The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various transmission components on a Caterpillar 730C2 articulated truck, including:
1. Removing and installing the torque converter housing, which requires attaching lifting devices and brackets due to the housing's weight of approximately 500 lbs.
2. Removing and installing the pump drive, which also must be lifted due to its weight of 70 lbs, and includes removing O-rings from the housing.
3. Procedures for removing and installing the accessory drive, idler gear, and relief valve on the transmission, noting required tools and order of removal/installation steps.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for removing and installing components of the torque converter housing and pump drive on a Caterpillar 730C2 articulated truck. The removal procedure includes using lifting devices and tools to detach the torque converter housing and pump drive. Components like bolts, seals and manifolds are then removed from the housing and drive.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck. The instructions include removing the torque converter housing, pump drive, accessory drive, idler gear, and relief valve. Tools required are listed, along with torque specifications and other details needed to correctly complete the disassembly and reassembly procedures.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various transmission components on a Caterpillar 730C2 articulated truck, including:
1. Removing and installing the torque converter housing, which requires attaching lifting devices and brackets due to the housing's weight of approximately 500 lbs.
2. Removing and installing the pump drive, which also must be lifted due to its weight of 70 lbs, and includes removing O-rings from the housing.
3. Procedures for removing and installing the accessory drive, idler gear, and relief valve on the transmission, noting required tools and order of removal/installation steps.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for removing and installing components of the torque converter housing and pump drive on a Caterpillar 730C2 articulated truck. The removal procedure includes using lifting devices and tools to detach the torque converter housing and pump drive. Components like bolts, seals and manifolds are then removed from the housing and drive.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck. The instructions include removing the torque converter housing, pump drive, accessory drive, idler gear, and relief valve. Tools required are listed, along with torque specifications and other details needed to correctly complete the disassembly and reassembly procedures.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks involving hot coolant or fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks like working with pressurized coolant or fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure lists 11 steps to remove the rear gear group which includes removing bolts, seals, gears, bushings and bearings. The installation procedure provides 12 steps and specifies tools and torque specifications to install the components in reverse order. A separate section provides procedures for removing and installing the flywheel, which includes using lifting equipment and installing with loctite and torqueing bolts to the specified value.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides steps to install the rear crankshaft seal, gears, covers and flywheel in the reverse order of removal. Tools required are also listed.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new seal. The instructions cover engines with both a 14-bolt housing assembly and a 10-bolt housing assembly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts and the front housing, which contains gears and covers the camshaft.
2) Preparing and installing a new gasket and bolts to secure the front housing.
3) Ensuring proper alignment and torque specifications are followed for reinstallation.
This document provides instructions for removing and installing a steering cylinder on a 416D backhoe loader. It describes:
1. Removing the tie rods from the front axle. Removing the spanner nut and removing the steering cylinder assembly from the axle housing using a rubber mallet.
2. Disassembling the steering cylinder by removing retaining rings, seals, guides, and fittings.
3. Reassembling the steering cylinder by installing the parts in reverse order.
4. Installing the steering cylinder into the axle housing and installing the spanner nut and tie rods.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains information on engine systems, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments and headers, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for qualified dealership personnel and warns that anyone performing repairs without following the procedures could be responsible for damages.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists the required tools and parts and provides 43 steps and accompanying illustrations to assemble the torque converter. The steps include installing bearings, seals, gears, housings and other components. The final step is to connect the assembled torque converter housing to the planetary transmission.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual.pdfjfksemmdm3e
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
CASE IH WD2303 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains sections on the engine, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, and the platform, cab, bodywork, and decals. The introduction provides basic instructions for qualified dealership personnel on repair and maintenance work using the procedures in the manual.
This document provides instructions for removing and installing various components of a 3054C engine, including:
1) The crankshaft pulley, which is removed by taking out setscrews and the thrust block.
2) The crankshaft front seal, which is pulled out using a suitable puller to avoid damaging the housing.
3) The front cover, which is secured by setscrews and gasket and must be cleaned before installation.
More Related Content
Similar to Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2T400001 and up).pdf
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks involving hot coolant or fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks like working with pressurized coolant or fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure lists 11 steps to remove the rear gear group which includes removing bolts, seals, gears, bushings and bearings. The installation procedure provides 12 steps and specifies tools and torque specifications to install the components in reverse order. A separate section provides procedures for removing and installing the flywheel, which includes using lifting equipment and installing with loctite and torqueing bolts to the specified value.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides steps to install the rear crankshaft seal, gears, covers and flywheel in the reverse order of removal. Tools required are also listed.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
Similar to Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2T400001 and up).pdf (12)
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new seal. The instructions cover engines with both a 14-bolt housing assembly and a 10-bolt housing assembly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 3054C engine. It describes the required tools and parts, cleaning requirements, installation procedures including torque specifications, and references other documents for additional information.
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts and the front housing, which contains gears and covers the camshaft.
2) Preparing and installing a new gasket and bolts to secure the front housing.
3) Ensuring proper alignment and torque specifications are followed for reinstallation.
This document provides instructions for removing and installing a steering cylinder on a 416D backhoe loader. It describes:
1. Removing the tie rods from the front axle. Removing the spanner nut and removing the steering cylinder assembly from the axle housing using a rubber mallet.
2. Disassembling the steering cylinder by removing retaining rings, seals, guides, and fittings.
3. Reassembling the steering cylinder by installing the parts in reverse order.
4. Installing the steering cylinder into the axle housing and installing the spanner nut and tie rods.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains information on engine systems, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments and headers, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for qualified dealership personnel and warns that anyone performing repairs without following the procedures could be responsible for damages.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists the required tools and parts and provides 43 steps and accompanying illustrations to assemble the torque converter. The steps include installing bearings, seals, gears, housings and other components. The final step is to connect the assembled torque converter housing to the planetary transmission.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual.pdfjfksemmdm3e
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
CASE IH WD2303 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...jfksemmdm3e
This document is a service manual for Case IH self-propelled windrowers from PIN YCG667001 and above. It contains sections on the engine, front and rear axle systems, hydrostatic drive, power take-off, brakes and controls, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments/headers, and the platform, cab, bodywork, and decals. The introduction provides basic instructions for qualified dealership personnel on repair and maintenance work using the procedures in the manual.
This document provides instructions for removing and installing various components of a 3054C engine, including:
1) The crankshaft pulley, which is removed by taking out setscrews and the thrust block.
2) The crankshaft front seal, which is pulled out using a suitable puller to avoid damaging the housing.
3) The front cover, which is secured by setscrews and gasket and must be cleaned before installation.
This document provides assembly instructions for the transmission of a 416D Backhoe Loader. It includes notes on cleaning and preparation, lists required tools, and provides detailed step-by-step instructions and illustrations for assembling the transmission components in the following order: reverse shaft assembly, input shaft assembly, and shaft assembly. Precautions are given for lubrication, seals, and bearing installation temperatures.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the removal and installation steps. The removal process involves using a lifting device to remove the flywheel and housing, while installation requires heating the flywheel ring gear and using a press and alignment tool to correctly position the rear seal and housing. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. Removal of the flywheel requires loosening bolts and using a lifting device due to its weight of 53 kg. Installation of the crankshaft rear seal involves cleaning, lubricating, and pressing the seal into place using the proper tool. Proper torque values are also provided for reinstalling components.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054C engine. It describes:
1. Removing the electric starting motor and flywheel first.
2. Using link brackets as required tools to support the flywheel housing during removal and installation.
3. Removing bolts to separate the flywheel housing from the engine, and installing new bolts to secure the housing during reinstallation.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and gives step-by-step procedures for both removing and installing the seal. For engines with a 14-bolt housing, the instructions explain how to remove the housing, seal, and gasket before installing the new gasket and seal and reattaching the housing. For engines with a 10-bolt housing, the one-piece housing assembly is removed and installed as a unit.
The document provides instructions for removing and disassembling the valve mechanism cover, rocker shaft, and associated components of a Caterpillar C4.4 engine. It describes removing the valve mechanism cover and brackets. It then details using a tool to rotate the crankshaft and position the valves, loosening threaded inserts on the rocker arms, and removing the rocker shaft assembly and pushrods while marking their positions. Finally, it explains disassembling the rocker shaft assembly by removing screws, retaining clips, springs, and separating the rocker arm assemblies.
John Deere XUV 620i Gator Utility Vehicle Service Repair Manual.pdfjfksemmdm3e
This technical manual provides service and repair information for the John Deere Gator XUV 620i utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, maintenance, and repairs. It is intended as a resource for experienced technicians working with this product. Safety notices and procedures are highlighted throughout to warn of hazards during service.
John Deere XUV 850D Gator Utility Vehicle Service Repair Manual (tm1737).pdfjfksemmdm3e
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It aims to keep all information for a particular system together to aid technicians in servicing this vehicle. Safety is the first section and warns of dangers of fuel and working around heaters or other fire hazards.
This document provides instructions for removing and installing an engine in a 420F2 backhoe loader. It outlines 17 steps for removing the engine, which include disconnecting wiring harnesses, hoses, and other components. It then outlines 17 steps for installing the new engine, which involve connecting all the removed components in reverse order. Tools required include a hydraulic jack and load leveling beam to lift the heavy engine. Safety notices are provided to keep components clean and contain fluids.
The document provides instructions for removing and installing various components of the rear drive and steering axle assembly of a 420D backhoe loader, including:
- Removing the rear tires, drive shaft brackets, parking brake assembly, hydraulic hoses, manifold brackets, rear steer sensor wire, and axle mounting nuts and plates.
- Positioning a hydraulic jack under the axle and using a lifting device to remove the axle from the vehicle.
- Removing additional components from the axle including a parking brake bracket, cover, retaining clip, pin and washer.
The procedures include illustrations of each step and require tools such as a puller, wrench, heat gun and hydraulic jack. Safety notices
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i07526804
Torque Converter Housing - Install
SMCS - 3105-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B - Loctite 242 -
C 385-4000 Seal Installation Tool 1
D - Loctite Flange Sealant 5900 -
Illustration 1 g03129265
1. Install studs (9) if removed. Install seal (8).
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g03129058
Illustration 3 g03129157
2. Attach Tooling (A) and a suitable lifting device to torque converter housing. The weight of
torque converter housing (5) is approximately 227 kg (500 lb). Install torque converter
housing (5).
3. Apply Tooling (D) to the housing spotface and washer of bolt (7).
Note: Remove excess sealant after bolt (7) is torqued.
4. Install bolt (7). Apply Tooling (B) to the threads of studs (9). Install nuts (6). Tighten bolt
(7) and nuts (6) to a torque of 100 ± 20 N·m (74 ± 15 lb ft).
2/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g03129025
5. Connect harness assembly and cable strap (4).
Illustration 5 g03129017
6. Connect harness assembly (2) and cable straps (3).
Illustration 6 g03128943
7. Use Tooling (C) and Install lip seal (1) dry.
End By:
a. Install the gear pump (scavenge transmission).
b. Install the torque converter.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:48:04 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947892
Relief Valve (Torque Converter Inlet) - Remove and Install
SMCS - 3133-010-OL
Removal Procedure
Start By:
a. Remove the pump drive.
Illustration 1 g03141720
1. Remove bolts (1) and bolt (3). Remove manifold (2).
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g01228580
2. Install relief valve (5). Install retaining ring (4).
Illustration 6 g03141720
3. Position manifold (2). Install bolts (1) and bolt (3).
End By:
a. Install the pump drive.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:49:00 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04954722
Accessory Drive (Transmission) - Remove and Install
SMCS - 1207-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Illustration 1 g03140318
1. Remove bolts (1). Remove cover (2) and the O-ring seal.
1/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g03140345
Illustration 3 g03140420
2. Remove bolts (3) from adapter (4). Use bolts (3) to remove adapter (4).
Illustration 4 g03141316
3. Remove O-ring seal (5) and shims (6).
2/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 5 g03141378
4. Use Tooling (A) and a suitable press to remove bearing cup (7).
Illustration 6 g03141418
5. Remove gear assembly (8).
Illustration 7 g03141456
6. Remove bearing cones (9) and seal (10).
3/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 8 g03141469
7. Remove bearing cup (11).
Installation Procedure
Illustration 9 g03141517
1. Install bearing cup (11).
Illustration 10 g03141456
2. Raise the temperature of bearing cones (9) to install. Install seal (10).
4/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 11 g03141418
3. Install gear assembly (8).
Illustration 12 g03141540
4. Use Tooling (A) and suitable press to install bearing cup (7).
Illustration 13 g03141316
5. Install required shims (6) to obtain 0.1 mm (0.00394 inch) to 0.2 mm (0.00787 inch) end
play. Install O-ring seal (5) and lubricate with lubricant being sealed.
5/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 14 g03140345
6. Position adapter (4) and install bolts (3).
Illustration 15 g03140318
7. Position cover (2) and the O-ring seal. Install bolts (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:49:56 UTC+0800 2019
6/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04954150
Idler Gear (Transmission Accessory Drive) - Remove and
Install
SMCS - 1234-010
Removal Procedure
Start By:
a. Remove the pump drive.
Illustration 1 g03137780
1. Remove bolts (5) and remove cover and O-ring seal (4). Remove bolt (3) and washer (2).
2. Remove shaft (1) and remove idler gear (6) from the housing.
1/2
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g03139696
3. Remove bearing (7).
Installation Procedure
1. Install idler gear (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:50:51 UTC+0800 2019
2/2
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947209
Pump Drive - Remove
SMCS - 3108-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the torque converter housing.
Illustration 1 g03133076
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. 1. Attach Tooling (A) and a suitable lifting device to torque converter housing (1). The weight
of torque converter housing (1) is approximately 227 kg (500 lb). Position torque converter
housing (1) on to Tooling (B).
Illustration 2 g01231807
2. Remove bolts (2) and shield assembly (3).
Illustration 3 g03133357
3. Attach Tooling (A) and a suitable lifting device to pump drive (4). The weight of pump
drive (4) is approximately 32 kg (70 lb). Remove bolts (5) and (6). Remove pump drive (4).
Illustration 4 g03133457
2/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Remove O-ring seals (7) from torque converter housing (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:51:47 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947514
Pump Drive - Disassemble
SMCS - 3108-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
289-2838 Spanner 1
289-2846 Spline Wrench 1
C 8T-4184 Bolt 3
D -
Flat Stock Steel
1/16 - 3/4 by 8
2
Start By:
a. Remove the pump drive.
1/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g03133996
1. Remove ten bolts (1) and bolt (3). Remove manifold (2).
Illustration 2 g01231869
2. Use Tooling (A) in order to remove race (4) from manifold (2).
Illustration 3 g01231871
3. Remove carrier assembly (6) from manifold (5).
2/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...