This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using specialized tools to compress the valve springs, remove the valve keepers and other components, and extract the valves from the cylinder head. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using tools to compress springs and insert new components in the reverse order of removal. Safety precautions are provided regarding working with compressed springs. A separate section then details removing and installing the engine oil filter base.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ufusjfjkkekm
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F backhoe loader. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning and inspecting the oil cooler, installing a new gasket, and securing the cooler in place with bolts and spacers. Tools required include wrenches and containers for draining fluids. Safety precautions are provided to contain fluids and follow cleanliness standards when working on engine components.
Caterpillar cat 320 e l excavator (prefix tnj) service repair manual (tnj0000...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E L excavator engine. The removal process involves using specialized tools to compress the valve springs and remove the keepers and springs. Installation is the reverse of removal, requiring cleaning, lubricating, and using tools to compress springs during reassembly. Proper torque values are specified for reinstalling components.
Caterpillar cat 320 e excavator (prefix aws) service repair manual (aws00001 ...fhhjsjekmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E excavator engine. The summary is:
1. The procedure describes removing the cylinder head and using a valve spring compressor tool to compress the valves springs, remove the keepers, and take out the valves.
2. Reinstallation involves cleaning components, lubricating the valve stems, and using the compressor tool to insert the valves back into the cylinder head and replace the springs and keepers.
3. Proper torque values are provided for reinstalling the cylinder head.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fhhjsjekmdme
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using a valve spring compressor tool to compress the valve springs, allowing removal of the valve keepers and springs. Identification marks should be made on the valves and springs. Removal and installation is reversed, with inspection of components and lubrication of valve stems before reinstallation. Safety precautions are noted regarding the force of compressed springs. A similar process is described for removing and installing the engine oil filter base.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D2 L excavator engine. It describes using a valve spring compressor tool to compress the valve springs before removing the valve keepers and other components. When installing new valves, the instructions specify cleaning and lubricating components, compressing springs with the tool to install keepers, and checking valve depths once installation is complete. Removal and installation of valve guides requires special machinery and trained personnel and includes reaming guides and cutting valve seats after installation.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed, springs and retainers are compressed with the tool and keepers are fitted. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ufusjfjkkekm
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar 416F backhoe loader. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning and inspecting the oil cooler, installing a new gasket, and securing the cooler in place with bolts and spacers. Tools required include wrenches and containers for draining fluids. Safety precautions are provided to contain fluids and follow cleanliness standards when working on engine components.
Caterpillar cat 320 e l excavator (prefix tnj) service repair manual (tnj0000...ufjjsjekkeemme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E L excavator engine. The removal process involves using specialized tools to compress the valve springs and remove the keepers and springs. Installation is the reverse of removal, requiring cleaning, lubricating, and using tools to compress springs during reassembly. Proper torque values are specified for reinstalling components.
Caterpillar cat 320 e excavator (prefix aws) service repair manual (aws00001 ...fhhjsjekmdme
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320E excavator engine. The summary is:
1. The procedure describes removing the cylinder head and using a valve spring compressor tool to compress the valves springs, remove the keepers, and take out the valves.
2. Reinstallation involves cleaning components, lubricating the valve stems, and using the compressor tool to insert the valves back into the cylinder head and replace the springs and keepers.
3. Proper torque values are provided for reinstalling the cylinder head.
Caterpillar cat 320 e excavator (prefix shx) service repair manual (shx00001 ...fhhjsjekmdme
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C6.6 engine. The procedure involves using a valve spring compressor tool to compress the valve springs, allowing removal of the valve keepers and springs. Identification marks should be made on the valves and springs. Removal and installation is reversed, with inspection of components and lubrication of valve stems before reinstallation. Safety precautions are noted regarding the force of compressed springs. A similar process is described for removing and installing the engine oil filter base.
Caterpillar cat 303.5 e2 mini hydraulic excavator (prefix jwy) service repair...fjsjekdmmeme
The document provides instructions for removing and installing inlet and exhaust valves, valve springs, valve guides, and valve seat inserts on a Caterpillar 303.5E2 Mini Hydraulic Excavator engine. The procedures describe using various tools to compress valve springs, remove components in the proper sequence while keeping them clean, and reinstalling components in the reverse order of removal. Special tools and trained personnel are required for some tasks like removing valve guides and seats.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 320D2 L excavator engine. It describes using a valve spring compressor tool to compress the valve springs before removing the valve keepers and other components. When installing new valves, the instructions specify cleaning and lubricating components, compressing springs with the tool to install keepers, and checking valve depths once installation is complete. Removal and installation of valve guides requires special machinery and trained personnel and includes reaming guides and cutting valve seats after installation.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove the keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, and the springs and keepers are compressed into place using the tool. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The procedure involves using specialized tools to compress the valve springs to remove and install valve keepers. Safety precautions are outlined to prevent injury from the force of compressed springs. Instructions are also given for removing and installing the engine oil filter base, which involves draining oil and replacing gaskets.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, springs and retainers are compressed using the tool and keepers are installed. The engine oil filter base and engine oil cooler are also removed and installed, following cleaning and installation of new gaskets.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...fjjskekfkskemf
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 416F backhoe loader. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. The installation procedure specifies cleaning components, lubricating valve stems, compressing springs with the tool to insert keepers, and installing the valves in the proper positions. A separate section also outlines removing and installing the engine oil filter base.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ifksjejdkemm
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 416F backhoe loader. The removal procedure involves using a valve spring compressor tool to compress the springs, remove the keepers, and take out the valves. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using the compressor tool to reinstall the valves and springs. Proper tools and safety precautions are highlighted. A second section details removing and installing the engine oil filter base, including draining oil and replacing gaskets.
Caterpillar cat 314 e lcr excavator (prefix ycw) service repair manual (ycw00...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 314 e sr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 314 e sr excavator (prefix ycw) service repair manual (ycw000...fhsjejkdm
The document provides instructions for removing and installing engine oil cooler components on a Caterpillar 314E excavator. Key steps include draining coolant, removing bolts and spacers securing the oil cooler, and installing a new gasket. Safety notices emphasize keeping parts clean and containing fluids to prevent contamination.
John deere 26 and 51 inch brooms service repair manualfjjsekkksekmm
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp0...fjjsekkksekmm
This document provides instructions for disassembling and assembling the rear drive and steering axle housing of a Caterpillar 424D backhoe loader. The summary is:
1. The document outlines 18 steps to disassemble the rear axle housing, including draining fluids, removing bolts and pins, measuring components, and extracting seals, bearings, and shafts.
2. Key components that are disassembled include the differential, steering knuckles, axle shaft, sun gear, universal joints, seals, and bushings. Alignment marks should be made to aid reassembly.
3. Detailed illustrations accompany each step to show the location and orientation of parts as they are removed.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing guards and covers, and using lifting equipment to remove the engine. The 18 steps to install the engine describe reversing the removal process and include reconnecting wiring, installing guards and covers, and refilling fluids. The document provides illustrations and references other manuals for some removal and installation procedures.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It describes 17 steps to complete the installation, which include attaching the engine using lifting equipment, installing mounting bolts and other components like the alternator, starter motor, and air conditioning compressor. The final steps include connecting fluids, turning on the battery, and filling coolant and oil. Tools required include a hydraulic jack and load leveling beam.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to release springs carefully due to risk of being struck by propelled parts.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1) How to remove the flywheel by first installing guide bolts and link bracket to support the flywheel, then removing setscrews and taking off the flywheel.
2) The installation procedure which includes cleaning surfaces, heating and installing the ring gear if removed, placing the flywheel on guides and lifting device, and installing and tightening bolts.
3) Removal of the crankshaft rear seal involves taking out setscrews and removing the housing assembly. The seal is non-serviceable so a new assembly must be
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.4 engine. It describes removing the flywheel, installing guide studs, lifting the flywheel housing off with a lifting device, and removing bolts and seals. When installing, it describes cleaning surfaces, installing new seals, aligning the housing, torquing bolts to specified values, and checking the crankshaft alignment. The document is from a service manual and provides detailed step-by-step instructions and illustrations for performing the repair.
Caterpillar cat 420 d backhoe loader (prefix mbh) service repair manual (mbh0...fjjsekkksekmm
This document provides instructions for assembling and disassembling the final drive (rear drive and steering axle) of a 420D Backhoe Loader. It outlines 14 steps for installation, including installing brackets, hoses, pins and other components. 12 steps are provided for removal, such as draining fluid, loosening bolts, and using specialty tools to separate parts. The instructions include illustrations and notes about part weights.
Caterpillar cat 420 d backhoe loader (prefix fdp) service repair manual (fdp1...fjjsekkksekmm
This document provides assembly instructions for a bank valve (loader) on a 420D backhoe loader model. It lists 42 steps to assemble the valve, including installing o-rings, seals, springs, plugs and other components in the proper order and torque specifications. The assembly procedure must be done carefully and cleanly to prevent contamination.
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...fjjsekkksekmm
The document provides instructions for removing and installing a steering cylinder on a 420D backhoe loader. It lists the required tools and steps to remove the cylinder from the axle housing, including removing retaining rings and seals. The assembly procedure details installing the seals and components in reverse order. Additional sections provide instructions for removing tie rods and the rear drive and steering axle assembly.
Case ih magnum 310 tractor service repair manual (pin zjrf94001 and above)fjjsekkksekmm
This document is a service manual for Magnum 250, 280, 310, 340, 310 Rowtrac, and 340 Rowtrac tractors with Powershift Transmissions (PST) from CNH Industrial America LLC. It contains over 50 sections that provide information on systems including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section includes detailed component information, diagrams, specifications, and repair or replacement procedures.
Case 885 b awd tier 0 tier 1 tier 2 tier 3 graders service repair manualfjjsekkksekmm
This document provides information about engines for various grader models. It includes sections on engine diagnostic tools, fails diagnostics for engines that fail to start, and specifications for Tier 3 engines. Torque specifications and adjustments are also listed for components like the fuel injection pump, injectors, and turbocharger.
Case 845 b grader service repair manualfjjsekkksekmm
The document provides technical details about CNH America LLC engines, including:
- It describes the main components of the 667TA engines used in various Case grader models, including the turbocharger, alternator, water pump, ECU, and fuel filter.
- The engine block is made of cast iron with cylinders, journals, and mounts for other components. The crankshaft has journals, gears, counterweights, and mounts. Connecting rods are forged steel.
- Additional details are given about the cylinder bores, main journals, camshaft bearing mounts, lubrication and cooling passages, and stiffening plate in the engine block. The crankshaft, oil pump gear,
The document is a service manual that provides removal and installation instructions for various components of 845-865-885 grader machines, including:
- Charge air cooler removal and installation procedures.
- Removal and installation instructions for starters and alternators, including torque specifications for fasteners.
- Diagrams illustrating the component locations.
The manual contains detailed part numbers, specifications and safety information to correctly service the machines. Sections cover topics such as electrical, steering, power train, brakes, hydraulics and mounted equipment systems.
More Related Content
Similar to Caterpillar cat 416 f2 backhoe loader (prefix hwb) service repair manual (hwb00001 and up)
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove the keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, and the springs and keepers are compressed into place using the tool. The engine oil filter base and engine oil cooler are also removed and installed, following steps to drain fluids, remove bolts and gaskets, and clean components.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The procedure involves using specialized tools to compress the valve springs to remove and install valve keepers. Safety precautions are outlined to prevent injury from the force of compressed springs. Instructions are also given for removing and installing the engine oil filter base, which involves draining oil and replacing gaskets.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. For installation, the valves are lubricated and inserted into the cylinder head, new seals are installed on the guides, springs and retainers are compressed using the tool and keepers are installed. The engine oil filter base and engine oil cooler are also removed and installed, following cleaning and installation of new gaskets.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...fjjskekfkskemf
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 416F backhoe loader. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. The installation procedure specifies cleaning components, lubricating valve stems, compressing springs with the tool to insert keepers, and installing the valves in the proper positions. A separate section also outlines removing and installing the engine oil filter base.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...ifksjejdkemm
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 416F backhoe loader. The removal procedure involves using a valve spring compressor tool to compress the springs, remove the keepers, and take out the valves. The installation procedure specifies cleaning and inspecting components, lubricating the valve stems, and using the compressor tool to reinstall the valves and springs. Proper tools and safety precautions are highlighted. A second section details removing and installing the engine oil filter base, including draining oil and replacing gaskets.
Caterpillar cat 314 e lcr excavator (prefix ycw) service repair manual (ycw00...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 314 e sr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 314 e sr excavator (prefix ycw) service repair manual (ycw000...fhsjejkdm
The document provides instructions for removing and installing engine oil cooler components on a Caterpillar 314E excavator. Key steps include draining coolant, removing bolts and spacers securing the oil cooler, and installing a new gasket. Safety notices emphasize keeping parts clean and containing fluids to prevent contamination.
Similar to Caterpillar cat 416 f2 backhoe loader (prefix hwb) service repair manual (hwb00001 and up) (8)
John deere 26 and 51 inch brooms service repair manualfjjsekkksekmm
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp0...fjjsekkksekmm
This document provides instructions for disassembling and assembling the rear drive and steering axle housing of a Caterpillar 424D backhoe loader. The summary is:
1. The document outlines 18 steps to disassemble the rear axle housing, including draining fluids, removing bolts and pins, measuring components, and extracting seals, bearings, and shafts.
2. Key components that are disassembled include the differential, steering knuckles, axle shaft, sun gear, universal joints, seals, and bushings. Alignment marks should be made to aid reassembly.
3. Detailed illustrations accompany each step to show the location and orientation of parts as they are removed.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing guards and covers, and using lifting equipment to remove the engine. The 18 steps to install the engine describe reversing the removal process and include reconnecting wiring, installing guards and covers, and refilling fluids. The document provides illustrations and references other manuals for some removal and installation procedures.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It describes 17 steps to complete the installation, which include attaching the engine using lifting equipment, installing mounting bolts and other components like the alternator, starter motor, and air conditioning compressor. The final steps include connecting fluids, turning on the battery, and filling coolant and oil. Tools required include a hydraulic jack and load leveling beam.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to release springs carefully due to risk of being struck by propelled parts.
The document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes:
1) How to remove the flywheel by first installing guide bolts and link bracket to support the flywheel, then removing setscrews and taking off the flywheel.
2) The installation procedure which includes cleaning surfaces, heating and installing the ring gear if removed, placing the flywheel on guides and lifting device, and installing and tightening bolts.
3) Removal of the crankshaft rear seal involves taking out setscrews and removing the housing assembly. The seal is non-serviceable so a new assembly must be
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.4 engine. It describes removing the flywheel, installing guide studs, lifting the flywheel housing off with a lifting device, and removing bolts and seals. When installing, it describes cleaning surfaces, installing new seals, aligning the housing, torquing bolts to specified values, and checking the crankshaft alignment. The document is from a service manual and provides detailed step-by-step instructions and illustrations for performing the repair.
Caterpillar cat 420 d backhoe loader (prefix mbh) service repair manual (mbh0...fjjsekkksekmm
This document provides instructions for assembling and disassembling the final drive (rear drive and steering axle) of a 420D Backhoe Loader. It outlines 14 steps for installation, including installing brackets, hoses, pins and other components. 12 steps are provided for removal, such as draining fluid, loosening bolts, and using specialty tools to separate parts. The instructions include illustrations and notes about part weights.
Caterpillar cat 420 d backhoe loader (prefix fdp) service repair manual (fdp1...fjjsekkksekmm
This document provides assembly instructions for a bank valve (loader) on a 420D backhoe loader model. It lists 42 steps to assemble the valve, including installing o-rings, seals, springs, plugs and other components in the proper order and torque specifications. The assembly procedure must be done carefully and cleanly to prevent contamination.
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...fjjsekkksekmm
The document provides instructions for removing and installing a steering cylinder on a 420D backhoe loader. It lists the required tools and steps to remove the cylinder from the axle housing, including removing retaining rings and seals. The assembly procedure details installing the seals and components in reverse order. Additional sections provide instructions for removing tie rods and the rear drive and steering axle assembly.
Case ih magnum 310 tractor service repair manual (pin zjrf94001 and above)fjjsekkksekmm
This document is a service manual for Magnum 250, 280, 310, 340, 310 Rowtrac, and 340 Rowtrac tractors with Powershift Transmissions (PST) from CNH Industrial America LLC. It contains over 50 sections that provide information on systems including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section includes detailed component information, diagrams, specifications, and repair or replacement procedures.
Case 885 b awd tier 0 tier 1 tier 2 tier 3 graders service repair manualfjjsekkksekmm
This document provides information about engines for various grader models. It includes sections on engine diagnostic tools, fails diagnostics for engines that fail to start, and specifications for Tier 3 engines. Torque specifications and adjustments are also listed for components like the fuel injection pump, injectors, and turbocharger.
Case 845 b grader service repair manualfjjsekkksekmm
The document provides technical details about CNH America LLC engines, including:
- It describes the main components of the 667TA engines used in various Case grader models, including the turbocharger, alternator, water pump, ECU, and fuel filter.
- The engine block is made of cast iron with cylinders, journals, and mounts for other components. The crankshaft has journals, gears, counterweights, and mounts. Connecting rods are forged steel.
- Additional details are given about the cylinder bores, main journals, camshaft bearing mounts, lubrication and cooling passages, and stiffening plate in the engine block. The crankshaft, oil pump gear,
The document is a service manual that provides removal and installation instructions for various components of 845-865-885 grader machines, including:
- Charge air cooler removal and installation procedures.
- Removal and installation instructions for starters and alternators, including torque specifications for fasteners.
- Diagrams illustrating the component locations.
The manual contains detailed part numbers, specifications and safety information to correctly service the machines. Sections cover topics such as electrical, steering, power train, brakes, hydraulics and mounted equipment systems.
John deere 318 d skid steer loader (eh controls) service repair manual (tm11407)fjjsekkksekmm
This document provides safety information and instructions for technicians working on 318D, 319D, 320D, and 323D skid steer loaders. It emphasizes the importance of following all safety precautions when inspecting or servicing the machine, including wearing protective equipment, avoiding contact with moving parts and high pressure fluids, preventing fires, and working in a ventilated area to avoid exhaust inhalation. Technicians are instructed to thoroughly read all safety messages in the manual and on the machine before performing any work.
John deere 54, 60 and 72 inch mid mount mowers service repair manualfjjsekkksekmm
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John deere 47 and 59 snowbowers service repair manualfjjsekkksekmm
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including various mowers, tillers, blades, brooms, and snowblowers. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John deere 31 b post hole digger service repair manualfjjsekkksekmm
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
Zodiac Signs and Food Preferences_ What Your Sign Says About Your Tastemy Pandit
Know what your zodiac sign says about your taste in food! Explore how the 12 zodiac signs influence your culinary preferences with insights from MyPandit. Dive into astrology and flavors!
How to Implement a Real Estate CRM SoftwareSalesTown
To implement a CRM for real estate, set clear goals, choose a CRM with key real estate features, and customize it to your needs. Migrate your data, train your team, and use automation to save time. Monitor performance, ensure data security, and use the CRM to enhance marketing. Regularly check its effectiveness to improve your business.
3 Simple Steps To Buy Verified Payoneer Account In 2024SEOSMMEARTH
Buy Verified Payoneer Account: Quick and Secure Way to Receive Payments
Buy Verified Payoneer Account With 100% secure documents, [ USA, UK, CA ]. Are you looking for a reliable and safe way to receive payments online? Then you need buy verified Payoneer account ! Payoneer is a global payment platform that allows businesses and individuals to send and receive money in over 200 countries.
If You Want To More Information just Contact Now:
Skype: SEOSMMEARTH
Telegram: @seosmmearth
Gmail: seosmmearth@gmail.com
B2B payments are rapidly changing. Find out the 5 key questions you need to be asking yourself to be sure you are mastering B2B payments today. Learn more at www.BlueSnap.com.
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...my Pandit
Dive into the steadfast world of the Taurus Zodiac Sign. Discover the grounded, stable, and logical nature of Taurus individuals, and explore their key personality traits, important dates, and horoscope insights. Learn how the determination and patience of the Taurus sign make them the rock-steady achievers and anchors of the zodiac.
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...Neil Horowitz
On episode 272 of the Digital and Social Media Sports Podcast, Neil chatted with Brian Fitzsimmons, Director of Licensing and Business Development for Barstool Sports.
What follows is a collection of snippets from the podcast. To hear the full interview and more, check out the podcast on all podcast platforms and at www.dsmsports.net
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....Lacey Max
“After being the most listed dog breed in the United States for 31
years in a row, the Labrador Retriever has dropped to second place
in the American Kennel Club's annual survey of the country's most
popular canines. The French Bulldog is the new top dog in the
United States as of 2022. The stylish puppy has ascended the
rankings in rapid time despite having health concerns and limited
color choices.”
Discover timeless style with the 2022 Vintage Roman Numerals Men's Ring. Crafted from premium stainless steel, this 6mm wide ring embodies elegance and durability. Perfect as a gift, it seamlessly blends classic Roman numeral detailing with modern sophistication, making it an ideal accessory for any occasion.
https://rb.gy/usj1a2
Company Valuation webinar series - Tuesday, 4 June 2024FelixPerez547899
This session provided an update as to the latest valuation data in the UK and then delved into a discussion on the upcoming election and the impacts on valuation. We finished, as always with a Q&A
Industrial Tech SW: Category Renewal and CreationChristian Dahlen
Every industrial revolution has created a new set of categories and a new set of players.
Multiple new technologies have emerged, but Samsara and C3.ai are only two companies which have gone public so far.
Manufacturing startups constitute the largest pipeline share of unicorns and IPO candidates in the SF Bay Area, and software startups dominate in Germany.
Part 2 Deep Dive: Navigating the 2024 Slowdownjeffkluth1
Introduction
The global retail industry has weathered numerous storms, with the financial crisis of 2008 serving as a poignant reminder of the sector's resilience and adaptability. However, as we navigate the complex landscape of 2024, retailers face a unique set of challenges that demand innovative strategies and a fundamental shift in mindset. This white paper contrasts the impact of the 2008 recession on the retail sector with the current headwinds retailers are grappling with, while offering a comprehensive roadmap for success in this new paradigm.
Navigating the world of forex trading can be challenging, especially for beginners. To help you make an informed decision, we have comprehensively compared the best forex brokers in India for 2024. This article, reviewed by Top Forex Brokers Review, will cover featured award winners, the best forex brokers, featured offers, the best copy trading platforms, the best forex brokers for beginners, the best MetaTrader brokers, and recently updated reviews. We will focus on FP Markets, Black Bull, EightCap, IC Markets, and Octa.
Structural Design Process: Step-by-Step Guide for BuildingsChandresh Chudasama
The structural design process is explained: Follow our step-by-step guide to understand building design intricacies and ensure structural integrity. Learn how to build wonderful buildings with the help of our detailed information. Learn how to create structures with durability and reliability and also gain insights on ways of managing structures.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER HWB
Configuration: 416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820268
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove"
for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bottom mating surface of the cylinder head. Check the depth of the valves below
the face of the cylinder head before the valve springs are removed. Refer to Specifications,
"Cylinder Head Valves" for the correct dimensions.
1/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Note: Inlet valves have a recess in the center of the head.
3. Use a suitable lifting device to position the cylinder head with the valve springs upward.
The weight of the cylinder head is approximately 65 kg (143 lb).
Note: Ensure that the cylinder head is kept on a clean, soft surface in order to prevent
damage to the machined face.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 1 g02511756
2/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Install Tooling (A) in position on the cylinder head in order to compress appropriate valve
spring (3).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (A) in order to remove valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
6. Slowly release pressure on Tooling (A).
Illustration 2 g02511676
7. Place a temporary identification mark on valve spring (3) in order to identify the correct
position.
8. Remove valve spring retainer (2). Remove valve spring (3).
9. Repeat Step 4 through Step 8 for the remaining valves.
3/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove Tooling (A).
11. Remove valve stem seals (4).
12. Use a suitable lifting device in order to carefully turn over the cylinder head.
13. Remove valves (5).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The valves have a hard surface finish. Grinding compound must not be used on the valves.
Grinding compound will damage the hard surface finish of the valves.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow Step
1.a through Step 1.d in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to System Operation,
Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure.
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and System Operation, Testing and Adjusting, "Valve Guide - Inspect"
for further information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves" for further information.
e. Inspect valve springs (3) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves " for further information.
4/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g02511676
2. Lubricate the stems of valves (5) with clean engine oil. Install valves (5) in the appropriate
positions in the cylinder head. Check the depth of the valves below the face of the cylinder
head. Refer to System Operation, Testing and Adjusting, "Valve Depth - Inspect" for more
information.
3. Use a suitable lifting device in order to carefully turn over the cylinder head. The weight of
the cylinder head is approximately 65 kg (143 lb).
Note: Ensure that all of the valves remain in place.
4. Install new valve stem seals (4) onto each of the valve guides.
Note: The outer face of the valve guides must be clean and dry before installing valve stem
seals (4).
5. Install valve spring (3) onto the cylinder head. Position valve spring retainer (2) on valve
spring (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
5/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 4 g02511756
6. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (3).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
7. Apply sufficient pressure to Tooling (A) in order to install valve keepers (1).
Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal
(4).
6/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
8. Carefully release the pressure on Tooling (A).
9. Repeat Step 5 through Step 8 for the remaining valves.
10. Remove Tooling (A) from the cylinder head.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for
the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:15:49 UTC+0800 2019
7/7416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER HWB
Configuration: 416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820269
Engine Oil Filter Base - Remove and Install
SMCS - 1306-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Strap Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g02475535
1. Place a suitable container below engine oil filter base (5) in order to catch any oil that might
be spilled.
2. Use Tooling (A) to remove engine oil filter (5). Refer to Operation and Maintenance
Manual, "Engine Oil and Filter - Change" for the correct procedure.
3. Remove bolts (3).
4. Remove engine oil filter base (4).
5. Remove gasket (6).
6. If necessary, remove plug (1) from engine oil filter base (4). Remove O-ring seal (2) from
plug (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g02475535
1. Clean engine oil filter base (4). Clean the gasket surfaces of the cylinder block.
2. If necessary, install new O-ring seals (2) to plugs (1). Install plugs (1) to engine oil filter
base (4). Tighten the plugs to a torque of 12 N·m (106 lb in).
3. Install bolts (3) to engine oil filter base (4).
4. Install a gasket (6) onto bolts (3). Install the assembly of the engine oil filter base to the
cylinder block.
5. Tighten bolts (3) to a torque of 22 N·m (195 lb in).
6. Install a new engine oil filter (5) and check the level of the engine lubricating oil. Refer to
Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:16:46 UTC+0800 2019
3/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER HWB
Configuration: 416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820270
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly,
"Electronic Control Module - Remove" for the correct procedure.
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorized personnel that have the correct
training.
Before beginning ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to System Operation, Testing and Adjusting, "Cleanliness of
Fuel System Components" for detailed information on the standards of
cleanliness that must be observed during ALL work on the fuel system.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container. Refer to Operation and
Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.
Illustration 1 g03701812
2/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g02475493
2. Remove spacer (1) (not shown) from the cylinder block.
3. Remove bolt (2) from the assembly of engine oil cooler (3).
Note: Support the engine oil cooler as the bolts are removed.
4. Remove the assembly of engine oil cooler (3) from the cylinder block.
5. Remove gasket (4) from engine oil cooler (3).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:17:43 UTC+0800 2019
3/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER HWB
Configuration: 416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820271
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02475493
1/4416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g03701812
1. Ensure that engine cooler (3) is clean and free from damage. Ensure that the engine oil
cooler is free from restriction.
2. Clean the gasket surfaces of the cylinder block.
3. Position a new gasket (4) onto engine oil cooler (3).
4. Push bolts (1) through the holes in the gasket.
Note: The holes in the gasket have serrations that hold the bolts captive.
5. Position engine oil cooler (3) onto the cylinder block. Hand tighten bolts (2). Support the
engine oil cooler as the bolts are installed.
2/4416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Illustration 3 g03741794
Snug torque tightening sequence for the engine oil cooler
6. Tighten the bolts to a snug torque of 7.5 N·m (66) in the sequence that is shown in
Illustration 3.
3/4416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 4 g03736218
Tightening sequence for the engine oil cooler
7. Tighten the bolts to a torque of 26 N·m (230 lb in) in the sequence that is shown in
Illustration 4.
8. Install spacer (1) (not shown). Tighten the bolts to a torque of 44 N·m (32 lb ft). Refer to
Illustration 2
End By:
a. Install the Electronic Control Module (ECM). Refer to Disassembly and Assembly,
"Electronic Control Module - Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:18:39 UTC+0800 2019
4/4416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER HWB
Configuration: 416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820272
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g02476517
1. Remove bolts (2). Remove suction pipe (1) from engine oil pump (4).
2. Remove gasket (3).
3. Remove bolts (5) and remove the assembly of engine oil pump (4) from the cylinder block.
2/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g02476518
4. If necessary, follow Step 4.a through Step 4.d in order to disassembly engine oil pump (4).
a. Remove bolts (9) from front cover assembly (8).
b. Remove front cover assembly (8) from the housing of the engine oil pump (4).
c. Remove outer rotor (7) from the housing of engine oil pump (4).
d. Do not remove dowel (6) from the housing of engine oil pump (4) unless the dowels
are damaged.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:19:36 UTC+0800 2019
3/3416F2 Center Pivot Backhoe Loader HWB00001-UP (MACHINE) POWERED BY C...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...