This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools across 35 steps to reinstall the parts in reverse order and adjust bearing preload using shims. Proper cleaning, lubrication and torque specifications are noted throughout.
This document provides disassembly and assembly instructions for the final drive of an excavator model 330F. The disassembly process involves removing 37 individual parts and components of the final drive using various tools. The assembly process describes installing 35 parts in reverse order and adjusting the bearing preload using shims to achieve the proper distance between bearing cone faces. Proper cleaning, lubrication and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves removing 37 individual parts and components of the final drive including gears, shafts, seals, housings and more. The assembly process describes installing these same parts in reverse order and adjusting the bearing preload using shims to achieve the proper clearance between components. Precise tools are required and lubricants should be applied to mating surfaces during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly process involves removing 37 individual parts including gears, shafts, bearings and housings. The assembly process reverses the disassembly with 37 steps, applying sealant and torque specifications where needed to properly reassemble the final drive. Precise measurements and adjustments are required to set the proper bearing preload during assembly.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...shudun96087
This document provides disassembly and assembly instructions for the final drive of a 330D2 excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the final drive assembly including gears, shafts, carriers, seals and housings. The assembly procedure instructs how to reinstall these parts in reverse order and also describes how to properly set the bearing preload using shims.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides details on installing seals, adjusting bearing preload using shims, and torquing bolts to specifications.
This document provides disassembly and assembly instructions for the final drive of a 330D2 excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the final drive assembly including gears, shafts, carriers, seals and housings. The assembly procedure describes installing these parts in reverse order and includes steps to properly set the bearing preload using shims.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...kesi7153062
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides additional details on installing seals, adjusting bearing preload using shims, and torquing bolts.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...cnp692569
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides additional details on installing seals, adjusting bearing preload using shims, and torquing bolts.
This document provides disassembly and assembly instructions for the final drive of an excavator model 330F. The disassembly process involves removing 37 individual parts and components of the final drive using various tools. The assembly process describes installing 35 parts in reverse order and adjusting the bearing preload using shims to achieve the proper distance between bearing cone faces. Proper cleaning, lubrication and torque specifications are noted throughout.
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. The disassembly process involves removing 37 individual parts and components of the final drive including gears, shafts, seals, housings and more. The assembly process describes installing these same parts in reverse order and adjusting the bearing preload using shims to achieve the proper clearance between components. Precise tools are required and lubricants should be applied to mating surfaces during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly process involves removing 37 individual parts including gears, shafts, bearings and housings. The assembly process reverses the disassembly with 37 steps, applying sealant and torque specifications where needed to properly reassemble the final drive. Precise measurements and adjustments are required to set the proper bearing preload during assembly.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...shudun96087
This document provides disassembly and assembly instructions for the final drive of a 330D2 excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the final drive assembly including gears, shafts, carriers, seals and housings. The assembly procedure instructs how to reinstall these parts in reverse order and also describes how to properly set the bearing preload using shims.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides details on installing seals, adjusting bearing preload using shims, and torquing bolts to specifications.
This document provides disassembly and assembly instructions for the final drive of a 330D2 excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the final drive assembly including gears, shafts, carriers, seals and housings. The assembly procedure describes installing these parts in reverse order and includes steps to properly set the bearing preload using shims.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...kesi7153062
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides additional details on installing seals, adjusting bearing preload using shims, and torquing bolts.
Caterpillar Cat 330D2 L Excavator (Prefix HER) Service Repair Manual (HER0000...cnp692569
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 27 different components of the final drive in a specific order. The assembly process reverses the disassembly steps and provides additional details on installing seals, adjusting bearing preload using shims, and torquing bolts.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual (TFG00001...fujsekmd9idd
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) Disassembly involves removing 22 components including bolts, seals, plates, and housing pieces using various tools.
3) Assembly is the reverse of disassembly, applying sealant and torque specifications, and ensuring proper positioning of springs and splines. Cleanliness is emphasized throughout.
Caterpillar Cat 349E L VG Excavator (Prefix KFX) Service Repair Manual (KFX00...fujsekmd9idd
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in the reverse order of disassembly. Tools, specifications, and illustrations are provided to aid the process.
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It details 27 steps to remove components like the motor head assembly, various plugs and seals, springs, valves, and more. Tools required include lifting devices, bolts, nuts, and pullers. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy.
Caterpillar Cat 349E L Excavator (Prefix SPG) Service Repair Manual (SPG00001...fujsekmd9idd
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...fujsekmd9idd
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar Cat 349E L Excavator (Prefix RGH) Service Repair Manual (RGH00001...fujsekmd9idd
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...fujsekmd9idd
This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...fujsekmd9idd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar Cat 349E L Excavator (Prefix ETC) Service Repair Manual (ETC00001...fujsekmd9idd
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and sprocket housing. It then describes the assembly process, providing specifications for torque and installation of components like seals, bearings, bolts, and shims. Precautions are described like applying anti-seize compound and cleaning mating surfaces. Required tools include a transmission repair stand, link brackets, eyebolts, and a duo-cone seal installer.
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. It outlines 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. It then outlines 26 steps for reassembly, providing specifications and torque values for installing components in the reverse order of disassembly, and noting that hydraulic oil must fill the case before operation.
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It describes 22 steps to disassemble the components of the fan drive including removing bolts, seals, retaining rings, discs, and housing parts. It then describes 14 steps for reassembling the fan drive components in reverse order, noting the importance of cleanliness and applying retaining compounds and pressing components together using the appropriate tools.
Caterpillar Cat 349D2 L Excavator (Prefix ZAE) Service Repair Manual (ZAE0000...fujsekmd9idd
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...fujsekmd9idd
This document provides instructions for disassembling and assembling the travel motor of a 349D2 L excavator. It describes 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. The proper tools needed for each step are also listed. Precautions are provided to mark parts locations, contain fluids, and avoid damage or contamination.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...fujsekmd9idd
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, bearing, and more. Safety notices are included to handle parts carefully, avoid damage, clean components properly, and contain fluids.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...fujsekmd9idd
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 29 steps for assembly, installing components like seals, spacers, pistons, and housing pieces in the reverse order of disassembly. Tools required are listed in a table. Cautions are provided about cleanliness, contamination, marking parts locations, and applying lubricant during assembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual (TFG00001...fujsekmd9idd
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) Disassembly involves removing 22 components including bolts, seals, plates, and housing pieces using various tools.
3) Assembly is the reverse of disassembly, applying sealant and torque specifications, and ensuring proper positioning of springs and splines. Cleanliness is emphasized throughout.
Caterpillar Cat 349E L VG Excavator (Prefix KFX) Service Repair Manual (KFX00...fujsekmd9idd
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in the reverse order of disassembly. Tools, specifications, and illustrations are provided to aid the process.
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It details 27 steps to remove components like the motor head assembly, various plugs and seals, springs, valves, and more. Tools required include lifting devices, bolts, nuts, and pullers. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy.
Caterpillar Cat 349E L Excavator (Prefix SPG) Service Repair Manual (SPG00001...fujsekmd9idd
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...fujsekmd9idd
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar Cat 349E L Excavator (Prefix RGH) Service Repair Manual (RGH00001...fujsekmd9idd
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...fujsekmd9idd
This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...fujsekmd9idd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar Cat 349E L Excavator (Prefix ETC) Service Repair Manual (ETC00001...fujsekmd9idd
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and sprocket housing. It then describes the assembly process, providing specifications for torque and installation of components like seals, bearings, bolts, and shims. Precautions are described like applying anti-seize compound and cleaning mating surfaces. Required tools include a transmission repair stand, link brackets, eyebolts, and a duo-cone seal installer.
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. It outlines 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. It then outlines 26 steps for reassembly, providing specifications and torque values for installing components in the reverse order of disassembly, and noting that hydraulic oil must fill the case before operation.
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It describes 22 steps to disassemble the components of the fan drive including removing bolts, seals, retaining rings, discs, and housing parts. It then describes 14 steps for reassembling the fan drive components in reverse order, noting the importance of cleanliness and applying retaining compounds and pressing components together using the appropriate tools.
Caterpillar Cat 349D2 L Excavator (Prefix ZAE) Service Repair Manual (ZAE0000...fujsekmd9idd
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...fujsekmd9idd
This document provides instructions for disassembling and assembling the travel motor of a 349D2 L excavator. It describes 31 steps to disassemble the travel motor by removing components like the head, plates, seals, pins, and piston assemblies. The proper tools needed for each step are also listed. Precautions are provided to mark parts locations, contain fluids, and avoid damage or contamination.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...fujsekmd9idd
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, bearing, and more. Safety notices are included to handle parts carefully, avoid damage, clean components properly, and contain fluids.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...fujsekmd9idd
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 29 steps for assembly, installing components like seals, spacers, pistons, and housing pieces in the reverse order of disassembly. Tools required are listed in a table. Cautions are provided about cleanliness, contamination, marking parts locations, and applying lubricant during assembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 330D2 MOBILE HYD POWER UNIT HER
Configuration: 330D2 L Mobile Hydraulic Power Unit HER00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
330D2 Excavators Machine Systems
Media Number -M0084786-00 Publication Date -01/10/2017 Date Updated -23/10/2017
i03508206
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
1/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
2/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
3/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
Illustration 8 g00892975
11. Remove carrier assembly (16).
4/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g01389804
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
5/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
Illustration 14 g00893043
6/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
Illustration 17 g01842974
7/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
9/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 28. Remove bolts (37) from coupling gear (38).
Illustration 24 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
10/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
Illustration 28 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Mon Jul 13 23:02:02 UTC+0800 2020
11/12(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 330D2 MOBILE HYD POWER UNIT HER
Configuration: 330D2 L Mobile Hydraulic Power Unit HER00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
330D2 Excavators Machine Systems
Media Number -M0084786-00 Publication Date -01/10/2017 Date Updated -23/10/2017
i06146847
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 138-7576 Link Bracket 3
F 138-7574 Link Bracket 2
G
1U-5933 Duo-Cone Seal Installer As 1
169-0503 Installation Kit 1
H 4C-5599 Anti-Seize Compound -
J 9S-3263 Thread Lock Compound -
K 8C-8422 Sealant -
L FT-2770 Leak Down Test Tool 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
any of the seals are damaged, use new parts for replacement. Reassemble the final drive on
Tooling (A) .
1/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g01208879
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) that make contact with the
bearing cups. Install a bearing cup that is in each side of the sprocket housing with a press.
Make sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the motor housing that make contact with bearing
cones (42) .
4. Install inner bearing cone (42) on the motor housing.
Illustration 2 g01208625
5. Attach Tooling (F) and a suitable lifting device to sprocket housing (35) . The weight of
sprocket housing (35) is approximately 109 kg (240 lb). Install sprocket housing (35) on the
motor housing. Carefully install outer bearing cone (42) on the sprocket housing.
2/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct amount of shims (40)
that are required for the proper bearing preload, as follows:
Illustration 4 g01208987
a. Use a depth micrometer in order to measure the step height of coupling gear (38) at
several locations around the gear. Find the average for the measured dimensions
around the gear and record the dimension. Call this Dimension (X) .
b. Apply a load of 4000 kg (8820 lb) to bearing cones (42) .
c. Rotate sprocket housing (35) several times in order to seat the bearing cones.
d. Reduce the load to 3000 ± 300 kg (6615 ± 660 lb).
3/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 5 g00631001
e. While the load is still on the bearing cones, measure the distance between the top face
of the motor housing and the top face of bearing cone (42) . Take measurements in
several locations around the motor housing. Find the average of the measured
dimensions, and record the dimensions. Call this Dimension (Y) .
f. Determine the correct thickness of shims (40) which are used between bearing cone
(42) and coupling gear (38) . Use the following equation in order to determine the
shim pack thickness.
Shim pack thickness ... (Y) − (X) ± 0.05 mm (0.002 inch)
Note: If two shims (40) are required, install the thinnest shim next to coupling gear
(38) during final assembly.
Illustration 6 g01208625
7. Attach Tooling (F) and a suitable lifting device to sprocket housing (35) . Separate sprocket
housing (35) from the motor housing.
ReferenceRefer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that make contact with the seals must be clean and
dry. After installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal
seals.
4/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 7 g00631006
Illustration 8 g01208999
8. Use Tooling (G) to install Duo-Cone seal (43) in the sprocket housing.
Illustration 9 g00631014
5/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 10 g01208626
9. Use Tooling (G) to install Duo-Cone seal (41) in the motor housing.
10. ApplyTooling (H) in the bores for the locating pins that are in the motor housing. Reinstall
the locating pins in the motor housing.
Illustration 11 g01208625
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal (41) or damage the Duo-Cone seal in the main
housing, or the motor housing during assembly of the two components. After installation of
the main housing on the motor housing, there will be a small gap between the components.
The gap between the components is caused by the Duo-Cone seal. This will be eliminated
during the installation of coupling gear (40) .
12. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35) . Carefully install
the sprocket housing on the motor housing.
13. Install outer bearing cone (42) on the sprocket housing. Make sure that the outer bearing
cone is properly seated.
6/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 12 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing. If shims were required, make sure that the thinnest shim is installed on top.
Illustration 13 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position.
Tighten bolts (37) evenly and tighten the bolts in diagonally opposite pairs.
7/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 14 g01208542
17. Install O-ring seal (36) in sprocket housing (35) .
Illustration 15 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) that makes contact with ring
gear (34) .
19. Apply a bead of Tooling (K) on the mating surface of ring gear (34) .
20. Attach Tooling (E) and a suitable lifting device to ring gear (34) . Put ring gear (34) in
position on the sprocket housing. The weight of ring gear (34) is approximately 66 kg (146
lb). Make sure that the alignment mark on the sprocket housing and the ring gear line up
with each other.
Illustration 16 g01843479
8/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 17 g00893674
21. Assemble carrier assembly (28) , as follows.
a. Install bearings (32) in planetary gear (33) .
b. Install thrust washers (31) and planetary gear (33) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (29) in the carrier assembly.
d. Drive spring pin (30) into planetary shaft (29) .
Illustration 18 g00941047
The stake mark is at position (S) .
e. Orient the split in spring pin (30) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.5 mm (0.06 inch) from the
outside diameter of the spring pin hole.
9/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 22. Repeat Steps 21.a through 21.e in order to install the other two planetary gears in the carrier
assembly.
Illustration 19 g01842974
23. Use two people to install carrier assembly (28) . The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 20 g01842853
24. Install spacer (27A) . Install gear (27) .
10/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 21 g00897548
Illustration 22 g00896863
25. Assemble planetary carrier (19) , as follows.
a. Install bearing (25) in planetary gear (26) .
b. Install thrust washers (24) and planetary gear (26) in the planetary carrier.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (22) in planetary carrier (19) .
d. Drive spring pin (23) into planetary shaft (22) .
11/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 23 g00941047
The stake mark is at position (S) .
e. Orient the split in spring pin (23) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.5 mm (0.06 inch) from the
outside diameter of the spring pin hole.
f. Repeat Steps 25.a through 25.e in order to install the other two planetary gears in the
carrier.
Illustration 24 g00893019
26. Position sun gear (20) in planetary carrier (19) and install retaining ring (21) .
12/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 25 g00892997
27. Use Tooling (D) and a suitable lifting device to install planetary carrier (19) into gear (34) .
The weight of planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 26 g00892977
28. Install spacer (18) and gear (17) .
13/18(W)
w
2020/7/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...