The document provides instructions for installing and removing a flywheel housing on a Caterpillar 434F backhoe loader engine. It describes:
- Using guide studs and a lifting device to position the flywheel housing on the engine block.
- Installing and tightening bolts to secure the housing.
- Removing bolts and lifting the housing off using the lifting device.
- Checking seals and dowels during removal and cleaning parts to prepare for installation.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...jfjkskekfsmem
This document provides instructions for installing a flywheel on a 434F backhoe loader with a C4.4 engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting alignment and installing related components like the electric starting motor.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufjsjekfksemm
This document provides instructions for installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes:
1) Cleaning and preparing the crankshaft, installing a new ring gear on the flywheel if needed, and lifting the flywheel into place using guide bolts before tightening the mounting bolts.
2) Checking the crankshaft rear seal for leaks, replacing if needed, and installing a new seal by aligning it with plastic sleeves and tightening mounting screws in the specified sequence.
3) Removing the flywheel housing by uninstalling mounting bolts and dowels, and lifting it away from the engine block using a hoist.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufdjjskefksmem
This document provides instructions for installing a flywheel on a 434F BACKHOE LOADER model powered by a C4.4 engine. The procedure involves installing a ring gear on the flywheel if it was removed, cleaning and preparing the crankshaft, lifting the flywheel into place using guide bolts, installing bolts and tightening them to the specified torque, and checking flywheel runout before reinstalling the electric starting motor.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts and lifting the flywheel housing off the engine cylinder block after removing the flywheel. Inspecting components and reversing steps
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and aligning the crankshaft flange before pressing the new crankshaft rear seal onto the flange using an alignment tool.
4. Removing bolts to lift the flywheel housing off the engine cylinder block using a lifting device. Inspection and installation steps are also
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...jfjkskekfsmem
This document provides instructions for installing a flywheel on a 434F backhoe loader with a C4.4 engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting alignment and installing related components like the electric starting motor.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufjsjekfksemm
This document provides instructions for installing a flywheel and flywheel housing on a Caterpillar C4.4 engine. It describes:
1) Cleaning and preparing the crankshaft, installing a new ring gear on the flywheel if needed, and lifting the flywheel into place using guide bolts before tightening the mounting bolts.
2) Checking the crankshaft rear seal for leaks, replacing if needed, and installing a new seal by aligning it with plastic sleeves and tightening mounting screws in the specified sequence.
3) Removing the flywheel housing by uninstalling mounting bolts and dowels, and lifting it away from the engine block using a hoist.
Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly0...ufdjjskefksmem
This document provides instructions for installing a flywheel on a 434F BACKHOE LOADER model powered by a C4.4 engine. The procedure involves installing a ring gear on the flywheel if it was removed, cleaning and preparing the crankshaft, lifting the flywheel into place using guide bolts, installing bolts and tightening them to the specified torque, and checking flywheel runout before reinstalling the electric starting motor.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful due to the flywheel's weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing the guide bolts and tightening the bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal. The seal is not serviceable and must be replaced.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation with guide bolts before tightening bolts to the specified torque.
4. Removing bolts and lifting the flywheel housing off the engine cylinder block after removing the flywheel. Inspecting components and reversing steps
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and aligning the crankshaft flange before pressing the new crankshaft rear seal onto the flange using an alignment tool.
4. Removing bolts to lift the flywheel housing off the engine cylinder block using a lifting device. Inspection and installation steps are also
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange, installing torx
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. It similarly describes removing the flywheel housing by taking out bolts and checking seals. Reinstallation involves cleaning, installing dowels or seals if needed, and torquing bolts with a lifting device and dial indicator used for alignment.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts and checking run out.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange without lubrication, installing torx
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation using guide bolts and lifting it into place before reinstalling bolts.
4. Removing bolts holding the flywheel housing in place and lifting it off the engine, then checking seals before reversing the process to
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange using a plastic sleeve
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix WTZ) Service Repair Manu...yin9niaojiao
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides notes on proper installation of springs, seals, and ensuring alignment of keys and notches. Tools required include a transmission repair stand, lifting eyes, bolts, drivers and pullers. Personal protective equipment is recommended when working with springs.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336E LH and 336E LNH Excavator (Prefix GNY) Service Repair Ma...yin9niaojiao
The document provides instructions for removing and installing a travel motor on an excavator. It is a 28-step procedure that includes draining oil, removing hoses and fittings, using lifting devices to remove the final drive and travel motor assembly, and reinstalling the components in reverse order. Precautions are provided for working with pressurized hydraulic systems and heavy components. The installation steps specify applying anti-seize compound to bolts and torquing them to the specified values.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are provided to prevent injury from spring forces and ensure proper alignment of parts.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FAJ) Service Re...yin9niaojiao
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix NAH) Service Repair ...yin9niaojiao
This document provides the disassembly and assembly procedures for a travel motor on a Cat 336D2 excavator model. It lists 30 steps for disassembly, removing components like caps, springs, valves, plugs and seals. It then lists 30 steps for assembly, installing components like seals, pistons, bearings, springs and covers in the reverse order of disassembly. The document provides illustrations and notes for each step to ensure correct reassembly.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FBT) Service Re...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...yin9niaojiao
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix MYG) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout to prevent injury from spring loaded parts.
More Related Content
Similar to Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment due to the flywheel's weight of approximately 155 pounds. For installing the flywheel, the instructions specify cleaning components, heating the ring gear, lifting the flywheel into place, and tightening bolts to the specified torque. Removing the crankshaft rear seal involves using a socket to remove screws, while installing requires aligning and pressing the new seal onto the crankshaft flange and torquing screws to the specified value.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange, installing torx
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by taking out bolts and using guide bolts and lifting equipment. It similarly describes removing the flywheel housing by taking out bolts and checking seals. Reinstallation involves cleaning, installing dowels or seals if needed, and torquing bolts with a lifting device and dial indicator used for alignment.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts and checking run out.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange without lubrication, installing torx
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it onto guide bolts, installing bolts finger tight, then removing guide bolts and tightening bolts while preventing rotation.
3) Removing the crankshaft rear seal by using a socket to remove screws, then removing the seal.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using a hammer and punch.
3. Cleaning and inspecting components, then positioning the flywheel for installation using guide bolts and lifting it into place before reinstalling bolts.
4. Removing bolts holding the flywheel housing in place and lifting it off the engine, then checking seals before reversing the process to
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416E backhoe loader. It describes:
1) Removing the flywheel by taking out bolts and using guide bolts and lifting equipment, being careful of the weight.
2) Installing the flywheel by positioning it with guide bolts and lifting equipment, replacing bolts, and tightening them in sequence.
3) Removing the crankshaft rear seal by taking out torx screws and discarding the seal and housing assembly.
4) Installing the new crankshaft rear seal by aligning it on the crankshaft flange using a plastic sleeve
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader. Key steps include:
1. Removing bolts to separate the flywheel from the engine and lifting it off using guide bolts and a lifting device.
2. Checking the flywheel and ring gear for wear before removal of the ring gear using punches.
3. Cleaning and positioning the flywheel for installation, adding bolts finger tight before final tightening.
4. Removing housing bolts and lifting the housing off the engine block using a lifting device. Inspection of seals is required before reinstallation.
Similar to Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instant Download.pdf (12)
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix WTZ) Service Repair Manu...yin9niaojiao
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides notes on proper installation of springs, seals, and ensuring alignment of keys and notches. Tools required include a transmission repair stand, lifting eyes, bolts, drivers and pullers. Personal protective equipment is recommended when working with springs.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336E LH and 336E LNH Excavator (Prefix GNY) Service Repair Ma...yin9niaojiao
The document provides instructions for removing and installing a travel motor on an excavator. It is a 28-step procedure that includes draining oil, removing hoses and fittings, using lifting devices to remove the final drive and travel motor assembly, and reinstalling the components in reverse order. Precautions are provided for working with pressurized hydraulic systems and heavy components. The installation steps specify applying anti-seize compound to bolts and torquing them to the specified values.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are provided to prevent injury from spring forces and ensure proper alignment of parts.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FAJ) Service Re...yin9niaojiao
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix NAH) Service Repair ...yin9niaojiao
This document provides the disassembly and assembly procedures for a travel motor on a Cat 336D2 excavator model. It lists 30 steps for disassembly, removing components like caps, springs, valves, plugs and seals. It then lists 30 steps for assembly, installing components like seals, pistons, bearings, springs and covers in the reverse order of disassembly. The document provides illustrations and notes for each step to ensure correct reassembly.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FBT) Service Re...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...yin9niaojiao
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix MYG) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout to prevent injury from spring loaded parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...yin9niaojiao
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components. Temperatures must be controlled for some parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...yin9niaojiao
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy components and ensuring proper hose, harness and bracket connections.
Caterpillar Cat 336D and 336D L Excavator (Prefix WRK) Service Repair Manual ...yin9niaojiao
The document provides instructions for removing and installing a final drive and travel motor on a Caterpillar 336D excavator. It lists required tools and gives step-by-step instructions involving disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix HER) Service Repair Manua...yin9niaojiao
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for removing and installing the rear gear group and related components on a 330D L excavator with a C9 engine. The removal process involves using tools to remove bolts, gears, bushings, bearings, and covers. The installation process gives specifics on cleaning parts, applying adhesives, inserting bearings at the proper angles and depths, and torquing bolts. Tolerances are provided for correct installation of several components.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual Instant D...yin9niaojiao
The document provides installation instructions for a swivel on an excavator. It describes removing the swivel by disconnecting hoses, removing bolts and lifting it out. It then details assembling the swivel by cleaning parts, installing seals and O-rings, positioning the housing over the rotor, and securing them with bolts. Finally, it describes installing the assembled swivel by connecting hoses and fittings and securing it with bolts.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...yin9niaojiao
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
The document provides instructions for disassembling the final drive of a 330D MH EXCAVATOR. It lists 31 steps to completely disassemble the final drive assembly including removing gears, carriers, shafts, seals and housings. Various tools are required including retaining ring pliers, link brackets, eyebolts and forcing bolts to separate the components. Cleanliness is important to prevent dirt from entering during disassembly.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i07030539
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(1/2 inch - 20 UNF by 4 inch)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01343963
Typical example
Always wear protective gloves when handling parts that have been
heated.
1. If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring
gear to the flywheel.
a. Identify the orientation of teeth (4) on the new ring gear (4).
Note: The chamfered side of the ring gear teeth must face toward the starting motor
when the flywheel is installed. The correct orientation of the chamfered will ensure
the correct engagement of the starting motor.
b. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F)
prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the
correct procedure.
2/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01245126
Typical example
3. Install a suitable lifting device to flywheel (1). The flywheel weighs approximately 71 kg
(155 lb).
4. Install Tooling (A) to positions (X) on the crankshaft.
5. Use the lifting device to position flywheel (1) onto Tooling (A).
6. Install bolts (2) to flywheel (1) finger tight.
7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1).
8. Remove the lifting device from flywheel (1).
9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of
140 N·m (103 lb ft).
10. Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting,
"Flywheel - Inspect" for further information.
End By:
a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
3/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763427
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Dispose of all fluids according to local regulations and mandates.
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The
assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced.
Illustration 1 g01269512
Typical example
1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2).
2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:01:38 UTC+0800 2019
2/2
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763428
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1
Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01258105
Illustration 2 g01255709
Typical example
1. Ensure that crankshaft flange (1) is clean, dry and free from damage.
2. Ensure that the face of the cylinder block and the bridge piece are clean and dry.
3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic
sleeve is squarely installed within crankshaft rear seal (2).
Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is
pushed over the crankshaft flange.
Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The
crankshaft rear seal must be installed dry.
2/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged
onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft
flange.
During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard
the plastic sleeve.
5. Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder
block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g01258357
Tightening sequence for the crankshaft rear seal
6. Install torx screws (4) finger tight.
Note: Do not install torx screws to positions (X) at this stage.
7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (16 lb ft). Tighten
torx screws (4) in the sequence that is shown in Illustration 3.
9. Remove Tooling (B).
10. Install remaining torx screws (4) to positions (X). Use Tooling (A) in order to tighten the
torx screws to a torque of 22 N·m (16 lb ft). Refer to Illustration 3.
3/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:02:34 UTC+0800 2019
4/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763429
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install a suitable lifting device to the flywheel housing in order to support the flywheel
housing. The flywheel housing weighs approximately 30 kg (66 lb).
1/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01244050
Typical example
2. Remove bolts (2) and bolts (3) from flywheel housing (1).
3. Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 2 g01244051
2/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Typical example
4. If the engine has an aluminum oil pan, remove dust seal (5).
5. If necessary, remove dowels (4) from the cylinder block.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
(M10 by 100 mm)
2
B 8T-5096 Dial Indicator Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the
flywheel housing.
Illustration 3 g01244056
Typical example
3/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer
to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder
block.
4. Install Tooling (A) to the cylinder block.
5. Install dust seal (5).
Illustration 4 g01244050
Typical example
6. Install a suitable lifting device to the flywheel housing. The flywheel housing weighs
approximately 30 kg (66 lb).
7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel
housing to the cylinder block.
8. Install bolts (2) and bolts (3) finger tight.
9. Remove Tooling (A). Install remaining bolts (3).
10. Tighten bolts (3) to a torque of 63 N·m (46 lb ft).
11. Tighten bolts (2) to a torque of 75 N·m (55 lb ft).
4/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 12. Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer
to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:03:30 UTC+0800 2019
5/5
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763430
Crankshaft Pulley - Remove and Install - Engines Without an
Automatic Belt Tensioner
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01255707
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1).
2. Remove thrust block (2).
3. Carefully remove crankshaft pulley (3) from the crankshaft.
Installation Procedure
Illustration 2 g01255707
1. Ensure that the crankshaft pulley and the thrust block are clean and free from damage.
Replace any components that are damaged. It is possible to reclaim a crankshaft pulley with
2/3
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly,
"Crankshaft Wear Sleeve (Front) - Remove and Install".
2. Ensure that the front of the crankshaft is clean and free from damage. Install crankshaft
pulley (3) to the crankshaft.
Illustration 3 g01390496
3. Align the holes in thrust block (2) with the holes in the crankshaft.
Note: Ensure chamfered holes (X) in thrust block (2). Face toward the front of the engine.
4. Install thrust block (2) to the assembly of the crankshaft pulley.
5. Install bolts (1) to thrust block (2).
6. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten the bolts evenly
to a torque of 115 N·m (85 lb ft).
7. Repeat Step 6 one more times in order to ensure correct torque.
End By:
a. Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 20 09:04:25 UTC+0800 2019
3/3
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434F BACKHOE LOADER FLY
Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763431
Crankshaft Pulley - Remove and Install - Engines With an
Automatic Belt Tensioner
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the Alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01249049
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1).
2. Remove thrust block (2).
3. Carefully remove the assembly of the crankshaft pulley from the crankshaft.
4. Follow Steps 4.a through 4.b in order to disassemble the crankshaft pulley.
a. Remove bolts (5).
b. Remove crankshaft pulley (4) from crankshaft adapter (3).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
22. 1. Ensure that the crankshaft adapter, the pulley and the thrust block are clean and free from
damage. Replace any components that are damaged. It is possible to reclaim a crankshaft
adapter with a worn seal surface by installing a wear sleeve. Refer to Disassembly and
Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install".
Illustration 2 g01367385
2. If necessary, follow Steps 2.a through 2.b in order to assemble the crankshaft pulley.
a. Install crankshaft pulley (4) to crankshaft adapter (3).
b. Install bolts (5) to the assembly of the crankshaft pulley, and the crankshaft adapter.
The bolts should be evenly spaced.
c. Tighten the bolts to a torque of 78 N·m (58 lb ft).
3. Ensure that the front of the crankshaft is clean and free from damage. Install the assembly of
the crankshaft pulley to the crankshaft.
3/4
434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/10/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...