This document provides instructions for disassembling and assembling the torque converter of a 627G Wheel Scraper. The disassembly process involves using various tools to remove over 30 individual components in a specific sequence. The assembly section then lists the reverse steps, providing guidance on cleaning parts and installing components in the correct order while maintaining proper temperatures and torques.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides instructions for disassembling a torque converter for a 637G wheel tractor. It lists 32 steps to completely disassemble the torque converter including removing retaining rings, gears, shafts, seals, bearings, and housing components. Tools required are also listed. The assembly instructions are then provided in 31 steps to reassemble all components back into the torque converter.
This document provides instructions for disassembling a torque converter for a 637G wheel tractor. It lists 32 steps to completely disassemble the torque converter including removing retaining rings, gears, shafts, seals, bearings, and housing components. Tools required are also listed. The assembly instructions are then provided in 31 steps to reassemble all components in reverse order.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
This document provides instructions for disassembling a torque converter for a 637G wheel tractor. It lists 32 steps to completely disassemble the torque converter including removing retaining rings, gears, shafts, seals, bearings, and housing components. Tools required are also listed. The assembly instructions are then provided in 31 steps to reassemble all components back into the torque converter.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides instructions for disassembling a torque converter for a 637G wheel tractor. It lists 32 steps to completely disassemble the torque converter including removing retaining rings, gears, shafts, seals, bearings, and housing components. Tools required are also listed. The assembly instructions are then provided in 31 steps to reassemble all components back into the torque converter.
This document provides instructions for disassembling a torque converter for a 637G wheel tractor. It lists 32 steps to completely disassemble the torque converter including removing retaining rings, gears, shafts, seals, bearings, and housing components. Tools required are also listed. The assembly instructions are then provided in 31 steps to reassemble all components in reverse order.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
This document provides instructions for disassembling a torque converter for a 637G wheel tractor. It lists 32 steps to completely disassemble the torque converter including removing retaining rings, gears, shafts, seals, bearings, and housing components. Tools required are also listed. The assembly instructions are then provided in 31 steps to reassemble all components back into the torque converter.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before disassembling the recoil spring components.
3. Reassembling the recoil spring components and using the tooling bench to apply controlled compression for assembly. Proper centering and leveling of the assembly is critical.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 657E wheel tractor. The removal procedure involves using various tools to disassemble the rear gear components and adapter assemblies. The installation procedure describes reassembling these components and requires pressing or installing bearings and seals using a driver group or press. Special care must be taken to keep parts clean and lubricated. The flywheel removal uses tools to secure the crankshaft gear and hoist the heavy flywheel off the engine.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using punch tools or pullers
The document provides instructions for installing the crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes heating the ring gear to 300°C before installing it on the flywheel. It also details installing guide bolts and lifting brackets to position the flywheel, applying grease to the bolt threads, and torquing the bolts to secure the flywheel. Finally, it notes to check the flywheel runout after installation.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified torques and clearances. Precautions are provided such as cleaning and lubricating parts during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling various components of a 651B wheel scraper model, including:
1. The engine transfer gear and retarder, with steps to remove gears, bearings, and housing pieces.
2. The transmission transfer gear, with steps to remove gears, bearings, pumps, and the governor.
3. The transmission governor, with identification of parts and steps to disassemble and reassemble the governor valve bodies.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before disassembling the recoil spring components.
3. Reassembling the recoil spring components and using the tooling bench to apply controlled compression for assembly. Proper centering and leveling of the assembly is critical.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 657E wheel tractor. The removal procedure involves using various tools to disassemble the rear gear components and adapter assemblies. The installation procedure describes reassembling these components and requires pressing or installing bearings and seals using a driver group or press. Special care must be taken to keep parts clean and lubricated. The flywheel removal uses tools to secure the crankshaft gear and hoist the heavy flywheel off the engine.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using punch tools or pullers
The document provides instructions for installing the crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes heating the ring gear to 300°C before installing it on the flywheel. It also details installing guide bolts and lifting brackets to position the flywheel, applying grease to the bolt threads, and torquing the bolts to secure the flywheel. Finally, it notes to check the flywheel runout after installation.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified torques and clearances. Precautions are provided such as cleaning and lubricating parts during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling various components of a 651B wheel scraper model, including:
1. The engine transfer gear and retarder, with steps to remove gears, bearings, and housing pieces.
2. The transmission transfer gear, with steps to remove gears, bearings, pumps, and the governor.
3. The transmission governor, with identification of parts and steps to disassemble and reassemble the governor valve bodies.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 627G WHEEL SCRAPER CEZ
Configuration: 627G Wheel Scraper CEZ00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
627G Wheel Scraper Power Train
Media Number -RENR4232-02 Publication Date -01/03/2004 Date Updated -09/03/2018
i04332691
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-1861 Retaining Ring Pliers 1
C 1P-0520 Driver Gp 1
D 2P-8312
Retaining Ring Pliers
(External)
1
E 8H-0663
Bearing Puller Gp
(Nine Ton Capacity)
1
F
1P-2322
Combination Puller
(Two Jaw or Three Jaw)
1
1P-0546 Puller Jaw 1
1P-0510 Driver Gp 1
Start By:
a. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter, Transmission and Transfer Gear - Separate".
NOTICE
1/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00833596
1. Remove retaining ring (1). Remove retarder rotor (2).
Illustration 2 g00833624
2. Remove seal ring (4) from carrier (3) on each side of retarder rotor (2).
3. Remove carrier (3).
Note: The carrier will be destroyed when the carrier is removed from the retarder.
2/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Illustration 3 g00833629
4. Remove bolts (5). Remove race (6).
Illustration 4 g00833647
5. Attach Tooling (A) and a suitable lifting device to housing assembly (7). The weight of
housing assembly (7) is approximately 73 kg (160 lb).
6. Remove housing assembly (7) from the torque converter.
Illustration 5 g00833655
7. Position housing assembly (7), as shown.
3/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. 8. Remove bolts (9). Remove gear (8).
Illustration 6 g00833666
9. Use Tooling (B) to remove retaining ring (10) from each side of gear (8).
Illustration 7 g00833676
10. Remove shaft (11).
Illustration 8 g00833678
11. Use a suitable press and Tooling (C) to remove the bearing from gear (8).
4/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 12 g00837274
Illustration 13 g00837280
Illustration 14 g01160859
15. Remove retainer (17) from shaft (22). Remove ring seals (18).
16. Remove gear (19) from shaft (22).
17. Remove bolts (20) and retainer (21). Use Tooling (D) to remove retaining ring (23).
6/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Illustration 15 g01160895
18. Position the torque converter, as shown. Remove bolts (24).
Illustration 16 g01160896
19. Attach Tooling (A) and a suitable lifting device to impeller assembly (25). The weight of
impeller assembly (25) is approximately 41 kg (90 lb).
20. Remove impeller assembly (25) from housing (26).
Illustration 17 g01160897
21. Remove retaining ring (27) and the bearing.
7/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 18 g01160860
22. Use Tooling (F) to separate shaft (22) from carrier assembly (28) and the bearing. Remove
the bearing.
Illustration 19 g00837179
23. Remove bolts (29). Remove stator assembly (31) from impeller (30).
Illustration 20 g01160933
8/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 21 g01160931
24. Remove bolts (32) from gear (33).
25. Use Tooling (B) to drive carrier assembly (28) and gear (33) out of impeller (30).
Illustration 22 g00837205
26. Use Tooling (B) to drive carrier (34) out of impeller (30).
Illustration 23 g01054015
27. Use Tooling (B) to drive carrier assembly (28) out of bearing (35).
9/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 24 g01054017
28. Remove gear (33) from carrier assembly (28).
Illustration 25 g01054020
29. Remove seal ring (36).
Illustration 26 g01160861
30. Remove rings (37). Use Tooling (D) to remove ring (38) from shaft (22).
10/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 27 g01160862
31. Install Tooling (E). Tooling (E) must be seated on the shoulders of turbine (39). Tooling (E)
must not contact the splines on shaft (22).
Note: Tooling (E) must be used in order to support turbine (39) or damage to turbine (39)
will result.
Illustration 28 g01160863
32. Use a suitable press to remove shaft (22) from turbine (39). Remove bearing race (40) and
the spacer from turbine (39).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 9 19:56:41 UTC+0800 2021
11/11(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 627G WHEEL SCRAPER CEZ
Configuration: 627G Wheel Scraper CEZ00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
627G Wheel Scraper Power Train
Media Number -RENR4232-02 Publication Date -01/03/2004 Date Updated -09/03/2018
i02322407
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-1861 Retaining Ring Pliers 1
C 1P-0520 Driver Gp 1
D 2P-8312
Retaining Ring Pliers
(External)
1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 1 g01160861
1. Lower the temperature of shaft (22). Use Tooling (D) to install ring (38). Install shaft (22) in
the turbine until ring (38) rests on the turbine. Install rings (37).
Illustration 2 g01160941
2. Install the spacer. Raise the temperature of bearing race (40). Install bearing race (40) to
turbine (39) and shaft (22).
Illustration 3 g01054020
3. Install seal ring (36).
2/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 4 g01054017
4. Install gear (33) to carrier assembly (28).
Illustration 5 g01054015
5. Raise the temperature of bearing (35). Install bearing (35) on carrier assembly (28).
Illustration 6 g00837205
6. Lower the temperature of carrier (34). Install carrier (34) into impeller (30).
Note: Make sure that the bolt holes are aligned.
3/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 7 g00837194
7. Position gear (33). Install bolts (32). Tighten bolts (32) to a torque of 50 ± 7 N·m
(37 ± 5 lb ft).
Illustration 8 g00837179
8. Position stator assembly (31) on impeller (30) and on carrier assembly (28). Install bolts
(29). Tighten bolts (29) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
Illustration 9 g01160943
9. Install carrier assembly (28) on impeller (39).
4/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 10. Raise the temperature of the bearing. Install the bearing on shaft (22).
Illustration 10 g01160897
11. Lower the temperature of the bearing. Install the bearing. Install retaining ring (27).
Illustration 11 g01160896
12. Use Tooling (A) and a suitable lifting device to install impeller assembly (25) to housing
(26). The weight of impeller assembly (25) is approximately 41 kg (90 lb).
Illustration 12 g01160895
5/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. 13. Position the torque converter, as shown. Install bolts (24). Tighten bolts (24) to a torque of
30 ± 5 N·m (22 ± 4 lb ft).
Illustration 13 g01160859
Illustration 14 g00837280
Illustration 15 g00837274
14. Use Tooling (D) to install retaining ring (23). Position retainer (21). Install bolts (20).
Tighten bolts (20) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
15. Install gear (19) on shaft (22).
6/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. 20. Install bolts (12). Tighten bolts (12) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 19 g00833678
21. Use a suitable press and Tooling (C) to install the bearing to gear (8).
Illustration 20 g00833676
22. Install shaft (11).
Illustration 21 g00833666
23. Use Tooling (B) to install retaining ring (10) on each side of gear (8).
8/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 22 g00833655
24. Position housing assembly (7), as shown.
25. Position gear (8). Install bolts (9).
Illustration 23 g00833647
26. Attach Tooling (A) and a suitable lifting device to housing assembly (7). The weight of
housing assembly (7) is approximately 73 kg (160 lb).
27. Install housing assembly (7) onto the torque converter.
Illustration 24 g00833629
9/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. 28. Install race (6). Install bolts (5).
Illustration 25 g00833624
29. Install carrier (3).
30. Install seal ring (4) to carrier (3) on each side of retarder rotor (2).
Illustration 26 g00833596
31. Install retarder rotor (2). Install retaining ring (1).
End By:
a. Connect the torque converter to the transmission. Refer to Disassembly and Assembly,
"Torque Converter, Transmission and Transfer Gear - Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 9 19:57:37 UTC+0800 2021
10/10(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 627G WHEEL SCRAPER CEZ
Configuration: 627G Wheel Scraper CEZ00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
627G Wheel Scraper Power Train
Media Number -RENR4232-02 Publication Date -01/03/2004 Date Updated -09/03/2018
i02331325
Transfer Gears - Disassemble
SMCS - 3159-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
1P-0820 Hydraulic Puller 1
3H-0465 Push-Puller Plate 4
8B-7549 Puller Leg 2
8B-7551 Bearing Puller Gp 1
C 138-7573 Link Bracket 2
D
5F-7343
Bearing Puller Gp
(Twenty Ton Capacity)
1
1P-0520 Driver Gp 1
E
8B-7551 Bearing Puller Gp 1
1P-0520 Driver Gp 1
Start By:
A. Remove the transmission. Refer to Disassembly and Assembly, "Torque Converter,
Transmission, and Transfer Gear - Separate".
1/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00834630
1. Remove cover (1) .
2/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. 5. Position cage assembly (3). Remove bolts (8). Remove plate (9). Remove O-ring seal (10) .
Illustration 5 g00834589
Illustration 6 g00834834
6. Use Tooling (A) and a suitable press in order to remove bearings (11) from cage assembly
(3) .
4/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. Illustration 7 g00834594
Note: If the shaft is not supported, the shaft will fall when bolt (13) is removed.
7. Position transfer case (12). Support shaft (14). Remove bolt (13). Remove the retainer.
Remove shaft (14) .
8. Remove gear (15) from transfer case (12) .
Illustration 8 g00834598
9. Use Tooling (B) in order to remove bearing (16) from shaft (14) .
Illustration 9 g00834608
10. Remove bolts (17) .
5/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
28. Illustration 10 g00834615
11. Attach Tooling (C) and a suitable lifting device to cage (18). Remove cage (18) and the
pinion as a unit. The weight of cage (18) and the pinion is approximately 34 kg (76 lb).
Illustration 11 g00834620
12. Remove bolts (19). Remove plate (20). Remove bearing cone (21) .
Illustration 12 g00834621
6/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
29. 13. Use Tooling (D) and a suitable press in order to remove cage (18) from pinion (22) .
Illustration 13 g00834623
14. If necessary, use Tooling (E) in order to remove bearing cone (23) from pinion (22). If
necessary, use Tooling (E) in order to remove bearing cone (24) from pinion (22) .
Illustration 14 g00834625
15. Remove retaining ring (25) in order to remove bearing cup (26) from cage (18) .
7/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
30. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
31. Illustration 15 g00834626
16. Use Tooling (A) and a suitable press in order to remove the bearing cup from cage (18) .
Illustration 16 g00834628
17. Remove plug (27). Remove the dowel that holds the race in position.
Illustration 17 g00834629
18. Remove bearing race (28). Remove bearing race (29) .
8/9(W)
w
2021/5/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...