This document provides instructions for installing an engine in a 420F2 backhoe loader. It describes 17 steps to complete the installation, which include attaching the engine using lifting equipment, installing mounting bolts and other components like the alternator, starter motor, and air conditioning compressor. The final steps include connecting fluids, turning on the battery, and filling coolant and oil. Tools required include a hydraulic jack and load leveling beam.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYC
Configuration: 420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416F2, 420F2 IT, 420F2 ST, 422F2, 428F2, 430F2 IT, 430F2 ST, 432F2, 434F2 and
444F2 Backhoe Loaders Engine Supplement
Media Number -UENR6152-01 Publication Date -01/06/2015 Date Updated -06/06/2018
i06199414
Engine - Install
SMCS - 1000-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
B 6V-3145 Load Leveling Beam 1
Illustration 1 g03849495
1. Attach Tooling (B) and a suitable lifting device to engine (30). The weight of engine (30) is
approximately 544kg (1200 lb). Use Tooling (B) and the suitable lifting device to position
engine (30) into the machine.
1/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g03849484
Illustration 3 g03849257
2. Align bell housing (28) to the engine and install bolts (29).
3. Rotate the engine and install bolts (26) in order to connect flywheel (27) to the torque
converter.
2/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g03849498
4. Install engine mounting bolts (31). Repeat on opposite side.
Illustration 5 g03849253
5. Install access panel (25).
Illustration 6 g02999824
6. Remove Tooling (A) from the transmission.
Illustration 7 g03849251
3/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g03849240
7. Connect ground strap (24). Connect harness assemblies (21) to the electric starting motor.
Connect clip (22) to bracket (23).
Illustration 9 g03849221
8. Connect harness assemblies (20) to the alternator.
Illustration 10 g03849219
9. Position air conditioner compressor (19) on the engine and install bolts (18).
4/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g03849206
10. Install fan and hub assembly (17). Install nuts (16).
Illustration 12 g03849203
11. Install fan shroud (15). Install fan guard (14). Install hose (13).
Illustration 13 g03849201
5/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 14 g03849199
12. Install tube (12). Install hoses (10) and (11).
13. Install tube (9). Install coolant tank (8).
Illustration 15 g03797235
14. Install fuel filter assembly (7).
Illustration 16 g03797205
15. Install plate assembly (5). Install bolts (4).
Note: Do not remove bolts (6).
6/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 17 g03797188
16. Position floor mat (3). Position plate (2) and install the bolts . Repeat on the opposite side of
the cab.
Illustration 18 g03797183
17. Turn battery disconnect switch (1) to the ON position.
18. Fill the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant
(ELC) - Change" for the correct filling procedure.
19. Fill the engine oil . Refer to Operation and Maintenance Manual, "Engine Oil and Filter -
Change" for the correct filling procedure.
End By:
a. Install air cleaner.
b. Install muffler.
c. Install hood assembly.
d. Install side panels.
Wed Nov 27 22:56:38 UTC+0800 2019
7/8420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYC
Configuration: 420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02289796
Fuel Priming Pump and Fuel Filter Base - Remove and
Install
SMCS - 1258-010; 1260-010; 1261-010-SE; 1262-010
Removal Procedure
Table 1
Required Tools(1)
Tool Part Number Part Description Qty
ZZ
9U-7069 Cap 3
9U-7067 Cap 3
(1)
SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE
REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE
EXPERIENCED SERVICEMAN.
Start By:
a. Remove the assembly of the filter case and the fuel filter element. Refer to this Disassembly
and Assembly Manual, "Fuel Filter Base - Remove and Install".
Note: Put identification marks on all fuel hose assemblies and on all tube assemblies for
installation purposes. After being disconnected, plug all fuel hose assemblies and plug all tube
assemblies. This helps prevent fluid loss, and this helps to keep contaminants from entering the
system.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00952432
Typical example
1. Disconnect the tube assembly (5). Disconnect the tube assembly (6). Install dust covers onto
the connectors for the fuel priming pump.
2. Disconnect the fuel return line from the connector (3). Install a dust cover to the connector
(3).
3. Disconnect the harness assembly from the connector (2).
4. Support the fuel priming pump. Remove the three setscrews (1) and discard the rubber
washers. Remove the fuel priming pump (4).
2/3420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00952432
Typical example
1. Clean the external surfaces of the fuel priming pump (4). Position the fuel priming pump (4)
and install the setscrews (1) and new rubber washers.
2. Remove the dust covers from the fuel priming pump. Remove the plugs from the tube
assemblies. Connect the tube assembly (5). Connect the tube assembly (6).
3. Connect the fuel return line to the connector (3).
4. Connect the harness assembly to the connector (2).
5. Remove the air from the fuel system. Refer to the Operations and Maintenance Manual,
"Fuel System - Prime".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 27 22:58:01 UTC+0800 2019
3/3420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYC
Configuration: 420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01924034
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ
9U-7067 Cap 4
9U-7069 Cap 4
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01001306
1. Remove bolts (1). Remove cover (2) from the cylinder head.
2/4420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01001381
2. Disconnect fuel injection lines (3) at fuel injection nozzles (4).
3. Disconnect fuel injection lines (3) at fuel injection pump (5).
4. Remove the fuel injection lines.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01001381
1. Connect fuel injection lines (3) at fuel injection nozzles (4). Tighten the nut to 30 N·m
(22 lb ft).
2. Connect the fuel injection lines at fuel injection pump (5). Tighten the nut to 30 N·m
(22 lb ft).
3. Remove the air from the fuel system. Refer to Operations and Maintenance Manual, "Fuel
System - Prime".
3/4420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g01001306
4. Position cover (2) on the cylinder head. Install bolts (1). Tighten the bolts to a torque of
9 N·m (80 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 27 22:58:56 UTC+0800 2019
4/4420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYC
Configuration: 420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01878115
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Illustration 1 g00975056
1. Remove hose (2) from fuel injection nozzle (1).
2. Remove bolt (3). Remove clamp (4) from the fuel injection nozzle.
3. Remove the fuel injection nozzle from the cylinder head. Remove O-ring seal (5) from the
fuel injection nozzle.
4. Remove seat washer (6) from the cylinder head.
Note: If the original seat washer is not removed, the projection of the fuel injection nozzle
will be incorrect when a new seat washer is installed.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 27 22:59:52 UTC+0800 2019
2/2420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYC
Configuration: 420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01878202
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00975210
1/2420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Lubricate seat washer (6) with clean engine oil. Install the seat washer in the cylinder head.
Note: If the original seat washer is reused, the projection of the fuel injection nozzle will be
incorrect.
2. Install O-ring seal (5) on fuel injection nozzle (1). Install the fuel injection nozzle in the
cylinder head.
Note: Alignment Pin (X) must be located opposite clamp (4).
3. Position clamp (4) on the fuel injection nozzle. Install bolt (3). Tighten the bolt to a torque
of 27 N·m (20 lb ft).
4. Install hose (2) to the fuel injection nozzle.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 27 23:00:48 UTC+0800 2019
2/2420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYC
Configuration: 420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02075261
Fuel Injection Pump - Remove - Delphi DP210
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
B 230-6283 Timing Pin ( Crankshaft) 1
C 9U-6198 Crankshaft Turning Tool 1
D 1P-2320 Combination Puller 1
ZZ
9U-7067 Cap 2
9U-7069 Cap 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
d. Remove the air compressor, if equipped. Refer to Disassembly and Assembly, "Air
Compressor - Remove and Install".
1/4420F2 IT Center Pivot Backhoe Loader LYC00001-UP (MACHINE) POWERED BY ...
2019/11/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...