This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator engines. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head is then removed using lifting equipment. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening the cylinder head bolts in a specific sequence to the correct torques.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...zatao0179249295
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting the cylinder head off. The installation procedure specifies cleaning surfaces, inspecting for damage, selecting the correct gasket, and installing new seals before lowering the cylinder head back into place and reconnecting components. Proper tools are listed for tasks like removing the fuel filter and tapping threads.
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on Caterpillar 345B and 345B L excavator engines. The removal procedure details disconnecting related components and sensors before removing mounting bolts and lifting the cylinder head off. The installation procedure specifies cleaning surfaces, installing new seals, and tightening bolts to specified torques to attach the cylinder head and reinstall any removed components.
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...luanxianshi27
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...wfu089267
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...f8isoeidkdk
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, lifting the cylinder head into place using a device, and torquing bolts to the specified value.
3) References other documents for removing related parts like the valve mechanism cover beforehand.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...zatao0179249295
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting the cylinder head off. The installation procedure specifies cleaning surfaces, inspecting for damage, selecting the correct gasket, and installing new seals before lowering the cylinder head back into place and reconnecting components. Proper tools are listed for tasks like removing the fuel filter and tapping threads.
This document provides instructions for removing and installing the rocker shaft, pushrods, and cylinder head on Caterpillar 345B and 345B L excavator engines. The removal procedure details disconnecting related components and sensors before removing mounting bolts and lifting the cylinder head off. The installation procedure specifies cleaning surfaces, installing new seals, and tightening bolts to specified torques to attach the cylinder head and reinstall any removed components.
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...luanxianshi27
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001...wfu089267
This document provides instructions for removing and installing a cylinder head on a 345B and 345B L excavator engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, lubricating bolts, and tightening the head bolts in a specific sequence to the correct torques.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...f8isoeidkdk
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, lifting the cylinder head into place using a device, and torquing bolts to the specified value.
3) References other documents for removing related parts like the valve mechanism cover beforehand.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 345B excavator engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean surfaces, inspect for damage, and install new gaskets and seals. Specific tightening procedures are outlined for installing the cylinder head and bolts to the correct torques.
Caterpillar cat 345 b excavator (prefix 6xs) service repair manual (6xs00001 ...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent contamination.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. The head bolts are tightened in a specific sequence to torques of 160 Nm initially and 90 degree turns, with some bolts at lower torque. Reinstalled components include water outlets, sensors, and hoses.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
More Related Content
Similar to Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001 and up).pdf
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 345B excavator engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean surfaces, inspect for damage, and install new gaskets and seals. Specific tightening procedures are outlined for installing the cylinder head and bolts to the correct torques.
Caterpillar cat 345 b excavator (prefix 6xs) service repair manual (6xs00001 ...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent contamination.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. The head bolts are tightened in a specific sequence to torques of 160 Nm initially and 90 degree turns, with some bolts at lower torque. Reinstalled components include water outlets, sensors, and hoses.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Similar to Caterpillar Cat 345B L Excavator (Prefix 9GS) Service Repair Manual (9GS00001 and up).pdf (8)
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 9GS
Configuration: 345B and 345B L Excavators 9GS00001-UP (MACHINE)
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i01604601
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00515542
1. Place an identification mark on each rocker arm in order to identify the proper location in
the engine for installation.
2. Remove bolts (1) and rocker arms (2) .
3. Remove push rods (3). Keep each push rod with the respective rocker arm.
Illustration 2 g00515374
4. Remove valve bridges (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 08:07:33 UTC+0800 2020
2/2
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 9GS
Configuration: 345B and 345B L Excavators 9GS00001-UP (MACHINE)
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i07141366
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of the following items: rocker arms, valve bridges, and push rods.
Replace the parts, if necessary.
Illustration 1 g00515542
2. Install push rods (3) in the correct location in the engine.
1/2
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g00515374
3. Install valve bridges (4). Lubricate the top surface of the valve bridges with clean engine oil.
4. Place rocker arms (2) in the correct locations that were marked during removal. Install bolts
(1) and tighten to a torque of 100 ± 20 N·m (74 ± 15 lb ft).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 08:08:30 UTC+0800 2020
2/2
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 9GS
Configuration: 345B and 345B L Excavators 9GS00001-UP (MACHINE)
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i01771996
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Start By:
A. Remove the base for the valve mechanism cover. Refer to Disassembly and Assembly,
"Valve Mechanism Cover Base - Remove and Install".
B. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00517348
1. Remove bolt (1). Remove clip (2) .
2. Disconnect sensors from engine wiring harness (3) .
3. Remove the sensors.
Illustration 2 g00517351
4. Remove bolts (5). Disconnect tube assembly (4) and remove the O-ring seal.
5. Remove bolts (7). Disconnect tube assembly (6) and remove the O-ring seals.
2/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00517354
Typical example
6. Use Tooling (A) in order to remove fuel filter (8). Disconnect hose (9). Plug all openings
immediately.
7. Loosen bolt (11). Disconnect wiring harness (10) .
Illustration 4 g00517355
Typical example
8. Disconnect sensor connector (13) and clips (12). Remove clip (14) and the bolt.
3/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 5 g00517356
Typical example
9. Remove bolts (15) .
10. Remove water outlet manifold (16) .
Illustration 6 g00517359
11. Remove head bolts (17) .
12. Remove water outlet manifold gaskets (18) from cylinder head (19) .
4/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g00517361
13. Attach a suitable lifting device to cylinder head (19). Remove cylinder head (19) from the
cylinder block. The weight of cylinder head (19) is 135 kg (300 lb).
14. Remove cylinder head gasket (20) and O-ring seals (21) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 08:09:26 UTC+0800 2020
5/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 9GS
Configuration: 345B and 345B L Excavators 9GS00001-UP (MACHINE)
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i01792874
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
B 1U-5686 (1)
21/32 inch Drill Bit 1
C 4C-9732 (1)
M16x2.0-D7 Plug Tap 1
D 9U-5604 M16x2.0 32mm Heli-Coil Insert (2)
1
E 8T-2799 (1)
Heli-Coil Installation Tool 1
F 8T-3096 Plug Tap 1
G 6V-4876 Lubricant 1
( 1 )
Part of 4C-8367 Thread Repair Kit
( 2 )
This is a special length.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information, refer to Video Tape, LEVN5101, "C-10 and C-12 Head Gasket Repair
Procedure".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 2. Clean all 26 head bolt holes on the cylinder block with Tooling (F) .
3. After cleaning the threads, remove any debris from the head bolt holes on the cylinder block with a
vacuum line.
4. Visually inspect the head bolt holes on the cylinder block for thread damage.
5. If a damaged head bolt thread is observed, repair the damaged head bolt thread with a Heli-Coil
thread repair kit.
6. Inspect the cylinder head and the cylinder block for flatness. Refer to Guideline for Reusable Parts
and Salvage Operations, SEBF8162, "Procedure to Measure and Salvage Cylinder Head Assemblies
and Related Components".
Illustration 1 g00810396
Cylinder Head Gasket
(29) Straight Edge
2/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g00810399
Cylinder Head Gasket
(28) Scalloped Edge
7. Determine the correct cylinder head gasket to use. Refer to Illustration 1 and Illustration 2.
Illustration 3 g00525775
8. Install the correct cylinder head gasket (26) and new O-ring seals (27) on the cylinder block. Inspect
the condition of the remaining gaskets. Replace the gaskets, if necessary.
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to install
the cylinder head.
9. Use a suitable lifting device to install the cylinder head on the cylinder block.
3/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g00525534
10. Install four gaskets (24) on cylinder head (25) .
11. Install new cylinder head bolts (23). If the engine is equipped with a compression brake, then also
install new head bolt studs.
12. Lubricate the following components with Tooling (G) : the bolt threads, the underside of the bolt
heads and the washers. Follow Step 13 for the correct tightening procedure.
Illustration 5 g00517501
Note: Engines that are equipped with a compression brake will have three head bolt studs. Install the
head bolt studs in positions (2), (8), and (10). Tighten the head bolt studs in sequence with the
cylinder head bolts.
13. Tighten the cylinder head bolts according to the following procedure:
a. Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (120 ±
11 lb ft).
b. Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 160 ± 15 N·m
(120 ± 11 lb ft).
c. Place an index mark on each bolt head. Turn bolt (1) through bolt (26) in a numerical sequence
for an additional 90 degrees (1/4 turn).
4/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. d. Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
e. Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (120 ±
11 lb ft).
f. Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 160 ± 15 N·m
(120 ± 11 lb ft).
g. Place an index mark on each bolt head. Turn bolt (1) through bolt (26) in a numerical sequence
for an additional 90 degrees (1/4 turn).
h. Tighten bolt (27) through bolt (33) in a numerical sequence to a torque of 28 ± 7 N·m (20 ± 5
lb ft).
Illustration 6 g00525468
14. Install head bolt spacers (22) on the three head bolt studs. Tighten head bolt spacers (22) to a torque
of 100 ± 20 N·m (75 ± 15 lb ft).
15. Install water outlet manifold (21) and bolts (20) .
Illustration 7 g00814600
16. Hold line (19) in position and connect fittings (17). Install bolts (18) .
5/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g00676967
17. Connect wiring harness (14). Tighten bolt (16) to a torque of 6 ± 1 N·m (53 ± 9 lb in).
18. Connect hose (15) .
Illustration 9 g00676971
19. Connect sensor connector (12). Install the clip, the washer, and bolt (11). Secure the wiring harness
with tie straps (13) .
20. Install fuel filter (10) with Tool (A). Follow the instructions on the fuel filter.
21. Connect hose (9) .
22. Install hose (8) .
23. Install the bolts, the washers, and two nuts (7) .
6/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g00525386
24. Install tube assembly (5) with the O-ring seals, two bolts (6), and the washers.
25. Install tube assembly (3) with the O-ring seal, two bolts (4), and the washers. Install the clip and the
bolt to tube assembly (5) and (3) .
Illustration 11 g00524436
26. Route wiring harness (1) accordingly and connect sensor connector (2) .
27. Fill the cooling system with coolant to the correct level. Refer to the Operation and Maintenance
Manual for the correct filling procedure.
End By:
a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrods - Install".
b. Install the valve cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 08:10:23 UTC+0800 2020
7/7
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 9GS
Configuration: 345B and 345B L Excavators 9GS00001-UP (MACHINE)
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i02087499
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01022184
1. Remove bolts (1) and lifter assembly (2). The lifter assembly can be removed in two
sections.
Illustration 2 g01022187
2/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 2. Remove the following items from the right end of lifter shaft (5) : bracket assembly (6),
valve lifters (8) and unit injector lifter (9) .
3. Remove the following items from the middle of lifter shaft (5) : valve lifters (8) and unit
injector lifter (9) .
4. Remove the following items from the left end of lifter shaft (5) : bracket assembly (7), valve
lifters (8) and unit injector lifter (9) .
5. Remove dowel (4) and cap plug (3) from lifter shaft (5) .
6. Remove the spring pin from bracket assembly (7), if necessary.
7. Remove dowel (10) from bracket assembly (6), if necessary.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g01022187
1. Install the spring pin and dowel (10) in bracket assembly (6). Install the spring pin and the
dowel in bracket assembly (7) .
2. Install dowel (4) and cap plug (3) in lifter shaft (5). Lubricate the lifter shaft with clean
engine oil prior to assembly.
3. Install the following items on the left end of lifter shaft (5) : bracket assembly (7), valve
lifters (8) and unit injector lifter (9) .
4. Install the following items on the middle of lifter shaft (5) : valve lifters (8) and unit injector
lifter (9) .
5. Install the following items on the right end of lifter shaft (5) : bracket assembly (6), valve
lifters (8) and unit injector lifter (9) .
4/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g01022184
Note: Immerse the entire lifter assembly in clean engine oil prior to installation on the
engine.
6. Place the lifter assembly (2) on the engine and install bolts (1). Tighten the bolts to a torque
of 30 ± 3 N·m (22 ± 2 lb ft).
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 08:11:20 UTC+0800 2020
5/5
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B L EXCAVATOR 9GS
Configuration: 345B and 345B L Excavators 9GS00001-UP (MACHINE)
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i02363444
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 131-1525 Camshaft Pilot 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
B. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
C. Remove the camshaft position sensor. Refer to Disassembly and Assembly, "Camshaft
Position Sensor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1
Piston".
2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the
idler gear and the crankshaft gear.
Illustration 1 g00529917
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
3. Wire the valve lifters away from the camshaft. See Illustration 1.
2/3
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g00813405
4. Remove thrust pin (1) .
5. Install Tooling (A) into camshaft (2) .
Note: Lubricate Tooling (A) for easier removal of the camshaft. Lubrication also prevents
damaging the camshaft lobes and the camshaft bearings.
6. Carefully remove camshaft (2) from the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 13 08:12:17 UTC+0800 2020
3/3
345B and 345B L Excavators 9GS00001-UP (MACHINE)(SEBP2693 - 68) - Docume...
2020/8/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...