This document provides instructions for disassembling and assembling the travel motor of a 345B II Excavator. Key steps include:
1. Cleaning all parts to prevent contamination of the hydraulic system.
2. Removing components like the head, plates, seals and pistons from the travel motor housing.
3. Separating additional components like the rotating group, shaft and barrel.
4. Reassembling components in reverse order, making sure to clean and replace seals, apply lubricant and torque fasteners to specification. Proper orientation of parts like washers is important for correct assembly.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...zatao0179249295
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts back onto the shaft assembly.
3. Measuring clearances and installing spacers to the proper specifications.
The instructions emphasize cleaning parts and applying lubricants before assembly to prevent contaminating the hydraulic system.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on Models 345B and 345B L Series II Excavators. It outlines 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and rotating group. It also lists the required tools and safety notices for the job. The summary is meant to give a high-level overview of the key details while being brief.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts.
3. Measuring clearances during assembly to ensure correct orientation and fit of parts.
The instructions emphasize cleaning parts and applying lubricant before assembly to prevent contamination of hydraulic systems. Notes provide additional guidance on inspecting parts and using new components when required.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify torque settings for assembling the various components in the correct orientation and order. Cleaning and inspection of parts is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...zatao0179249295
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts back onto the shaft assembly.
3. Measuring clearances and installing spacers to the proper specifications.
The instructions emphasize cleaning parts and applying lubricants before assembly to prevent contaminating the hydraulic system.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on Models 345B and 345B L Series II Excavators. It outlines 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and rotating group. It also lists the required tools and safety notices for the job. The summary is meant to give a high-level overview of the key details while being brief.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...luanxianshi27
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the rotating group including installing piston assemblies, bearings and other parts.
3. Measuring clearances during assembly to ensure correct orientation and fit of parts.
The instructions emphasize cleaning parts and applying lubricant before assembly to prevent contamination of hydraulic systems. Notes provide additional guidance on inspecting parts and using new components when required.
Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify the proper orientation and torque specifications for each component. Cleanliness of parts and applying lubricant is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix ALB) Service Repair Manual (...wfu089267
The document provides instructions for assembling a travel motor for an excavator model 345B II. Key steps include:
1. Installing seals, plugs and other components back into the travel motor housing.
2. Assembling the barrel assembly including installing washers, spacers, piston assemblies and retainer.
3. Installing the cam plate and bearing onto the shaft and assembling the rotating group.
The instructions provide detailed illustrations and specify torque settings for assembling the various components in the correct orientation and order. Cleaning and inspection of parts is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...zatao0179249295
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It begins by listing the required tools. The disassembly process involves removing 31 individual parts from the travel motor in a specific sequence. The assembly section then provides instructions for reinstalling the parts in the reverse order, noting proper installation of seals, washers, and other components. Safety notices are included regarding cleanliness, contamination prevention, and inspection of parts.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, rotating group, brake piston, plates and seals. It then lists 29 steps to reassemble the travel motor by installing components in the reverse order, and provides notes about cleaning, lubricating and replacing parts as needed. Tools required are also listed.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar cat 345 c l excavator (prefix tba) service repair manual (tba0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
More Related Content
Similar to Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual (ALB00001 and up).pdf
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...luanxianshi27
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It begins by listing the required tools. The disassembly process involves removing 31 individual parts from the travel motor in a specific sequence. The assembly section then provides instructions for reinstalling the parts in the reverse order, noting proper installation of seals, washers, and other components. Safety notices are included regarding cleanliness, contamination prevention, and inspection of parts.
Caterpillar Cat 345B Series II Excavator (Prefix AKX) Service Repair Manual (...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps to disassemble the travel motor by removing components like the head, rotating group, brake piston, plates and seals. It then lists 29 steps to reassemble the travel motor by installing components in the reverse order, and provides notes about cleaning, lubricating and replacing parts as needed. Tools required are also listed.
Caterpillar Cat 345B L Series II Excavator (Prefix AKX) Service Repair Manual...wfu089267
This document provides step-by-step instructions for disassembling and assembling the travel motor on a 345B and 345B L Series II Excavator. It lists 31 steps for disassembly, removing components like the head, plates, seals, and rotating group. It then lists 29 steps for assembly, replacing components in reverse order and noting to clean parts, apply lubricant, and replace all seals and gaskets. Cautions are provided about handling parts carefully and reinstalling them in their original locations and orientations.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs to reverse the disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar cat 345 c l excavator (prefix tba) service repair manual (tba0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Similar to Caterpillar Cat 345B L Series II Excavator (Prefix ALB) Service Repair Manual (ALB00001 and up).pdf (17)
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
141 kg (310 lb).
Illustration 1 g00627438
2. Remove displacement change valve (1) from the head of the travel motor.
3/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00624938
3. Remove three O-ring seals (2) and two rings (3) from the displacement change valve.
Illustration 3 g00628657
4. Remove three plugs (5) from the head. Remove an O-ring seal from each plug.
5. Remove six outer bolts (4) from the head of the travel motor.
Illustration 4 g00624949
4/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use Tooling (A) and a suitable lifting device to remove the head of the travel motor from
the travel motor housing. The head weighs 43 kg (95 lb).
Note: There are three pins (7) that may fall out of the inside of the head when the head is
removed.
Note: Be careful during the removal of head (6) from the travel motor housing. Be careful
not to scratch mating surfaces or damage the mating surfaces of the components.
Illustration 5 g00624953
7. Turn over the head. If three pins (7) are in the bottom side of the head, remove the pins.
Illustration 6 g00627405
8. Remove port plate (8) and O-ring seal (9) from the head.
5/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00625967
9. Use Tooling (B) in order to remove bearing (10) from the head of the travel motor.
Illustration 8 g00627391
10. Remove plate (11) and remove springs (12) from the travel motor housing.
11. Remove O-ring seals (13) from the upper surface of the travel motor housing.
Illustration 9 g00627377
6/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 12. Install Tooling (C) on the brake piston (14). Remove the brake piston.
Illustration 10 g00625888
13. Remove O-ring seals (15) and the backup rings from the brake piston.
Note: Make sure that you take note of the location of the O-rings versus the backup rings.
Illustration 11 g00625891
14. Remove six separator plates (16) from the travel motor housing.
7/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00666743
15. Remove five friction disks (17) from the travel motor housing.
Illustration 13 g00626837
16. Install Tooling (D) to the shaft and use a suitable lifting device in order to remove the
rotating group from the travel motor housing. The weight of the rotating group is 29 kg (65
lb).
Note: Do not allow the components of the rotating group to come apart during the removal
from the travel motor. All of the components in the rotating group must be reinstalled in the
component's original location.
8/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00626633
17. Turn over the rotating group. Remove shaft assembly (18) from the rotating group.
Illustration 15 g00666621
Illustration 16 g00625900
18. Use a suitable press to remove bearing (19) from shaft (18) .
9/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g00666622
19. Use Tool (E) and a suitable press in order to remove inner race (20) from shaft (18) .
Illustration 18 g00625908
20. Remove cam plate (21) from the rotating group.
Illustration 19 g00625911
10/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 21. Retainer (22) and piston assemblies (23) are not serviced separately. Prior to the removal of
the retainer and the piston assemblies from barrel (24), put identification marks on the
piston assemblies, the retainer and the barrel for assembly purposes.
22. The piston assemblies must be reinstalled in the original bores in the retainer and the barrel.
23. Remove retainer (22) and piston assemblies (23) from barrel (24) .
24. Separate the piston assemblies from the retainer.
Illustration 20 g00625917
Note: The orientation of the four washers (25) is important. The four washers must be
reinstalled on barrel (24) in the same orientation.
25. Remove guide (26) and outer spacer (27) from barrel (24) .
26. Remove four washers (25) and inner spacer (28) from the barrel.
Illustration 21 g00625937
27. Remove two keys (29) from the travel motor housing.
11/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g00625920
28. Use Tooling (F) to remove retaining ring (30) from the shaft end of the travel motor
housing.
Illustration 23 g00625936
Illustration 24 g00636454
29. Use Tooling (G) to remove lip type seal (31) from the travel motor housing if the shaft has
been removed from the travel motor.
12/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 30. Use Tooling (H) to remove lip type seal (31) if the shaft has not been removed from the
travel motor. Place the travel motor in a vertical position when you use Tooling (H) to
remove the lip type seal.
Illustration 25 g00625976
31. Remove plug (33) and piston (32) from the travel motor housing. Remove O-ring seal (34)
from the plug.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 17:46:18 UTC+0800 2020
13/13
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR ALB
Configuration: 345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i01324820
Travel Motor - Assemble - Series II
SMCS - 4351-016
S/N - AGS1-UP
S/N - AKJ1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Assembly Procedure
Table 1
1/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Required Tools
Tool Part Number Part Description Qty
(A) 180-6533 Seal Driver 1
(B) 6V-7030 Micrometer Depth Gauge 1
(C) 8T-0447 Calipers 1
(D) 4C-8359 Eyebolt 1
(E) 1P-0510 Driver Group 1
(F) 3E-3879 Eyebolt 1
(G) 1P-1862 Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
2/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00631019
1. Install O-ring seal (36) on plug (35) .
2. Install piston (34) and the plug in the travel motor body. Tighten the plug to a torque of 430
± 40 N·m (317 ± 30 lb ft).
Illustration 2 g00630992
Illustration 3 g00636553
3/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 3. Apply a thin coat of 4C-4030 Thread Lock Compound on the outer surfaces of lip type seal
(33) .
4. Use Tooling (A) and a suitable hammer to drive the lip type seal into the travel motor body.
Drive the seal downward until Tooling (A) makes contact with the travel motor housing.
5. Use Tooling (G) to install retaining ring (32) to the shaft end of the travel motor body.
Illustration 4 g00630986
6. Install two keys (31) inside the travel motor body.
Illustration 5 g00629434
7. Assemble washers (29), inner spacer (30) and outer spacer (28) in the proper orientation, as
shown.
4/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g00628110
8. Use Tooling (B) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
Illustration 7 g00625917
9. Install inner spacer (28), four washers (25), and outer spacer (27) to barrel (24) .
10. Install guide (26) to the barrel.
5/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24) .
Illustration 9 g00625908
12. Install cam plate (21) on the barrel assembly.
Illustration 10 g00666621
6/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft (18) .
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft (18) .
Note: Place the two support plates under the lip of shaft (18) .
7/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g00626633
15. Insert shaft (18) in the barrel assembly.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate five friction disks (17) and six separator plates (16) into the travel motor housing.
Start with a separator plate and end with a separator plate.
8/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g00628965
18. Use Tooling (C) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 38 ± 2 mm (1.5 ± 0.08 inch). If
this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
9/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C Eng...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
10/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g00629060
21. Use Tooling (C) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1 mm (0.82 ± 0.04 inch). If
this measurement is off, drive the brake piston further into the travel motor body.
11/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 22 g00627391
22. Install springs (12) and plate (11) .
23. Install O-ring seals (13) .
Illustration 23 g00629646
24. Use Tooling (E) to drive the bearing into the head.
Illustration 24 g00627405
12/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g00629613
27. Turn over head (6). Install Tooling (F) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install three dowels (7) into the head.
13/15
345B L Series II Excavators ALB00001-UP (MACHINE) POWERED BY 3176C E...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...