This document provides instructions for disassembling and assembling the transmission hydraulic control valve of a 637G wheel scraper. The disassembly procedure involves removing 19 parts in 19 steps, taking care with springs. The assembly procedure involves assembling the 19 parts in 19 steps, also taking care with springs. Tools include retaining ring pliers. Proper cleaning is emphasized to prevent hydraulic system contamination.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Caterpillar Cat CS-423E Vibratory Compactor (Prefix CFX) Service Repair Manua...fjkskkedmm4r
This document provides assembly instructions for the axle on a CS-423E vibratory compactor. It details 33 steps to assemble components such as the differential, wheel hubs, brakes, and gearbox. Tools and torque specifications are listed. Parts are cleaned and seals/bearings replaced if damaged before assembly. Components like the differential, wheel hubs, brakes, and gearbox are assembled separately then installed on the axle housing.
Caterpillar Cat CS-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Volvo EC55-2 Compact Excavator Parts Catalogue Manual – SN 5001 - 7620.pdffjkskkedmm4r
This document contains specifications for various engine parts for a Volvo EC55-2 engine. It includes sections for the engine, cylinder head, valves, pistons, connecting rods, camshaft, and other components. Each section lists the relevant part numbers, descriptions, quantities, and other details. The document provides an extensive catalogue of replacement parts for this engine model.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...fjkskkedmm4r
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Pictures and diagrams show the layout and connections between various hydraulic system parts.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Caterpillar Cat CS-423E Vibratory Compactor (Prefix CFX) Service Repair Manua...fjkskkedmm4r
This document provides assembly instructions for the axle on a CS-423E vibratory compactor. It details 33 steps to assemble components such as the differential, wheel hubs, brakes, and gearbox. Tools and torque specifications are listed. Parts are cleaned and seals/bearings replaced if damaged before assembly. Components like the differential, wheel hubs, brakes, and gearbox are assembled separately then installed on the axle housing.
Caterpillar Cat CS-433E Vibratory Compactor (Prefix BTY) Service Repair Manua...fjkskkedmm4r
This document provides instructions for disassembling and assembling the piston motor (axle propel) of a CP-433E vibratory compactor. The disassembly procedure involves removing 21 components from the housing in a specific order, taking care with spring-loaded parts. The assembly procedure reverses this process in 23 steps, ensuring proper installation of seals, bearings, pins and other components back into their original positions in the housing. Special tools and torque specifications are listed to correctly perform the work.
Volvo EC55-2 Compact Excavator Parts Catalogue Manual – SN 5001 - 7620.pdffjkskkedmm4r
This document contains specifications for various engine parts for a Volvo EC55-2 engine. It includes sections for the engine, cylinder head, valves, pistons, connecting rods, camshaft, and other components. Each section lists the relevant part numbers, descriptions, quantities, and other details. The document provides an extensive catalogue of replacement parts for this engine model.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...fjkskkedmm4r
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Pictures and diagrams show the layout and connections between various hydraulic system parts.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
JCB 4CX444 (Sideshift AA AB Engine) BACKOHE LOADER Parts Catalogue Manual (Se...fjkskkedmm4r
This document contains parts listings and diagrams for engine components of a backhoe loader, including:
1. The block assembly diagram lists parts such as the cylinder block, liners, plugs, bolts, and rear seal housing.
2. The crankshaft assembly diagram lists the crankshaft, bearing kits, thrust washers, connecting rod assemblies, pistons, rings, and gears.
3. The document provides additional diagrams for components like the timing case, flywheel, and engine mountings. The parts are identified by part number, description, and quantity for various engine builds.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
1. The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the spacer plate, valves, valve seat inserts, bridge dowels, valve guides, oil pan and plate, oil pump, and piston cooling tubes.
2. The instructions describe cleaning and preparing surfaces, using specific tools to remove and install components, and ensuring proper installation and operation after reassembly.
3. The overall process involves removing engine components, cleaning surfaces, installing new parts as needed, and reassembling the engine, with the goal of properly servicing the 3406C diesel engine.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
1. Remove the transmission, torque converter, and transfer gears from the tractor. Lift the assembly weighing approximately 1320 kg onto stands.
2. Attach lifting brackets and remove the bolts and nuts securing the 340 kg transfer gears to the transmission. Separate the transfer gears and remove o-rings.
3. Remove the final o-ring seal from the transmission. Install the transfer gears by reversing the removal steps.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and refastening housings and covers.
This document provides step-by-step instructions to disassemble a piston pump. It begins by removing the piston pump and cleaning it. Key components like the piston assemblies, barrel assembly, springs and seals are then removed. Precision tools are required to remove parts like bearings and seals without damage. The multi-stage process dismantles both sides of the pump housing and internal components like valves, solenoids and control blocks are broken down. Precise part tracking and cleanliness are emphasized for reassembly.
This document provides instructions for disassembling and assembling bevel and transfer gears on a D6M track-type tractor. It outlines 22 steps for disassembly, which include removing brackets, yokes, carriers, cages, seals, bearings, gears, pins, shafts, and other components. It then outlines 21 steps for assembly, which involve cleaning parts, installing bearings, gears, pins, shafts, seals, covers, and other components in the reverse order of disassembly. Proper tools and cleaning procedures are emphasized to prevent damage to components from dirt and contaminants.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D6N track-type tractor. It describes removing the final drive, steering clutch, and brake as separate components. It then details each step to disassemble the steering clutch and brake parts and housing. The corresponding assembly instructions are also provided in reverse order.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head. The procedures include removing and installing the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, valve guides, and oil pan and plate. The instructions describe the specific steps to disassemble and reassemble each component.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides instructions for disassembling and assembling components of the retarder and bearing cage (drive shaft) of a 623G wheel tractor. The disassembly procedure involves using various tools to remove 15 different components. The assembly procedure instructs installing the components in reverse order and refers to other documents for installing related components. Safety notices are provided regarding containing fluids and preventing contamination.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...fjkskkedmm4r
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
Caterpillar Cat CB-335E Vibratory Compactor (Prefix C3F) Service Repair Manua...fjkskkedmm4r
This document provides instructions for removing the drum and drum support from a CB-335E vibratory compactor. It involves:
1. Removing the vibratory motor.
2. Disconnecting the water supply hose from the spray bar and removing the scraper and spray bar assembly.
3. Removing the drum support bolts and lifting the drum and drum support from the machine using lifting beams.
Caterpillar Cat CB-334E Vibratory Compactor (Prefix C3F) Service Repair Manua...fjkskkedmm4r
This document provides instructions for removing the drum and drum support from a CB-335E vibratory compactor. It involves:
1. Removing the vibratory motor.
2. Disconnecting the water supply hose from the spray bar and removing the scraper and spray bar assembly.
3. Removing the drum support bolts and lifting the drum and drum support from the machine using lifting beams.
Caterpillar Cat 980G II Wheel Loader (Prefix AXG) Service Repair Manual (AXG0...fjkskkedmm4r
This document provides instructions for removing and installing a valve mechanism cover and valve mechanism cover base on a Caterpillar 3406E engine. The procedure involves:
1. Removing bolts to remove the valve mechanism cover.
2. Cleaning old gasket material and installing a new gasket when reinstalling the cover.
3. Removing bolts and other hardware to remove the valve mechanism cover base. Cleaning and installing new seals when reinstalling.
The instructions provide illustrations and specify torque values for fasteners. Proper cleaning and use of new seals/gaskets is emphasized.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
Caterpillar Cat 980G II WHEEL LOADER (Prefix AYT) Service Repair Manual (AYT0...fjkskkedmm4r
This document provides instructions to disassemble and assemble the freewheel stator component of a 980G Series II wheel loader power train. It outlines 56 steps to remove components such as bearings, seals, gears, and housings. Tools required include link brackets, push-pullers, bearing puller attachments, drivers, and retaining ring pliers. Cleanliness is important during assembly and all parts should be inspected and replaced if worn or damaged.
1. The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the spacer plate, valves, valve seat inserts, bridge dowels, valve guides, oil pan and plate, oil pump, and piston cooling tubes.
2. The instructions describe cleaning and preparing surfaces, using specific tools to remove and install components, and ensuring proper installation and operation after reassembly.
3. The overall process involves removing engine components, cleaning surfaces, installing new parts as needed, and reassembling the engine, with the goal of properly servicing the 3406C diesel engine.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
1. Remove the transmission, torque converter, and transfer gears from the tractor. Lift the assembly weighing approximately 1320 kg onto stands.
2. Attach lifting brackets and remove the bolts and nuts securing the 340 kg transfer gears to the transmission. Separate the transfer gears and remove o-rings.
3. Remove the final o-ring seal from the transmission. Install the transfer gears by reversing the removal steps.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and refastening housings and covers.
This document provides step-by-step instructions to disassemble a piston pump. It begins by removing the piston pump and cleaning it. Key components like the piston assemblies, barrel assembly, springs and seals are then removed. Precision tools are required to remove parts like bearings and seals without damage. The multi-stage process dismantles both sides of the pump housing and internal components like valves, solenoids and control blocks are broken down. Precise part tracking and cleanliness are emphasized for reassembly.
This document provides instructions for disassembling and assembling bevel and transfer gears on a D6M track-type tractor. It outlines 22 steps for disassembly, which include removing brackets, yokes, carriers, cages, seals, bearings, gears, pins, shafts, and other components. It then outlines 21 steps for assembly, which involve cleaning parts, installing bearings, gears, pins, shafts, seals, covers, and other components in the reverse order of disassembly. Proper tools and cleaning procedures are emphasized to prevent damage to components from dirt and contaminants.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D6N track-type tractor. It describes removing the final drive, steering clutch, and brake as separate components. It then details each step to disassemble the steering clutch and brake parts and housing. The corresponding assembly instructions are also provided in reverse order.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head. The procedures include removing and installing the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, valve guides, and oil pan and plate. The instructions describe the specific steps to disassemble and reassemble each component.
This document provides disassembly and assembly instructions for a 3406C engine governor. It begins with removing the fuel injection pump housing and governor. It then provides 37 detailed steps for disassembling the governor components. The assembly section provides 43 steps for reassembling the governor in reverse order.
This document provides instructions for disassembling and assembling components of the retarder and bearing cage (drive shaft) of a 623G wheel tractor. The disassembly procedure involves using various tools to remove 15 different components. The assembly procedure instructs installing the components in reverse order and refers to other documents for installing related components. Safety notices are provided regarding containing fluids and preventing contamination.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...fjkskkedmm4r
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate internal components like pistons, plates and barrels.
Caterpillar Cat CB-335E Vibratory Compactor (Prefix C3F) Service Repair Manua...fjkskkedmm4r
This document provides instructions for removing the drum and drum support from a CB-335E vibratory compactor. It involves:
1. Removing the vibratory motor.
2. Disconnecting the water supply hose from the spray bar and removing the scraper and spray bar assembly.
3. Removing the drum support bolts and lifting the drum and drum support from the machine using lifting beams.
Caterpillar Cat CB-334E Vibratory Compactor (Prefix C3F) Service Repair Manua...fjkskkedmm4r
This document provides instructions for removing the drum and drum support from a CB-335E vibratory compactor. It involves:
1. Removing the vibratory motor.
2. Disconnecting the water supply hose from the spray bar and removing the scraper and spray bar assembly.
3. Removing the drum support bolts and lifting the drum and drum support from the machine using lifting beams.
Caterpillar Cat 980G II Wheel Loader (Prefix AXG) Service Repair Manual (AXG0...fjkskkedmm4r
This document provides instructions for removing and installing a valve mechanism cover and valve mechanism cover base on a Caterpillar 3406E engine. The procedure involves:
1. Removing bolts to remove the valve mechanism cover.
2. Cleaning old gasket material and installing a new gasket when reinstalling the cover.
3. Removing bolts and other hardware to remove the valve mechanism cover base. Cleaning and installing new seals when reinstalling.
The instructions provide illustrations and specify torque values for fasteners. Proper cleaning and use of new seals/gaskets is emphasized.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
Caterpillar Cat 980G II WHEEL LOADER (Prefix AYT) Service Repair Manual (AYT0...fjkskkedmm4r
This document provides instructions to disassemble and assemble the freewheel stator component of a 980G Series II wheel loader power train. It outlines 56 steps to remove components such as bearings, seals, gears, and housings. Tools required include link brackets, push-pullers, bearing puller attachments, drivers, and retaining ring pliers. Cleanliness is important during assembly and all parts should be inspected and replaced if worn or damaged.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at Multifamily Properties by Kevin Donnelly
Caterpillar Cat 637G WHEEL SCRAPER (Prefix AWE) Service Repair Manual (AWE00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i02310162
Transmission Hydraulic Control Valve - Disassemble
SMCS - 3073-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 1P-1853 Retaining Ring Pliers 1
Start By:
a. Remove the transmission hydraulic control valve. Refer to Disassembly and Assembly,
"Transmission Hydraulic Control Valve - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
2. Note: Hold each cover securely in order to contain the spring pressure when you remove the
bolts.
Illustration 1 g01096879
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (3) from cover (1).
2. Remove bolts (2A) from cover (2).
Illustration 2 g01034814
3. Remove cover (1) and cover (2). Remove piston (4). Remove spool (5).
2/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 3 g01034815
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove piston (4), spring (6), and spring (7). Remove spacers (8).
5. Remove slug (13).
6. Use Tooling (A) in order to remove retaining ring (12).
7. Remove retainer (11). Remove spring (10).
8. Remove plunger (9) from spool (5).
Illustration 4 g00822724
3/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 9. Remove spool (14). Remove stop (15).
10. Remove spring (16).
11. Remove slug (20) and remove spool (19).
12. Remove spring (18). Remove washer (17).
Illustration 5 g01096790
13. Remove load spool (21). Remove speed spool (22).
Illustration 6 g01096791
14. If necessary, loosen locknuts (24) and remove links (23) from spools (21) and (22).
4/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 7 g01096792
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: Hold the cover securely in order to contain the spring pressure when you remove the
bolts.
15. Remove bolts (25) and cover (26).
Illustration 8 g01096793
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
16. Remove spring (29) and spool assembly (30).
17. Use Tooling (A) to remove retaining ring (34) from spool (30).
5/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 18. Remove retainer (33), spring (32), and plunger (31).
19. If necessary, remove dowel (27) and remove stop (28).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:31:04 UTC+0800 2021
6/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i02310163
Transmission Hydraulic Control Valve - Assemble
SMCS - 3073-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 1P-1853 Retaining Ring Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g01096793
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. If necessary, install dowel (27) and install stop (28).
2. Install retainer (33), spring (32), and plunger (31).
3. Use Tooling (A) to install retaining ring (34) onto spool (30).
4. Install spring (29) and spool assembly (30).
Illustration 2 g01096792
2/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Hold the cover securely while you install the bolts.
5. Position cover (26). Install bolts (25). Tighten bolts (25) to a torque of 30 ± 4 N·m
(22 ± 3 lb ft).
Illustration 3 g01096791
6. If necessary, install links (23) and tighten locknuts (24) onto spools (21) and (22).
Illustration 4 g01096790
7. Install load spool (21). Install speed spool (22).
3/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 5 g00822724
8. Install spool (19). Install slug (20).
9. Install spring (18). Install washer (17).
10. Install spring (16).
11. Install spool (14). Install stop (15).
Illustration 6 g01034815
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
12. Install plunger (9) to spool (5).
13. Install spring (10). Install retainer (11).
4/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 14. Use Tooling (A) in order to install retaining ring (12).
15. Install slug (13).
16. Install spacers (8). Install spring (6), spring (7), and spool (4).
Illustration 7 g01034814
Illustration 8 g01096879
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install spool (5). Install piston (4).
Note: Hold each cover securely while you tighten the bolts.
5/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 18. Position cover (2). Install bolts (2A). Tighten bolts (2A) to a torque of 30 ± 4 N·m
(22 ± 3 lb ft).
19. Install cover (1). Install bolts (3). Tighten bolts (3) to a torque of 30 ± 4 N·m (22 ± 3 lb ft).
End By:
a. Install the transmission hydraulic control valve. Refer to Disassembly and Assembly,
"Transmission Hydraulic Control Valve - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:31:59 UTC+0800 2021
6/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i02304747
Transmission Hydraulic Control Valve - Install
SMCS - 3073-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 4 g00822714
4. Position transmission hydraulic control valve (6).
5. Install bolts (5). Tighten bolts (5) to a torque of 30 ± 4 N·m (22 ± 3 lb ft).
6. Install the gasket.
Illustration 5 g01096780
7. Reposition harness assembly (2), harness assembly (3), and harness assembly (4) when you
install cover (1).
8. Install cover (1).
9. Refill the transmission oil. Refer to Operation and Maintenance Manual, "Lubrication
Viscocities and Refill Capacities".
End By:
a. Install the hood. Refer to the engine supplement for the scraper Disassembly and Assembly,
"Hood - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:32:55 UTC+0800 2021
3/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i01659901
Drive Shaft - Remove
SMCS - 3253-011
Removal Procedure
1. Move the ejector forward.
Illustration 1 g00844512
2. Remove guard (1). Remove block (2) .
1/2(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g00844513
3. Remove eight bolts (3). The bolts must be discarded. Remove drive shaft (4). The drive
shaft weighs approximately 30 kg (65 lb). Use two people in order to remove the drive
shaft.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:33:51 UTC+0800 2021
2/2(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i01659905
Drive Shaft - Install
SMCS - 3253-012
Installation Procedure
Illustration 1 g00844513
1. Install drive shaft (4). The drive shaft weighs approximately 30 kg (65 lb). Use two people
in order to install the drive shaft. Install eight bolts (3). Bolts (3) must be replaced with new
bolts. The bolts must be torqued properly. For the proper torque, refer to Specifications,
"Drive Shaft" for the Scraper Power Train.
1/2(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g00844512
2. Install block (2). Install guard (1) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:34:48 UTC+0800 2021
2/2(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i01655983
Axle Shaft - Remove
SMCS - 3259-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Description Quantity
A 138-7575 Link Bracket 1
B 1P-7407 Eyebolt 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g00843570
1. Remove drain plug (1) in order to drain the final drive. The capacity of the final drive is
approximately 19 L (5 US gal).
Illustration 2 g00843571
2. Install Tool (A) to cover (2). Install a suitable lifting device to Tool (A). Remove the cover.
The cover weighs approximately 32 kg (70 lb).
Illustration 3 g00843572
2/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 3. Install Tool (B) to axle shaft (3). Partially remove the axle shaft.
Illustration 4 g00843573
4. Install a suitable lifting device to axle shaft (3). Remove the axle shaft. The right axle shaft
weighs approximately 41 kg (90 lb). The left axle shaft weighs approximately 68 kg (150
lb).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:35:43 UTC+0800 2021
3/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i01656019
Axle Shaft - Install
SMCS - 3259-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 138-7575 Link Bracket 1
B 1P-7407 Eyebolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 1 g00843573
1. Install a suitable lifting device to axle shaft (3). Partially install the axle shaft. The right axle
shaft weighs approximately 41 kg (90 lb). The left axle shaft weighs approximately 68 kg
(150 lb).
Illustration 2 g00843572
2. Install the axle shaft. Remove Tool (B) .
Illustration 3 g00843571
2/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 3. Install Tool (A) to cover (2). Install a suitable lifting device to Tool (A). Install the cover.
The cover weighs approximately 32 kg (70 lb).
4. Refill the final drive. Refer to Operation and Maintenance Manual, "Capacities (Refill)".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:36:39 UTC+0800 2021
3/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i01656077
Axle Shaft Guard - Remove and Install
SMCS - 7185-010
Removal Procedure
Start By:
A. Remove the left axle shaft. Refer to Disassembly and Assembly, "Axle Shaft - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the differential into a suitable container. The capacity of the differential is 12 L (3 US
gal).
1/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 1 g00845448
2. Disconnect the hose assembly (1). Disconnect the retainer (2). Slide the retainer toward the
differential and bevel gear.
Illustration 2 g00845557
3. Remove four bolts (3). Remove the guard.
4. Remove two O-ring seals from the tube assembly.
Installation Procedure
1. Install two O-ring seals to the tube assembly.
2/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 3 g00845557
2. Install the guard. Install four bolts (3) .
Illustration 4 g00845448
3. Slide the retainer toward the left axle housing. Connect the retainer (2). Connect the hose
assembly (1) .
4. Refill the differential. Refer to Operation and Maintenance Manual, "Capacities (Refil)".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:37:34 UTC+0800 2021
3/3(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER AWE
Configuration: 637G WHEEL SCRAPER-COAL BOWL AWE00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper Power Train
Media Number -RENR4074-01 Publication Date -01/04/2005 Date Updated -16/05/2005
i01590210
Power Pack - Remove
SMCS - 1000-011; 3030-011
Removal Procedure
Start By:
a. Remove the hood. Refer to the engine supplement for the scraper Disassembly and
Assembly, "Hood - Remove and Install".
b. Remove the hook. Refer to machine systems Disassembly and Assembly, "Hook - Remove
and Install".
Hot engine components can cause injury from burns. Before performing
maintenance on the engine, allow the engine and the components to cool.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire. To help prevent possible injury, turn the start switch off
when changing fuel filters or water separator elements. Clean up fuel
spills immediately.
1/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00824437
1. Disconnect battery cables (1) at the batteries.
2. Remove cover (2) and two brackets (3). Remove battery cables (1) from the battery box.
Illustration 2 g00824444
3. Disconnect three plugs (4).
2/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Illustration 3 g00830088
4. Disconnect two plugs (7). Remove wiring harness (6) from clip (5).
Illustration 4 g00830089
5. Disconnect two plugs (8). Remove clip (9).
Illustration 5 g00830091
6. Remove cover (10).
3/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
32. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
33. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
34. Illustration 6 g00830101
7. Disconnect plug (11) and pull the wiring harness through tube (12).
Illustration 7 g00824312
8. Turn fuel shutoff valve (13) to the OFF position.
Illustration 8 g00830112
9. Turn fuel shutoff valve (14) to the OFF position. Disconnect four hose assemblies (15).
4/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
35. Illustration 9 g00830121
10. Attach a suitable lifting device to lifting eye assembly (16).
Illustration 10 g00830209
11. Disconnect drive shaft (17) from the transfer gears.
Illustration 11 g00830117
12. Remove clip (18). Remove two bolts (19).
13. Repeat Step 12 at each corner of the power pack.
14. Remove the power pack. The weight of the power pack is approximately 3085 kg (6800 lb).
5/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
36. Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 25 00:38:30 UTC+0800 2021
6/6(W)
w
2021/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...