This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 303 cr mini hydraulic excavator (prefix dma) service repair m...fjsjekdmmeme
This document provides assembly instructions for the main control valve of a 303 CR Mini Hydraulic Excavator. It describes assembling 8 different block assemblies (L through H) that make up the main control valve. The instructions note that cleanliness is important, valves must be assembled in the same configuration, and components must be returned to their original valves. Personal injury warnings are also provided regarding spring forces.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. Key steps include:
1. Using tooling to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Removing the valve keepers and spring retainer to access the valve spring.
3. Reversing the process to install new valve springs, making sure to complete installation on pairs of cylinders before moving to the next pair.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 303 cr mini hydraulic excavator (prefix dma) service repair m...fjsjekdmmeme
This document provides assembly instructions for the main control valve of a 303 CR Mini Hydraulic Excavator. It describes assembling 8 different block assemblies (L through H) that make up the main control valve. The instructions note that cleanliness is important, valves must be assembled in the same configuration, and components must be returned to their original valves. Personal injury warnings are also provided regarding spring forces.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
Caterpillar cat 320 d l excavator (prefix a9f) service repair manual (a9f0000...fjskekfseik
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The removal process involves using specialized tools to compress the valve springs so the valves can be serviced while keeping the piston at top dead center. Installation requires cleaning components, lubricating the valves, and using tools to carefully compress the springs into place. Proper assembly procedure and safety precautions are emphasized to avoid injury from released spring forces.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 304.5 mini hydraulic excavator (prefix anr) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a piston pump. It lists 34 steps for disassembling the pump, removing components like the piston, valve, plates, seals and bearings. It then lists 32 steps for assembling the pump, installing the components in reverse order and ensuring new seals and O-rings are used. Cleanliness is emphasized throughout to prevent contaminants from entering the system. Tools including snap ring pliers are required.
Caterpillar cat 304 d cr mini excavator (prefix tyk) service repair manual (t...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The 10-page document outlines the disassembly sequence and provides illustrations to remove each component. Technicians are instructed to inspect parts for wear and damage, measure component clearances, and replace worn parts.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
The document provides instructions for removing and installing various components of a M317D2 wheeled excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, applying sealant, and installing bolts and spacers.
- Removing the hydraulic oil filter by removing nuts and a cover to access the filter inside.
- Installing a new hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by disconnecting hoses and harnesses, draining fluid, and lifting the tank out after removing bolts.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fjskekfseik
This document provides instructions for removing the swing motor from a 304.5 Mini Hydraulic Excavator. The instructions include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to separate the right console to access the swing motor for removal. Proper containment of fluids and marking of disconnected lines and fittings is emphasized.
Caterpillar cat c2.2 industrial engine (prefix g7 m) service repair manual (g...ifkkdmdmdm
The document provides instructions for removing and installing the crankshaft pulley and front seal on an industrial engine. It describes removing the pulley by drilling holes in the seal, inserting a puller tool, and removing the woodruff key from the crankshaft. For installation, it instructs to clean components, insert the key, lubricate parts, and tighten the pulley nut to the specified torque. It also describes removing the front housing by removing mounting nuts and identifying locating features.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar Cat 329DL MOBILE HYD POWER UNIT Excavator (Prefix L5H) Service Re...shudun96087
This document provides instructions for removing and installing engine oil filter bases and oil coolers on a 329D L Mobile Hydraulic Power Unit. It describes using various tools to remove the filter base and disconnect hoses, then installing a new gasket and reconnecting hoses when reinstalling the filter base and oil cooler. Proper cleaning and torque specifications are noted to ensure correct assembly.
Caterpillar Cat 329DL MOBILE HYD POWER UNIT Excavator (Prefix L5H) Service Re...cnp692569
This document provides instructions for removing and installing engine oil filter bases and oil coolers on a 329D L Mobile Hydraulic Power Unit. It describes using various tools to remove the filter base and disconnect hoses, then installing a new gasket and reconnecting hoses when reinstalling the filter base and oil cooler. Disassembly instructions are also provided for removing bypass valves and seals from the filter base.
Caterpillar Cat 329DL MOBILE HYD POWER UNIT Excavator (Prefix L5H) Service Re...kesi7153062
This document provides instructions for removing and installing engine oil filter bases and oil coolers on a 329D L Mobile Hydraulic Power Unit. It describes using various tools to remove the filter base and disconnect hoses, then installing a new gasket and reconnecting hoses when reinstalling the filter base and oil cooler. Disassembly instructions are also provided for removing bypass valves and seals from the filter base.
Caterpillar cat 325 d l mobile hyd power unit (prefix h3n) service repair man...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using special tools to compress the valve springs, and removing components in the proper order - retainer locks, springs, washers and seals before removing the valves. Installation is the reverse process, lubricating and seating the valves before reinstalling the spring and retainer components. Safety precautions are outlined to avoid injury from the force of compressed springs.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...ifse9diodkdk
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
Caterpillar cat 320 d lrr excavator (prefix tae) service repair manual (tae00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D LRR excavator engine. It describes using special tools to compress the valve springs, rotate the crankshaft, and remove the springs and related components. The installation section gives steps for cleaning, lubricating, and reinstalling the springs and seals in the proper order. Removal and installation of valve guides is also outlined.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 304.5 mini hydraulic excavator (prefix anr) service repair ma...fjsjekdmmeme
The document provides instructions for disassembling and assembling a piston pump. It lists 34 steps for disassembling the pump, removing components like the piston, valve, plates, seals and bearings. It then lists 32 steps for assembling the pump, installing the components in reverse order and ensuring new seals and O-rings are used. Cleanliness is emphasized throughout to prevent contaminants from entering the system. Tools including snap ring pliers are required.
Caterpillar cat 304 d cr mini excavator (prefix tyk) service repair manual (t...fikskkdmmd1
This document provides instructions for disassembling and inspecting various engine components of a 304D CR Mini Excavator including the timing gear, camshaft, oil pan, piston, connecting rod, crankshaft, and cylinder block. The 10-page document outlines the disassembly sequence and provides illustrations to remove each component. Technicians are instructed to inspect parts for wear and damage, measure component clearances, and replace worn parts.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
The document provides instructions for removing and installing various components of a M317D2 wheeled excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, applying sealant, and installing bolts and spacers.
- Removing the hydraulic oil filter by removing nuts and a cover to access the filter inside.
- Installing a new hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by disconnecting hoses and harnesses, draining fluid, and lifting the tank out after removing bolts.
Caterpillar cat 304.5 mini hydraulic excavator (prefix wak) service repair ma...fjskekfseik
This document provides instructions for removing the swing motor from a 304.5 Mini Hydraulic Excavator. The instructions include releasing hydraulic system pressure, removing the cab and seat, disconnecting linkages from the left console, and removing bolts to separate the right console to access the swing motor for removal. Proper containment of fluids and marking of disconnected lines and fittings is emphasized.
Caterpillar cat c2.2 industrial engine (prefix g7 m) service repair manual (g...ifkkdmdmdm
The document provides instructions for removing and installing the crankshaft pulley and front seal on an industrial engine. It describes removing the pulley by drilling holes in the seal, inserting a puller tool, and removing the woodruff key from the crankshaft. For installation, it instructs to clean components, insert the key, lubricate parts, and tighten the pulley nut to the specified torque. It also describes removing the front housing by removing mounting nuts and identifying locating features.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar Cat 329DL MOBILE HYD POWER UNIT Excavator (Prefix L5H) Service Re...shudun96087
This document provides instructions for removing and installing engine oil filter bases and oil coolers on a 329D L Mobile Hydraulic Power Unit. It describes using various tools to remove the filter base and disconnect hoses, then installing a new gasket and reconnecting hoses when reinstalling the filter base and oil cooler. Proper cleaning and torque specifications are noted to ensure correct assembly.
Caterpillar Cat 329DL MOBILE HYD POWER UNIT Excavator (Prefix L5H) Service Re...cnp692569
This document provides instructions for removing and installing engine oil filter bases and oil coolers on a 329D L Mobile Hydraulic Power Unit. It describes using various tools to remove the filter base and disconnect hoses, then installing a new gasket and reconnecting hoses when reinstalling the filter base and oil cooler. Disassembly instructions are also provided for removing bypass valves and seals from the filter base.
Caterpillar Cat 329DL MOBILE HYD POWER UNIT Excavator (Prefix L5H) Service Re...kesi7153062
This document provides instructions for removing and installing engine oil filter bases and oil coolers on a 329D L Mobile Hydraulic Power Unit. It describes using various tools to remove the filter base and disconnect hoses, then installing a new gasket and reconnecting hoses when reinstalling the filter base and oil cooler. Disassembly instructions are also provided for removing bypass valves and seals from the filter base.
Caterpillar cat 325 d l mobile hyd power unit (prefix h3n) service repair man...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using special tools to compress the valve springs, and removing components in the proper order - retainer locks, springs, washers and seals before removing the valves. Installation is the reverse process, lubricating and seating the valves before reinstalling the spring and retainer components. Safety precautions are outlined to avoid injury from the force of compressed springs.
Caterpillar cat 325 d l mobile hyd power unit (prefix h3n) service repair man...fujsekfkksemm
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325D L Mobile Hydraulic Power Unit. It describes the necessary tools and safety precautions for each step. The procedures include using valve spring compressors to remove and install valves, driving tools to remove and install valve guides, and presses and installers to remove and install valve seat inserts.
Caterpillar Cat 325D L MOBILE HYD POWER UNIT (Prefix H3N) Service Repair Manu...f8usiejdkmdd
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using valve spring compressors to remove the valve retainers, springs and valves. New valves are lubricated and installed along with new seals, springs and retainers. Proper tools and safety precautions are emphasized to avoid injury from parts under spring force.
Caterpillar cat 325 d l mobile hyd power unit (prefix h3n) service repair man...kmf9ioseodk
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using specialty tools to compress the valve springs, and removing or installing the valve seals, springs, retainers and valves. Safety precautions are outlined to prevent injury from parts under spring force.
Caterpillar Cat 325D L MOBILE HYD POWER UNIT (Prefix H3N) Service Repair Manu...yan77xunhao
This service manual document provides instructions for removing and installing engine components such as valves, valve guides, valve seat inserts, the engine oil filter base, and oil cooler on a 325D L Mobile Hydraulic Power Unit powered by a C7 engine. The procedures describe draining fluids, using specialized tools to compress springs, and correctly installing seals and gaskets. Safety notices warn of potential injury from parts under spring force and ensure clean parts and fluids are used to prevent premature wear.
Caterpillar Cat 325D L MOBILE HYD POWER UNIT (Prefix H3N) Service Repair Manu...jfkskmmdmdm
This document provides instructions for removing and installing inlet and exhaust valves on a 325D L Mobile Hydraulic Power Unit. The procedure involves using valve spring compressors to remove the valve retainers, springs and valves. New valves are lubricated and installed along with new seals, springs and retainers. Proper tools and safety precautions are emphasized to avoid injury from parts under spring force.
Caterpillar Cat 325D L MOBILE HYD POWER UNIT (Prefix H3N) Service Repair Manu...jfkskmdmmdd
This service manual document provides instructions for removing and installing engine components on a 325D L Mobile Hydraulic Power Unit including:
- Removing and installing inlet and exhaust valves
- Removing and installing inlet and exhaust valve guides
- Removing and installing inlet and exhaust valve seat inserts
- Removing the engine oil filter base and oil cooler
- Disassembling the engine oil filter base
The document describes the required tools, removal and installation procedures, and safety notices for each component. Illustrations are provided to supplement the text instructions.
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...zatao0179249295
The document provides instructions for servicing components of a Caterpillar 336D2 L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...luanxianshi27
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
The document provides instructions for servicing components of a Caterpillar 336D2L excavator engine, including:
1. Procedures for removing and installing inlet and exhaust valve guides and valve seat inserts in the cylinder head. Various tools are required.
2. Guidelines for disassembling and assembling the engine oil filter base, which includes removing springs, valves, elbows and plugs.
3. Removal of the engine oil filter, filter base, and oil cooler, requiring disconnecting hoses and removing bolts.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper protrusion heights.
4) Extracting old seat inserts and pressing in new ones at a lowered temperature.
Caterpillar Cat 329DLN Excavator (Prefix SCY) Service Repair Manual (SCY00001...f8usiedkdmm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like valves, guides, and seats in a specific order.
2) Cleaning all parts to prevent damage and installing new components like valves, guides, and seats in the reverse order of removal using press tools.
3) Notes that proper assembly prevents injury and contaminants cause premature wear.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar C7 engine. It describes:
1) Using various tools to compress springs and remove components like retainers, springs, and valves.
2) Cleaning parts and lubricating valves before installation.
3) Tapping guides into place using drivers and ensuring proper heights above the cylinder head.
4) Extracting old seat inserts and pressing new ones in at the proper depths.
Similar to Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service repair manual (l5h00001 and up) (20)
Caterpillar cat 725 c articulated truck (prefix lfb) service repair manual (l...ifse9diodkdk
This document provides instructions for disassembling and assembling the torque converter in a 725C articulated truck. It describes 43 steps to disassemble the various components of the torque converter including removing bolts, seals, bearings, races, and housing pieces. It then lists the required tools and provides a brief assembly procedure, noting to clean all surfaces and apply locking compound or O-ring assembly compound as needed.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...ifse9diodkdk
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...ifse9diodkdk
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j9d) service r...ifse9diodkdk
This document provides the disassembly and assembly procedures for a travel motor on a 329DL Mobile Hydraulic Power Unit excavator. The disassembly procedure outlines 28 steps to dismantle the various components of the travel motor. The assembly procedure describes 19 steps to reassemble the travel motor components in reverse order. Proper cleaning and installation of new seals and gaskets is emphasized throughout.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, screws, and lifting devices to separate individual parts which are then cleaned and inspected.
4. Disassembling internal components of the carrier assembly like planetary gears and shafts.
The instructions describe each step in detail and include illustrations of the components and proper tooling to use. Safety notes are included about handling
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, adapters, seals and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process is reversed to install the RPTO following similar steps and precautions.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning and inspecting the crankshaft and installing new bearings, thrust washers and seals before reinstalling the crankshaft and torquing the bolts to the specified values. Clear illustrations supplement the text instructions.
Caterpillar cat 329 d2 l excavator (prefix tmj) service repair manual (tmj000...ifse9diodkdk
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, bolts and brackets holding the pump. It also details checking clearances after installation and installing the oil pan. Installation involves cleaning components, installing dowels and bolts, and checking gear backlash.
This document provides instructions for installing an engine oil pump on a C7.1 engine. It describes cleaning and inspecting the oil pump components and installing the cross over tube assembly with new gaskets. It also details reassembling the oil pump if disassembled, ensuring proper dowel pin locations, and installing the oil pump assembly onto the cylinder block and torquing the bolts. The installation is completed by installing a new gasket and the suction pipe.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. Precautions are given to keep parts clean and ensure correct alignment of sleeves and oil holes. Required tools include a driver group. The process concludes by removing the flywheel after the RPTO is disassembled.
Caterpillar cat 329 d ln excavator (prefix ebm) service repair manual (ebm000...ifse9diodkdk
The document provides instructions for removing and installing pistons and connecting rods on a Caterpillar C7 engine. It describes removing the cylinder head, oil pump, and piston cooling jets before removing each piston and connecting rod assembly. The connecting rod cap and bearings are removed, then the piston and connecting rod are separated. Reinstallation follows the reverse order, applying anti-seize compound and using tools to properly position the piston rings and install the connecting rod bearings.
Caterpillar cat 329 d l excavator (prefix yfw) service repair manual (yfw0000...ifse9diodkdk
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, carriers and seals. It then lists 21 steps for assembly, providing details on cleaning parts, applying lubricants, setting bearing preloads using presses and shims, and installing seals and gears back into their original locations and orientations. Cleanliness is emphasized as important throughout the process.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...ifse9diodkdk
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and replacing bolts to hold the jets in place.
- Procedures for removing pistons and connecting rods by identifying parts, removing caps and bolts, and pushing components out of the engine block.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...ifse9diodkdk
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 320 n track type excavator (prefix 2dl) service repair manual...ifse9diodkdk
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...ifse9diodkdk
This document provides instructions for removing and installing valve stem seals on Caterpillar 320, 320L, and 320N track-type excavators. The procedure involves using a seal pick tool to remove the old seals from the valve guides and install new seals. Technicians are instructed to keep all parts clean and coat the new seals with engine oil during installation.
This document provides instructions for separating a track on a 320D LN excavator. It lists the required tools which include a chain, track block assembly, electric hydraulic pump group, hydraulic pressure gauge, pipe bushings, quick connect couplers, plugs, hoses, track press tool group, double acting cylinder, and track press rollover group. The procedure involves cleaning the exterior of the track thoroughly before disassembly to prevent dirt from entering the internal mechanism when the track is separated.
This document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 320D L excavator engine. The key steps are:
1. Use special tools to compress the valve spring and rotate the crankshaft to allow the piston to hold the valve open while the spring is removed.
2. Remove the valve keepers and spring retainer to access the valve spring.
3. Installation is the reverse of removal, ensuring parts are clean and lubricated before reassembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i06201017
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01124395
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (B) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
C 1U-7792 Guide Collar 1
D 149-4008 Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01124397
Note: Position the valve guides and tap on the top of the valve guides in order to start the
valve guides into the cylinder head assembly.
1. Use Tooling (A) and Tooling (C) to install inlet valve guides (1) . Install inlet valve guides
(1) until the protrusion is 23.0 ± 0.50 mm (0.90 ± 0.020 inch) above the cylinder head
assembly.
2. Use Tooling (B) and Tooling (D) to install the exhaust valve guides. Install the exhaust
valve guides until the protrusion is 24.05 ± 0.5 mm (1.0 ± 0.02 inch) above the cylinder
head assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:24:44 UTC+0800 2020
3/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02954230
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor(2)
1
165-5647 Valve Seat Extractor(3)
1
6V-4804 Handle 1
6V-4192 Shaft 1
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool Group
(2)
Use for removal of the exhaust valve seats
(3)
Use for removal of the inlet valve seats
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01124436
1. Use Tooling (A) to remove valve seat inserts (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
149-6115 Installer 1
133-9306 Valve Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01475612
1. Lower the temperature of new valve seat inserts (1).
2. Use Tooling (B) and a suitable press to install the new valve seat inserts in the cylinder
head.
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:25:40 UTC+0800 2020
3/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301129
Engine Oil Filter Base and Oil Cooler - Remove
SMCS - 1306-011; 1378-012
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Remote Mounted Engine Oil Filter Base
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Illustration 1 g01152338
1. Use Tooling (A) to remove engine oil filter (1) .
2. Remove bolts (2) and engine oil filter base (3) .
Engine Mounted Engine Oil Filter Base
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
2/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01152340
2. Disconnect hose assemblies (4) .
3. Disconnect hose assembly (5) .
4. Remove bolts (6) and engine oil filter base (7) .
5. Remove oil cooler (8) and the gasket from the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:26:36 UTC+0800 2020
3/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301168
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
A. Remove the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Remote Mounted Engine Oil Filter Base
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01152353
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove oil filter bypass valve (2) from engine oil filter base (1) .
Engine Mounted Engine Oil Filter Base
2/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g01152356
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove adapter (3) and the O-ring seals from engine oil filter base (4) .
2. Remove oil filter bypass valve (5) and oil filter bypass valve (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:27:32 UTC+0800 2020
3/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301184
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engine Mounted Engine Oil Filter Base
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound 1
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01152356
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (6) and oil filter bypass valve (5) in engine oil filter base (4) .
2. Apply Tooling (A) to the threads of adapter (3). Install the O-ring seals and adapter (3).
Tighten adapter (3) to a torque of 150 ± 20 N·m (110 ± 15 lb ft).
Remote Mounted Engine Oil Filter Base
2/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01152353
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (2) in engine oil filter base (1) .
End By: Install the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:28:28 UTC+0800 2020
3/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301151
Engine Oil Filter Base and Oil Cooler - Install
SMCS - 1306-012; 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engine Mounted Engine Oil Filter Base
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01152340
1. Position the gasket and oil cooler (8) on the engine.
2. Install engine oil filter base (7) and bolts (6) .
3. Connect hose assembly (5) .
4. Connect hose assemblies (4) .
5. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
Remote Mounted Engine Oil Filter Base
2/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01152338
1. Position engine oil filter base (3) and install bolts (2) .
2. Install engine oil filter (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:29:23 UTC+0800 2020
3/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301238
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01152440
1. Remove bracket (5) .
2. Remove pickup tube (4) and the gasket from engine oil pump (1) .
3. Remove outlet elbow (3) and the O-ring seals from engine oil pump (1) .
4. Remove bolts (2) and engine oil pump (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:30:19 UTC+0800 2020
2/2
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301249
Engine Oil Pump - Disassemble
SMCS - 1304-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8B-7554 Bearing Cup Puller Gp 1
B 1P-0510 Driver Gp 1
Start By:
A. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g01152456
1. Remove bolt (1) .
2. Remove idler gear (3) from shaft (4) .
3. Use Tooling (B) and remove bearing (2) from idler gear (3) .
4. Use Tooling (A) to remove drive gear (5) from engine oil pump (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:31:15 UTC+0800 2020
2/2
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301303
Engine Oil Pump - Assemble
SMCS - 1304-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01152456
1. Use Tooling (B) and a suitable press to install drive gear (5) on engine oil pump (6) until
drive gear (5) is flush with the end of the shaft assembly.
2. Install bearing (2) in idler gear (3). Install bearing (2) so the distance between the hub bolt
face of idler gear and bearing (2) is 0.75 ± 0.25 mm (0.030 ± 0.010 inch).
3. Install idler gear (3) on shaft (4). Install bolt (1). Tighten bolt (1) to a torque of 70 ± 15 N·m
(52 ± 11 lb ft).
End By: Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:32:11 UTC+0800 2020
2/2
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...