This document provides instructions for disassembling and assembling the travel motor on 336F and 336F L excavators. It lists 30 steps for disassembly, removing components like springs, seals, plates, and assemblies. It then lists 29 steps for assembly, reinstalling those components in reverse order and noting specifics like lubrication and torque specifications. The overall document provides detailed technical instructions for fully disassembling and reassembling the travel motor.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...fhhjsjekmdme
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides instructions to reinstall components in their proper positions and orientations. Precautions are described to prevent injury from spring forces. Tools required are listed for both procedures.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...fjsjekkdmnem
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure involves 19 steps and begins with installing O-rings, seals, and pistons before assembling the barrel assembly, rotating assembly, and housing components. Special care must be taken when handling springs or rotating components to avoid injury.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...didkkmmdm
This document provides instructions to disassemble and assemble the travel motor on a 336F L and 336F LN excavator. The disassembly procedure involves removing 30 parts from the travel motor in 29 steps. The assembly procedure involves installing 35 parts into the travel motor in 10 steps, and notes that springs must be installed correctly and tools are needed to install seals and retainers safely.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using tools to set specifications like the lift-off limitation. Precautions are provided to prevent contamination and release of spring forces during the process.
This document provides instructions for assembling the main hydraulic pump of an excavator model. It lists 49 steps and includes illustrations of each step. The steps include installing various parts like bearings, seals, pistons, springs, and valves. Tools needed are also listed. The summary concludes by stating to install the main hydraulic pump by referring to another section of the repair manual.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...fjsqazkekdmme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. It describes 30 steps to disassemble the travel motor, removing components like springs, seals, plates, and housing pieces. It then describes 31 steps to reassemble the travel motor, replacing components in the reverse order and noting specifics like torque settings and lubrication points. The overall document provides detailed instructions to take apart and rebuild the travel motor.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...fhhjsjekmdme
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides instructions to reinstall components in their proper positions and orientations. Precautions are described to prevent injury from spring forces. Tools required are listed for both procedures.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...fjsjekkdmnem
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure involves 19 steps and begins with installing O-rings, seals, and pistons before assembling the barrel assembly, rotating assembly, and housing components. Special care must be taken when handling springs or rotating components to avoid injury.
Caterpillar cat 336 f ln excavator (prefix wtz) service repair manual (wtz000...didkkmmdm
This document provides instructions to disassemble and assemble the travel motor on a 336F L and 336F LN excavator. The disassembly procedure involves removing 30 parts from the travel motor in 29 steps. The assembly procedure involves installing 35 parts into the travel motor in 10 steps, and notes that springs must be installed correctly and tools are needed to install seals and retainers safely.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using tools to set specifications like the lift-off limitation. Precautions are provided to prevent contamination and release of spring forces during the process.
This document provides instructions for assembling the main hydraulic pump of an excavator model. It lists 49 steps and includes illustrations of each step. The steps include installing various parts like bearings, seals, pistons, springs, and valves. Tools needed are also listed. The summary concludes by stating to install the main hydraulic pump by referring to another section of the repair manual.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include:
1. Removing the right side console cover and disconnecting control rods and oil lines from the valve.
2. Removing bolts to take the valve off its mounting bracket.
3. Installing the valve by connecting oil lines and control rods and securing it with bolts back on the bracket.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It also explains how to reinstall these parts in reverse order.
3) Fourteen steps are outlined for removal and thirteen steps for installation, ensuring proper alignment of parts and torquing of bolts.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D7R track-type tractor. It describes 20 steps to disassemble the components and 19 steps to reassemble them. These include removing plates, seals, springs, and other parts, and replacing them in the reverse order. Tools required include link brackets and a driver group. Proper spring loading and seal installation are emphasized.
This document provides instructions for assembling and installing the final drive on a D7R track-type tractor. It describes 31 steps for assembly, including installing seals, bearings, gears, shafts and covers. For installation, it outlines 10 steps such as positioning the final drive, installing bolts, filling it with oil and reconnecting the track. The document contains diagrams to illustrate each step in the process.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...ze3xiandiao
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...ze3xiandiao
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
The document provides instructions for disassembling and assembling the final drives of a D7H track-type tractor. Key steps include removing the final drives from the tractor frame using specialized tools, then disassembling the internal components like planet carriers, gears, shafts, and seals. Reassembly involves heating bearings, installing seals and bearings using presses and tools, and reattaching the final drives to the frame. Precautions are noted to prevent damage to seals during axle removal and installation.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing final drive cases, gears, idler pinions and bearings from a D7G track-type tractor. The steps include:
1) Removing bolts holding the final drive case in position.
2) Installing guide bolts and forcing screws to separate the final drive case from the steering clutch case.
3) Using wire to hold the idler pinion in place so the planet carrier does not fall when the final drive case is removed.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining the oil, removing the sprocket and various components using specialized tools, cleaning seals and surfaces, and installing the new sprocket along with bearings, seals, and other parts in reverse order. Precise measurements and torque specifications are listed to ensure proper installation.
The document provides instructions for removing and installing sprocket assemblies on a direct drive final drive. The key steps include:
1. Draining the oil and removing the sprocket, holder assembly, seals, bearings and other components.
2. Cleaning surfaces and installing new seals before pressing the sprocket onto the hub using a hydraulic press.
3. Reassembling the holder assembly by installing bearings, seals, and adjusting nut then attaching it to the sprocket shaft.
This document provides instructions for removing and installing the engine in a D7F track-type tractor model 94N. The removal process involves draining fluids, disconnecting wiring harnesses and fluid lines, and removing mounting hardware. The engine can then be lifted out of the tractor body. Installation is the reverse of removal, reconnecting all fluid lines, wiring, and securing the engine with mounting hardware. Proper lubrication and adjustment of components is also specified.
This document provides instructions for removing and installing various components of a D7F track-type tractor engine. The components include the timing gear cover, camshaft, flywheel, crankshaft rear seal, power take-off drive gears and bearings, and removing the entire engine. Detailed steps are provided for each component, including preparatory steps, individual installation and removal steps, and concluding steps.
This document provides instructions for disassembling and assembling components of a sleeve metering fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for removing each part and reinstalling them in the proper order.
3) Precautions are outlined, such as ensuring parts are kept with their respective barrels during disassembly and reinstallation.
This document provides instructions to disassemble and assemble the final drive of a D7E track-type tractor. It details 31 steps to disassemble the various components of the final drive including gears, bearings, seals and housings. It then details 22 steps for reassembling the components, noting specific tools and procedures needed such as heating bearings to specific temperatures before installation.
This document provides assembly and disassembly instructions for a D7E track-type tractor final drive. It describes how to assemble the final drive components using various tools, including installing bearings and seals, attaching housing and gear assemblies that weigh up to 880 kg, and tightening bolts to specified torques. The instructions are presented over 29 steps in a precise, sequential order.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include:
1. Removing the right side console cover and disconnecting control rods and oil lines from the valve.
2. Removing bolts to take the valve off its mounting bracket.
3. Installing the valve by connecting oil lines and control rods and securing it with bolts back on the bracket.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
1) The document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor.
2) It describes using various tools to remove over 30 components of the final drive including gears, shafts, seals, and hubs.
3) Precautions are included when using hydraulic cylinders and heated components to disassemble pieces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It also explains how to reinstall these parts in reverse order.
3) Fourteen steps are outlined for removal and thirteen steps for installation, ensuring proper alignment of parts and torquing of bolts.
The document provides instructions for disassembling and assembling the steering clutch and brake of a D7R track-type tractor. It describes 20 steps to disassemble the components and 19 steps to reassemble them. These include removing plates, seals, springs, and other parts, and replacing them in the reverse order. Tools required include link brackets and a driver group. Proper spring loading and seal installation are emphasized.
This document provides instructions for assembling and installing the final drive on a D7R track-type tractor. It describes 31 steps for assembly, including installing seals, bearings, gears, shafts and covers. For installation, it outlines 10 steps such as positioning the final drive, installing bolts, filling it with oil and reconnecting the track. The document contains diagrams to illustrate each step in the process.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...ze3xiandiao
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...ze3xiandiao
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
The document provides instructions for disassembling and assembling the final drives of a D7H track-type tractor. Key steps include removing the final drives from the tractor frame using specialized tools, then disassembling the internal components like planet carriers, gears, shafts, and seals. Reassembly involves heating bearings, installing seals and bearings using presses and tools, and reattaching the final drives to the frame. Precautions are noted to prevent damage to seals during axle removal and installation.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing final drive cases, gears, idler pinions and bearings from a D7G track-type tractor. The steps include:
1) Removing bolts holding the final drive case in position.
2) Installing guide bolts and forcing screws to separate the final drive case from the steering clutch case.
3) Using wire to hold the idler pinion in place so the planet carrier does not fall when the final drive case is removed.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining the oil, removing the sprocket and various components using specialized tools, cleaning seals and surfaces, and installing the new sprocket along with bearings, seals, and other parts in reverse order. Precise measurements and torque specifications are listed to ensure proper installation.
The document provides instructions for removing and installing sprocket assemblies on a direct drive final drive. The key steps include:
1. Draining the oil and removing the sprocket, holder assembly, seals, bearings and other components.
2. Cleaning surfaces and installing new seals before pressing the sprocket onto the hub using a hydraulic press.
3. Reassembling the holder assembly by installing bearings, seals, and adjusting nut then attaching it to the sprocket shaft.
This document provides instructions for removing and installing the engine in a D7F track-type tractor model 94N. The removal process involves draining fluids, disconnecting wiring harnesses and fluid lines, and removing mounting hardware. The engine can then be lifted out of the tractor body. Installation is the reverse of removal, reconnecting all fluid lines, wiring, and securing the engine with mounting hardware. Proper lubrication and adjustment of components is also specified.
This document provides instructions for removing and installing various components of a D7F track-type tractor engine. The components include the timing gear cover, camshaft, flywheel, crankshaft rear seal, power take-off drive gears and bearings, and removing the entire engine. Detailed steps are provided for each component, including preparatory steps, individual installation and removal steps, and concluding steps.
This document provides instructions for disassembling and assembling components of a sleeve metering fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for removing each part and reinstalling them in the proper order.
3) Precautions are outlined, such as ensuring parts are kept with their respective barrels during disassembly and reinstallation.
This document provides instructions to disassemble and assemble the final drive of a D7E track-type tractor. It details 31 steps to disassemble the various components of the final drive including gears, bearings, seals and housings. It then details 22 steps for reassembling the components, noting specific tools and procedures needed such as heating bearings to specific temperatures before installation.
This document provides assembly and disassembly instructions for a D7E track-type tractor final drive. It describes how to assemble the final drive components using various tools, including installing bearings and seals, attaching housing and gear assemblies that weigh up to 880 kg, and tightening bolts to specified torques. The instructions are presented over 29 steps in a precise, sequential order.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR NBL
Configuration: 336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR NBL
Configuration: 336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 20:04:06 UTC+0800 2020
10/10
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F EXCAVATOR NBL
Configuration: 336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07197988
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C 6V-2055 Grease -
D 1P-0510 Driver Gp 1
Illustration 1 g06250080
1. Use a suitable press to press bearing (48) onto shaft (47).
1/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 2 g06249762
Illustration 3 g06250732
Lip seal orientation.
2. Install lip seal (46).
Illustration 4 g06250082
3. Install O-ring seal (45).
4. Use a soft faced hammer to install shaft assembly (44). Install shaft assembly (44) in the
direction that is indicated by the arrow.
2/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Illustration 5 g06249755
Illustration 6 g06249758
5. Use a suitable press and Tooling (D) to install spacers (42), spring (43), and snap ring (41).
3/14
336F & 336F L Excavators NBL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...