Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp00001 00647)

Service Repair Manual
Models
424D Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 424D BACKHOE LOADER BGP
Configuration: 424D Backhoe Loader BGP00001-00647 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i01503434
Final Drive (Drive and Steering Axle)(Rear) - Install
SMCS - 4050-012-RE
Installation Procedure
Illustration 1 g00780205
1. Install bearing (15) onto the housing for the steering knuckle.
1/7424D Backhoe Loader BGP00001-00647 (MACHINE) POWERED BY 3054 Engine(...
2019/12/2https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2. Lubricate the seal in the bore of the hub. Install the hub onto the steering knuckle. Install the
outer hub bearing in order to secure the hub.
3. Install internal gear (13) .

4. Install slotted nut (12). Ensure that chamfered side of slotted nut (12) is facing outward.
5. Use tooling (A) in order to tighten slotted nut (12). Tighten the slotted nut to a rolling torque
of 46 N·m (34 lb ft).
Note: If the old bearings were reused, the rolling torque should be 27 N·m (20 lb ft).

6. After the proper rolling torque has been attained, install lock plate (11). Tighten bolts (10)
to a torque of 69 N·m (51 lb ft).
Note: Use new bolts in order to secure the lock plate.
7. Install washers (17) and (18). The flat face of washer (18) should be on the inside.
8. Install snap ring (19) .
9. Calculate the end play of the sun gear of the axle shaft.

a. Use a depth gauge and a straight edge in order to measure dimension (I). Dimension
(I) is the distance from the flange surface to the contact face of the thrust washer. An
example of dimension (I) is 166.2 mm (6.5 inch).
b. Straighten the axle and push the sun gear into the axle. Use a depth gauge and the
straight edge in order to determine dimension (II). Dimension (II) is the distance from
the end of the sun gear shaft to the flange surface of the hub. An example of
dimension (II) is 163.1 mm (6.4212 inch).
c. Subtract dimension (II) from dimension (I). Subtract the required end play from the
difference of dimensions (I) and (II). The remaining distance is the proper width of
the thrust washer that is located in the center of the planetary carrier. Ensure that the
proper thrust washer is installed in the planetary carrier. If necessary, change the
thrust washer. See Disassembly and Assembly, "Final Drive (Drive and Steering
Axle) (Rear) - Assemble".
Note: Refer to the Specifications Manual for the proper end play.

10. Use a suitable lifting device in order to install planetary carrier (5). It may be necessary to
move the planetary gears slightly in order to mesh the gears with the sun gear.
11. Install two socket head bolts (4). Tighten bolts (4) to a torque of 55 N·m (41 lb ft).

12. Install final drive drain plug (2). Tighten plug (2) to a torque of 120 N·m (89 lb ft).
13. Fill the final drives with the proper lubricants. See Operation and Maintenance Manual for
the proper lubricants and volumes.
End By:
a. Install the tie rods. See Disassembly and Assembly, "Tie Rods (Steering) (Rear) - Remove
and Install".
b. Install the rear axle. See Disassembly and Assembly, "Drive and Steering Axle (Rear) -
Install".
c. Install the tires and the wheels. See Disassembly and Assembly, "Tires & Wheels - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 23:34:34 UTC+0800 2019

Shutdown SIS
Previous Screen
Train
i01493531
Drive and Steering Axle Housing (Rear) - Remove
SMCS - 3020-011-RE; 3260-011-RE
Removal Procedure
Start By:
A. Remove the tires and wheels. See Disassembly and Assembly, "Tires & Wheels (Rear) -
Remove and Install".
B. Remove the rear axle. See Disassembly and Assembly, "Drive and Steering Axle (Rear) -
Remove".
1. Remove the cotter pin. Remove tie rod nut (1). Remove the ball joint end of the tie rod from
steering housing (2). See Disassembly and Assembly, "Tie Rod (Rear) - Remove and
Install".

2. Remove the drain plug for the differential housing. Drain the differential housing fluid into
a suitable container.
3. Use a suitable lifting device in order to support the axle housing. Support the axle housing
at the arrows.
4. Remove bolts (3) from the axle housing.

5. Use a suitable lifting device in order to remove the axle housing. Lift the axle housing at the
arrows.
Note: The weight of the axle housing is approximately 250 kg (550 lb).
Mon Dec 2 23:35:29 UTC+0800 2019

Shutdown SIS
Previous Screen
Train
i01505002
Drive and Steering Axle Housing (Rear) - Disassemble
SMCS - 3020-015-RE; 3260-015-RE
Disassembly Procedure
Start By:
A. Remove the tires and wheels. See Disassembly and Assembly, "Tires & Wheels (Rear) -
Remove and Install".
B. Remove the final drive. See Disassembly and Assembly, "Final Drive (Drive and Steering
Axle) (Rear) - Remove".
1. Remove the drain plug for the differential housing in order to drain the differential housing.
Drain the housing into a suitable container.
2. Remove snap ring (1). Remove thrust washers (2) and (3) .

Note: It may be necessary to push the axle into the housing slightly in order to remove the
snap ring and the washers. It may be necessary to pull the axle out of the housing slightly in
order to remove the snap ring and the washers.
3. Measure the distance (X). The distance (X) is the length between the bottom of adjustment
nut (4) and the top of bolt (5). Record this measurement for assembly purposes. Remove nut
(4) and bolt (5) .
4. Remove the ball joint end of the tie rod. See Disassembly and Assembly, "Tie Rods
(Steering) (Rear) - Remove and Install".
5. Remove four bolts (6). Remove two plastic caps (7) .

6. Use a suitable lifting device in order to support the housing for the steering knuckle. Use
forcing screws in order to push the bearing and pin (8) out of the housing.
7. Separate bearing (9) from pin (8). Remove the O-ring (10) .
Note: It is important to note the placement of the shims. Retain the proper shims with the
corresponding pins.

8. Remove the four bolts and the plastic caps from the bottom of the housing for the steering
knuckle. Use forcing screws in order to remove the pin from the bottom of the housing for
the steering knuckle. Separate bearing (11) from pin (12). Remove O-ring (13) .
Note: It is important to note the placement of the shims. Retain the proper shims with the
corresponding pins.
9. Use a suitable lifting device in order to remove the housing for the steering knuckle.
10. Remove seal (14) and bushing (15) from the bore of the housing for the steering knuckle.
Note: It may be necessary to destroy seal (14) in order to remove the seal.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

11. Remove bearing race (16) from the top of the axle housing.
12. Remove bearing race (17) from the bottom of the axle housing.

13. Use a suitable lifting device in order to remove axle shaft (18), sun gear (19), and both of
the universal joints from the axle housing.
14. Remove snap ring (20) from sun gear shaft (21) .
15. Remove seal (22) from the axle housing.

16. Remove bushing (23) from the axle housing.
17. Place alignment marks on the axle housing in order to ensure proper assembly. Use a
suitable lifting device in order to support the axle housing. Remove bolts (24). Remove the
axle housing.
Note: It may be necessary to pry the axle housing from the brake housing.

18. Place alignment marks on bushing (25). Remove bushing (25) .
Mon Dec 2 23:36:25 UTC+0800 2019

Shutdown SIS
Previous Screen
Train
i01505327
Drive and Steering Axle Housing (Rear) - Assemble
SMCS - 3020-016-RE; 3260-016-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 127-9310 Driver 1
B 127-9309 Driver 1
1. Use a suitable lifting device in order to install the axle housing onto the brake housing.
Install bolts (24) .

Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp00001 00647)

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

Similar to Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp00001 00647)

Similar to Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp00001 00647) (11)

More from fjsefkkefmmem

More from fjsefkkefmmem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp00001 00647)