts. The assembly section then describes 11 steps to reassemble components such as installing bearings, seals, gears and housing pieces using various tools.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader model 9CM powered by a 3406C engine. It describes 55 steps to disassemble the torque converter and its components like gears, bearings, seals, housing, and provides diagrams. It also describes required tools and cleaning/inspection instructions for reassembly.
This document provides disassembly instructions for a 988H wheel loader torque converter in 3 sentences:
It begins by listing the required tools and parts needed for disassembly. The instructions then describe each step to disassemble the individual components of the torque converter such as removing bolts, seals, bearings, and other parts from the housing, turbine, impeller, shaft, and adapter. Proper lifting equipment is recommended for removing heavy internal components weighing up to 545 kg.
This document provides disassembly instructions for a 988H wheel loader torque converter in 3 sentences:
It begins by listing the required tools and parts needed for disassembly. The instructions then describe each step to disassemble the individual components of the torque converter such as removing bolts, seals, bearings, and other parts from the housing, turbine, impeller, shaft, and adapter. Proper lifting equipment is recommended for removing heavy internal components weighing up to 545 kg.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing, turbine, carrier assembly, impeller, adapter assembly, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and accompanying illustrations to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed tools and equipment are specified at each step to safely complete the disassembly process.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and accompanying illustrations to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed tools and equipment are specified at each step to safely complete the disassembly process.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This document provides disassembly instructions for a 988H wheel loader torque converter in 3 sentences:
It begins by listing the required tools and parts needed for disassembly. The instructions then describe each step to disassemble the individual components of the torque converter such as removing bolts, seals, bearings, and other parts from the housing, turbine, impeller, shaft, and adapter. Proper lifting equipment is recommended for removing heavy internal components weighing up to 545 kg.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 17 tools required. The assembly procedure lists the same tools and provides instructions to reassemble the components in reverse order.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, providing illustrations and required tools for each step.
3. The components include housing, gears, seals, bearings, plates, disks, and an impeller that must be carefully disassembled and reassembled.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
This document provides instructions for disassembling the components of a 988K wheel loader torque converter. It lists over 60 individual steps to remove parts like the housing assembly, shaft assembly, carrier assembly, impeller, piston, seals, bearings, and other internal components. Detailed illustrations accompany each step. Special tools are required to separate certain components, and safety precautions are noted due to the heavy weight of assemblies that need to be lifted out.
This document provides disassembly instructions for a 986H wheel loader transmission planetary system in 3 sentences or less:
The document outlines 75 steps to disassemble the transmission planetary system, removing components like planetary gears, clutch housings, pistons, seals, and other parts. Tools required include a transmission repair stand, eyebolts, clamps, retaining ring pliers, external pliers, drivers, and other specialized tools to aid in disassembly. Cleanliness is emphasized as dirt could enter the transmission during disassembly.
More Related Content
Similar to Caterpillar Cat 980H Wheel Loader (Prefix MHG) Service Repair Manual (MHG00001 and up).pdf
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader. The disassembly section describes 55 steps to fully disassemble the torque converter into individual components. These include removing bolts, gears, seals, bearings and other parts. The assembly section then describes 11 steps to reassemble components such as installing bearings, seals, gears and housing pieces using various tools.
This document provides disassembly and assembly instructions for a torque converter in a 980G wheel loader model 9CM powered by a 3406C engine. It describes 55 steps to disassemble the torque converter and its components like gears, bearings, seals, housing, and provides diagrams. It also describes required tools and cleaning/inspection instructions for reassembly.
This document provides disassembly instructions for a 988H wheel loader torque converter in 3 sentences:
It begins by listing the required tools and parts needed for disassembly. The instructions then describe each step to disassemble the individual components of the torque converter such as removing bolts, seals, bearings, and other parts from the housing, turbine, impeller, shaft, and adapter. Proper lifting equipment is recommended for removing heavy internal components weighing up to 545 kg.
This document provides disassembly instructions for a 988H wheel loader torque converter in 3 sentences:
It begins by listing the required tools and parts needed for disassembly. The instructions then describe each step to disassemble the individual components of the torque converter such as removing bolts, seals, bearings, and other parts from the housing, turbine, impeller, shaft, and adapter. Proper lifting equipment is recommended for removing heavy internal components weighing up to 545 kg.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing, turbine, carrier assembly, impeller, adapter assembly, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and accompanying illustrations to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed tools and equipment are specified at each step to safely complete the disassembly process.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and accompanying illustrations to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed tools and equipment are specified at each step to safely complete the disassembly process.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This document provides disassembly instructions for a 988H wheel loader torque converter in 3 sentences:
It begins by listing the required tools and parts needed for disassembly. The instructions then describe each step to disassemble the individual components of the torque converter such as removing bolts, seals, bearings, and other parts from the housing, turbine, impeller, shaft, and adapter. Proper lifting equipment is recommended for removing heavy internal components weighing up to 545 kg.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 17 tools required. The assembly procedure lists the same tools and provides instructions to reassemble the components in reverse order.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, providing illustrations and required tools for each step.
3. The components include housing, gears, seals, bearings, plates, disks, and an impeller that must be carefully disassembled and reassembled.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of the torque converter in a 980M wheel loader. It lists 46 steps to disassemble the components and 49 steps to reassemble them. Required tools include link brackets, push-pullers, bearing pullers, drivers, and retaining ring pliers. Detailed illustrations are provided to show each component and step in the process.
Similar to Caterpillar Cat 980H Wheel Loader (Prefix MHG) Service Repair Manual (MHG00001 and up).pdf (20)
This document provides instructions for disassembling the components of a 988K wheel loader torque converter. It lists over 60 individual steps to remove parts like the housing assembly, shaft assembly, carrier assembly, impeller, piston, seals, bearings, and other internal components. Detailed illustrations accompany each step. Special tools are required to separate certain components, and safety precautions are noted due to the heavy weight of assemblies that need to be lifted out.
This document provides disassembly instructions for a 986H wheel loader transmission planetary system in 3 sentences or less:
The document outlines 75 steps to disassemble the transmission planetary system, removing components like planetary gears, clutch housings, pistons, seals, and other parts. Tools required include a transmission repair stand, eyebolts, clamps, retaining ring pliers, external pliers, drivers, and other specialized tools to aid in disassembly. Cleanliness is emphasized as dirt could enter the transmission during disassembly.
This document provides disassembly instructions for the transmission planetary of a 986H wheel loader. It outlines 59 steps to fully disassemble the transmission, including removing planetary gears, clutch housings, pistons, seals, gears, and other components. Tools required include a transmission repair stand, eyebolts, clamps, retaining ring pliers, external pliers, drivers, and slide hammers. Detailed illustrations accompany each step. Safety precautions are provided to prevent injury from released spring forces.
This document provides assembly instructions for a torque converter in a 982M wheel loader. It outlines 51 steps to assemble the internal components of the torque converter and attach it to the transmission and output transfer gears. The instructions include installing seals, bearings, gears, plates, springs, and bolts. Tolerances and torque specifications are provided. The final step is to connect the assembled torque converter to the transmission and output transfer gears.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 982M Wheel Loader. It outlines 51 steps requiring various tools to install seals, bearings, gears, plates, and bolts in the specified order and torque. The process connects the assembled torque converter to the transmission and output transfer gears.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Finally, it explains how to separate the transmission from the output transfer gears by removing bolts, disconnecting lines, and lifting components with brackets.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps to install various components like seals, bearings, gears, and housings. Finally, it specifies connecting the assembled torque converter to the transmission and output transfer gears.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for a piston pump on a 980L wheel loader. It describes installing various components like bearings, seals, retainers and pistons. It also provides steps to determine proper shim thickness and clearance between parts. The goal is to assemble the pump with specified end play, sliding block play and timing between components.
The document provides step-by-step instructions for assembling a torque converter for a 980M wheel loader. It details 51 steps for installing various components like seals, bearings, gears, and housings. Proper tools and torque specifications are listed to ensure correct assembly.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other internal components. Detailed illustrations accompany each step to show how to properly disassemble the transmission in the correct order. Safety precautions are provided to warn of potential spring hazards during disassembly.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists over 50 individual steps to disassemble the various components of the torque converter housing assembly, including removing pumps, gears, seals, bearings, and other internal parts. Detailed illustrations accompany each step to show how to position the assembly, what tools are needed, and how to separate the individual components. The overall process involves disassembling the entire torque converter and transmission housing to access all internal parts.
This document provides instructions for disassembling the components of a 992K wheel loader torque converter. It describes removing over 20 individual parts in multiple steps, including the torque converter, modulating valves, pumps, gears, housings, clutches and bearings. Cleanliness is emphasized throughout to prevent contamination. Various tools are required and safety precautions mentioned due to components weighing up to 680kg.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions to remove components such as gears, seals, plates, discs, bearings, and clutches. Safety precautions are provided for releasing clutch springs. The disassembly process is described in detail through 50 steps and accompanied by illustrations of each step.
The document provides instructions for disassembling and assembling the vane pump used in the steering system of a 657G Wheel Scraper. It describes in detail removing each individual component of the pump including housing, seals, cartridge, rotor, vanes and shaft. Fifteen detailed steps are outlined for disassembly, requiring basic tools like retaining ring pliers and a bearing puller. Similarly, sixteen steps are provided for reassembling the pump and installing it back into the steering system. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
This document provides instructions for disassembling a torque converter for a 988K wheel loader. It lists over 60 individual steps to remove components such as housing assemblies, shafts, bearings, seals, gears, and plates. Special tools are required for tasks like separating housings and pulling components. Precautions include using lifting devices and cribbing due to component weights up to 545 kg. Detailed illustrations accompany each step.
This service repair manual provides instructions to disassemble the transmission planetary of a 986H wheel loader model. It outlines 57 steps to fully disassemble the transmission components, including removing planetary gears, clutch housings, pistons, seals, gears, and other parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided throughout to prevent injury from heavy parts or released spring forces during disassembly.
This document provides assembly instructions for a torque converter in 3 sentences or less:
The document outlines over 60 steps to assemble a torque converter for a 980H wheel loader, including installing various bearings, seals, gears, housings, and fasteners in the proper sequence and with specified torques. Precautions are provided to handle parts carefully and apply lubricants as needed during assembly. Tools required for the assembly process are also listed.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER MHG
Configuration: 980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine
Disassembly and Assembly
980H Wheel Loader Power Train
Media Number -RENR8667-08 Publication Date -01/09/2018 Date Updated -04/09/2018
i05903287
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B
8B-7548 Push-Puller 1
8B-7550 Leg 2
8H-0684 Ratchet Wrench 1
8B-7560 Step Plate 1
8H-0663 Bearing Puller Attachment 1
C
8B-7548 Push-Puller 1
8H-0684 Ratchet Wrench 1
8B-7549 Leg 2
5P-4808 Cap 2
8B-7554 Bearing Cup Puller Attachment 1
D
5F-7343 Bearing Puller Attachment 1
1P-0520 Driver Group 1
E 1P-0510 Driver Group 1
F 7
1/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Forcing Screw
3/8 - 16 x 3 in
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate" for the machine that is being serviced.
1. Place the torque converter housing assembly (2) on wood blocks.
Illustration 1 g00503225
2. Remove bolts (1) and the washers from torque converter housing assembly (2) .
Illustration 2 g01111329
3. Install Tooling (A) to torque converter housing assembly (2) , as shown. Attach a suitable
lifting device to Tooling (A) . The weight of housing assembly (2) is approximately 120 kg
(265 lb).
4. Use Tooling (F) to loosen housing assembly (2) from the torque converter.
2/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove housing assembly (2) from the torque converter.
Illustration 3 g00871317
6. Remove O-ring seal (3) from torque converter housing assembly (2) .
Illustration 4 g00871318
7. Remove bolts (4) and the washers from pump adapter (5) and torque converter housing
assembly (2) .
3/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00871264
8. Use Tooling (F) to remove pump adapter (5) from torque converter housing assembly (2) .
Illustration 6 g00871319
9. Use tooling (C) to remove bearing cup (6) , O-ring seal (8) , and shims (7) from pump
adapter (5) . See illustration 13 for Tooling (C) .
Illustration 7 g00871326
4/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 10. Remove pump drive gear (9) from torque converter housing assembly (2) .
Illustration 8 g00871451
11. Use Tooling (B) to remove bearing cones (10) from each side to pump drive gear (9) .
Illustration 9 g00871333
12. Use Tooling (C) to remove bearing cup (11) from torque converter housing assembly (2) .
See illustration 13 for Tooling (C) .
5/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01112900
13. Remove bolt (12) and the washer from torque converter housing assembly (2) .
14. Use Tooling (F) to push shaft assembly (14) out of torque converter housing assembly (2) .
15. Remove idler gear (13) from torque converter housing assembly (2) .
Illustration 11 g01112903
16. Remove O-ring seal (15) from shaft assembly (14) .
6/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00871365
17. Remove bearing cone (16) , bearing cone spacer (17) , and bearing cone (18) from idler gear
(13) .
Illustration 13 g00871366
18. Use Tooling (C) to remove bearing cup (19) from idler gear (13) .
Illustration 14 g00871367
19. Remove bearing cup spacer (20) from idler gear (13) .
7/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00871368
20. Remove retaining ring (21) from idler gear (13) .
Illustration 16 g00871369
21. Use Tooling (C) to remove bearing cups (22) from idler gear (13) .
8/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00871370
22. Remove studs (23) from torque converter housing assembly (2) .
Illustration 18 g00871267
23. Remove retaining ring (24) and bearing carrier (25) from the carrier assembly.
Illustration 19 g01112906
24. Remove bearing carrier (25) .
9/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00871269
25. Remove O-ring seal (26) from bearing carrier (25) .
26. Remove seal ring (27) from ring carrier (28) .
Illustration 21 g00871273
27. Use Tooling (D) and a press to remove ring carrier (28) from bearing carrier (25) .
10/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00871274
28. Remove retaining ring (29) from bearing carrier (25) .
Illustration 23 g00871275
29. Use Tooling (D) and a press to remove inner bearing (30) from bearing carrier (25) .
Illustration 24 g01112907
30. Remove bolts (31) and the washers from drive gear (32) .
31. Remove drive gear (32) .
11/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 25 g01112910
32. Use Tooling (E) and a press to remove the outer bearing race (32A) (not shown) from drive
gear (32) .
Illustration 26 g00871278
33. Remove retaining ring (33) from drive gear (32) .
Illustration 27 g00871279
12/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 34. Remove bolts (34) and the washers from drive flange (35) and rotating housing (36) .
Illustration 28 g00871281
35. Use bolts (34) as forcing screws to remove drive flange (35) from rotating housing (36) .
The weight of drive flange (35) is 23 kg (51 lb).
Illustration 29 g00871282
36. Remove bolts (37) from drive flange (35) .
13/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 30 g00871283
37. Remove drive flange (35) from impeller (38) .
Illustration 31 g00871284
38. Position impeller hub (39) on wood blocks.
39. Remove impeller (38) from impeller hub (39) .
Illustration 32 g00870210
14/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 40. Remove thrust bearing (40) and race (40A) (not shown) from carrier assembly (41) .
Illustration 33 g00870211
41. Remove carrier assembly (41) and stator (42) as a unit from rotating housing (36) .
Illustration 34 g00870212
42. Remove snap ring (43) from stator (42) . Remove plate (44) from stator (42) .
15/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 35 g01112913
43. Remove 11 freewheel rollers (45) and 11 freewheel springs (46) from freewheel cam (47) .
Remove stator (42) from carrier assembly (41) .
Illustration 36 g01112915
44. Remove retaining ring (48) . Remove plate (49) .
45. Use Tooling (E) and a hydraulic press in order to remove freewheel cam (47) from stator
(42) .
Note: If necessary, heat the stator to a maximum temperature of 135 °C (275 °F) for
approximately 15 minutes.
Illustration 37 g01112917
46. Remove thrust bearing (50) from carrier assembly (41) . Remove sleeve bearing (51) from
carrier assembly (41) .
16/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 38 g01112919
47. Remove thrust bearing race (52) and the thrust bearing.
Illustration 39 g00870286
48. Remove turbine (53) and turbine hub (54) as a unit from rotating housing (36) .
Illustration 40 g01112920
49. Remove bolts (55) and the washers that hold turbine (53) to hub (54) .
17/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 41 g00870755
50. Remove hub (54) from turbine (53) .
Illustration 42 g00870288
51. Remove retaining ring (56) from turbine hub (54) .
18/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 43 g01112924
52. Remove two races (57) and thrust bearing (58) .
Illustration 44 g00870291
53. Remove bolts (59) and the washers from cover assembly (60) .
54. Remove cover assembly (60) from rotating housing (36) .
55. Remove ring seal (61) from rotating housing (36) .
Illustration 45 g00870294
56. Remove sleeve bearing (62) from cover assembly (60) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 22 10:17:08 UTC+0800 2021
19/19
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER MHG
Configuration: 980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine
Disassembly and Assembly
980H Wheel Loader Power Train
Media Number -RENR8667-08 Publication Date -01/09/2018 Date Updated -04/09/2018
i05903427
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
G
8T-5096 Dial Indicator Test Group 1
5P-2390 Gauge Tool Group 1
H 1P-0520 Driver Group 1
J -
Guide Pin
(3/8 - 16 by 8 in)
2
K -
Guide Pin
(1/2 - 13 by 3 in)
3
L 2P-8312 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, thoroughly cleaned in cleaning fluid.
Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement.
Note: Apply oil to all of the bearings before assembly.
1/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01112937
1. Use Tooling (H) to install sleeve bearing (62) in cover assembly (60) . Sleeve bearing (62)
must be even with the outside surface of cover assembly (60) .
Illustration 2 g03337064
2. Install ring seal (61) to rotating housing (36) .
3. Install cover assembly (60) to rotating housing (36) .
4. Install bolts (59) and the washers to cover assembly (60) . Tighten the bolts to a torque of 30
± 5 N·m (22 ± 4 lb ft).
2/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g00870744
5. Install races (57) and thrust bearing (58) to cover assembly (60) .
Illustration 4 g00870748
6. Install retaining ring (56) in turbine hub (54) .
Illustration 5 g00870755
7. Install turbine (53) on hub (54) .
3/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 6 g00870757
8. Install bolts (55) and the washers to turbine (53) . Tighten the bolts to a torque of 50 ± 7
N·m (37 ± 5 lb ft).
Illustration 7 g00870759
9. Install hub (54) and turbine (53) as a unit to rotating housing (36) .
4/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 8 g00870760
10. Install thrust bearing race (52) and the bearing to the turbine hub (54) .
Illustration 9 g01112941
11. Use Tooling (H) and a hydraulic press in order to install sleeve bearing (51) to carrier
assembly (41) . Install thrust bearing (50) to carrier assembly (41) .
Illustration 10 g01112915
5/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 11 g01112913
12. Use Tooling (H) and a hydraulic press in order to install freewheel cam (47) to stator (42) .
13. Install plate (49) to stator (42) . Install retaining ring (48) to stator (42) .
Note: If necessary, heat stator (42) to a maximum temperature of 135 °C (275 °F). Install
the cam with the IMPELLER SIDE facing downward. Continue with the installation until
freewheel cam (47) contacts the retaining ring (not shown).
14. Install stator (42) to carrier assembly (41) . Install freewheel springs (46) and freewheel
rollers (45) to freewheel cam (47) . Always install new freewheel springs (46) and
freewheel rollers (45) . Install freewheel springs (46) with the maximum number of loops in
freewheel springs (46) to the outside of freewheel cam (47) . Use the orientation of stator
(42) in Illustration 11 in reference to the following statement: Stator (42) should turn freely
in the clockwise direction. Stator (42) should not turn freely in the counterclockwise
direction.
Illustration 12 g00870421
15. Install plate (44) to stator (42) . Install snap ring (43) to stator (42) .
6/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 13 g00870422
16. Install carrier assembly (41) and stator (42) as a unit to rotating housing (36) .
Illustration 14 g00870762
17. Install thrust bearing (40) and race (40A) (not shown) to the carrier assembly (41) .
Illustration 15 g00870994
18. Position impeller hub (39) on a wood block.
7/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 19. Install impeller (38) on impeller hub (39) .
Illustration 16 g00870995
20. Install drive flange (35) on impeller (38) .
Illustration 17 g00871000
21. Install bolts (37) on drive flange (35) . Tighten the bolts to a torque of 80 ± 10 N·m (60 ± 7
lb ft).
8/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 18 g00871001
22. Install drive flange (35) on rotating housing (36) . The weight of drive flange (35) is
approximately 23 kg (51 lb).
23. Install bolts (34) and the washers to drive flange (35) . Tighten the bolts to a torque of 30 ±
5 N·m (22 ± 4 lb ft).
Illustration 19 g00871003
24. Install retaining ring (33) in the groove of drive gear (32) .
9/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(SEB...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 20 g00870829
25. Use the proper equipment to handle outer bearing race (32A) . Lower the temperature of
outer bearing race (32A) .
26. Install outer bearing race (32A) in drive gear (32) . Make sure that outer bearing race (32A)
contact retaining ring (33) .
Illustration 21 g00870763
27. Install drive gear (32) on drive flange (35) .
28. Install bolts (31) and the washers on drive gear (32) . Tighten the bolts to a torque of 50 ± 7
N·m (37 ± 5 lb ft).
Illustration 22 g00871006
29. Use the proper equipment to handle inner bearing (30) . Heat inner bearing (30) to a
maximum temperature of 135 °C (275 °F). Install inner bearing (30) on bearing carrier
(25) .
10/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 23 g00871007
30. Install retaining ring (29) in the groove of bearing carrier (25) .
Illustration 24 g00871009
31. Use the proper equipment to handle ring carrier (28) . Heat ring carrier (28) to a maximum
temperature of 135 °C (275 °F). Install ring carrier (28) on bearing carrier (25) .
Illustration 25 g00871012
11/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
33. 32. Install seal ring (27) on ring carrier (28) .
33. Install O-ring seal (26) on bearing carrier (25) .
Illustration 26 g00871014
34. Install bearing carrier (25) in drive flange (35) .
Illustration 27 g00871015
35. Install retaining ring (24) and bearing carrier (25) on carrier assembly (28) .
12/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. Illustration 28 g00872709
36. Install studs (23) in torque converter housing assembly (2) . Tighten the studs to a torque of
100 ± 15 N·m (74 ± 11 lb ft).
Illustration 29 g00872711
37. Install retaining ring (21) in the groove of idler gear (13) .
Illustration 30 g00872713
13/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
35. 38. Use the proper equipment to handle bearing cup (22) . Lower the temperature of bearing cup
(22) . Install bearing cup (22) in idler gear (13) .
Illustration 31 g00872715
39. Flip idler gear (13) to the opposite side. Install bearing cup spacer (20) in idler gear (13) .
The notch in bearing cup spacer (20) must be aligned with retaining ring (21) .
Illustration 32 g00872716
40. Use the proper equipment to handle bearing cup (19) . Lower the temperature of bearing cup
(19) . Install bearing cup (19) in idler gear (13) .
14/20
980H Wheel Loader MHG00001-UP (MACHINE) POWERED BY C-15 Engine(S...
2021/3/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...