The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It outlines 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting out the final drive assembly. For installation, 11 steps are described in reverse order, including positioning the assembly, installing seals and bolts, and reconnecting hoses. Required tools are listed for both procedures.
Caterpillar cat 336 d l excavator (prefix wet) service repair manual (wet0000...fjjskekdm
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists the required tools and gives step-by-step instructions to remove the component by draining fluids, disconnecting hoses, and removing bolts. Instructions are also provided to install the component by replacing seals, positioning the motor, and tightening bolts to the specified torque.
Caterpillar cat 336 d l excavator (prefix wet) service repair manual (wet0000...fjekkdmmem
The document provides instructions for removing the final drive and travel motor assembly from an excavator. It lists the required tools and gives step-by-step instructions involving disconnecting hoses, removing bolts, and lifting the assembly out after applying tension with a lever puller hoist. Identification marks should be made for reinstallation. The process also involves removing travel motor components including O-rings and counterbalance valve.
Caterpillar cat 336 d l excavator (prefix jwr) service repair manual (jwr0000...fjjsekwsxkdmmem
The document provides instructions for removing and installing the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts and brackets, and lifting the assembly out. The installation procedure reverses these steps, adding precautions like checking seals and applying anti-seize compound to bolts. Tools including levers, brackets and a vacuum transducer are required to complete the tasks.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...ze3xiandiao
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar cat 336 d l excavator (prefix wet) service repair manual (wet0000...fjjskekdm
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists the required tools and gives step-by-step instructions to remove the component by draining fluids, disconnecting hoses, and removing bolts. Instructions are also provided to install the component by replacing seals, positioning the motor, and tightening bolts to the specified torque.
Caterpillar cat 336 d l excavator (prefix wet) service repair manual (wet0000...fjekkdmmem
The document provides instructions for removing the final drive and travel motor assembly from an excavator. It lists the required tools and gives step-by-step instructions involving disconnecting hoses, removing bolts, and lifting the assembly out after applying tension with a lever puller hoist. Identification marks should be made for reinstallation. The process also involves removing travel motor components including O-rings and counterbalance valve.
Caterpillar cat 336 d l excavator (prefix jwr) service repair manual (jwr0000...fjjsekwsxkdmmem
The document provides instructions for removing and installing the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts and brackets, and lifting the assembly out. The installation procedure reverses these steps, adding precautions like checking seals and applying anti-seize compound to bolts. Tools including levers, brackets and a vacuum transducer are required to complete the tasks.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...ze3xiandiao
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual (JWR00001...jdkskmmdmd1
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar cat 336 d l excavator (prefix m4t) service repair manual (m4t0000...ikdkdmdm
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and steps to release hydraulic pressure, disconnect hoses, remove mounting bolts, and lift out the final drive assembly. Reinstallation involves cleaning and inspecting seals, positioning the assembly, reattaching hoses, and tightening bolts to the specified torque. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...f8uesjdkdmdm
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...f8uejkkdmdm8u
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...8ufjsekddm8u
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses and fittings, attach lifting devices, and remove mounting bolts. The installation section outlines cleaning and inspecting components, applying anti-seize, and reversing the removal procedures and torque specifications.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...ze3xiandiao
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...f7usuejkdkddm3
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...ufjksemd8ujd
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses and fittings, attach lifting devices, and remove mounting bolts. The installation section outlines cleaning and inspecting components, applying anti-seize, and reversing the removal procedures and torque specifications.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...fujskmd9dokk
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...km7seydwuhdw
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and steps to release hydraulic pressure, disconnect hoses, remove mounting bolts, and lift out the final drive assembly. Reinstallation involves cleaning and inspecting seals, positioning the assembly, reattaching hoses, and tightening bolts to the specified torque. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly process involves removing 37 individual components in a specific order, including gears, shafts, seals, washers, and housings. The assembly section provides instructions for installing these components in reverse order and notes on cleaning, lubricating, and setting proper bearing preload using shims.
Caterpillar Cat 325D L Excavator (Prefix GBR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions to disassemble a final drive over 33 steps. Key steps include removing the cover, gears, carrier assemblies, planetary gears, and seals. Cleanliness is important to prevent dirt entering during disassembly. Various tools are required including a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The total weight of disassembled parts is provided.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual Instant D...fujkskemdmdm4r
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts for a C6.4 engine. It describes the required tools and steps to remove the old inserts and install new ones.
2. Procedures are provided for removing, disassembling, and assembling the engine oil cooler. Parts are to be kept clean from contaminants to prevent damage.
3. Instructions are given for removing and installing the engine oil relief valve, including replacing the gasket. Cleanliness is important to prevent premature wear.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D L excavator. The disassembly process involves using tools to remove retaining rings, seals, bearings, pistons and other components. The assembly process specifies cleaning parts and provides 30 steps for installing components in the correct order and ensuring proper operation, including adjusting end play and installing springs and seals.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions emphasize cleaning parts and ensuring they are reinstalled in their original locations to avoid damage and contamination.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
More Related Content
Similar to Caterpillar Cat 336D L Excavator (Prefix WET) Service Repair Manual Instant Download.pdf
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual (JWR00001...jdkskmmdmd1
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar cat 336 d l excavator (prefix m4t) service repair manual (m4t0000...ikdkdmdm
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and steps to release hydraulic pressure, disconnect hoses, remove mounting bolts, and lift out the final drive assembly. Reinstallation involves cleaning and inspecting seals, positioning the assembly, reattaching hoses, and tightening bolts to the specified torque. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...f8uesjdkdmdm
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...f8uejkkdmdm8u
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...8ufjsekddm8u
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses and fittings, attach lifting devices, and remove mounting bolts. The installation section outlines cleaning and inspecting components, applying anti-seize, and reversing the removal procedures and torque specifications.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...ze3xiandiao
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...f7usuejkdkddm3
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It details 13 steps for removal, including disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. It also details 11 steps for installation, including positioning components, installing seals and bolts, reconnecting hoses, and filling fluids. Safety notices are provided regarding containing fluids and cleaning components.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...ufjksemd8ujd
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes using various tools to disconnect hoses and fittings, attach lifting devices, and remove mounting bolts. The installation section outlines cleaning and inspecting components, applying anti-seize, and reversing the removal procedures and torque specifications.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...fujskmd9dokk
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual (M4T00001...km7seydwuhdw
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and steps to release hydraulic pressure, disconnect hoses, remove mounting bolts, and lift out the final drive assembly. Reinstallation involves cleaning and inspecting seals, positioning the assembly, reattaching hoses, and tightening bolts to the specified torque. Safety notices are provided regarding containing fluids and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Similar to Caterpillar Cat 336D L Excavator (Prefix WET) Service Repair Manual Instant Download.pdf (14)
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly process involves removing 37 individual components in a specific order, including gears, shafts, seals, washers, and housings. The assembly section provides instructions for installing these components in reverse order and notes on cleaning, lubricating, and setting proper bearing preload using shims.
Caterpillar Cat 325D L Excavator (Prefix GBR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions to disassemble a final drive over 33 steps. Key steps include removing the cover, gears, carrier assemblies, planetary gears, and seals. Cleanliness is important to prevent dirt entering during disassembly. Various tools are required including a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The total weight of disassembled parts is provided.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual Instant D...fujkskemdmdm4r
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts for a C6.4 engine. It describes the required tools and steps to remove the old inserts and install new ones.
2. Procedures are provided for removing, disassembling, and assembling the engine oil cooler. Parts are to be kept clean from contaminants to prevent damage.
3. Instructions are given for removing and installing the engine oil relief valve, including replacing the gasket. Cleanliness is important to prevent premature wear.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D L excavator. The disassembly process involves using tools to remove retaining rings, seals, bearings, pistons and other components. The assembly process specifies cleaning parts and provides 30 steps for installing components in the correct order and ensuring proper operation, including adjusting end play and installing springs and seals.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions emphasize cleaning parts and ensuring they are reinstalled in their original locations to avoid damage and contamination.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345D L Excavator (Prefix RAJ) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, plates, seals, and piston assemblies. The disassembly process is described in 31 steps. The assembly section then lists 13 steps to reinstall components in reverse order, making sure to clean parts and apply new seals and lubricants.
This document provides instructions for removing and installing fuel injection pumps and disassembling and assembling fuel ratio control components on a Caterpillar 3406C diesel engine. The steps include using various tools to remove the fuel injection pumps from the pump housing, install new pumps, and check pump installation. Instructions are also provided to disassemble the fuel ratio control housing by removing bolts, springs, diaphragms and other parts and cleaning components before reassembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and replacing removed components.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix WBC) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator powered by a 3306 engine, including:
- Removing the cylinder head by first removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods, then removing bolts and lifting the cylinder head off the engine block.
- Instructions for disassembling, assembling, and installing the rocker shaft, including removing/installing rocker arms, supports, springs and O-rings.
- Steps for installing a compression brake on the engine, including installing brackets, bolts and connecting wires.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 350 and 350 L Excavator (Prefix 3ML) Service Repair Manual In...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the governor of a 350-A excavator powered by a 3306 engine. The disassembly process involves removing 34 parts from the governor including the fuel ratio control, housing, springs, levers, pins, plates, screws, solenoid, shaft and other components. The assembly process describes installing these 34 parts in the reverse order and includes ensuring parts are clean and lubricated before installation. Special tools are required for some steps.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02451126
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 138-7573 Link Bracket 1
Note: Put identification marks on all hose assemblies, fittings and ports so that all the components
can be reassembled in the original configuration. Plug all of the hose assemblies and cap all of the
fittings. This helps to prevent fluid loss and this helps to keep contaminants from entering the
system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/6
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g01223707
2/6
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Remove bolts (1) and cover (2).
2. Separate the track. Refer to Disassembly and Assembly, "Track - Seperate".
Illustration 2 g00944947
3. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 3 g01223711
4. Disconnect hose assemblies (3) and remove fitting (4).
3/6
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g01181911
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb). Put a slight
lifting tension on the final drive and travel motor (5).
Illustration 5 g01181912
6. Remove bolts (6).
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
4/6
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g01181913
7. Use two bolts (6) in order to remove final drive and travel motor (5).
8. Carefully remove final drive and travel motor (5).
9. Remove bolts (6) from the frame.
Illustration 7 g01181914
10. Remove bolts (7) and counterbalance valve (8).
Illustration 8 g01181917
11. Remove O-ring seals (9) and (10).
5/6
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g01181921
12. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
13. Remove bolts (12) that mount travel motor (11) to final drive (13). Remove travel motor
(11).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:40:32 UTC+0800 2020
6/6
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07188136
Final Drive and Travel Motor - Install
SMCS - 4050-012; 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 439-3938 Link Bracket 1
D - Loctite C5A Copper Anti-Seize -
Note: Check the O-ring seals for wear or for damage. Replace the O-ring seals, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01181921
1. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
2. Position travel motor (11). Install bolts (12) that mount travel motor (11) to final drive (13).
2/5
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01181917
3. Install O-ring seals (10) and (9).
Illustration 3 g01181914
4. Install counterbalance valve (8) and bolts (7).
Illustration 4 g01181911
3/5
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 5 g01182266
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb).
6. Carefully position final drive and travel motor (5). Apply Tooling (D) to the threads of bolts
(6).
7. Tighten bolts (6) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
Illustration 6 g01223711
8. Install fitting (4). Connect hose assemblies (3).
4/5
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 7 g00944947
9. Remove Tooling (A). Install the cap onto the hydraulic tank.
10. Fill the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricant Viscosities
and Refill Capacities".
Illustration 8 g01223707
11. Install cover (2) and bolts (1). Tighten bolts (1) to a torque of 130 ± 10 N·m (96 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:41:28 UTC+0800 2020
5/5
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434256
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g01209599
1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216069
2. Disconnect hose assemblies (1), (2), and (3). Remove support (4).
Illustration 3 g01216082
2/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Remove bolts (6) and retainer (8). Remove clamp (7) and boot
(5).
Illustration 4 g01216099
4. Remove bolts (10) and covers (11).
Illustration 5 g01216098
5. Disconnect hose assemblies (15). Disconnect fitting (16). Disconnect hose assemblies (12).
Remove fittings (14). Remove bolts (13). Remove swivel (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:42:24 UTC+0800 2020
3/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02568407
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-3822 Bolt 2
6V-5839 Washer 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 1. Thoroughly clean the outside of the swivel joint prior to disassembly.
Illustration 1 g00633843
Illustration 2 g00633841
2. Use a suitable lifting device to position the swivel joint onto Tooling (B). Fasten the swivel joint to
Tooling (B), as shown. The weight of the swivel joint is approximately 43 kg (95 lb).
3. Remove bolts (1), washers (2), and cover (3) from outside housing (8).
4. Remove O-ring seal (7) from outside housing (8).
5. Remove bolts (4), washers (5), and retainer (6) from rotor (11).
2/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 6. Use Tooling (A) in order to separate the outside housing (8) from rotor (11). The weight of outside
housing (8) is approximately 20 kg (45 lb). The weight of rotor (11) is approximately 21 kg (46 lb).
7. Remove seals (9) from outside housing (8).
8. Remove O-ring seals (10) from the outside housing (8).
9. Remove plug (13). Remove O-ring seal (12) from plug (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:43:21 UTC+0800 2020
3/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02426337
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components,
if necessary.
1/2
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00633843
1. Install O-ring seal (12) on plug (13). Apply clean hydraulic oil on the seal. Install plug (13).
2. Install seals (9) and O-ring seals (10) into outside housing (8).
3. Carefully install outside housing (8) over rotor (11).
4. Install retainer (6), washers (5), and bolts (4). This holds the rotor (11) and the outside housing (8)
together.
5. Apply clean hydraulic oil on O-ring seal (7). Install the O-ring seal in the outside housing.
6. Install cover (3), washers (2), and bolts (1) that secure the cover.
7. Check the swivel joint for leaks. Plug the drain ports of the inside body. Apply shop air pressure in
the top of the swivel joint and check the swivel joint for leaks. The shop air pressure should be
between 0.2758 MPa (40 psi) and 0.4137 MPa (60 psi).
End By:
a. Install the swivel joint. Refer to Disassembly and Assembly, "Swivel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:44:17 UTC+0800 2020
2/2
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434356
Swivel - Install
SMCS - 5060-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Illustration 1 g01216082
1. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Position swivel (9). Install boot (5) and clamp (7). Install
retainer (8) and bolts (6).
1/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01216069
2. Connect hose assemblies (1), (2), and (3). Install support (4).
Illustration 3 g01216098
3. Install bolts (13). Install fittings (14). Install fitting (16). Connect hose assemblies (15).
Connect hose assemblies (14) and (12) to swivel (9).
Illustration 4 g01216099
4. Install covers (11) and bolts (10).
2/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 5 g01209599
5. Remove Tooling (A).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:45:13 UTC+0800 2020
3/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434311
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Remove
SMCS - 5479-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes
for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g00690963
1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the
hydraulic system.
2/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01206719
2. Open door (1).
Illustration 3 g01216136
3. Disconnect harness assemblies (4).
4. Disconnect hose assemblies (2) and (3).
5. Remove bolts (5) and solenoid valve (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 23 11:46:10 UTC+0800 2020
3/3
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR WET
Configuration: 336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434312
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Install
SMCS - 5479-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01216136
1/2
336D L Excavator WET00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...