This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar cat 345 c excavator (prefix tba) service repair manual (tba00001 ...fjsekqazxkdmmem
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper cleaning and installation of identification marks are emphasized to ensure correct reassembly of components in their original locations.
Caterpillar cat 345 c l excavator (prefix tba) service repair manual (tba0000...fjjskqazxedmmem
This document provides instructions for disassembling and assembling the travel motor of a 345C excavator. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure describes 33 steps to reinstall these parts in reverse order, noting that components must be cleaned and new seals used. Proper tooling and torque specifications are listed for each step.
Caterpillar cat 345 c excavator (prefix tba) service repair manual (tba00001 ...fjskekmdm
This document provides instructions for disassembling and assembling the travel motor of a 345C excavator. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure describes 33 steps to reinstall these parts in reverse order, noting that components must be cleaned and new seals used. Proper tooling and torque specifications are listed for each step.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove components from the travel motor like the head, plates, disks, piston assemblies, seals and more. The assembly procedure involves 13 steps like installing seals, spacers, keys and plugs to rebuild the travel motor. Precise measurements are required and parts must be cleaned to prevent contamination of the hydraulic system.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, port plate, brake piston, disks, and seals. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, washers, and plugs. Proper cleaning, identification of parts, and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar cat 345 c excavator (prefix tba) service repair manual (tba00001 ...fjsekqazxkdmmem
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper cleaning and installation of identification marks are emphasized to ensure correct reassembly of components in their original locations.
Caterpillar cat 345 c l excavator (prefix tba) service repair manual (tba0000...fjjskqazxedmmem
This document provides instructions for disassembling and assembling the travel motor of a 345C excavator. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure describes 33 steps to reinstall these parts in reverse order, noting that components must be cleaned and new seals used. Proper tooling and torque specifications are listed for each step.
Caterpillar cat 345 c excavator (prefix tba) service repair manual (tba00001 ...fjskekmdm
This document provides instructions for disassembling and assembling the travel motor of a 345C excavator. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure describes 33 steps to reinstall these parts in reverse order, noting that components must be cleaned and new seals used. Proper tooling and torque specifications are listed for each step.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove components from the travel motor like the head, plates, disks, piston assemblies, seals and more. The assembly procedure involves 13 steps like installing seals, spacers, keys and plugs to rebuild the travel motor. Precise measurements are required and parts must be cleaned to prevent contamination of the hydraulic system.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, port plate, brake piston, disks, and seals. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, washers, and plugs. Proper cleaning, identification of parts, and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar cat 345 c l excavator (prefix bwy) service repair manual (bwy0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove components from the travel motor like the head, plates, disks, pistons, seals and bearings. The assembly procedure involves 13 steps like installing seals, spacers, pistons and plugs to rebuild the travel motor. Proper cleaning, identification of parts and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove components from the travel motor like the head, plates, disks, piston assemblies, seals and more. The assembly procedure involves 13 steps like installing seals, spacers, keys and plugs to rebuild the travel motor. Precise measurements are required and parts must be cleaned to prevent contamination of the hydraulic system.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar cat 345 c excavator (prefix bwy) service repair manual (bwy00001 ...fjkkekmdm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...ze3xiandiao
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It details 34 steps for installing various parts like pistons, springs, seals and bearings into the pump housing.
2. Proper cleaning and lubrication of parts is emphasized before assembly. Tools are listed and various safety warnings are provided about spring loaded parts.
3. Once assembled, the pump is installed on the tractor using bolts and hoses are connected to the manifold. Proper lifting and containment of fluids is advised during the process.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the engine cylinder head
The procedures describe draining fluids, using specialty tools to remove and install parts, cleaning components, lubricating seals, and torquing bolts to the specified values. Technicians are advised to take precautions to prevent spills and contamination when working on the fuel system.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap to connect fittings, removing and installing the muffler, removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing and installing the primary fuel filter base.
2) The procedures include identifying required tools, disconnecting lines and electrical connections, removing mounting hardware, and installing components in reverse order while following specific torque specifications.
3) Safety precautions are provided, such as relieving system pressure before disconnecting lines and wearing protective equipment when working with components under spring force.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes in detail how to separate the transmission from the torque converter, disassemble the individual components of the torque converter, and disassemble the transmission by removing the shafts, gears, seals, and clutch packs. The instructions are accompanied by diagrams and callouts to ensure proper reassembly.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yqen95561858
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
More Related Content
Similar to Caterpillar Cat 345C Excavator (Prefix TBA) Service Repair Manual (TBA00001 and up).pdf
Caterpillar cat 345 c l excavator (prefix bwy) service repair manual (bwy0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove components from the travel motor like the head, plates, disks, pistons, seals and bearings. The assembly procedure involves 13 steps like installing seals, spacers, pistons and plugs to rebuild the travel motor. Proper cleaning, identification of parts and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove components from the travel motor like the head, plates, disks, piston assemblies, seals and more. The assembly procedure involves 13 steps like installing seals, spacers, keys and plugs to rebuild the travel motor. Precise measurements are required and parts must be cleaned to prevent contamination of the hydraulic system.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar cat 345 c excavator (prefix bwy) service repair manual (bwy00001 ...fjkkekmdm
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...ze3xiandiao
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Similar to Caterpillar Cat 345C Excavator (Prefix TBA) Service Repair Manual (TBA00001 and up).pdf (10)
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It details 34 steps for installing various parts like pistons, springs, seals and bearings into the pump housing.
2. Proper cleaning and lubrication of parts is emphasized before assembly. Tools are listed and various safety warnings are provided about spring loaded parts.
3. Once assembled, the pump is installed on the tractor using bolts and hoses are connected to the manifold. Proper lifting and containment of fluids is advised during the process.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine. It includes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, engine oil cooler, and engine oil pump. The document lists the required tools and safety precautions for each procedure and provides illustrations of the components and installation steps.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the engine cylinder head
The procedures describe draining fluids, using specialty tools to remove and install parts, cleaning components, lubricating seals, and torquing bolts to the specified values. Technicians are advised to take precautions to prevent spills and contamination when working on the fuel system.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap to connect fittings, removing and installing the muffler, removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing and installing the primary fuel filter base.
2) The procedures include identifying required tools, disconnecting lines and electrical connections, removing mounting hardware, and installing components in reverse order while following specific torque specifications.
3) Safety precautions are provided, such as relieving system pressure before disconnecting lines and wearing protective equipment when working with components under spring force.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes in detail how to separate the transmission from the torque converter, disassemble the individual components of the torque converter, and disassemble the transmission by removing the shafts, gears, seals, and clutch packs. The instructions are accompanied by diagrams and callouts to ensure proper reassembly.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yqen95561858
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...yqen95561858
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix RGD) Service Repair Manual (RGD00001...yqen95561858
The document provides instructions for disassembling and assembling a travel motor. It begins with safety notices and required tools. The disassembly procedure describes 31 steps to remove components from the travel motor like the head, plates, seals, pistons and housing. The assembly procedure describes 13 steps to reinstall these components in reverse order, noting to clean parts and apply new seals and lubricants. Proper identification and orientation of parts is emphasized to avoid damage.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual (RAE00001...yqen95561858
The document provides instructions for disassembling and assembling a 345D L excavator travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, piston assemblies. It then lists 13 steps for assembly, including installing seals, spacers, washers, and plugs in the proper orientation and torque specifications. Tools required are listed in tables for both disassembly and assembly. Cautions are provided about cleaning parts and preventing contamination of hydraulic components.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...yqen95561858
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...yqen95561858
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and multi-step procedures involving removing and installing various components like bolts, seals, gears, and bearings.
3. Precise instructions are given regarding tool usage, component orientation, and torque specifications to correctly disassemble and reassemble the rear of the engine.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix PJW) Service Repair Manual...yqen95561858
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...yqen95561858
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR TBA
Configuration: 345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i02407350
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
B 1P-0074 Slide Hammer Puller 1
C 6V-3010 Puller Group 1
D 4C-8359 Eyebolt 1
E 9S-9152 Bearing Puller 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
H 1U-7600 Slide Hammer Puller 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage to the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed into the same location. Never force parts during
assembly. Keep parts clean and lubricated.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
2/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
141 kg (310 lb).
Illustration 1 g00627438
2. Remove displacement change valve (1) from the head of the travel motor.
Illustration 2 g00624938
3. Remove O-ring seals (2) and rings (3) from the displacement change valve.
Illustration 3 g00628657
3/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plugs (5) from the head. Remove an O-ring seal from each plug.
5. Remove outer bolts (4) from the head of the travel motor.
Illustration 4 g00624949
6. Use Tooling (A) and a suitable lifting device to remove the head of the travel motor from
the travel motor housing. The weight of head (6) is approximately 43 kg (95 lb).
Note: There are pins (7) that may fall out of the inside of the head when the head is
removed.
Note: Be careful during the removal of head (6) from the travel motor housing. Be careful
not to scratch mating surfaces or damage the mating surfaces of the components.
4/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g00624953
7. Turn over the head. If pins (7) are in the bottom side of the head, remove the pins.
Illustration 6 g00627405
8. Remove port plate (8) and O-ring seal (9) from the head.
Illustration 7 g00625967
9. Use Tooling (B) in order to remove bearing (10) from the head of the travel motor.
5/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 8 g00627391
10. Remove plate (11) and remove springs (12) from the travel motor housing.
11. Remove O-ring seals (13) from the upper surface of the travel motor housing.
Illustration 9 g00627377
12. Install Tooling (C) on the brake piston (14). Remove the brake piston.
Illustration 10 g00625888
13. Remove O-ring seals (15) and the backup rings from the brake piston.
Note: Make sure that you take note of the location of the O-rings versus the backup rings.
6/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00625891
14. Remove separator plates (16) from the travel motor housing.
Illustration 12 g00666743
15. Remove disks (17) from the travel motor housing.
Illustration 13 g00626837
16. Install Tooling (D) to the shaft and use a suitable lifting device in order to remove the
rotating group from the travel motor housing. The weight of the rotating group is 29 kg
(65 lb).
7/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: Do not allow the components of the rotating group to come apart during the removal
from the travel motor. All of the components in the rotating group must be reinstalled in the
component's original location.
Illustration 14 g00626633
17. Turn over the rotating group. Remove shaft assembly (18) from the rotating group.
Illustration 15 g00666621
Illustration 16 g00625900
18. Use a suitable press to remove bearing (19) from shaft assembly (18).
8/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00666622
19. Use Tooling (E) and a suitable press in order to remove inner race (20) from shaft assembly
(18).
Illustration 18 g00625908
20. Remove cam plate (21) from the rotating group.
Illustration 19 g00625911
21. Retainer (22) and piston assemblies (23) are nonserviceable separately. Prior to the removal
of the retainer and the piston assemblies from barrel (24), put identification marks on the
piston assemblies, the retainer and the barrel for assembly purposes.
9/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 22. The piston assemblies must be reinstalled in the original bores in the retainer and the barrel.
23. Remove retainer (22) and piston assemblies (23) from barrel (24).
24. Separate the piston assemblies from the retainer.
Illustration 20 g00625917
Note: The orientation of the washers (25) is important. The washers must be reinstalled on
barrel (24) in the same orientation.
25. Remove guide (26) and outer spacer (27) from barrel (24).
26. Remove washers (25) and inner spacer (28) from the barrel.
Illustration 21 g00625937
27. Remove keys (29) from the travel motor housing.
10/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00625920
28. Use Tooling (F) to remove retaining ring (30) from the shaft end of the travel motor
housing.
Illustration 23 g00625936
Illustration 24 g00636454
29. Use Tooling (G) to remove lip seal (31) from the travel motor housing if the shaft has been
removed from the travel motor.
11/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 30. Use Tooling (H) to remove lip seal (31) if the shaft has not been removed from the travel
motor. Place the travel motor in a vertical position when you use Tooling (H) to remove the
lip type seal.
Illustration 25 g00625976
31. Remove plug (33) and piston (32) from the travel motor housing. Remove O-ring seal (34)
from the plug.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 27 10:56:16 UTC+0800 2020
12/12
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR TBA
Configuration: 345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i03778971
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
D 4C-8359 Eyebolt 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
J 4C-4030 Thread Lock Compound 1
K 180-6533 Seal Driver 1
L 6V-7030 Micrometer Depth Gauge 1
M 8T-0447 Calipers 1
N 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
1/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-ring seals , gaskets, and seals should always be replaced. A used O-ring seal may not
have the same sealing properties as a new O-ring seal. Use Tooling (H) during the assembly
procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
Illustration 1 g01204890
1. Install O-ring seal (34) on plug (33).
2. Install piston (32) and the plug in the travel motor body. Tighten the plug to a torque of
430 ± 40 N·m (317 ± 30 lb ft).
2/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01204916
Illustration 3 g01204919
3. Apply a thin coat of Tooling (J) on the outer surfaces of lip seal (31).
4. Use Tooling (K) and a suitable hammer to drive the lip seal into the travel motor body.
Drive the seal downward until Tooling (K) makes contact with the travel motor housing.
5. Use Tooling (F) to install retaining ring (30) to the shaft end of the travel motor body.
Illustration 4 g01204923
6. Install keys (29) inside the travel motor body.
3/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g01204924
7. Assemble washers (25), inner spacer (28) and outer spacer (27) in the proper orientation, as
shown.
Illustration 6 g01204931
8. Use Tooling (L) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
4/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g00625917
9. Install inner spacer (28), washers (25), and outer spacer (27) to barrel (24).
10. Install guide (26) to the barrel.
Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24).
Illustration 9 g00625908
12. Install cam plate (21) on the rotating group.
5/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 10 g00666621
Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft assembly (18).
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft assembly (18).
Note: Place the two support plates under the lip of shaft assembly (18).
6/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g00626633
15. Insert shaft assembly (18) in the rotating group.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate disks (17) and separator plates (16) into the travel motor housing. Start with a
separator plate and end with a separator plate.
7/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g01204938
18. Use Tooling (M) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 32.2 ± 2 mm (1.27 ± 0.08 inch).
If this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
8/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
9/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g01204953
21. Use Tooling (M) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1.0 mm (0.82 ± 0.04 inch).
If this measurement is off, drive the brake piston further into the travel motor body.
Illustration 22 g00627391
22. Install springs (12) and plate (11).
10/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 23. Install O-ring seals (13).
Illustration 23 g01204965
24. Use Tooling (G) to drive the bearing into the head.
Illustration 24 g00627405
25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g01205007
11/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. 27. Turn over head (6). Install Tooling (A) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install Pins (7) into the head.
Illustration 27 g00628657
29. Install an O-ring on each plug (5).
30. Install bolts (4) which hold the head in place. Tighten the six bolts to a torque of
530 ± 70 N·m (391 ± 52 lb ft).
31. Install plugs (5) that hold the pins in the head. Tighten the plugs to a torque of 75 ± 7 N·m
(55 ± 5 lb ft).
12/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 28 g00624938
32. Install O-ring seals (2) and rings (3) on the displacement change valve.
Illustration 29 g00627438
33. Install displacement change valve (1) onto the head of the travel motor. Tighten the
displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up
to the fill port prior to operation. Refer to Operation and Maintenance Manual for the
correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 27 10:57:12 UTC+0800 2020
13/13
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engi...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR TBA
Configuration: 345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i02429546
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Threaded Rod
M 20 X 2.5 by 18 inch
2
B 140-7742 Sleeve 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/2
345C & 345C L Excavators TBA00001-UP (MACHINE) POWERED BY C13 Engine...
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...