This document provides instructions for disassembling and assembling components of a wheel loader's power train, including its torque converter and transmission. It describes removing the transmission from the output transfer gears by disconnecting harnesses, drain tubes, bolts, and separating the components using lifting tools. Steps are outlined for disassembling the transmission planetary, including cleaning parts, applying identification marks, and using pulling tools to remove bearings.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing components like carriers, sun gears, and planet gears in a certain sequence after separating the transmission. Cleanliness is emphasized during disassembly and assembly.
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 30 steps to assemble the torque converter and 17 steps to disassemble the transmission planetary system. Diagrams illustrate the components and tools required, which include link brackets, drivers, retaining ring pliers, and bearing pullers. Safety precautions are provided to prevent injury from released spring forces.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing covers, gears, and shafts after separating it from other components and using various tools. The document emphasizes cleanliness during assembly and disassembly.
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 30 steps to assemble a torque converter, involving installing various bearings, seals, gears and housing components in the proper order. It also describes separating the transmission from the output transfer gears using lifting equipment and specialized tools. Finally, it outlines 24 steps to disassemble the transmission planetary components, beginning with removing housing components and seals, and noting safety precautions for released spring forces.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing covers, gears, and shafts after separating it from other components and using various tools. Cleanliness is emphasized during assembly and disassembly.
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 30 steps to assemble the torque converter and 17 steps to disassemble the transmission planetary system. Diagrams illustrate the components and tools required include link brackets, drivers, retaining ring pliers, and a bearing puller. Cleanliness is emphasized throughout the procedures.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Caterpillar Cat CS-423E Vibratory Compactor (Prefix CFX) Service Repair Manua...fjkskkedmm4r
This document provides assembly instructions for the axle on a CS-423E vibratory compactor. It details 33 steps to assemble components such as the differential, wheel hubs, brakes, and gearbox. Tools and torque specifications are listed. Parts are cleaned and seals/bearings replaced if damaged before assembly. Components like the differential, wheel hubs, brakes, and gearbox are assembled separately then installed on the axle housing.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing components like carriers, sun gears, and planet gears in a certain sequence after separating the transmission. Cleanliness is emphasized during disassembly and assembly.
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 30 steps to assemble the torque converter and 17 steps to disassemble the transmission planetary system. Diagrams illustrate the components and tools required, which include link brackets, drivers, retaining ring pliers, and bearing pullers. Safety precautions are provided to prevent injury from released spring forces.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing covers, gears, and shafts after separating it from other components and using various tools. The document emphasizes cleanliness during assembly and disassembly.
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 30 steps to assemble a torque converter, involving installing various bearings, seals, gears and housing components in the proper order. It also describes separating the transmission from the output transfer gears using lifting equipment and specialized tools. Finally, it outlines 24 steps to disassemble the transmission planetary components, beginning with removing housing components and seals, and noting safety precautions for released spring forces.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing covers, gears, and shafts after separating it from other components and using various tools. Cleanliness is emphasized during assembly and disassembly.
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 30 steps to assemble the torque converter and 17 steps to disassemble the transmission planetary system. Diagrams illustrate the components and tools required include link brackets, drivers, retaining ring pliers, and a bearing puller. Cleanliness is emphasized throughout the procedures.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Caterpillar Cat CS-423E Vibratory Compactor (Prefix CFX) Service Repair Manua...fjkskkedmm4r
This document provides assembly instructions for the axle on a CS-423E vibratory compactor. It details 33 steps to assemble components such as the differential, wheel hubs, brakes, and gearbox. Tools and torque specifications are listed. Parts are cleaned and seals/bearings replaced if damaged before assembly. Components like the differential, wheel hubs, brakes, and gearbox are assembled separately then installed on the axle housing.
Caterpillar Cat CS-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Volvo EC55-2 Compact Excavator Parts Catalogue Manual – SN 5001 - 7620.pdffjkskkedmm4r
This document contains specifications for various engine parts for a Volvo EC55-2 engine. It includes sections for the engine, cylinder head, valves, pistons, connecting rods, camshaft, and other components. Each section lists the relevant part numbers, descriptions, quantities, and other details. The document provides an extensive catalogue of replacement parts for this engine model.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...fjkskkedmm4r
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Pictures and diagrams show the layout and connections between various hydraulic system parts.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
1. The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the spacer plate, valves, valve seat inserts, bridge dowels, valve guides, oil pan and plate, oil pump, and piston cooling tubes.
2. The instructions describe cleaning and preparing surfaces, using specific tools to remove and install components, and ensuring proper installation and operation after reassembly.
3. The overall process involves removing engine components, cleaning surfaces, installing new parts as needed, and reassembling the engine, with the goal of properly servicing the 3406C diesel engine.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
1. Remove the transmission, torque converter, and transfer gears from the tractor. Lift the assembly weighing approximately 1320 kg onto stands.
2. Attach lifting brackets and remove the bolts and nuts securing the 340 kg transfer gears to the transmission. Separate the transfer gears and remove o-rings.
3. Remove the final o-ring seal from the transmission. Install the transfer gears by reversing the removal steps.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and refastening housings and covers.
This document provides step-by-step instructions to disassemble a piston pump. It begins by removing the piston pump and cleaning it. Key components like the piston assemblies, barrel assembly, springs and seals are then removed. Precision tools are required to remove parts like bearings and seals without damage. The multi-stage process dismantles both sides of the pump housing and internal components like valves, solenoids and control blocks are broken down. Precise part tracking and cleanliness are emphasized for reassembly.
This document provides instructions for disassembling and assembling bevel and transfer gears on a D6M track-type tractor. It outlines 22 steps for disassembly, which include removing brackets, yokes, carriers, cages, seals, bearings, gears, pins, shafts, and other components. It then outlines 21 steps for assembly, which involve cleaning parts, installing bearings, gears, pins, shafts, seals, covers, and other components in the reverse order of disassembly. Proper tools and cleaning procedures are emphasized to prevent damage to components from dirt and contaminants.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D6N track-type tractor. It describes removing the final drive, steering clutch, and brake as separate components. It then details each step to disassemble the steering clutch and brake parts and housing. The corresponding assembly instructions are also provided in reverse order.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head. The procedures include removing and installing the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, valve guides, and oil pan and plate. The instructions describe the specific steps to disassemble and reassemble each component.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides instructions for disassembling and assembling components of the retarder and bearing cage (drive shaft) of a 623G wheel tractor. The disassembly procedure involves using various tools to remove 15 different components. The assembly procedure instructs installing the components in reverse order and refers to other documents for installing related components. Safety notices are provided regarding containing fluids and preventing contamination.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...fjkskkedmm4r
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
Caterpillar Cat CS-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Volvo EC55-2 Compact Excavator Parts Catalogue Manual – SN 5001 - 7620.pdffjkskkedmm4r
This document contains specifications for various engine parts for a Volvo EC55-2 engine. It includes sections for the engine, cylinder head, valves, pistons, connecting rods, camshaft, and other components. Each section lists the relevant part numbers, descriptions, quantities, and other details. The document provides an extensive catalogue of replacement parts for this engine model.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...fjkskkedmm4r
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Pictures and diagrams show the layout and connections between various hydraulic system parts.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
1. The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the spacer plate, valves, valve seat inserts, bridge dowels, valve guides, oil pan and plate, oil pump, and piston cooling tubes.
2. The instructions describe cleaning and preparing surfaces, using specific tools to remove and install components, and ensuring proper installation and operation after reassembly.
3. The overall process involves removing engine components, cleaning surfaces, installing new parts as needed, and reassembling the engine, with the goal of properly servicing the 3406C diesel engine.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
1. Remove the transmission, torque converter, and transfer gears from the tractor. Lift the assembly weighing approximately 1320 kg onto stands.
2. Attach lifting brackets and remove the bolts and nuts securing the 340 kg transfer gears to the transmission. Separate the transfer gears and remove o-rings.
3. Remove the final o-ring seal from the transmission. Install the transfer gears by reversing the removal steps.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and refastening housings and covers.
This document provides step-by-step instructions to disassemble a piston pump. It begins by removing the piston pump and cleaning it. Key components like the piston assemblies, barrel assembly, springs and seals are then removed. Precision tools are required to remove parts like bearings and seals without damage. The multi-stage process dismantles both sides of the pump housing and internal components like valves, solenoids and control blocks are broken down. Precise part tracking and cleanliness are emphasized for reassembly.
This document provides instructions for disassembling and assembling bevel and transfer gears on a D6M track-type tractor. It outlines 22 steps for disassembly, which include removing brackets, yokes, carriers, cages, seals, bearings, gears, pins, shafts, and other components. It then outlines 21 steps for assembly, which involve cleaning parts, installing bearings, gears, pins, shafts, seals, covers, and other components in the reverse order of disassembly. Proper tools and cleaning procedures are emphasized to prevent damage to components from dirt and contaminants.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D6N track-type tractor. It describes removing the final drive, steering clutch, and brake as separate components. It then details each step to disassemble the steering clutch and brake parts and housing. The corresponding assembly instructions are also provided in reverse order.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head. The procedures include removing and installing the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, valve guides, and oil pan and plate. The instructions describe the specific steps to disassemble and reassemble each component.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides instructions for disassembling and assembling components of the retarder and bearing cage (drive shaft) of a 623G wheel tractor. The disassembly procedure involves using various tools to remove 15 different components. The assembly procedure instructs installing the components in reverse order and refers to other documents for installing related components. Safety notices are provided regarding containing fluids and preventing contamination.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...fjkskkedmm4r
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Caterpillar Cat 972G Wheel Loader (Prefix 4WW) Service Repair Manual (4WW00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G WHEEL LOADER 4WW
Configuration: 972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
966G and 972G Wheel Loaders Power Train
Media Number -RENR2106-08 Publication Date -01/05/2004 Date Updated -28/05/2004
i07399197
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 2P-8312 Retaining Ring Pliers 1
D 7F-6068 Sleeve 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Illustration 1 g00878809
1. Install bearing (39) and ring (40) on rotating housing (15).
Illustration 2 g00878808
1. Install locating dowel (38) in turbine hub assembly (37).
2. Install turbine hub assembly (37) to turbine (35). Install bolts (36) and the washers. The
torque for bolts (36) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00878784
3. Turn rotating housing (15) onto opposite side. Install turbine (35).
2/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 4 g00878783
4. Install bearing spacer (34).
5. Use Tooling (C) to install retaining ring (33) on turbine hub assembly (37). Retaining ring
(33) must be securely seated in the groove.
6. Install O-ring seal (32).
Illustration 5 g00878781
7. Install end cover (31) and retaining ring (30) in rotating housing (15).
Illustration 6 g00878780
3/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 8. Lower the temperature of bearing (29).
9. Install bearing (29) in impeller (14).
Note: The notch in bearing (29) must face downward, as shown.
Illustration 7 g00878778
10. Install drive gear (28) and bolts (27). The torque for bolts (27) is 105 ± 15 N·m
(75 ± 11 lb ft).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 11
through 16.
Illustration 8 g01151541
11. Install the seal ring (not shown) onto carrier shaft (17). Use a suitable press to install carrier
shaft (17) in impeller (14).
12. Install spacer (26) over shaft (17).
4/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 9 g00878585
13. Install freewheel cam (25), freewheel springs (24), freewheel rollers (23), and bearing race
(22) in stator (19).
Note: If necessary, raise the temperature of stator (19) to a maximum temperature of 135 °C
(275 °F). Install the cam with the IMPELLER SIDE facing downward. Continue with the
installation until freewheel cam (25) contacts the retaining ring (not shown).
Note: Install freewheel springs (24) with the maximum number of loops toward the outside
diameter of freewheel cam (25).
Illustration 10 g00878584
14. Install washer (21) and retaining ring (20) on stator (19). Repeat the procedure for the
opposite side of stator (19).
5/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g00878581
15. Install stator (19) on impeller (14).
16. Install plate (18) and retaining ring (16) on carrier shaft (17).
Illustration 12 g01152618
17. Assemble carrier shaft (17), as follows.
18. Install ring (42) on shaft (41).
19. Use a suitable press to install inner race (43) onto shaft (41).
20. Install outer bearing (44).
6/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 21. Use Tooling (B), Tooling (D), and a suitable press to install shaft assembly (41) and outer
bearing (44) into carrier shaft (17).
22. Install plate (45) and retaining ring (46).
Illustration 13 g00456243
23. Install impeller (14) on rotating housing (15). The weight of the impeller assembly is
approximately 36 kg (80 lb).
24. Install bolts (13) and the washers. The torque for bolts (13) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 14 g00456176
25. Use Tooling (B) to install bearing (12) in pump drive gear (11).
7/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00456168
Illustration 16 g00456172
26. Install pump drive gear (11) and drive gear shaft (10).
27. Use Tooling (A) and a suitable lifting device to install the torque converter housing over the
torque converter. The weight of the torque converter housing is approximately 113 kg
(250 lb).
28. Install bolt (9) and the washer that holds drive gear shaft (10) to the torque converter
housing. The torque for bolt (9) is 240 ± 40 N·m (180 ± 30 lb ft).
Illustration 17 g00456148
29. Install pump drive flange (8) and bolts (7). The torque for bolts (7) is 60 ± 12 N·m
(44 ± 9 lb ft).
8/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g00563276
30. Install bolts (6) and the washers that hold the torque converter to the torque converter
housing. The torque for bolts (6) is 50 ± 10 N·m (37 ± 7 lb ft).
31. Install O-ring seal (5).
Illustration 19 g00563249
32. Install gear (3), retainer (2), and bolt (1). The torque for bolt (1) is 120 ± 20 N·m
(90 ± 15 lb ft).
33. Install torque converter speed sensor (4), the seal, and the washer. Adjust torque converter
speed sensor (4) to maintain an air gap of 0.71 ± 0.18 mm (0.028 ± 0.007 inch). The torque
for torque converter speed sensor (4) is 25 ± 5 N·m (18 ± 4 lb ft).
End By:
a. Connect the torque converter to the transmission and to the output transfer gears. Refer to
Disassembly and Assembly, "Torque Converter to Transmission, Output Transfer Gears -
Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 17 19:27:25 UTC+0800 2021
9/9
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G WHEEL LOADER 4WW
Configuration: 972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
966G and 972G Wheel Loaders Power Train
Media Number -RENR2106-08 Publication Date -01/05/2004 Date Updated -28/05/2004
i02642179
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
Start By:
A. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter from Transmission, Output Transfer Gears - Separate".
Note: Put identification marks on all harness assemblies for installation purposes. Plug all tube
assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the
system.
1/3
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01325525
1. Remove bolts (1) and remove drain tube assembly (2) .
Illustration 2 g01325543
2. Attach Tooling (A) and a suitable lifting device to transmission planetary (4) .
3. Remove O-ring seal (3) .
Illustration 3 g01325555
2/3
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g01325557
4. Disconnect harness assemblies (6). Disconnect harness assembly (8) .
5. Remove bolts (5) which hold transmission planetary (4) to output transfer gear case (7) .
Note: If necessary, use forcing screws in order to separate transmission planetary (4) from
output transfer gear case (7) .
6. Use Tooling (A) and the suitable lifting device in order to separate transmission planetary
(4) from output transfer gear case (7). The weight of transmission planetary (4) is
approximately 545 kg (1200 lb).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 17 19:28:21 UTC+0800 2021
3/3
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G WHEEL LOADER 4WW
Configuration: 972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
966G and 972G Wheel Loaders Power Train
Media Number -RENR2106-08 Publication Date -01/05/2004 Date Updated -28/05/2004
i02299775
Transmission Planetary - Disassemble
SMCS - 3160-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
C 8H-0663 Bearing Puller 1
Start By:
A. Separate the transmission from the output transfer gears. Refer to Disassembly and
Assembly, "Transmission from Output Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00458960
1. Remove O-ring seal (1) from the housing.
2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft.
Illustration 2 g00459007
3. Remove plate (5) .
Illustration 3 g00459030
2/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 4. Attach Tooling (A) and a suitable lifting device to the transmission, as shown. The weight
of the transmission is approximately 544 kg (1200 lb).
5. Carefully position the planetary group on the opposite end so that No. 6 clutch housing (6)
is facing upward, as shown.
Illustration 4 g00459073
6. Remove retaining ring (8) from output shaft (7) .
Illustration 5 g00459075
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 7. Remove bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolts.
Illustration 6 g00459079
8. Remove clutch piston (10) from No. 6 clutch housing (6) .
9. Remove seal rings (11) and (12) from clutch piston (10) .
Illustration 7 g00459087
10. Remove clutch plate (14) and springs (13) .
4/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 11 g00459138
14. Remove metal seal ring (20) from carrier assembly (19) .
Illustration 12 g00459150
15. Use a hammer and a punch to push the spring pins through carrier assembly (19) and into
planetary shafts (21) .
6/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00459151
16. Use a hammer and a punch to remove planetary shafts (21) from carrier assembly (19) .
Illustration 14 g00324725
17. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly.
Remove spring pins (25) from planetary shafts (21) .
Illustration 15 g00459161
18. Remove O-ring seal (26). Remove bolts (27) from manifold (28) .
7/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 16 g00565113
19. Disconnect the harness assemblies which are attached to transmission modulating valves
(29). Remove transmission modulating valves (29) from the transmission housing.
Illustration 17 g00459316
20. Remove retaining ring (32) and gear (30). Remove retaining ring (31) .
Illustration 18 g00459322
8/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 21. Use Tooling (A) and a suitable lifting device to remove manifold (28). The weight of
manifold (28) is approximately 85 kg (190 lb).
22. Remove bolt (33) which holds the harness assembly in place.
Illustration 19 g00459352
23. Remove retaining ring (34) and bearing (35) from manifold (28) .
Illustration 20 g00459369
24. Remove retaining ring (36) and clutch housing (37) .
9/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(SEB...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 21 g00459372
25. Remove O-ring seal (38) from clutch housing (37) .
Illustration 22 g00459375
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Use steel spacers and a suitable press to push on retainer plate (40). Remove retaining ring
(39) from the clutch housing.
10/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 23 g00459387
27. Separate retaining ring (39), retainer plate (40), three coned disc springs (41), and clutch
piston (42) .
Illustration 24 g00459393
28. Remove seal rings (43) from clutch piston (42) .
Illustration 25 g00459394
11/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 29. Remove seal rings (44) from clutch housing (37) .
Illustration 26 g00565119
30. Remove retaining ring (45) from the output shaft. Remove hub (46) .
Illustration 27 g00565685
31. Remove friction discs (47) and clutch plates (48) .
12/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 31 g00459506
35. Remove seal rings (57) and (58) from clutch piston (54) .
Illustration 32 g00565199
36. Use Tooling (A) and a suitable lifting device to remove housing (59). The weight of housing
(59) is approximately 66 kg (145 lb).
Note: The clutch piston may be stuck in housing (59). As housing (59) is removed, the
clutch piston may fall.
14/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 33 g00565203
37. Remove clutch piston (60) .
Illustration 34 g00459540
38. Remove seal rings (61) and (62) from clutch piston (60) .
Illustration 35 g00565255
39. Remove friction discs (63) and clutch plates (64) .
15/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 42. Remove retaining ring (71) and bearing (72) .
Illustration 39 g00459634
43. Use several small steel rods (73) (3.175 mm (0.1250 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (69) to ring gear (74) .
44. Remove carrier assembly (69) from ring gear (74) .
Illustration 40 g00459638
45. Remove retaining ring (75) from carrier assembly (69) .
17/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 41 g00459643
46. Use a hammer and a punch to push the spring pins through carrier assembly (69) and into
planetary shafts (76) .
47. Use a hammer and a punch to remove planetary shafts (76) from carrier assembly (69) .
Illustration 42 g00459646
48. Remove thrust discs (77), planetary gears (78), and bearings (79) from the carrier assembly.
Remove spring pins (80) from planetary shafts (76) .
18/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 43 g00565272
49. Remove retaining ring (81) that holds output shaft (82) to the input shaft. Remove output
shaft (82) .
Illustration 44 g00459776
50. Remove O-ring seal (83) from output shaft (82) .
Illustration 45 g00460029
51. Remove retaining ring (85) .
52. Remove sun gear (84) from output shaft (82) .
19/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 46 g00460030
53. Use a suitable press to push output shaft (82) out of bearing (86), as shown.
Illustration 47 g00460034
54. If necessary, remove bearings (87) from both ends of output shaft (82) .
Illustration 48 g00565282
20/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
34. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
35. 55. Use Tooling (A) and a suitable lifting device to remove housing (88). The weight of housing
(88) is approximately 61 kg (135 lb).
Illustration 49 g00460042
56. Remove clutch piston (89), friction discs (90), and clutch plates (91) .
Illustration 50 g00460045
57. Remove seal rings (92) and (93) from clutch piston (89) .
21/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. Illustration 51 g00460067
58. Remove retaining ring (94) from the input shaft.
59. Remove springs (95) and ring gear (96). Remove O-ring seals (97) and (98) .
Illustration 52 g00460068
60. Remove carrier assembly (99) from the input shaft. The weight of the carrier assembly is
approximately 29 kg (65 lb).
22/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
37. Illustration 53 g00460074
61. Remove gear (100) .
62. Place a suitable wood block under carrier assembly (99) .
63. Use several small steel rods (101) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (99) to ring gear (102) together.
64. Remove ring gear (102) from carrier assembly (99) .
Illustration 54 g00460078
65. Remove retaining ring (105) from carrier assembly (99) .
66. Remove retaining ring (104). Remove sun gear (103) and the bearing. Use Tooling (B) to
remove sun gear (103) and the bearing.
Illustration 55 g00460081
67. Use a hammer and a punch to push the spring pins through carrier assembly (99) and into
planetary shafts (106) .
23/30
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...