This document provides assembly instructions for a Flexxaire fan on a 938G wheel loader. It describes how to assemble the shifter block, hub, actuator bearings/control shaft, install an O-ring on the main shaft, and install main bearing cups. The instructions include illustrations and notes about lubrication, torque specifications, and verifying clearances at various steps.
Caterpillar cat 938 g wheel loader (prefix 6ws) service repair manual (6ws000...fisjejfskemmd
This document provides assembly instructions for a Flexxaire fan on a 938G wheel loader. It describes how to assemble the shifter block, hub, actuator bearings/control shaft, install an O-ring on the main shaft, and install main bearing cups. The instructions include illustrations and notes about lubrication, torque specifications, and verifying clearances at various steps.
Caterpillar cat 994 d wheel loader (prefix 3tz) service repair manual (3tz000...ufjkskemfseol
This document provides instructions for removing the engine oil pump from a Caterpillar 994D wheel loader. It describes draining the coolant, disconnecting electrical connections, and removing mounting bolts and brackets. Special tools are required to lift the oil pump, which weighs approximately 45 kg, away from the drive mechanism.
Caterpillar cat 962 g wheel loader (prefix 3bs) service repair manual (3bs000...dikdkskmmdm
This document provides instructions for disassembling and assembling the axle housing of a 962G wheel loader. It describes 18 steps to disassemble the axle housing, including removing retaining rings, planetary gears, bearings, seals, and other components. It also outlines proper procedures for installing new Duo-Cone seals to prevent seal failures, such as cleaning all components, positioning the rubber rings and seals correctly, and ensuring proper dimensions during installation. The document includes illustrations to supplement the written instructions.
Caterpillar cat 966 k wheel loader (prefix pbg) service repair manual (pbg000...fjjskkemsmee
This document provides instructions for assembling and disassembling a limited slip differential for a 966K wheel loader. It includes 15 steps for assembly, requiring various tools, and lubricating and installing each part in the correct order. It also lists 2 steps for disassembly, including marking the differential case halves and using a press to remove bolts and release spring compression safely.
Caterpillar cat 966 f wheel loader (prefix 8bg) service repair manual (8bg000...fjjskkemsmee
This document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the torque converter by removing components like housing bolts, gears, bearings, seals and shafts. It then describes 26 steps for reassembling the torque converter by reversing the disassembly steps and ensuring proper alignment of components. Tools required include link brackets, drivers and pliers.
Caterpillar cat 966 f wheel loader (prefix 3xj) service repair manual (3xj000...fjjskkemsmee
The document provides instructions for disassembling and assembling axle shaft assemblies and brake groups for a Caterpillar 966F wheel loader. It describes removing and installing various components of the axle shaft assemblies and brake groups, including planetary carrier assemblies, axle shafts, seals, bearings, springs, and reaction plates. Detailed steps are provided for disassembling, cleaning, heating or cooling components as needed, and reassembling the axle shaft assemblies and brake groups.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsjjekdkme
The document provides instructions for installing a cylinder head on a 120G motor grader with a 3304 engine. It involves 16 steps: cleaning and preparing surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and installing related components like intake pipes and hoses. The instructions emphasize keeping parts clean to prevent wear and include illustrations to clarify steps.
This document provides instructions for removing and installing fuel injection lines and an automatic timing advance on a 3406 engine for a generator set. The steps include removing nuts and bolts to detach the lines and timing advance, cleaning surfaces, installing new gaskets, and tightening to the specified torques. Disassembly and assembly of the automatic timing advance and fuel transfer pump are also described in detail with accompanying diagrams.
Caterpillar cat 938 g wheel loader (prefix 6ws) service repair manual (6ws000...fisjejfskemmd
This document provides assembly instructions for a Flexxaire fan on a 938G wheel loader. It describes how to assemble the shifter block, hub, actuator bearings/control shaft, install an O-ring on the main shaft, and install main bearing cups. The instructions include illustrations and notes about lubrication, torque specifications, and verifying clearances at various steps.
Caterpillar cat 994 d wheel loader (prefix 3tz) service repair manual (3tz000...ufjkskemfseol
This document provides instructions for removing the engine oil pump from a Caterpillar 994D wheel loader. It describes draining the coolant, disconnecting electrical connections, and removing mounting bolts and brackets. Special tools are required to lift the oil pump, which weighs approximately 45 kg, away from the drive mechanism.
Caterpillar cat 962 g wheel loader (prefix 3bs) service repair manual (3bs000...dikdkskmmdm
This document provides instructions for disassembling and assembling the axle housing of a 962G wheel loader. It describes 18 steps to disassemble the axle housing, including removing retaining rings, planetary gears, bearings, seals, and other components. It also outlines proper procedures for installing new Duo-Cone seals to prevent seal failures, such as cleaning all components, positioning the rubber rings and seals correctly, and ensuring proper dimensions during installation. The document includes illustrations to supplement the written instructions.
Caterpillar cat 966 k wheel loader (prefix pbg) service repair manual (pbg000...fjjskkemsmee
This document provides instructions for assembling and disassembling a limited slip differential for a 966K wheel loader. It includes 15 steps for assembly, requiring various tools, and lubricating and installing each part in the correct order. It also lists 2 steps for disassembly, including marking the differential case halves and using a press to remove bolts and release spring compression safely.
Caterpillar cat 966 f wheel loader (prefix 8bg) service repair manual (8bg000...fjjskkemsmee
This document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the torque converter by removing components like housing bolts, gears, bearings, seals and shafts. It then describes 26 steps for reassembling the torque converter by reversing the disassembly steps and ensuring proper alignment of components. Tools required include link brackets, drivers and pliers.
Caterpillar cat 966 f wheel loader (prefix 3xj) service repair manual (3xj000...fjjskkemsmee
The document provides instructions for disassembling and assembling axle shaft assemblies and brake groups for a Caterpillar 966F wheel loader. It describes removing and installing various components of the axle shaft assemblies and brake groups, including planetary carrier assemblies, axle shafts, seals, bearings, springs, and reaction plates. Detailed steps are provided for disassembling, cleaning, heating or cooling components as needed, and reassembling the axle shaft assemblies and brake groups.
Caterpillar cat 120 g motor grader (prefix 87v) service repair manual (87v083...fjsjjekdkme
The document provides instructions for installing a cylinder head on a 120G motor grader with a 3304 engine. It involves 16 steps: cleaning and preparing surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and installing related components like intake pipes and hoses. The instructions emphasize keeping parts clean to prevent wear and include illustrations to clarify steps.
This document provides instructions for removing and installing fuel injection lines and an automatic timing advance on a 3406 engine for a generator set. The steps include removing nuts and bolts to detach the lines and timing advance, cleaning surfaces, installing new gaskets, and tightening to the specified torques. Disassembly and assembly of the automatic timing advance and fuel transfer pump are also described in detail with accompanying diagrams.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 4fb) service ...ufjkskemfseol
1) The document provides instructions for removing and installing the high-low transmission on a D8L track-type tractor.
2) Over 50 steps are outlined for disassembling the transmission down to individual components and reassembling it.
3) Key steps include removing the transmission from the engine using lifting tools, taking apart the clutch groups and planetary components, and cleaning and inspecting all parts before reassembly.
Caterpillar cat 352 f excavator (prefix ndc) service repair manual (ndc00001 ...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 352F excavator. It begins by describing how to safely remove the travel motor and various components using specialized tools. Detailed steps are provided to disassemble the motor head assembly, barrel assembly, piston assemblies, and other internal parts. Specifications and torque values are included for reassembly. The process concludes with lubricating and installing components in reverse order.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjsjjekdkme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. The steps include:
1. Ensuring the number 1 piston is at top center position for timing.
2. Installing alignment tools in the flywheel housing.
3. Checking valve timing and turning the flywheel until the number 1 piston is at the correct position.
4. Installing the fuel injection pump housing and governor according to the assembly procedure.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...fjskekdmjekm
The document provides instructions for removing and installing various engine components of a 219D Excavator, including the cylinder head, spacer plate, and water directors. It describes removing components like bolts, gaskets and seals in a specific order. Installation is the reverse of removal, applying new gaskets and torquing bolts to the specified values. Precautions are given to keep components clean and contain fluids.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 160 h motor grader (prefix 9jm) service repair manual (9jm000...fujsjefjwekskemm
This document provides instructions for assembling and installing a piston pump on a Caterpillar 160H motor grader. It lists the required tools and parts, and provides 29 detailed steps for assembling the pump components in the proper order. These include installing bearings, seals, pistons, springs, plates and bolts. The final section provides 6 steps for installing the assembled pump on the grader frame, including positioning it with a lifting device and securing it with brackets, bolts, nuts and rubber mounts.
Caterpillar cat 962 h wheel loader (prefix m3g) service repair manual (m3g000...udjjjsjekkdm
This document provides instructions for disassembling and assembling the piston pump of a 962H wheel loader. It gives detailed steps for disassembling components like valves, spools, plugs, springs, and bearings. It then describes the assembly process in reverse order, noting things like applying the correct torque to bolts and checking axial shaft end play. The overall document provides a technical service manual for maintenance and repair work on the loader's steering pump.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w000...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 130G motor grader with a 3304 engine. It describes removing components like the fuel injection lines, exhaust manifold, rocker shaft and pushrods. It then details removing the cylinder head bolts and lifting the head off. Reinstallation involves cleaning surfaces, installing gaskets and bolts, and adjusting valves. Precautions are given to keep parts clean and contain fluids.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjkskedmme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, bushings and seals in precise orientations, and applying thread lock compounds when specified. Torque values are provided for fasteners.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...cfvdssd
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling components like the shifter block, hub, actuator bearings, control shaft bushings, frost plug, main shaft O-ring, and main bearing cups. The instructions include illustrations and specify torque specifications for fasteners.
This document provides instructions for assembling and disassembling components of the governor assembly and fuel injection pump on a 3034 engine for Caterpillar built machines. It describes how to assemble the governor control lever and fuel control lever, install the governor weight assembly and speed control lever. It also provides instructions for removing and installing the fuel injection pump, including cleaning surfaces, installing shims and dowels, and connecting linkages and springs.
This document provides instructions for removing the fuel injection pump from a Caterpillar 3034 engine. It describes:
1) Disconnecting fuel lines and removing cover bolts and cover from the engine
2) Disconnecting springs from the governor control pin and linkage
3) Removing bolts and nuts to separate the fuel injection pump from the engine mounting face
4) Recording shim thickness and numbers for reassembly, and inspecting dowels for damage
This document provides instructions for assembling the governor assembly and installing the fuel injection pump on a Caterpillar 3034 engine. It describes assembling the governor control lever and fuel control lever, installing the governor weight assembly and speed control lever. It then details installing the fuel injection pump, ensuring proper shim thickness and attaching linkages and springs. The goal is to assemble the governor components in the engine housing and correctly install the fuel injection pump.
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h036...fujseskemmesd
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, lubrication, and other technical details. The document contains detailed explanations and examples of using service tools, pressing parts, bolt torque, locks, and working with lines, wires, shims, bearings, gaskets, and batteries during the repair process.
New holland l223 tier 4 skid steer loader service repair manual [ndm474381 ]fujseskemmesd
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders with Tier 4 engines. It provides specifications and repair/maintenance instructions for the engine, drivetrain, hydraulic and electrical systems, frames, wheels/tracks, cab climate control, front loader/bucket, and other components. Safety precautions for working on the equipment are also outlined. The manual is intended solely for use by qualified dealership personnel.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...fujseskemmesd
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries provide the key steps for each procedure, including any required tools and cleaning/lubrication requirements. Detailed illustrations are included to identify the specific components.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
The document provides instructions for installing a transmission on a 428D backhoe loader. It describes using various tools to position the transmission and connect components. Fourteen bolts are installed to secure the transmission to the engine. Electrical connectors and fluid lines are then connected. Finally, inspection plates are installed and tools are removed upon completion.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
1) Removing fuel injection lines, loosening nuts, and removing nozzles and seat washers from the cylinder head.
2) Cleaning threads, installing new seat washers, applying anti-seize compound, positioning nozzles, and tightening nuts to specifications.
3) For fuel injection pumps, it describes removing water pumps, lines, bolts, nuts, and O-rings, using timing pins to ensure correct positioning, and special tools that may be required.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
This document provides instructions for disassembling and assembling the final drive and drive/steering axle housing of a 428D backhoe loader. The disassembly process involves removing snap rings, thrust washers, bearings and seals from the final drive hub. The assembly process describes installing these components in reverse order and adjusting end play.
New holland cx5080 elevation combine harvesters service repair manualfujseskemmesd
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
The document provides disassembly instructions for a 428D backhoe loader transmission. It lists 30 steps to fully disassemble the transmission along with required tools. These steps include removing valve groups, shafts, seals, bearings, gears, and other internal components. Detailed illustrations accompany each step to show how to remove the individual parts in the proper order. Cleanliness is emphasized when disassembling to prevent dirt from entering components.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 4fb) service ...ufjkskemfseol
1) The document provides instructions for removing and installing the high-low transmission on a D8L track-type tractor.
2) Over 50 steps are outlined for disassembling the transmission down to individual components and reassembling it.
3) Key steps include removing the transmission from the engine using lifting tools, taking apart the clutch groups and planetary components, and cleaning and inspecting all parts before reassembly.
Caterpillar cat 352 f excavator (prefix ndc) service repair manual (ndc00001 ...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 352F excavator. It begins by describing how to safely remove the travel motor and various components using specialized tools. Detailed steps are provided to disassemble the motor head assembly, barrel assembly, piston assemblies, and other internal parts. Specifications and torque values are included for reassembly. The process concludes with lubricating and installing components in reverse order.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjsjjekdkme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. The steps include:
1. Ensuring the number 1 piston is at top center position for timing.
2. Installing alignment tools in the flywheel housing.
3. Checking valve timing and turning the flywheel until the number 1 piston is at the correct position.
4. Installing the fuel injection pump housing and governor according to the assembly procedure.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...fjskekdmjekm
The document provides instructions for removing and installing various engine components of a 219D Excavator, including the cylinder head, spacer plate, and water directors. It describes removing components like bolts, gaskets and seals in a specific order. Installation is the reverse of removal, applying new gaskets and torquing bolts to the specified values. Precautions are given to keep components clean and contain fluids.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 160 h motor grader (prefix 9jm) service repair manual (9jm000...fujsjefjwekskemm
This document provides instructions for assembling and installing a piston pump on a Caterpillar 160H motor grader. It lists the required tools and parts, and provides 29 detailed steps for assembling the pump components in the proper order. These include installing bearings, seals, pistons, springs, plates and bolts. The final section provides 6 steps for installing the assembled pump on the grader frame, including positioning it with a lifting device and securing it with brackets, bolts, nuts and rubber mounts.
Caterpillar cat 962 h wheel loader (prefix m3g) service repair manual (m3g000...udjjjsjekkdm
This document provides instructions for disassembling and assembling the piston pump of a 962H wheel loader. It gives detailed steps for disassembling components like valves, spools, plugs, springs, and bearings. It then describes the assembly process in reverse order, noting things like applying the correct torque to bolts and checking axial shaft end play. The overall document provides a technical service manual for maintenance and repair work on the loader's steering pump.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w000...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 130G motor grader with a 3304 engine. It describes removing components like the fuel injection lines, exhaust manifold, rocker shaft and pushrods. It then details removing the cylinder head bolts and lifting the head off. Reinstallation involves cleaning surfaces, installing gaskets and bolts, and adjusting valves. Precautions are given to keep parts clean and contain fluids.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjkskedmme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, bushings and seals in precise orientations, and applying thread lock compounds when specified. Torque values are provided for fasteners.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...cfvdssd
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling components like the shifter block, hub, actuator bearings, control shaft bushings, frost plug, main shaft O-ring, and main bearing cups. The instructions include illustrations and specify torque specifications for fasteners.
This document provides instructions for assembling and disassembling components of the governor assembly and fuel injection pump on a 3034 engine for Caterpillar built machines. It describes how to assemble the governor control lever and fuel control lever, install the governor weight assembly and speed control lever. It also provides instructions for removing and installing the fuel injection pump, including cleaning surfaces, installing shims and dowels, and connecting linkages and springs.
This document provides instructions for removing the fuel injection pump from a Caterpillar 3034 engine. It describes:
1) Disconnecting fuel lines and removing cover bolts and cover from the engine
2) Disconnecting springs from the governor control pin and linkage
3) Removing bolts and nuts to separate the fuel injection pump from the engine mounting face
4) Recording shim thickness and numbers for reassembly, and inspecting dowels for damage
This document provides instructions for assembling the governor assembly and installing the fuel injection pump on a Caterpillar 3034 engine. It describes assembling the governor control lever and fuel control lever, installing the governor weight assembly and speed control lever. It then details installing the fuel injection pump, ensuring proper shim thickness and attaching linkages and springs. The goal is to assemble the governor components in the engine housing and correctly install the fuel injection pump.
Similar to Caterpillar cat 938 g wheel loader (prefix 6ws) service repair manual (6ws00001 and up) (6)
Caterpillar cat 951 c track loader (prefix 69h) service repair manual (69h036...fujseskemmesd
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, lubrication, and other technical details. The document contains detailed explanations and examples of using service tools, pressing parts, bolt torque, locks, and working with lines, wires, shims, bearings, gaskets, and batteries during the repair process.
New holland l223 tier 4 skid steer loader service repair manual [ndm474381 ]fujseskemmesd
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders with Tier 4 engines. It provides specifications and repair/maintenance instructions for the engine, drivetrain, hydraulic and electrical systems, frames, wheels/tracks, cab climate control, front loader/bucket, and other components. Safety precautions for working on the equipment are also outlined. The manual is intended solely for use by qualified dealership personnel.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...fujseskemmesd
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group removal and installation
- Camshaft removal and installation
- Camshaft bearing removal and installation
- Engine oil pan removal and installation
The summaries provide the key steps for each procedure, including any required tools and cleaning/lubrication requirements. Detailed illustrations are included to identify the specific components.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
The document provides instructions for installing a transmission on a 428D backhoe loader. It describes using various tools to position the transmission and connect components. Fourteen bolts are installed to secure the transmission to the engine. Electrical connectors and fluid lines are then connected. Finally, inspection plates are installed and tools are removed upon completion.
Caterpillar cat 428 d backhoe loader (prefix bns) service repair manual (bns0...fujseskemmesd
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes:
1) Removing fuel injection lines, loosening nuts, and removing nozzles and seat washers from the cylinder head.
2) Cleaning threads, installing new seat washers, applying anti-seize compound, positioning nozzles, and tightening nuts to specifications.
3) For fuel injection pumps, it describes removing water pumps, lines, bolts, nuts, and O-rings, using timing pins to ensure correct positioning, and special tools that may be required.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
This document provides instructions for disassembling and assembling the final drive and drive/steering axle housing of a 428D backhoe loader. The disassembly process involves removing snap rings, thrust washers, bearings and seals from the final drive hub. The assembly process describes installing these components in reverse order and adjusting end play.
New holland cx5080 elevation combine harvesters service repair manualfujseskemmesd
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Caterpillar cat 428 d backhoe loader (prefix bnb) service repair manual (bnb0...fujseskemmesd
The document provides disassembly instructions for a 428D backhoe loader transmission. It lists 30 steps to fully disassemble the transmission along with required tools. These steps include removing valve groups, shafts, seals, bearings, gears, and other internal components. Detailed illustrations accompany each step to show how to remove the individual parts in the proper order. Cleanliness is emphasized when disassembling to prevent dirt from entering components.
Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt0...fujseskemmesd
This document provides instructions for removing and disassembling a steering metering pump on a 428D Backhoe Loader. It describes 18 steps to disassemble the pump by removing components like bolts, seals, springs, and fittings. Safety precautions are provided to prevent injury from hydraulic pressure and ensure cleanliness when handling components.
Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt0...fujseskemmesd
The document provides instructions for removing and disassembling the transmission of a 428D backhoe loader. It describes using various tools to support the machine, drain the transmission oil, disconnect electrical connections and hydraulic lines, and remove mounting bolts. The transmission can then be lowered from the machine and further disassembled into its major components on a repair stand, including removing valve groups, sensors, seals, and gaskets. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 428 d backhoe loader (prefix bll) service repair manual (bll0...fujseskemmesd
The document provides instructions for disassembling the transmission of a 428D backhoe loader. It describes removing the transmission from the machine and then disassembling it into its major components. These include removing the case, output shafts on both sides, input shaft, and other internal parts. Detailed steps are given for removing each part, often using specialized tools. Cleanliness is stressed and removal of fluid is described.
New holland cx880 combine harvesters service repair manualfujseskemmesd
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland cx6.90 fpt cursor 9 stage iv combine harvester service repair manualfujseskemmesd
This service manual provides maintenance and repair information for several combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual is divided into sections covering different vehicle systems such as the engine, transmission, hydraulic systems, electrical systems, and attachments. Each section contains technical data, descriptions of system operation, diagnostic procedures, and service instructions.
Caterpillar cat 322 c excavator (prefix fed) service repair manual (fed00001 ...fujseskemmesd
The document provides instructions for disassembling a pilot valve used in Caterpillar 322C and 322C L excavators. It outlines 19 steps to remove components like fittings, seals, covers, bushings and pushrods. Cleanliness is emphasized when disassembling to prevent dirt from entering internal mechanisms. Identification marks are to be placed on components for reassembly. Personal protective equipment is recommended when releasing spring forces during disassembly.
New holland cr980 combine harvesters service repair manualfujseskemmesd
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electronics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians to safely and efficiently service and repair the equipment.
Caterpillar cat 322 c excavator (prefix bgr) service repair manual (bgr00001 ...fujseskemmesd
This document provides instructions for disassembling the control valve and auxiliary control valve on a 322C excavator. It describes removing various components like solenoid valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contaminating the hydraulic system. The multi-step process includes removing bolts, plugs, springs and O-rings from components like the valve housing, spool and relief valves.
New holland c238 tier 4 compact track loader service repair manual [ncm425510...fujseskemmesd
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders with Tier 4 engines. It provides specifications and repair/maintenance instructions for the engine, drive systems, brakes, hydraulics, frames, wheels/tracks, climate control, electrical systems, front loader/bucket, cab, and decals. Safety precautions for working on the equipment are also outlined. The manual is intended solely for use by qualified dealership personnel.
Caterpillar cat 320 c ln 320cln excavator (prefix bcn) service repair manual ...fujseskemmesd
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Fuel filter base
- Fuel injection lines
- Fuel injection nozzles
- Fuel shutoff solenoid
- Fuel injection pump
The procedures describe disconnecting fuel lines, removing mounting bolts and other hardware, taking care to plug openings to prevent contamination. Proper tools are listed and installation is the reverse of removal. Safety notices warn to contain fluids and keep parts clean.
Caterpillar cat 320 c l excavator (prefix amc) service repair manual (amc0000...fujseskemmesd
This document provides instructions for removing and installing various components of the heating, ventilation, and air conditioning (HVAC) system on a 320C excavator, including:
1) Actuator motors for different air dampers and controls.
2) The fan speed control component.
3) The ambient air temperature sensor.
Detailed step-by-step procedures are provided with accompanying illustrations for each removal and installation process. Safety precautions and proper alignment of linkages are emphasized.
Case ih stx425 steiger tractor service repair manual pin jee0102001 and afterfujseskemmesd
The document provides instructions for removing and installing the engine on STX Steiger tractors. It is a 12-step process for removal that includes draining fluids, disconnecting wiring and hoses, and using an overhead hoist to lift the engine out of the tractor. The 13-step installation process reverses these steps, lowering the engine back into place and reconnecting all components. Safety warnings are provided throughout regarding working around heavy components, hot or pressurized fluids, and ensuring the engine is properly supported during removal and installation.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 938G WHEEL LOADER 6WS
Configuration: 938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
Flexxaire Fan
Media Number -RENR3699-07 Publication Date -01/02/2012 Date Updated -21/06/2016
i01742847
Mechanical Actuated Fan - Assemble
SMCS - 1356-016
Shifter Block − Assemble
Note: The following procedure should only be performed by persons that have taken the fan
rebuilding training course at FLEXXAIRE Manufacturing Inc. The shifter block assembly is sold
only as an assembly unless you have had the training.
Note: Proceed to “Hub - Assemble” if you have purchased a shifter block assembly.
Illustration 1 g00597621
1. Thread elbow (3) onto pickup tube (2). Then, thread pickup tube (2) into through shaft
bearing end (1).
Note: The orientation of pickup tube (2) in Illustration 2 is shown in the most common
direction. However, other applications may require pickup tube (2) to be rotated 180
degrees. Pickup tube (2) is stationary. Pickup tube (2) does not rotate. The arrows indicate
the direction of oil flow into pickup tube (2).
1/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00597622
2. Slide bearing cone (4) onto through shaft bearing end (1). Slide wave washer (5) and spacer
(6) onto through shaft bearing end (1).
Illustration 3 g00597623
3. Slide wave washer (7) onto through shaft bearing end (1).
4. Insert the races into the bores of shifter block plate (8).
5. Slide shifter block plate (8) onto through shaft bearing end (1).
Illustration 4 g00597624
2/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Slide bearing cone (9) onto through shaft bearing end (1).
Illustration 5 g00597625
7. Install locking washer (10) and bearing locknut (11) onto through shaft bearing end (1).
Note: Once proper clearance is obtained, bend the tabs of locking washer (10) into the slots
in bearing locknut (11). Proper clearance is 0.0254 mm to 0.0762 mm
(0.001 inch to 0.003 inch). The shifter block assembly should spin freely.
Hub − Assemble
Illustration 6 g00597501
1. Lubricate O-Ring (1) with a light film of oil and insert O-Ring (1) into the hub insert.
Note: Clean the O-Ring groove thoroughly before installing O-Ring (1) in order to prevent
leakage.
3/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00597503
2. Lubricate the shank of blade mounting shaft (2) with oil. Install nylon washer (3) onto blade
mounting shaft (2) and insert blade mounting shaft (2) into the hub insert.
Illustration 8 g00597506
3. Install the race of bearing (4) with the larger inside diameter onto blade mounting shaft (2).
4. Install the cage of bearing (4) onto blade mounting shaft (2).
5. Install the race of bearing (4) with the smaller inside diameter onto blade mounting shaft
(2).
Illustration 9 g00597507
4/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 6. Install collar (5) onto blade mounting shaft (2).
Note: The cut out of collar (5) should be facing upward.
Illustration 10 g00597508
7. Apply 9S-3263 Thread Lock Compound to capscrew (6). Install capscrew (6) into collar (5).
Hold blade mounting shaft (2) as you tighten capscrew (6). Tighten capscrew (6) to a torque
of 54 ± 5 N·m (40 ± 4 lb ft).
Illustration 11 g00597511
8. Repeat Steps 1 through 7 for each remaining blade mounting shaft.
5/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00597513
9. Remove capscrews (7) and front plate (8) from the shifter block assembly.
Illustration 13 g00597514
10. Remove two spacers (9).
Illustration 14 g00597515
11. Place pivot blocks (10) onto the pins of collars (5).
Illustration 15 g00597520
6/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 12. Position shifter block assembly (11) in the hub.
Note: Verify that the machined surfaces of pivot blocks (10) are against the flange surface.
Illustration 16 g00597523
13. Put spacers (9) into position over the corresponding holes.
14. Install ring (12) and align the holes with spacers (9).
Illustration 17 g00597526
15. Apply 9S-3263 Thread Lock Compound to capscrews (13A) and (13B) and install the
capscrews. Tighten capscrews (13A) to a torque of 16 ± 4 N·m (12 ± 3 lb ft). Tighten
capscrews (13B) to a torque of 34 ± 4 N·m (25 ± 3 lb ft).
Note: The shifter block assembly should move freely over the pivot blocks. If the shifter
block is binding, it is possible that a pivot block needs to be turned by 90 degrees.
7/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g00597527
16. Clean the groove in the hub that holds the O-Ring for the cover plate. Install O-Ring (14)
into the groove.
Illustration 19 g00597528
17. Place cover plate (15) onto the hub and align the holes.
18. Install capscrews (16). Do not put any 9S-3263 Thread Lock Compound on capscrews (16).
Tighten capscrews (16) to a torque of 16 ± 4 N·m (12 ± 3 lb ft).
Illustration 20 g00597530
8/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 19. Flip the hub assembly. Clean the groove in the hub that holds the O-Ring for the flange
plate. Install O-Ring (17) into the groove.
Illustration 21 g00597531
20. Place hub flange (18) onto the hub and align the holes.
Note: There is a small capscrew in the flange plate that aligns with a counterbore in the hub.
21. Install capscrews (19). Do not put any 9S-3263 Thread Lock Compound on capscrews (19).
Tighten capscrews (19) to a torque of 54 ± 5 N·m (40 ± 4 lb ft).
Actuator Bearings and Control Shaft Bushings − Install
Illustration 22 g00597972
1. Apply 4C-9507 Retaining Compound to bushing (1) and install bushing (1). The hole in
bushing (1) must line up with the hole in the bushing bore.
9/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g00597973
2. Install seals (2) and (3) so that the lips face outward.
Note: Some fans do not have seals (2) and (3).
Illustration 24 g00597975
3. Install all grease fittings and hoses.
Illustration 25 g00597977
4. Install spherical bearings (4) into actuator clevis (5).
10/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 26 g00597979
5. Put actuator collar (6) into position. Apply 9S-3263 Thread Lock Compound to the threads
of shoulder bolts (7) and install bolts (7). Tighten bolts (7) to a torque of 54 ± 5 N·m
(40 ± 4 lb ft).
Note: Actuator collar (6) must be installed so that the four setscrews face outward.
Frost Plug and Main Shaft O-Ring − Install
Illustration 27 g00598467
1. Temporarily install main shaft extension (1) into main shaft (2).
Note: Main shaft extension (1) must be removed during installation of the O-Ring.
11/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 28 g00598468
2. Use the former bushing as a template in order to create a slot in new bushing (3). Install new
bushing (3) into the rear of the main shaft.
Illustration 29 g00598469
3. Install bushing (4) into main shaft (2) or main shaft extension (1).
Note: Main shaft extension (1) may not be applicable in all cases. If this is true in your case,
bushing (4) will be required in main shaft (2).
Illustration 30 g00598470
12/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 4. Use the existing hole in bracket base (5) as a guide in order to drill a hole through the rear
bushing.
5. Clean the bore of the main shaft thoroughly. Verify that the bore for the internal O-Ring is
free of any foreign material.
Illustration 31 g00598471
6. Verify that through shaft (6) passes freely through both bushings (3) and (4).
Note: If through shaft (6) binds, reaming of bushings (3) and (4) may be required.
Illustration 32 g00598467
7. Remove main shaft extension (1) from main shaft (2).
13/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 33 g00598472
8. Use through shaft (6) in order to push O-Ring (7) into the groove inside main shaft (2).
Note: You may want to insert through shaft (6) into main shaft (2) from both sides in order
to verify that O-Ring (7) has seated properly.
Main Bearing Cups − Install
Illustration 34 g00598473
1. Install bearing cup (1) into bearing carrier (2).
14/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 35 g00598474
2. Install bearing cup (3) into the opposite side of bearing carrier (2).
3. Clean the bores of bearing cups (1) and (3). Verify that the grooves for the O-Rings are free
of any foreign material.
Carrier/Spool and Main Bearing − Install
Illustration 36 g00598600
1. Position bracket (1) so that main shaft (2) is vertical.
2. Slide fillet spacer (3) onto main shaft (2). The bevel on fillet spacer (3) must match the
radius on main shaft (2).
Note: Not all fan assemblies have fillet spacer (3).
3. Slide bearing cone (4) onto main shaft (2). Be careful not to damage the threads on main
shaft (2).
Illustration 37 g00598602
4. Set bearing carrier (5) on bearing cone (4).
5. Slide bearing spacer (6) onto main shaft (2).
15/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 38 g00598603
6. Slide shims (7) and (8) onto main shaft (2).
Illustration 39 g00598604
7. Slide bearing cone (9) onto main shaft (2). Thread bearing locknut (10) onto main shaft (2).
Tighten bearing locknut (10) to the correct torque. Refer to Table 1 for the correct torque.
Note: The use of a torque multiplier is recommended when you tighten bearing locknut
(10).
Table 1
Torque Values for Bearing Locknut (10)
Identification Inside Diameter Torque Value
N09 44.45 mm (1.75 inch) 230 ± 41 N·m (170 ± 30 lb ft)
N14 69.85 mm (2.75 inch) 353 ± 54 N·m (260 ± 40 lb ft)
8. Use a dial indicator to verify bearing clearance. Add or remove shims in order to obtain the
correct bearing clearance. Refer to Table 2 for the correct clearance.
Table 2
Bearing Clearances
16/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Inside Diameter Clearance
44.45 mm (1.75 inch) 0.025 mm to 0.076 mm (0.001 inch to 0.003 inch)
69.85 mm (2.75 inch) 0.076 mm to 0.127 mm (0.003 inch to 0.005 inch)
9. Remove all components except for fillet spacer (3) after the correct bearing clearance has
been obtained. The components will be reinstalled later in the procedure.
Illustration 40 g00598624
10. Place bearing carrier (5) so that the seal end faces upward.
11. Apply 4C-9507 Retaining Compound to the seal bore and the outside diameter of seal (11).
12. Place main bearing cone (12) into the cup. Press seal (11) into the seal bore of bearing
carrier (5) until the face of seal (11) is flush with the edge of bearing carrier (5).
13. Lubricate the double seal with oil.
Illustration 41 g00598607
14. Attach pulley (13) to bearing carrier (5) with capscrews (14). Tighten capscrews (14) to a
torque of 54 ± 5 N·m (40 ± 4 lb ft).
Note: Verify correct orientation of pulley (13).
17/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Illustration 42 g00598608
15. Position pulley (13) and bearing carrier (5) onto main shaft (2). Use care when you slide the
seal over the shoulder of the main shaft in order to not damage the seal. Be careful not to
damage the threads on the main shaft.
Illustration 43 g00598571
16. Install spacer (14) and shim (15). Shim (15) is the thinnest shim.
Illustration 44 g00598569
17. Install remaining shims (16) and bearing cone (17).
18/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 45 g00598568
18. Thread bearing locknut (18) onto main shaft (2) so that the end with the bevel faces away
from bearing cone (17). Tighten bearing locknut (18) to the correct torque. Refer to Table 3
for the correct torque.
Note: The use of a torque multiplier is recommended when you tighten bearing locknut
(18).
Table 3
Torque Values for Bearing Locknut (18)
Identification Inside Diameter Torque Value
N09 44.45 mm (1.75 inch) 230 ± 41 N·m (170 ± 30 lb ft)
N14 69.85 mm (2.75 inch) 353 ± 54 N·m (260 ± 40 lb ft)
Illustration 46 g00598567
19. Install locking washer (19). Install bearing locknut (20) so that the end with the bevel faces
toward bearing cone (17). Tighten bearing locknut (20) to the correct torque. Refer to Table
4 for the correct torque.
Note: Not all models of fan have two locknuts.
Table 4
19/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Torque Values for Bearing Locknut (20)
Identification Inside Diameter Torque Value
N09 44.45 mm (1.75 inch) 61 ± 11 N·m (45 ± 8 lb ft)
N14 69.85 mm (2.75 inch) 75 ± 11 N·m (55 ± 8 lb ft)
20. Bend the tabs of locking washer (19) into the slots in bearing locknut (20).
Illustration 47 g00598566
21. Apply 7M-7456 Compound to the threads of main shaft extension (21). Thread main shaft
extension (21) into main shaft (2). Tighten main shaft extension (21) to a torque of
136 ± 11 N·m (100 ± 8 lb ft).
Note: Not all fan assemblies have main shaft extension (21).
Illustration 48 g00598564
22. Inspect the groove for O-Ring (22) for any foreign material. Install O-Ring (22) into the
groove in bearing carrier (5). You can use grease in order to hold O-Ring (22) in place.
20/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 49 g00932665
23. Position spool (23) so that the bolt holes are aligned with the holes in bearing carrier (5).
Install capscrews (14).
Hub Kit − Install
Illustration 50 g00598711
1. Apply 9S-3263 Thread Lock Compound to the threads of through shaft bearing end (1).
Thread through shaft (2) onto through shaft bearing end (1).
2. Lubricate the entire length of through shaft (2) with a film of oil.
21/29938G Wheel Loader 6WS00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...