This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the spot welds securing the seal retainer.
2. Remove the retainer, crankshaft front seal, and gasket from the front cover.
3. Inspect the front cover dowels and replace if needed before installing the new seal.
1) The document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar 3054 engine.
2) The removal procedures describe removing mounting bolts, seals, gaskets and housings. The installation procedures describe cleaning surfaces, installing seals, gaskets and housings, and tightening bolts to the specified torques.
3) Tools, torque specifications, and cautions about cleanliness and fluid containment are provided to correctly complete the repair procedures.
This document provides instructions for removing and installing a flywheel housing on a 3054 engine. It includes the following steps:
1. Remove the electric starting motor and flywheel. Support the engine and remove mounting bolts from the top and bottom of the housing. Lift the housing off using link brackets.
2. Clean the mating surfaces and install new seals if needed. Position the housing using link brackets and install mounting bolts.
3. Tighten the bolts to the specified torque depending on whether the housing is aluminum or cast iron. Reinstall the flywheel and electric starting motor.
1) The document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar 3054 engine.
2) The removal procedures describe removing mounting bolts, seals, gaskets and housings. The installation procedures describe cleaning surfaces, installing seals, gaskets and housings, and tightening bolts to the specified torques.
3) Tools, torque specifications, and cautions about cleanliness and fluid containment are provided to correctly complete the repair procedures.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fjjkekfksemmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts, attaching lifting tools, and separating the housing from the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening mounting bolts with specified torques. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fujsjfkkskemme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine block. For installation, it describes cleaning mating surfaces, attaching lifting tools to the housing, and reversing the removal steps to lower the housing back onto the engine block dowels. Torque specifications are provided for reinstalling mounting bolts.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fusjejedrfjskekem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts and washers, lifting the flywheel off, and installing in reverse order. For the crankshaft rear seal, it differentiates between engines using a 14 bolt or 10 bolt housing assembly and outlines cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using link brackets and a lifting device to remove the housing by removing mounting bolts at the top and on the cylinder block. Cleaning surfaces and checking seals and dowels is also described for installation. Tools, safety notices, and step-by-step procedures with illustrations are provided for both removal and installation of the flywheel housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
1) The document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar 3054 engine.
2) The removal procedures describe removing mounting bolts, seals, gaskets and housings. The installation procedures describe cleaning surfaces, installing seals, gaskets and housings, and tightening bolts to the specified torques.
3) Tools, torque specifications, and cautions about cleanliness and fluid containment are provided to correctly complete the repair procedures.
This document provides instructions for removing and installing a flywheel housing on a 3054 engine. It includes the following steps:
1. Remove the electric starting motor and flywheel. Support the engine and remove mounting bolts from the top and bottom of the housing. Lift the housing off using link brackets.
2. Clean the mating surfaces and install new seals if needed. Position the housing using link brackets and install mounting bolts.
3. Tighten the bolts to the specified torque depending on whether the housing is aluminum or cast iron. Reinstall the flywheel and electric starting motor.
1) The document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar 3054 engine.
2) The removal procedures describe removing mounting bolts, seals, gaskets and housings. The installation procedures describe cleaning surfaces, installing seals, gaskets and housings, and tightening bolts to the specified torques.
3) Tools, torque specifications, and cautions about cleanliness and fluid containment are provided to correctly complete the repair procedures.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fjjkekfksemmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts, attaching lifting tools, and separating the housing from the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening mounting bolts with specified torques. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fujsjfkkskemme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine block. For installation, it describes cleaning mating surfaces, attaching lifting tools to the housing, and reversing the removal steps to lower the housing back onto the engine block dowels. Torque specifications are provided for reinstalling mounting bolts.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fusjejedrfjskekem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts and washers, lifting the flywheel off, and installing in reverse order. For the crankshaft rear seal, it differentiates between engines using a 14 bolt or 10 bolt housing assembly and outlines cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using link brackets and a lifting device to remove the housing by removing mounting bolts at the top and on the cylinder block. Cleaning surfaces and checking seals and dowels is also described for installation. Tools, safety notices, and step-by-step procedures with illustrations are provided for both removal and installation of the flywheel housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, it details removing bolts and lifting the flywheel off. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and removing or installing the seal and housing. Precautions are provided regarding cleanliness and proper torque specifications.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step procedures. For flywheel removal, a lifting device and link bracket must be used to detach the flywheel from the crankshaft. For rear seal removal, either a 14-bolt or 10-bolt housing assembly is removed to access the seal. Installation requires aligning and securing the components in the reverse order of disassembly. Proper cleaning, lubrication and torque specifications are noted.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using link brackets and a lifting device to remove the housing by removing mounting bolts at the top and on the cylinder block. It also details cleaning surfaces, inspecting seals and dowels, and attaching the housing back in place after cleaning. Proper cleaning, inspection, and torque specifications are emphasized to complete the procedure.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step procedures. For flywheel removal, a lifting device and link bracket must be used to detach the flywheel from the crankshaft. For rear seal removal, either a 14-bolt or 10-bolt housing assembly is removed to access the seal. Installation requires aligning and securing the components in the reverse order of disassembly. Precautions like cleaning parts and applying lubrication are noted.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
More Related Content
Similar to Caterpillar Cat 416B Backhoe Loader (Prefix 8SG) Service Repair Manual Instant Download (8SG12000).pdf
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, it details removing bolts and lifting the flywheel off. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and removing or installing the seal and housing. Precautions are provided regarding cleanliness and proper torque specifications.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step procedures. For flywheel removal, a lifting device and link bracket must be used to detach the flywheel from the crankshaft. For rear seal removal, either a 14-bolt or 10-bolt housing assembly is removed to access the seal. Installation requires aligning and securing the components in the reverse order of disassembly. Proper cleaning, lubrication and torque specifications are noted.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using link brackets and a lifting device to remove the housing by removing mounting bolts at the top and on the cylinder block. It also details cleaning surfaces, inspecting seals and dowels, and attaching the housing back in place after cleaning. Proper cleaning, inspection, and torque specifications are emphasized to complete the procedure.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step procedures. For flywheel removal, a lifting device and link bracket must be used to detach the flywheel from the crankshaft. For rear seal removal, either a 14-bolt or 10-bolt housing assembly is removed to access the seal. Installation requires aligning and securing the components in the reverse order of disassembly. Precautions like cleaning parts and applying lubrication are noted.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
Similar to Caterpillar Cat 416B Backhoe Loader (Prefix 8SG) Service Repair Manual Instant Download (8SG12000).pdf (13)
This document provides instructions for removing and installing the transmission transfer gears on a Caterpillar 651E wheel tractor. The process involves removing 18 components from the transfer gears including gears, couplings, bearings, seals and bolts. Reinstallation is the reverse of the removal process and includes checking bearing end play and installing new seals. Proper heating and pressing of bearings is required during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes using various tools to support the camshaft and guide it out of and back into the cylinder head. Precautions are listed to keep the camshaft level and aligned during removal and installation to avoid damage. Lubrication of parts and use of thread lock compound are also specified in the multi-step procedures.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies heating the new seal before pressing it into the flywheel housing with a driver plate until it is fully seated. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...shibi1322
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...shibi1322
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing several other components first, including the camshaft gear and rocker arms. Tools are then used to support the camshaft as it is moved out of the cylinder head and into a guide tool to prevent damage to the camshaft bearings during removal.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
This document provides instructions for removing and installing various components of a Caterpillar 3306 engine, including:
1. Removing and installing the spacer plate, water directors, lifter group, camshaft, and camshaft bearings.
2. Detailed procedures are given for each component, including required tools and special notes about cleaning, lubrication, and ensuring proper timing.
3. The document is part of a service repair manual for a Caterpillar 639D wheel scraper model powered by a 3306 engine.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including housing assemblies, clutch pistons, friction disks, bearings, gears, and seals. It then describes assembling the torque converter in 25 steps by reversing the removal process and provides torque specifications for fasteners. The goal is to separate, remove, and reassemble each component of the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying locking adhesive and heating components as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift heavy components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals using various specialty tools.
This document provides disassembly instructions for the transmission planetary system of a 637G Wheel Tractor. It outlines 50 steps to fully disassemble the transmission, including removing clutch housings, carrier assemblies, shafts, gears, plates, rings, seals and other components. Special care must be taken when removing components under spring pressure. Various tools are required to properly support, secure and remove parts from the transmission.
This document provides instructions for disassembling a torque converter in a 637G wheel tractor. It lists 32 steps to remove various components of the torque converter including carriers, gears, shafts, seals, and housings. Tools required are also listed, such as retaining ring pliers, driver groups, pullers, and link brackets. Care must be taken to contain fluids and protect parts from contamination.
This document provides assembly instructions for a torque converter in a 637G wheel tractor-scraper. It details 31 steps to assemble the torque converter, including installing seals, gears, shafts, bearings and housings in the proper order and with specified torques. It also provides disassembly instructions for the transfer gears in 18 steps, removing components like seals, bolts, cages and shafts. Tools required include drivers, pullers, link brackets and dial indicators.
This document provides assembly instructions for a torque converter in a 637G wheel tractor. It outlines 33 steps to assemble the various components of the torque converter like bearings, seals, gears, and housing. Proper cleaning and torque specifications are noted. Additionally, the document describes disassembly and assembly procedures for transfer gears in the wheel tractor, including removing 18 components like bolts, seals, and bearings. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
This document provides instructions for removing and installing a cylinder head, lifter group, and camshaft on a Caterpillar 3408E or 3412E engine. The removal process involves detaching various components and hoses from the cylinder head and loosening bolts. Special tools are required to safely lift and handle parts due to their heavy weight. The installation follows the reverse order and specifies applying sealant and oil to parts and tightening bolts in a sequence with a torque wrench. Precautions are given to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the transmission of a 637E wheel tractor. It lists 47 steps to disassemble the transmission and 21 steps to reassemble it. Some key parts that are disassembled include the housing assembly, planetary group, carrier assemblies, gears, discs, plates, pistons, shafts, seals, springs, snap rings, and bearings. The instructions provide details on removing and installing each part using various tools. Weights of the major components are provided to aid in removal and installation.
This document provides instructions for disassembling and assembling the torque converter of a 627H Wheel Tractor. It describes 18 steps to disassemble the torque converter by removing various parts like retaining rings, bolts, seals, bearings, and assemblies. It then describes 24 steps to reassemble the torque converter by installing these same parts in the reverse order. The document includes illustrations and lists any required tools for each step.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing gears, bearing cages, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including pressing bearings onto gears, installing cups and cages, adjusting shims to achieve proper end play, and torquing bolts. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. It outlines 18 steps to disassemble the transfer gear case by removing bearing cages, gears, shims, and cups. It then describes 20 steps to reassemble the transfer gear case, including cleaning parts, pressing bearings onto gears, adjusting shim thickness to achieve proper end play, and torquing bolts to the specified values. Tools required are also listed.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416B BACKHOE LOADER 8SG
Configuration: 416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 4 23:42:55 UTC+0800 2019
3/3
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416B BACKHOE LOADER 8SG
Configuration: 416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 4 23:43:52 UTC+0800 2019
4/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416B BACKHOE LOADER 8SG
Configuration: 416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 4 23:44:49 UTC+0800 2019
4/4
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416B BACKHOE LOADER 8SG
Configuration: 416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 4 23:45:45 UTC+0800 2019
2/2
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416B BACKHOE LOADER 8SG
Configuration: 416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742537
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00541748
Typical example
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Place Tooling (B) in the holes in order to remove crankshaft front seal (1). Use Tooling (B)
in each of the three holes to evenly remove the crankshaft front seal.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Dec 4 23:46:42 UTC+0800 2019
2/2
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416B BACKHOE LOADER 8SG
Configuration: 416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742545
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the housing for the crankshaft front seal and inspect the housing for damage.
2. Lubricate the lip of the crankshaft front seal with clean engine oil.
1/3
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
19. Illustration 1 g00541748
3. Place crankshaft front oil seal (1) into the housing.
NOTICE
Ensure that the lip of the crankshaft front seal that is spring loaded is
facing toward the inside of the front housing and that it is square with
the bore of the housing for the crankshaft front seal.
Illustration 2 g00622033
4. Use Tooling (A) to install crankshaft front oil seal (1).
5. Apply clean engine oil on the area of the crankshaft pulley that will be in contact with
crankshaft front seal (1).
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Wed Dec 4 23:47:39 UTC+0800 2019
2/3
416B Backhoe Loader 8SG12000-14798 (MACHINE) POWERED BY 3054 Engine(S...
2019/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...