This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel linkage, unit injectors, water temperature regulator, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for installing a new cylinder head gasket and cylinder head, ensuring proper torque is applied to the bolts. Reinstalling the other removed components completes the installation.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel control linkage, unit injectors, water temperature regulator housing, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new cylinder head gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fusjefjkskem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
This document provides service information for a lift truck, including specifications, maintenance schedules, part replacements, and adjustments. It contains electrical specifications, speeds, hydraulic details, fluid types, and torque values. Sections cover planned maintenance schedules, adjustments for items like brakes and steering, replacing load wheels and drive tires, and motor service instructions. Troubleshooting guides and instructions are provided for electrical, hydraulic, and transmission systems.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using various tools to properly position, connect and adjust the governor and linkage. Proper torque specifications are provided for bolts. References are made to other documents for additional information.
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...orrf0370383
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. When removing the cylinder head, a lifting device should be used and bolts removed carefully. For installation, the mating surfaces must be cleaned and a new gasket used. Bolts should be lubricated and tightened in a specific sequence and torque. Removing other components like the exhaust manifold is listed as the final step.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...fuusejkddmmd3e
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel control linkage, unit injectors, water temperature regulator housing, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new cylinder head gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fusjefjkskem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
This document provides service information for a lift truck, including specifications, maintenance schedules, part replacements, and adjustments. It contains electrical specifications, speeds, hydraulic details, fluid types, and torque values. Sections cover planned maintenance schedules, adjustments for items like brakes and steering, replacing load wheels and drive tires, and motor service instructions. Troubleshooting guides and instructions are provided for electrical, hydraulic, and transmission systems.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes, clips, pins and bolts to separate the governor and linkage. The installation procedure specifies cleaning and lubricating parts, then reversing the removal steps and using various tools to properly position, connect and adjust the governor and linkage. Proper torque specifications are provided for bolts. References are made to other documents for additional information.
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...orrf0370383
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. When removing the cylinder head, a lifting device should be used and bolts removed carefully. For installation, the mating surfaces must be cleaned and a new gasket used. Bolts should be lubricated and tightened in a specific sequence and torque. Removing other components like the exhaust manifold is listed as the final step.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...fuusejkddmmd3e
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It then details 12 steps to install the cylinder head, such as cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence. The summary also notes the document provides guidance on reusable parts and tools needed.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...dujkdksmdmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. When removing the cylinder head, a lifting device is used and bolts are removed carefully. For installation, the mating surfaces are cleaned and a new gasket is used. The cylinder head bolts are tightened in a specific sequence and torque pattern. Removal of the lifter group is also described which requires first removing the rocker shaft and pushrods.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...jdksmmdmdd
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It then details 12 steps to install the cylinder head, such as cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence. The summary also notes the document provides guidance on determining if parts can be reused.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off the cylinder block and removing the gasket. Reinstallation involves cleaning surfaces, installing a new gasket, lubricating bolts, and tightening bolts in a specific sequence and torque.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...diskkdkdmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing other components first. It then outlines 11 steps to install the cylinder head, including cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...fujkse9didkke3
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolting on the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalling the removed components completes the installation.
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolting on the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalling the removed components completes the installation.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...fjkdksmmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...udfjjjsekkmem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c excavator (prefix kdd) service repair manual (kdd00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix jnk) service repair manual (jnk00001 ...jdfjskekmdme
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c excavator (prefix jcd) service repair manual (jcd00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The disassembly process involves removing 28 components from the travel motor in 28 steps, including removing the head, brake piston, rotating assembly, seals, and other internal parts.
2. Cleanliness is important during disassembly and assembly to prevent contamination. All parts should be cleaned and lubricated before assembly.
3. The assembly process reverses the disassembly steps, involving installing 28 components in 28 steps to reassemble the travel motor. Special tools and torque specifications are provided.
Caterpillar cat 330 c excavator (prefix jab) service repair manual (jab00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix haa) service repair manual (haa00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing seals and installing components in the reverse order of disassembly.
- Tools required include an adapter, nuts, washers, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound.
More Related Content
Similar to Caterpillar cat 325 ln excavator (prefix 3 ll) service repair manual (3ll00001 and up)
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It then details 12 steps to install the cylinder head, such as cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence. The summary also notes the document provides guidance on reusable parts and tools needed.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...dujkdksmdmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. When removing the cylinder head, a lifting device is used and bolts are removed carefully. For installation, the mating surfaces are cleaned and a new gasket is used. The cylinder head bolts are tightened in a specific sequence and torque pattern. Removal of the lifter group is also described which requires first removing the rocker shaft and pushrods.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...jdksmmdmdd
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing bolts and carefully lifting the head off. It then details 12 steps to install the cylinder head, such as cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence. The summary also notes the document provides guidance on determining if parts can be reused.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off the cylinder block and removing the gasket. Reinstallation involves cleaning surfaces, installing a new gasket, lubricating bolts, and tightening bolts in a specific sequence and torque.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
Caterpillar cat 325 l excavator (prefix 3 ll) service repair manual (3ll00001...diskkdkdmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines 7 steps to remove the cylinder head, which include removing other components first. It then outlines 11 steps to install the cylinder head, including cleaning surfaces, installing a new gasket, lubricating and tightening bolts in a specific sequence and torque. The document also provides instructions for removing and installing the lifter group.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...fujkse9didkke3
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolts, and tightening the bolts in a specific sequence. Reinstalling involves reattaching removed components.
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolting on the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalling the removed components completes the installation.
The document provides instructions for removing and installing a cylinder head on a 325 LN excavator powered by a 3116 engine. It describes removing components like the fuel filter base, governor, fuel linkage, and manifolds before removing the cylinder head bolts and gasket. It then describes cleaning surfaces, installing a new gasket, bolting on the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalling the removed components completes the installation.
Caterpillar Cat 325 L EXCAVATOR (Prefix 3LL) Service Repair Manual (3LL00001 ...fjkdksmmdm
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
The document provides instructions for removing and installing a cylinder head on an excavator model 325 LN powered by a 3116 engine. It outlines a multi-step process including removing other engine components first like the fuel filter base and governor. It describes lifting the cylinder head off with a device, removing bolts and gasket, and installing a new gasket. It details cleaning and lubricating surfaces, torquing bolts in a specific sequence, and reinstalling other components after installing the cylinder head.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...udfjjjsekkmem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
Similar to Caterpillar cat 325 ln excavator (prefix 3 ll) service repair manual (3ll00001 and up) (13)
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
Caterpillar cat 330 c excavator (prefix mkm) service repair manual (mkm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly procedure has 28 steps that remove components like the head, springs, plates, and seals. The assembly procedure reverses these steps and provides notes on cleaning, marking parts, and applying thread lock compounds. It cautions that cleanliness is important and springs can cause injury if not assembled properly.
Caterpillar cat 330 c excavator (prefix mca) service repair manual (mca00001 ...jdfjskekmdme
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c excavator (prefix kdd) service repair manual (kdd00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix jnk) service repair manual (jnk00001 ...jdfjskekmdme
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c excavator (prefix jcd) service repair manual (jcd00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The disassembly process involves removing 28 components from the travel motor in 28 steps, including removing the head, brake piston, rotating assembly, seals, and other internal parts.
2. Cleanliness is important during disassembly and assembly to prevent contamination. All parts should be cleaned and lubricated before assembly.
3. The assembly process reverses the disassembly steps, involving installing 28 components in 28 steps to reassemble the travel motor. Special tools and torque specifications are provided.
Caterpillar cat 330 c excavator (prefix jab) service repair manual (jab00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c excavator (prefix haa) service repair manual (haa00001 ...jdfjskekmdme
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing seals and installing components in the reverse order of disassembly.
- Tools required include an adapter, nuts, washers, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound.
Caterpillar cat 330 c excavator (prefix gkx) service repair manual (gkx00001 ...jdfjskekmdme
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) Similarly, it outlines 28 steps for assembly, instructing technicians to replace all seals and gaskets and apply lubricant before reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout the process.
Caterpillar cat 330 c excavator (prefix gag) service repair manual (gag00001 ...jdfjskekmdme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor. It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
2) The assembly section lists 29 steps to reassemble the travel motor by replacing components in the reverse order of disassembly. Special tools are required for tasks like removing races and installing seals and rings.
3) Cleanliness is important during disassembly and assembly. Marks should be made to ensure parts are replaced in the same positions. Seal surfaces require compound and components need light oil applied before assembly.
Caterpillar cat 330 c excavator (prefix btm) service repair manual (btm00001 ...jdfjskekmdme
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It details 28 steps for disassembly, removing components like the head, port plate, springs, brake piston, plates, and bearings. It then details 21 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Tools required are also listed.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator including:
1. The cylinder head removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts in a specific tightening sequence.
3. Removing the spacer plate requires taking out seals and removing the plate from the cylinder head. Installing requires new seals and gaskets and ensuring surfaces are clean.
Caterpillar cat 330 b l excavator (prefix 8sr) service repair manual (8sr0000...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b l excavator (prefix 5ls) service repair manual (5ls0000...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, tightening bolts in sequences, and verifying end play. The crankshaft removal requires aligning timing marks, removing caps and nuts, pushing pistons down, lifting the crankshaft out using brackets, and removing gears and seals.
Caterpillar cat 330 b l excavator (prefix 4rs) service repair manual (4rs0000...jdfjskekmdme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe procedures for removing and installing the cylinder head, rocker shaft and pushrods. Specifically, they outline removing the cylinder head by first removing associated components like the fuel lines, exhaust manifold, and rocker shaft. They then describe loosening bolts and using lifting devices to remove the heavy cylinder head. Procedures are also provided for disassembling, cleaning, inspecting, and reassembling the rocker shaft.
Caterpillar cat 330 b excavator (prefix 9hn) service repair manual (9hn00001 ...jdfjskekmdme
This document provides instructions for removing and installing final drives on an excavator. Key steps include:
1. Releasing hydraulic pressure and removing the track assemblies.
2. Removing bolts and disconnecting hydraulic lines to separate the final drive from the undercarriage frame.
3. Cleaning components and installing new seals before reassembling in reverse order, taking care to properly tighten bolts and reconnect hydraulic components.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8sr) service repair manual (8sr00001 ...jdfjskekmdme
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat 330 b excavator (prefix 5ls) service repair manual (5ls00001 ...jdfjskekmdme
The document provides instructions for removing and installing connecting rod bearings, crankshaft main bearings, and the crankshaft on a Caterpillar 330B excavator engine. The procedures include using tools to check bearing clearances, installing bearings dry and oiled, torquing fasteners, and aligning identification marks. The crankshaft removal requires lifting it straight up after removing connecting rods, main bearing caps, and thrust plates.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01935828
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
b. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
c. Remove the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection
Control Linkage - Remove".
d. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
e. Remove the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing - Remove and Install".
f. Remove the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold -
Remove".
g. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 1 g01007597
Typical example
1. Attach a suitable lifting device to the cylinder head.
2/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00654709
2. Remove bolts (1) and (2) that hold the cylinder head to the cylinder block. Carefully remove
the cylinder head from the cylinder block. The cylinder head for the 3116 engine weighs
approximately 85 kg (187 lb).
Illustration 3 g00611342
3. Remove cylinder head gasket (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 4 23:17:20 UTC+0800 2020
3/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i04147334
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4876 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the cylinder head, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114,
3116, and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/5
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g00611342
Typical example
2. Install a new cylinder head gasket (3) .
Note: For information on the cylinder head gasket for 3116 engines, refer to Special
Instruction, SEHS9395, "3116 Cylinder Head Gasket Usage".
Illustration 2 g01007597
Typical example
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to
install the cylinder head.
3. Attach a suitable lifting device to the cylinder head. Position the cylinder head assembly
onto the dowels in the cylinder block. Lower the cylinder head onto the cylinder block.
2/5
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 3 g00654709
4. Inspect the condition of cylinder head bolts (1) and (2) . For information on the reusability
of the bolts, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8301,
"Inspection and Reuse of Critical Fasteners Used in All Engines". Replace cylinder head
bolts (1) and (2) , if necessary.
5. Lubricate cylinder head bolts (1) and (2) and both sides of the washers with Tooling (A) .
Install cylinder head bolts (1) and (2) . Follow Step 6 for the correct tightening procedure.
Illustration 4 g00641677
3114 Cylinder head
3/5
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 5 g00611358
6. Tighten the cylinder head bolts according to the following procedure:
7. Tighten bolts (1) through bolt (14) in a numerical sequence to a torque of 300 ± 15 N·m
(221 ± 11 lb ft).
8. Loosen bolts (1) through bolt (14) to a torque of 0 N·m.
9. Tighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
10. Retighten bolts (1) through bolt (14) again in a numerical sequence to a torque of 130 ± 15
N·m (96 ± 11 lb ft).
11. Turn bolts (1) through bolt (14) by numerical sequence an additional 90° (1/4 turn).
12. Tighten bolt (15) through bolt (20) in a numerical sequence to a torque of 55 ± 7 N·m (41 ±
5 lb ft).
End By:
a. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
b. Install the inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
c. Install the water temperature regulator housing. Refer to Disassembly and Assembly,
"Water Temperature Regulator Housing- Remove and Install".
d. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
e. Install the fuel control linkage. Refer to Disassembly and Assembly, "Fuel Injection Control
Linkage - Install".
f. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
g. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
4/5
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930413
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 1 g00747310
1. Remove bolts (1) from cover (2).
2. Carefully remove cover (2) and the gasket.
Note: It may be necessary to remove the governor in order to remove the cover at the front
of the engine.
Illustration 2 g00629677
3. Remove bolts (4), lifter shaft (5), and lifters (3) from cover (2).
Installation Procedure
2/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of components of the lifter group, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8264, "Camshaft Roller Followers Used in 3114
and 3116 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8067,
"Slipper Followers and Camshaft Roller Followers".
Illustration 3 g00629677
1. Position lifters (3) and lifter shaft (5) on cover (2). Install bolts (4).
Illustration 4 g00747310
2. Position the gasket and cover (2) on the engine.
3. Install bolts (1) in cover (2).
End By:
3/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 4 23:19:11 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01930426
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the governor. Refer to Disassembly and Assembly, "Governor - Remove".
b. Remove the side covers. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Note: The air compressor was removed in order to accommodate the engine repair stand.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
Illustration 1 g01007643
Typical example
2. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 2 g01007645
3. Remove bolts (4) and camshaft retainer plate (6).
4. Remove camshaft gear (5) and camshaft (3) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 4 23:20:07 UTC+0800 2020
3/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01936378
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the camshaft, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8097, "Camshaft Measurement", Guideline For Reusable Parts And
Salvage Operations, SEBF8146, "Visual Inspection of Camshafts", and Guideline For Reusable
Parts And Salvage Operations, SEBF8251, "Specifications for Measurement of Camshafts in
3114/3116 Engines". For information on reusability of the camshaft gear, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Lubricate the camshaft and the camshaft bearings with clean engine oil.
1/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g01007645
2. Carefully install camshaft (3) and camshaft gear (5) in the engine.
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
Illustration 2 g01007643
Typical example
3. Ensure that timing mark (1) on the camshaft gear is aligned with timing mark (2) on the
idler gear.
2/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 4. Install camshaft retainer plate (6) and bolts (4).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the side cover. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
c. Install the governor. Refer to Disassembly and Assembly, "Governor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 4 23:21:03 UTC+0800 2020
3/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01171077
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00611152
NOTICE
1/2
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Place the camshaft and camshaft gear (1) in a suitable press. Press the camshaft from
camshaft gear (1).
Installation Procedure
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
Illustration 2 g00611152
1. Heat the camshaft gear to a maximum temperature of 315 °C (600 °F).
2. Align the key in the camshaft with the groove (keyway) in the camshaft gear.
3. Install the camshaft gear on the end of the camshaft.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 4 23:21:59 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02183087
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
1. Use Tooling (A) to remove the camshaft bearings from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g01104577
3/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 2 g01104579
1. Use Tooling (A) to install all of the camshaft bearings except for the front bearing. Orient
oil hole (1) in each bearing so that oil hole (1) is located at the top of the bore.
2. Use Tooling (A) to install the front camshaft bearing. Align oil hole (1) in the front
camshaft bearing with the oil hole in the cylinder block. Locate joint (2) in the front
camshaft bearing in the proper position.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 4 23:22:54 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 LN EXCAVATOR 3LL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01572486
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
325, 325 L AND 325 LN EXCAVATORS 3LL00001-UP (MACHINE) POWERED B...
2020/8/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...