This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly process similarly provides step-by-step instructions for installing the parts back into the final drive, noting the importance of cleanliness, applying lubricants, and properly setting bearing preloads using shims.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves removing over 30 individual components in a specific sequence. This includes removing gears, shafts, bearings, seals, and housing components. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating, and setting proper bearing preloads using shims. Special tools are required for tasks like installing dual-cone seals.
Caterpillar cat 330 d2 l excavator (prefix zbf) service repair manual (zbf000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. It describes 32 steps to disassemble the final drive by removing gears, shafts, carriers, seals and other components. It then describes 37 steps for reassembling the final drive, including pressing bearings into housings, measuring clearance, installing seals and gears, and torquing bolts. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. The assembly process similarly involves installing the parts in reverse order, applying anti-seize compound, thread lock, and sealant as needed and adjusting bearing preload using shims to achieve the proper clearance. Special tools are required to install dual-cone seals on the sprocket housing and motor housing.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...fujsekmd9idd
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...fuusejkddmmd3e
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix HER) Service Repair Manua...shibi1322
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves removing over 30 individual components in a specific sequence. This includes removing gears, shafts, bearings, seals, and housing components. The assembly process reverses the disassembly steps and provides details on cleaning, lubricating, and setting proper bearing preloads using shims. Special tools are required for tasks like installing dual-cone seals.
Caterpillar cat 330 d2 l excavator (prefix zbf) service repair manual (zbf000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. It describes 32 steps to disassemble the final drive by removing gears, shafts, carriers, seals and other components. It then describes 37 steps for reassembling the final drive, including pressing bearings into housings, measuring clearance, installing seals and gears, and torquing bolts. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. The assembly process similarly involves installing the parts in reverse order, applying anti-seize compound, thread lock, and sealant as needed and adjusting bearing preload using shims to achieve the proper clearance. Special tools are required to install dual-cone seals on the sprocket housing and motor housing.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...fujsekmd9idd
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...fuusejkddmmd3e
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix HER) Service Repair Manua...shibi1322
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly process involves removing 37 individual components in a specific order, including gears, shafts, seals, washers, and housings. The assembly section provides instructions for installing these components in reverse order and notes on cleaning, lubricating, and setting proper bearing preload using shims.
Caterpillar Cat 325D L Excavator (Prefix GBR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions to disassemble a final drive over 33 steps. Key steps include removing the cover, gears, carrier assemblies, planetary gears, and seals. Cleanliness is important to prevent dirt entering during disassembly. Various tools are required including a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The total weight of disassembled parts is provided.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual Instant D...fujkskemdmdm4r
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts for a C6.4 engine. It describes the required tools and steps to remove the old inserts and install new ones.
2. Procedures are provided for removing, disassembling, and assembling the engine oil cooler. Parts are to be kept clean from contaminants to prevent damage.
3. Instructions are given for removing and installing the engine oil relief valve, including replacing the gasket. Cleanliness is important to prevent premature wear.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D L excavator. The disassembly process involves using tools to remove retaining rings, seals, bearings, pistons and other components. The assembly process specifies cleaning parts and provides 30 steps for installing components in the correct order and ensuring proper operation, including adjusting end play and installing springs and seals.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions emphasize cleaning parts and ensuring they are reinstalled in their original locations to avoid damage and contamination.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345D L Excavator (Prefix RAJ) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, plates, seals, and piston assemblies. The disassembly process is described in 31 steps. The assembly section then lists 13 steps to reinstall components in reverse order, making sure to clean parts and apply new seals and lubricants.
This document provides instructions for removing and installing fuel injection pumps and disassembling and assembling fuel ratio control components on a Caterpillar 3406C diesel engine. The steps include using various tools to remove the fuel injection pumps from the pump housing, install new pumps, and check pump installation. Instructions are also provided to disassemble the fuel ratio control housing by removing bolts, springs, diaphragms and other parts and cleaning components before reassembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and replacing removed components.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix WBC) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator powered by a 3306 engine, including:
- Removing the cylinder head by first removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods, then removing bolts and lifting the cylinder head off the engine block.
- Instructions for disassembling, assembling, and installing the rocker shaft, including removing/installing rocker arms, supports, springs and O-rings.
- Steps for installing a compression brake on the engine, including installing brackets, bolts and connecting wires.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 350 and 350 L Excavator (Prefix 3ML) Service Repair Manual In...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the governor of a 350-A excavator powered by a 3306 engine. The disassembly process involves removing 34 parts from the governor including the fuel ratio control, housing, springs, levers, pins, plates, screws, solenoid, shaft and other components. The assembly process describes installing these 34 parts in the reverse order and includes ensuring parts are clean and lubricated before installation. Special tools are required for some steps.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly process involves removing 37 individual components in a specific order, including gears, shafts, seals, washers, and housings. The assembly section provides instructions for installing these components in reverse order and notes on cleaning, lubricating, and setting proper bearing preload using shims.
Caterpillar Cat 325D L Excavator (Prefix GBR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions to disassemble a final drive over 33 steps. Key steps include removing the cover, gears, carrier assemblies, planetary gears, and seals. Cleanliness is important to prevent dirt entering during disassembly. Various tools are required including a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The total weight of disassembled parts is provided.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual Instant D...fujkskemdmdm4r
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts for a C6.4 engine. It describes the required tools and steps to remove the old inserts and install new ones.
2. Procedures are provided for removing, disassembling, and assembling the engine oil cooler. Parts are to be kept clean from contaminants to prevent damage.
3. Instructions are given for removing and installing the engine oil relief valve, including replacing the gasket. Cleanliness is important to prevent premature wear.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D L excavator. The disassembly process involves using tools to remove retaining rings, seals, bearings, pistons and other components. The assembly process specifies cleaning parts and provides 30 steps for installing components in the correct order and ensuring proper operation, including adjusting end play and installing springs and seals.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions emphasize cleaning parts and ensuring they are reinstalled in their original locations to avoid damage and contamination.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345D L Excavator (Prefix RAJ) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, plates, seals, and piston assemblies. The disassembly process is described in 31 steps. The assembly section then lists 13 steps to reinstall components in reverse order, making sure to clean parts and apply new seals and lubricants.
This document provides instructions for removing and installing fuel injection pumps and disassembling and assembling fuel ratio control components on a Caterpillar 3406C diesel engine. The steps include using various tools to remove the fuel injection pumps from the pump housing, install new pumps, and check pump installation. Instructions are also provided to disassemble the fuel ratio control housing by removing bolts, springs, diaphragms and other parts and cleaning components before reassembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and replacing removed components.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix WBC) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator powered by a 3306 engine, including:
- Removing the cylinder head by first removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods, then removing bolts and lifting the cylinder head off the engine block.
- Instructions for disassembling, assembling, and installing the rocker shaft, including removing/installing rocker arms, supports, springs and O-rings.
- Steps for installing a compression brake on the engine, including installing brackets, bolts and connecting wires.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 350 and 350 L Excavator (Prefix 3ML) Service Repair Manual In...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the governor of a 350-A excavator powered by a 3306 engine. The disassembly process involves removing 34 parts from the governor including the fuel ratio control, housing, springs, levers, pins, plates, screws, solenoid, shaft and other components. The assembly process describes installing these 34 parts in the reverse order and includes ensuring parts are clean and lubricated before installation. Special tools are required for some steps.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 L EXCAVATOR SZK
Configuration: 330D2 L Excavator SZK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03508206
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
1/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
2/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
3/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
Illustration 8 g00892975
11. Remove carrier assembly (16).
4/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g01389804
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
5/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
Illustration 14 g00893043
6/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
Illustration 17 g01842974
7/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
9/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 28. Remove bolts (37) from coupling gear (38).
Illustration 24 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
10/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
Illustration 28 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Tue Jun 23 17:22:29 UTC+0800 2020
11/12(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 L EXCAVATOR SZK
Configuration: 330D2 L Excavator SZK00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03949150
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
D 138-7574 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H 5P-3931 Anti-Seize Compound
F 1U-8846 Gasket Sealant
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
1/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counterbore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
2/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8818.5 lb) on
the bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2204.6 ± 220.5 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y) .
Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of the coupling gear (26) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X) .
g. The thickness of the shims is equal to (X - Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
3/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. h. Remove the main housing from the motor housing.
Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18) . Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28) .
4/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 7 g00708214
9. Apply Tooling (H) to the surfaces that contact pins (30) .
10. Install alignment pins (30) .
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26) .
Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
5/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
Illustration 10 g00708187
13. Install gear (26) .
14. Install bolts (25) in gear (26) . Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
6/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 11 g00708186
15. Install O-ring seal (24) to main housing (18) .
Illustration 12 g00708175
16. Assemble carrier assembly (15) , as follows.
Illustration 13 g00708220
a. Install bearings (22) in planetary gear (23) .
7/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 14 g00513451
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
Illustration 15 g00708172
8/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 18. Install a lifting sling through the middle of carrier assembly (15) . Fasten a 12.7 mm (0.50
inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Remove the shackle and the suitable lifting device.
Illustration 16 g00713148
21. Apply Tooling (F) to the mating surface of ring gear (17b) .
22. Install ring gear (17a) on ring gear (17b) .
Illustration 17 g00708184
23. Fasten a suitable lifting device to ring gears (17) , as shown. Install the ring gears to main
housing (18) . The weight of ring gears (17) is approximately 45 kg (100 lb).
9/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 18 g00708325
24. Install spacer (16) in the carrier assembly.
Illustration 19 g00708162
25. Install sun gear (14) in carrier assembly (15) .
Illustration 20 g01304883
10/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 21 g00708218
26. Assemble carrier assembly (7) , as follows.
a. Install bearing (12) in planetary gear (13) .
b. Install thrust washers (11) and planetary gear (13) in the carrier assembly.
c. Install planetary shaft (9) in the carrier assembly.
d. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 22 g00513451
e. Orient the split in spring pin (10) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
27. Repeat Steps 26.a through 26.e in order to install the remaining planetary gears in the carrier
assembly.
11/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 23 g00708092
28. Install carrier assembly (7) in the ring gear. The weight of carrier assembly (7) is
approximately 14 kg (30 lb).
29. Install sun gear (8) in carrier assembly (7) .
30. Install spacer (6) in carrier assembly (7) .
Illustration 24 g00708235
31. Install new O-ring seals (5) on plugs (4) that were in the cover.
12/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Illustration 25 g00708091
32. Install plugs (4) in cover (2) . Tighten plugs (4) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
33. Install thrust plate (3) in cover (2) .
34. Apply Tooling (F) to the mating surface of the ring gear.
Illustration 26 g00708090
35. Fasten Tooling (B) and a suitable lifting device to cover (2) , as shown. The weight of cover
(2) is approximately 32 kg (70 lb). Install cover (2) .
36. Remove Tooling (B) . Install the setscrews in cover (2) .
13/14(W)
w
2020/6/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...