This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
This document provides instructions for disassembling and assembling a swing motor. It lists the required tools and gives step-by-step procedures for removing and installing parts. Some key steps include removing the head from the motor housing, extracting the piston, and disassembling internal components like plates and springs. Cleanliness is emphasized throughout and O-rings, seals, and other parts should be replaced during reassembly. Proper tooling and procedures are recommended to avoid injury from spring forces.
This document provides instructions for disassembling and assembling a swing motor. It lists the required tools and gives step-by-step procedures for removing and installing parts like the head, pistons, housing, seals, and bearings. Safety notices are included to wear protective equipment when working with spring loaded parts and to keep the system clean to prevent contaminants.
This document provides instructions for disassembling and assembling a swing motor. It lists the required tools and gives step-by-step procedures for removing and installing parts. Some key steps include removing the head from the motor housing, extracting the piston, and disassembling internal components like plates and springs. Cleanliness is emphasized throughout and O-rings, seals, and other parts should be replaced during reassembly. Proper tooling and procedures are recommended to avoid injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix gja) service repair manual (gja000...fjjskekdm
1) The document provides step-by-step instructions for disassembling the travel motor on a 336D2L excavator. It details removing 27 individual components through a series of illustrated steps.
2) Special tools are listed that are required, including various bolts, pins, and bearing pullers. Safety precautions are provided to release spring forces.
3) Each step clearly pictures the component and identifies it by name or number, describing how to remove it from the travel motor assembly. Marks should be made to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix gja) service repair manual (gja000...fjekkdmmem
This document provides instructions for disassembling the travel motor on a 336D2 L excavator. It describes 27 steps to completely disassemble the travel motor. These include removing the motor head assembly, springs, relief valves, plugs, seals, and other internal components. Precautions are provided to protect against potential hazards like released spring forces during disassembly. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
This document provides instructions for disassembling and assembling a swing motor. It includes:
1) A list of required tools for disassembly and assembly.
2) Detailed step-by-step instructions for disassembling the swing motor, removing components like the head, relief valves, pistons, and bearings.
3) Cautions about cleanliness and spring forces during disassembly.
4) Detailed step-by-step instructions for reassembling the swing motor components in reverse order.
This document provides instructions for disassembling and assembling a swing motor. It includes:
1) A list of required tools for disassembly and assembly.
2) Detailed step-by-step instructions for disassembling components like the head, relief valves, piston, barrel, and housing.
3) Cautions about cleanliness and wearing protective equipment when removing springs.
4) Instructions for assembling the components in reverse order and notes about inspecting parts and applying lubricant.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
This document provides instructions for disassembling and assembling a swing motor. It lists the required tools and gives step-by-step procedures for removing and installing parts. Some key steps include removing the head from the motor housing, extracting the piston, and disassembling internal components like plates and springs. Cleanliness is emphasized throughout and O-rings, seals, and other parts should be replaced during reassembly. Proper tooling and procedures are recommended to avoid injury from spring forces.
This document provides instructions for disassembling and assembling a swing motor. It lists the required tools and gives step-by-step procedures for removing and installing parts like the head, pistons, housing, seals, and bearings. Safety notices are included to wear protective equipment when working with spring loaded parts and to keep the system clean to prevent contaminants.
This document provides instructions for disassembling and assembling a swing motor. It lists the required tools and gives step-by-step procedures for removing and installing parts. Some key steps include removing the head from the motor housing, extracting the piston, and disassembling internal components like plates and springs. Cleanliness is emphasized throughout and O-rings, seals, and other parts should be replaced during reassembly. Proper tooling and procedures are recommended to avoid injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix gja) service repair manual (gja000...fjjskekdm
1) The document provides step-by-step instructions for disassembling the travel motor on a 336D2L excavator. It details removing 27 individual components through a series of illustrated steps.
2) Special tools are listed that are required, including various bolts, pins, and bearing pullers. Safety precautions are provided to release spring forces.
3) Each step clearly pictures the component and identifies it by name or number, describing how to remove it from the travel motor assembly. Marks should be made to ensure correct reassembly.
Caterpillar cat 336 d2 l excavator (prefix gja) service repair manual (gja000...fjekkdmmem
This document provides instructions for disassembling the travel motor on a 336D2 L excavator. It describes 27 steps to completely disassemble the travel motor. These include removing the motor head assembly, springs, relief valves, plugs, seals, and other internal components. Precautions are provided to protect against potential hazards like released spring forces during disassembly. Detailed illustrations accompany each step to show how to properly disassemble the travel motor.
This document provides instructions for disassembling and assembling a swing motor. It includes:
1) A list of required tools for disassembly and assembly.
2) Detailed step-by-step instructions for disassembling the swing motor, removing components like the head, relief valves, pistons, and bearings.
3) Cautions about cleanliness and spring forces during disassembly.
4) Detailed step-by-step instructions for reassembling the swing motor components in reverse order.
This document provides instructions for disassembling and assembling a swing motor. It includes:
1) A list of required tools for disassembly and assembly.
2) Detailed step-by-step instructions for disassembling components like the head, relief valves, piston, barrel, and housing.
3) Cautions about cleanliness and wearing protective equipment when removing springs.
4) Instructions for assembling the components in reverse order and notes about inspecting parts and applying lubricant.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing various components of the rear differential and carrier assembly of a Caterpillar 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gearing that allows the rear wheels to turn at different speeds while receiving equal torque.
This document provides instructions for disassembling and assembling the piston pump of a 962K wheel loader steering system. The disassembly procedure has 28 steps that remove components like valves, spools, springs, and bearings. The assembly procedure reverses this with 31 steps, ensuring O-rings and springs are correctly installed to prevent injury. Precautions are provided to safely release spring forces during disassembly and assembly.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which include removing valves, spools, plugs, springs and other components. The assembly section lists 34 steps for reinstalling the parts in reverse order and adjusting axial shaft end play clearance.
This document provides instructions for removing and installing various engine components on a Caterpillar 950B wheel loader, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures describe removing each part, checking part dimensions, cleaning surfaces, lubricating, and correctly installing each part while maintaining proper engine timing. Tools required are also listed.
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, springs, and bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches, and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts and covers.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, idler gear, idler shaft, and front plate. The installation procedure instructs to install the front plate and idler shaft, align the timing marks, and install the idler gear, thrust plate, and idler gear bolt. References are provided for removing and installing the other gears in the front gear group.
The document provides removal and installation instructions for a variable valve actuator oil pressure sensor, variable valve actuator oil pressure solenoid, water pump, water pump disassembly and assembly, water temperature regulator housing, and precooler from a C18 industrial engine. The instructions include lists of required tools and step-by-step procedures with illustrations to guide removal and installation of the components. Safety notices are provided to contain fluids, keep parts clean, and dispose of fluids properly.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torque specifications for installing bolts and nuts.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page document that includes:
1) A list of required tools and safety notices for the removal procedure. The procedure involves removing bolts, lifting devices, and a gasket from the flywheel housing.
2) A list of required tools and safety notices for the installation procedure. The procedure involves cleaning, applying sealant, positioning a gasket and flywheel housing, and tightening bolts in a specific sequence and torque.
3) The document concludes by stating additional installation steps to complete the job.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Removing and installing the fuel priming pump.
- Removing the fuel filter base and disassembling/assembling its components.
- Removing and installing the fuel transfer pump.
- Removing the electronic unit injectors.
The summaries provide concise overviews of the removal and installation procedures for each component in 3 sentences or less.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C18 Industrial Engine, including:
1) Removing and installing the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) Disassembling and assembling the fuel filter base to replace seals and fittings.
3) Procedures include disconnecting fuel lines and electrical connections, marking parts for reinstallation, and applying thread lock compounds. Safety notices advise containing fluids and preventing contamination.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base on the engine and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
The document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger on a C9.3 Industrial Engine. Key steps include draining fluids, removing connecting components, cleaning parts, applying sealants, and torquing fasteners to the specified values. Required tools include pry bars, brushes, vacuum equipment, and wrenches. Cautions are provided regarding containing fluids and preventing contamination.
1. The document provides instructions for removing and installing the crankshaft front seal on a C18 industrial engine.
2. The removal procedure involves using various tools like a slide hammer puller and pry bar to remove the existing seal and wear sleeve.
3. The installation procedure lists the required tools and instructs to use a seal locator, installer, and bolts to properly position and set the new seal and wear sleeve.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C11 engine, including:
1. Removing the rear gear group which involves removing multiple gears, seals, bolts and covers.
2. Removing the flywheel which requires attaching lifting equipment and removing bolts.
3. Installing the rear gear group and flywheel which provides detailed steps and specifications for installing components like bearings and seals.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine, including:
1. Valves, springs, retainers, and rotators. Tools are needed to compress springs during removal and installation.
2. Valve guides. Guides are removed and installed using driver tools to the proper height above the cylinder head.
3. Valve seat inserts. Seat inserts are removed and installed using specialized driver tools for the inlet and exhaust valves.
4. The engine oil filter base and filter. Hoses are disconnected and bolts removed to take off the base and gasket. A strap wrench is recommended to remove the oil filter.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document contains illustrations and lists required tools for each procedure.
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for reinstalling components.
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
This document provides instructions for removing and installing various components of the rear differential and carrier assembly of a Caterpillar 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gearing that allows the rear wheels to turn at different speeds while receiving equal torque.
This document provides instructions for disassembling and assembling the piston pump of a 962K wheel loader steering system. The disassembly procedure has 28 steps that remove components like valves, spools, springs, and bearings. The assembly procedure reverses this with 31 steps, ensuring O-rings and springs are correctly installed to prevent injury. Precautions are provided to safely release spring forces during disassembly and assembly.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the pump which include removing valves, spools, plugs, springs and other components. The assembly section lists 34 steps for reinstalling the parts in reverse order and adjusting axial shaft end play clearance.
This document provides instructions for removing and installing various engine components on a Caterpillar 950B wheel loader, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures describe removing each part, checking part dimensions, cleaning surfaces, lubricating, and correctly installing each part while maintaining proper engine timing. Tools required are also listed.
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, springs, and bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches, and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts and covers.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYG
Configuration: 336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02553557
Swing Motor - Disassemble
SMCS - 5058-015-ZW
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter Kit 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 by 1.75 by 150mm 1
B
6V-7887 Puller Leg 2
5F-7344 Puller Block 1
1P-0074 Slide Hammer Puller Gp 1
5P-4750 Adjusting Screw 1
C
8T-0651 Bolt 2
8T-4167 Hard Washer 2
D 1P-1853 Retaining Ring Pliers 1
E
9S-9152 Bearing Puller Gp 1
1P-0510 Driver Gp 1
Start By:
1/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. a. Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston motors. Refer to Special Publication, SEBD0641,
"Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston motors. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Illustration 1 g00877535
1. Use a suitable lifting device to position swing motor (1) onto Tooling (A). The weight of
swing motor (1) is approximately 77 kg (170 lb). Install swing motor (1) to Tooling (A).
2/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00877536
2. Remove bolts (2). Remove anti-reaction valve (3) from the head.
Illustration 3 g00877537
3. Remove relief valves (4) from the head.
3/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00877538
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove O-ring seals (6), (8), and (9). Remove backup rings (5) and (7).
Illustration 5 g01278075
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove bolts 10.
6. Remove head (11) from the motor housing.
4/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00877540
7. Remove plate (12) and O-ring seal (13).
Illustration 7 g00877541
8. Install Tooling (B) and remove bearing (14).
Illustration 8 g00877542
5/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (15) and the O-ring seal.
Illustration 9 g00877544
10. Remove spring (17) and valve (16).
Illustration 10 g00877545
11. Remove springs (18).
6/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00877546
12. Install Tooling (C). Apply air pressure in order to unseat the piston.
Note: Use air pressure in order to avoid damage to the piston.
Illustration 12 g00877547
13. Remove piston (19).
Illustration 13 g00877548
14. Remove steel plates (20). Remove plates (21).
7/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g00877549
15. Remove barrel (22) and the pistons as an assembly.
Illustration 15 g00877550
16. Mark pistons (23).
17. Remove pistons (23) from barrel (22).
Illustration 16 g00877551
18. Remove pistons (23) from plates (24) and (25).
8/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00877583
19. Separate plates (24) and (25).
Illustration 18 g00877584
20. Use Tooling (D) in order to remove retaining ring (26).
Illustration 19 g00877585
21. Remove plate (28) and shaft (29) from housing (27).
9/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00877589
24. Remove O-ring seal (32) from housing (27).
Illustration 24 g01279836
Illustration 25 g00877629
25. Install Tooling (B). Remove bearing (33) from housing (27).
11/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 ...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g01279840
26. Remove seal (34) from the housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 16:50:53 UTC+0800 2020
12/12
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 ...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYG
Configuration: 336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02554256
Swing Motor - Assemble
SMCS - 5058-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
D 1P-1853 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
1/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01279840
1. Install seal (34) into the housing.
Illustration 2 g01279836
2. Lower the temperature of bearing (33).
3. Install bearing (33) into the housing.
Illustration 3 g00877589
4. Install O-ring seal (32) into housing (27).
2/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00877587
5. Raise the temperature of bearing race (31). Install bearing (31) onto the shaft.
Illustration 5 g00877586
6. Raise the temperature of bearing race (30). Install bearing (30) onto shaft (29).
Illustration 6 g00877585
7. Install shaft (29) and plate (28) into housing (27).
3/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g00877584
8. Use Tooling (D) in order to install retaining ring (26).
Illustration 8 g00877583
9. Reassemble plates (24) and (25).
Illustration 9 g00877551
10. Install pistons (23) into plates (24) and (25).
4/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00877550
11. Install pistons (23) into barrel (22).
Illustration 11 g00877549
12. Install barrel (22) and the pistons as an assembly.
Illustration 12 g00877548
13. Install steel plates (20). Install plates (21).
5/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00877547
14. Install piston (19).
Illustration 14 g00877545
15. Install springs (18).
Illustration 15 g00877544
16. Install valve (16) and spring (17).
6/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 16 g00877542
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install the O-ring seal and plug (15).
Illustration 17 g00877795
18. Lower the temperature of bearing (14). Install bearing (14).
19. Install O-ring seal (13) and plate (12).
7/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g01278075
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Position head (11) onto the motor housing.
21. Install bolts (10).
22. Tighten bolts (10) to a torque of 431 ± 43 N·m (318 ± 32 lb ft).
Illustration 19 g00877538
8/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
23. Install backup up rings (5) and (7). Install O-ring seals (6), (8), and (9).
Illustration 20 g00877537
24. Install relief valves (4) into the head.
25. Tighten relief valves (4) to a torque of 177 N·m (130 lb ft).
Illustration 21 g00877536
26. Position anti-reaction valve (3) onto the head. Install bolts (2).
9/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 22 g00877535
27. Use a suitable lifting device to remove swing motor (1) from Tooling (A). The weight of
swing motor (1) is approximately 77 kg (170 lb).
End By:
a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 16:51:49 UTC+0800 2020
10/10
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 ...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYG
Configuration: 336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02460276
Swing Motor - Install
SMCS - 5058-012-ZW
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Illustration 1 g01210264
1/3
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 1. Attach Tooling (A) and a suitable lifting device to swing motor (12). The weight of swing
motor (12) is approximately 77 kg (170 lb). Install swing motor (12). Install bolts (13).
Illustration 2 g01210258
2. Connect harness assembly (11). Install bolts (10). Connect hose assemblies (8) and (9) .
Illustration 3 g01210219
3. Connect hose assemblies (6) and (7). Tighten hose assemblies (6) and (7) to a torque of 76 ±
4 N·m (56 ± 3 lb ft).
2/3
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 4 g01210215
4. Connect hose assemblies (1), (2), (3), (4), and (5). Tighten hose assemblies (1) and (5) to a
torque of 150 ± 15 N·m (110 ± 12 lb ft). Tighten hose assemblies (2), (3), and (4) to a
torque of 190 ± 20 N·m (140 ± 15 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 16:52:45 UTC+0800 2020
3/3
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYG
Configuration: 336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02460196
Swing Drive - Remove
SMCS - 5459-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 138-7574 Link Bracket 4
C -
Forcing Bolt
M24 x 3 by 5 inch
2
Start By:
A. Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Lower the bucket to the ground.
2. Thoroughly clean the area around the swing drive prior to removal.
3. Drain the oil from the swing drive. Refer to Operation and Maintenance Manual, "Swing
Drive Oil - Change".
Illustration 1 g01206242
4. Use Tooling (A) to remove bolts (1) that secure the swing drive to the main frame.
Illustration 2 g00875735
5. Attach Tooling (B) and a suitable lifting device to swing drive (2), as shown. The weight of
swing drive (2) is approximately 510 kg (1125 lb).
2/3
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 3 g01210665
6. Remove the two corks from the threaded holes in the swing drive housing. Install Tooling
(C) in order to separate the swing drive (2) .
7. Remove swing drive (2) from the machine. The weight of swing drive (2) is approximately
510 kg (1125 lb).
Note: Be careful not to damage pinion gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Aug 20 16:53:42 UTC+0800 2020
3/3
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
31. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR MYG
Configuration: 336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06560081
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 1U-8221 Nylon Sling 1
C 5P-5197 Pliers 1
Start By:
a. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove"
.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
1/8
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00518369
1. Position the swing drive on suitable cribbing, as shown. The weight of the swing drive is
approximately 281 kg (620 lb).
2. Put an alignment mark on the cover and the housing of the swing drive for assembly
purposes.
3. Remove bolts (1) and cover (2).
4. Install Tooling (A) to cover (2).
Illustration 2 g00518372
5. Use a suitable lifting device and Tooling (A) to remove cover (2) from the ring gear of the
swing drive.
2/8
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 3 g00518397
6. Use two people to remove carrier assembly (3). The weight of the carrier assembly is
approximately 23 kg (50 lb).
7. Use the following procedure to disassemble carrier assembly (3).
Illustration 4 g00518398
Illustration 5 g00518400
a. Remove sun gear (4) from carrier assembly (3).
b. Drive spring pin (6) into planetary shaft (5) with a hammer and a punch.
3/8
336D L & 336D LN Excavators MYG00001-UP (MACHINE) POWERED BY C9 En...
2020/8/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...