1) The document provides assembly instructions for excavator final drive components in 60 steps, requiring various tools and following cleanliness procedures.
2) Key steps include pressing bearings into housings, installing seals, assembling planetary gear carriers, and attaching the final drive housing, cover, and sprocket.
3) Proper bearing preload is set using shims and measurements, and seal integrity is tested with air pressure before installation is complete.
Caterpillar cat 330 d excavator (prefix ffk) service repair manual (ffk00001 ...hhjsekmdmm
1) The document provides assembly instructions for excavator final drive components in 60 steps, requiring various tools and following cleanliness procedures.
2) Key steps include pressing bearings into housings, installing seals, assembling planetary gear carriers, and securing the assembly with bolts torqued to specific values.
3) Final steps include leak testing the seals and installing remaining components like plugs and sprockets. Proper assembly ensures the final drive functions as intended.
Caterpillar cat 330 d l hydraulic excavator (prefix gge) service repair manua...jfdskekdmme
This document provides assembly instructions for excavator final drive models 330D L, 330D N, and 330D LN in 3 sentences:
The instructions list 59 steps and required tools to assemble the final drive components, including installing bearings and seals, assembling carrier assemblies, and testing the final seal. Cleanliness is important during assembly and O-rings, gaskets, and seals should always be replaced with new parts. Dimensions and torque specifications are provided to ensure proper assembly and installation of the final drive.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 329 d l excavator (prefix bfc) service repair manual (bfc0000...ufdjjsjefkkkemm
1) The document provides instructions for servicing the transmission of a 329D L and 329D LN excavator by removing and disassembling the final drive, then reassembling it.
2) 37 steps are outlined for disassembly, which include removing gears, shafts, seals, and other components using various tools.
3) 35 steps are provided for reassembly, including pressing in bearings, measuring clearances, installing seals and pins, and refitting components in reverse order of disassembly. Cleanliness and applying lubricants are emphasized throughout.
Caterpillar cat 330 d l excavator (prefix t2y) service repair manual (t2y0000...fjjskdmnenemm
This document provides assembly instructions for a 330D L excavator final drive. It lists the required tools and parts, and provides step-by-step instructions to assemble the final drive housing, install bearings and seals, attach planetary gears and carriers, and secure the final drive cover. Precise measurements and torque specifications are included to ensure proper assembly and bearing preload. Cleanliness is emphasized throughout the process.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat 325 d l excavator (prefix dbh) service repair manual (dbh0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a multi-step process to disassemble the final drive. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering mechanisms.
Caterpillar cat 330 d excavator (prefix ffk) service repair manual (ffk00001 ...hhjsekmdmm
1) The document provides assembly instructions for excavator final drive components in 60 steps, requiring various tools and following cleanliness procedures.
2) Key steps include pressing bearings into housings, installing seals, assembling planetary gear carriers, and securing the assembly with bolts torqued to specific values.
3) Final steps include leak testing the seals and installing remaining components like plugs and sprockets. Proper assembly ensures the final drive functions as intended.
Caterpillar cat 330 d l hydraulic excavator (prefix gge) service repair manua...jfdskekdmme
This document provides assembly instructions for excavator final drive models 330D L, 330D N, and 330D LN in 3 sentences:
The instructions list 59 steps and required tools to assemble the final drive components, including installing bearings and seals, assembling carrier assemblies, and testing the final seal. Cleanliness is important during assembly and O-rings, gaskets, and seals should always be replaced with new parts. Dimensions and torque specifications are provided to ensure proper assembly and installation of the final drive.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 329 d l excavator (prefix bfc) service repair manual (bfc0000...ufdjjsjefkkkemm
1) The document provides instructions for servicing the transmission of a 329D L and 329D LN excavator by removing and disassembling the final drive, then reassembling it.
2) 37 steps are outlined for disassembly, which include removing gears, shafts, seals, and other components using various tools.
3) 35 steps are provided for reassembly, including pressing in bearings, measuring clearances, installing seals and pins, and refitting components in reverse order of disassembly. Cleanliness and applying lubricants are emphasized throughout.
Caterpillar cat 330 d l excavator (prefix t2y) service repair manual (t2y0000...fjjskdmnenemm
This document provides assembly instructions for a 330D L excavator final drive. It lists the required tools and parts, and provides step-by-step instructions to assemble the final drive housing, install bearings and seals, attach planetary gears and carriers, and secure the final drive cover. Precise measurements and torque specifications are included to ensure proper assembly and bearing preload. Cleanliness is emphasized throughout the process.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat 325 d l excavator (prefix dbh) service repair manual (dbh0000...hfjsekekmmd
The document provides instructions for disassembling a service repair manual for excavator models 325D and 325D L. It lists required tools and a multi-step process to disassemble the final drive. Key steps include removing the final drive cover, carrier assembly, ring gears, and other internal components. Cleanliness is important during disassembly to prevent dirt from entering mechanisms.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and specifies torque values and measurements to ensure proper assembly and bearing clearance is achieved.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...dueikdkmem
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...cdfzxs
This document provides the assembly procedure for an excavator final drive. It lists the required tools and parts. The procedure has 45 steps and includes illustrations of each step. Key steps include pressing bearings into housings, installing seals, assembling the planetary gear carriers, and setting the bearing preload using shims and measurements. Cleanliness is emphasized throughout assembly.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...ikdkdmdm
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...ze3xiandiao
This document provides the assembly procedure for an excavator final drive. It lists the required tools and parts. The procedure has 45 steps and includes illustrations of each step. Key steps include pressing bearings into housings, installing seals, assembling the planetary gear carriers, and setting the bearing preload using shims and measurements. Cleanliness is emphasized throughout assembly.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...fjskekxcddmmme
This document provides the assembly procedure for an excavator final drive. It lists the required tools and parts. The procedure has 45 steps and includes illustrations of each step. Key steps include pressing bearings into housings, installing seals, assembling planetary gear carriers, and setting the final bearing preload using shims and measurements. Cleanliness is emphasized throughout assembly.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...jdkskmdmdm
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies.
3) Cleanliness is emphasized throughout the assembly process to prevent contamination. Measurements are taken and used to set proper bearing preloads.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...fijsekkdmdm2w
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...fskekkdmdmdm3e
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...zan2736ban
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies before installing them into larger transmission components.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts to facilitate installation and prevent corrosion.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...f8sejdkdmdijd
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...f8uesjdkdmdm
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies.
3) Cleanliness is emphasized throughout the assembly process to prevent contamination. Measurements are taken and used to set proper bearing preloads.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...ufs89eodkdmdm
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear carriers.
3) Cleanliness is important during assembly and anti-seize compound should be applied to components before installation.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...jdkskmmdmd1
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear carriers.
3) Cleanliness is important during assembly and anti-seize compound should be applied to components before installation.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...pwg56547003
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...fujkskemdmdm4r
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...f7usuejkdkddm3
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies.
3) Cleanliness is emphasized throughout the assembly process to prevent contamination. Measurements are taken and used to set proper bearing preloads.
Hyster p177 (h3.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes lifting capacities, counterweight weights, tire sizes, fuel and fluid capacities, and electrical specifications for various Hyster truck models. It also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h3.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
More Related Content
Similar to Caterpillar cat 330 d excavator (prefix mey) service repair manual (mey00001 and up)
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and specifies torque values and measurements to ensure proper assembly and bearing clearance is achieved.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...dueikdkmem
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...cdfzxs
This document provides the assembly procedure for an excavator final drive. It lists the required tools and parts. The procedure has 45 steps and includes illustrations of each step. Key steps include pressing bearings into housings, installing seals, assembling the planetary gear carriers, and setting the bearing preload using shims and measurements. Cleanliness is emphasized throughout assembly.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...ikdkdmdm
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission components which include gears, carriers, shafts, seals, and housing, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...ze3xiandiao
This document provides the assembly procedure for an excavator final drive. It lists the required tools and parts. The procedure has 45 steps and includes illustrations of each step. Key steps include pressing bearings into housings, installing seals, assembling the planetary gear carriers, and setting the bearing preload using shims and measurements. Cleanliness is emphasized throughout assembly.
Caterpillar cat 336 d l excavator (prefix ptb) service repair manual (ptb0000...fjskekxcddmmme
This document provides the assembly procedure for an excavator final drive. It lists the required tools and parts. The procedure has 45 steps and includes illustrations of each step. Key steps include pressing bearings into housings, installing seals, assembling planetary gear carriers, and setting the final bearing preload using shims and measurements. Cleanliness is emphasized throughout assembly.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...jdkskmdmdm
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies.
3) Cleanliness is emphasized throughout the assembly process to prevent contamination. Measurements are taken and used to set proper bearing preloads.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...fijsekkdmdm2w
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...fskekkdmdmdm3e
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...zan2736ban
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies before installing them into larger transmission components.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts to facilitate installation and prevent corrosion.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...f8sejdkdmdijd
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...f8uesjdkdmdm
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies.
3) Cleanliness is emphasized throughout the assembly process to prevent contamination. Measurements are taken and used to set proper bearing preloads.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...ufs89eodkdmdm
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear carriers.
3) Cleanliness is important during assembly and anti-seize compound should be applied to components before installation.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...jdkskmmdmd1
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear carriers.
3) Cleanliness is important during assembly and anti-seize compound should be applied to components before installation.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...pwg56547003
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual Instant D...fujkskemdmdm4r
1) The document provides the assembly procedure for a 325D L excavator final drive. It lists the required tools and parts and provides detailed steps and illustrations for assembling the final drive components.
2) Key steps include pressing bearings into housings, measuring bearing preload, installing gears and planetary carrier assemblies, and securing the assembly with bolts.
3) Cleanliness is emphasized throughout assembly and anti-seize compounds are applied to parts before installation to prevent corrosion and ease future maintenance.
Caterpillar Cat 325D L Excavator (Prefix A3R) Service Repair Manual (A3R00001...f7usuejkdkddm3
1) The document provides the assembly procedure for a 325D L excavator transmission. It lists the required tools and parts and provides detailed steps and illustrations for assembling the transmission components.
2) The procedure involves pressing bearings into housings, installing seals, measuring clearances, and assembling planetary gear sets within carrier assemblies.
3) Cleanliness is emphasized throughout the assembly process to prevent contamination. Measurements are taken and used to set proper bearing preloads.
Similar to Caterpillar cat 330 d excavator (prefix mey) service repair manual (mey00001 and up) (19)
Hyster p177 (h3.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes lifting capacities, counterweight weights, tire sizes, fuel and fluid capacities, and electrical specifications for various Hyster truck models. It also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h3.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster n006 (h8.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts9) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake and hydraulic lines
Hyster n006 (h7.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h6.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake lines
Hyster l006 (h7.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities, weights, tire sizes, fuel and fluid capacities
- Engine oil, coolant, transmission oil, hydraulic oil, brake fluid specifications
- Electrical system components and specifications
- Transmission oil pressures
- Hydraulic and steering system relief pressures and components
- Instructions for removing the drive axle assembly, including draining fluids and disconnecting brake, cooling, and drive shaft components.
Hyster l006 (h6.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities and weights for each model
- Tire sizes, fuel capacities, fluid capacities and specifications for various systems
- Transmission oil pressures and relief pressures for hydraulic and steering systems
- Procedures for removing the drive axle, including draining fluids and disconnecting brake, cooling and driveline components.
Hyster k019 (h16 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h14 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h13 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM and H6-H7XM-12EC units.
Hyster k019 (h10 xm 12 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h7 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h6 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM lift trucks.
Hyster k007 (h12 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xms 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D
208-6033 Spanner Socket As 1
208-6034 Spacer 1
E 138-7574 Link Bracket 2
H 6V-7030 Micrometer Depth Gauge Group 1
J FT-2770 Leak Down Test Tool 1
K 1U-6396 O-Ring Assembly Compound 1
L 5P-3931 Anti-Seize Compound 1
M 1U-8846 Gasket Sealant 1
N 8T-9206 Duo-Cone Seal Installer As 1
P 5P-3931 Anti-Seize Compound 1
Q 235-4848 Drill Fixture Gp 1
R 9S-3263 Thread Lock Compound 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring seal may not have
the same sealing properties as a new O-ring. Use Tooling (K) during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
Note: Some of the images that are in this procedure do not show the sprocket assembly that is
attached to the final drive housing. If necessary, the weights that are given include the weight of
the sprocket assembly.
2/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01147975
1. Apply Tooling (P) to the outer diameter of the bearings.
2. Use a suitable press to Install bearings (40) and (41). Make sure that bearing (41) and
bearing (40) contact the counterbore in housing (36).
3. Use Tooling (N) to install Duo-Cone seal (39B).
Illustration 2 g01147981
4. Use Tooling (N) to install Duo-Cone seal (39A) onto housing (38).
Illustration 3 g01147930
3/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 5. Use Tooling (E) and a suitable lifting device to install housing (36) onto housing (38). The
weight of housing (36) is approximately 100 kg (220 lb).
6. Remove Tooling (E) from housing (36).
Illustration 4 g01147724
7. Install stopper plate (35). Do not tighten stopper plate assembly (35) at this time.
Note: Stopper plate (35) will secure housing (36) to housing (38).
8. Install Tooling (E) and a suitable lifting device to housing (36). The combined weight of
housing assembly (36) and (38) is approximately 120 kg (265 lb). Install housing assembly
(36) and (38) in a suitable press.
9. Remove stopper plate (35).
Illustration 5 g01147727
10. Assemble Tooling (D), as shown.
4/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 6 g01147731
11. Install Tooling (D) into housing (36), as shown.
12. Apply a force of 4000 kg (8818 lb) to the top of Tooling (D). Rotate housing (36) to seat the
bearings.
13. Reduce the force on the top of Tooling (D) to 3000 kg (6615 lb).
Illustration 7 g01147737
14. Use Tooling (H) to take a measurement in three locations. Average the three measurements
and record the average measurement as Dimension (W).
15. Remove Tooling (D).
16. Separate Tooling (D).
5/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g01147743
17. Use a micrometer to measure the thickness at three locations of the spacer from Tooling
(D). Record the average measurement as Dimension (X).
Illustration 9 g01147742
18. Use a micrometer to measure the thickness at three locations of stopper plate (35). Record
the average measurement as Dimension (Y).
19. Subtract Dimension (X) from Dimension (Y) and record this figure as Dimension (Z).
Illustration 10 g01147724
6/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 20. Install stopper plate (35) onto housing (38). Do not tighten stopper plate (35) at this time.
Stopper plate (35) will secure the final drive assembly while the final drive assembly is
repositioned onto Tooling (A).
21. Use Tooling (E) and a suitable lifting device to reposition the final drive assembly onto
Tooling (A). The combined weight of housing assembly (36) and (38) is approximately
120 kg (265 lb).
22. Secure the final drive assembly to Tooling (A).
Illustration 11 g01148004
23. Secure the spanner socket from Tooling (D) to stopper plate (35).
24. to determine the final bearing preload, add Dimension (W) to Dimension (Z) and record this
figure as Dimension (V).
25. Use Tooling (H) to measure the distance in three locations.
26. Tighten stopper plate (35) until the average of the measurements is equal to Dimension (V).
27. Remove Tooling (D).
Illustration 12 g01372092
28. Install Tooling (Q) and a suitable vacuum onto stopper plate (35).
7/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 13 g01147789
29. Use a suitable drill and Tooling (Q) to drill a hole to the depth of 15 mm (0.6 inch) in the
stopper plate and in housing (38).
Illustration 14 g01147796
30. Install dowel (37).
Illustration 15 g01147650
31. Apply Tooling (R) to bolts (35A). Install plate (35B) and bolts (35A).
32. Repeat Steps 28 through 31 for the opposite side of stopper plate (35).
8/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 16 g00781807
33. Install O-ring seal (34) on housing (36).
Illustration 17 g00781730
34. Install gear (33) on housing (36).
Illustration 18 g00781719
35. Assemble carrier assembly (27), as follows.
9/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 19 g00781607
a. Use a deburring tool to remove the metal burr from the openings in the carrier.
b. Install two bearings (31) in planetary gear (32).
c. Install thrust washers (30) and planetary gear (32) in the carrier assembly.
d. Install planetary shaft (28) in the carrier assembly.
e. Align the split in spring pin (29) to the top or to the bottom. Make a stake mark on
each side of the spring pin hole in the carrier. Each stake mark should be
approximately 1.50 mm (0.059 inch) from the outside diameter of the spring pin hole.
Illustration 20 g00903073
f. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
36. Repeat Steps 35.a through 35.e to install the other two planetary gears in the carrier.
10/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 21 g00781559
37. Use two people to install carrier assembly (27) in gear (33). The weight of carrier assembly
(27) is approximately 38 kg (85 lb).
Illustration 22 g00781529
38. Install spacer (26). Install gear (25).
Illustration 23 g01148010
39. Assemble carrier assembly (19), as follows.
11/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 24 g00781516
a. Use a deburring tool to remove the metal burr from the openings in the carrier.
b. Install bearing (23) in planetary gear (24).
c. Install thrust washers (22) and planetary gear (24) in the carrier assembly.
d. Install planetary shaft (21) in the carrier assembly.
Illustration 25 g00903073
e. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
12/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 26 g00879368
f. Align the split in the spring pin to the top or to the bottom. Make a stake mark on
each side of the spring pin hole in the carrier. Each stake mark should be
approximately 1.50 mm (0.059 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 39.a through 39.f to install the other two planetary gears in the carrier.
Illustration 27 g01148011
40. Install carrier assembly (19) into gear (33).
41. Install retaining ring (18).
Illustration 28 g00781412
13/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 42. Install spacer (17). Install gear (16).
Illustration 29 g01389598
Note: Make sure that the oil passages in the shafts are oriented toward the center of carrier
assembly (15).
43. Raise the temperature of carrier assembly (15). Lower the temperature of the shafts. Install
the shafts into carrier assembly (15) until the groove of the shafts is at Dimension (A).
Dimension (A) equals 25.00 ± 0.10 mm (0.984 ± 0.004 inch).
44. Make eight stake marks at distance of Dimension (C) from each shaft. Dimension (C)
equals 2.0 ± 1.0 mm (0.08 ± 0.04 inch). The width of each stake mark should be equal to
Dimension (B). Dimension (B) equals 4.0 ± 1.0 mm (0.16 ± 0.04 inch).
14/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 30 g00781407
45. Assemble carrier assembly (15), as follows.
a. Install carrier assembly in position on gear (16).
Illustration 31 g00781401
b. Install retaining ring (14) onto gear (16).
Illustration 32 g00780432
c. Install washer (11). Install bearing assembly (13). Install gear (12). Install washer
(11). Install retaining ring (10) with Tooling (C).
15/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. d. Repeat Steps 45.a through 45.c for the other two planetary gears.
Illustration 33 g00780428
46. Install spacer (9). Install gear (8).
Illustration 34 g00879365
47. Install O-ring seal (7) on plugs (4).
Illustration 35 g00879362
48. Install plugs (4) and spacer (6) in cover (2).
16/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 49. Position gear (5). Install bolts (3).
Illustration 36 g00708090
Illustration 37 g00708089
50. Place a piece of solder in the center of gear (8).
Note: You may need to apply some grease to the solder to keep the solder in position on
gear (8).
51. Use Tooling (B) and a suitable lifting device to Install cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
52. Install four bolts (1) at 90 degrees from each other. Tighten bolts (1) in a crisscross pattern
to a torque of 420 ± 60 N·m (310 ± 44 lb ft). Turn bolts (1) anadditional60 ± 5 degrees.
53. Remove bolts (1).
54. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
55. Use a micrometer to measure the thickness of the solder. Record this measurement to
determine the thickness of the shims for plate (6). Adjust the shims to obtain a clearance of
1.000 + 1.000 mm (0.0394 + 0.0394 inch) between plate (6) and gear (8).
56. Apply Tooling (M) to the mating surfaces of cover (2) and the housing.
17/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 57. Use Tooling (B) and a suitable lifting device to Install cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
58. Apply Tooling (R) to bolts (1). Install bolts (1) and the washers. Tighten bolts (1) in a
crisscross pattern to a torque of 900 ± 100 N·m (664 ± 74 lb ft).
Illustration 38 g00783362
59. Remove plug (4) (not shown). Attach Tooling (J) to cover (2). Reduce the air pressure at the
source to 103 kPa (15 psi). Apply air pressure to Tooling (J). This air will test the Duo-Cone
seals.
60. Use the ball valve on Tooling (J) to eliminate the air pressure to the final drive. A pressure
of 98 kPa (14.2 psi) must be maintained for 30 seconds.
61. Remove Tooling (J). Install plug (6). Torque plug (6) to 80 ± 10 N·m (59 ± 7 lb ft).
62. Remove the final drive from Tooling (A). The weight of the final drive assembly is
approximately 310 kg (683 lb).
End By:
a. If necessary, install the final drive sprocket. Refer to Disassembly and Assembly, "Final
Drive Sprocket - Remove and Install".
b. Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 24 14:52:47 UTC+0800 2020
18/18(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D EXCAVATOR MEY
Configuration: 330D & 330D L Excavators MEY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06252857
Final Drive - Assemble - Type-Two
SMCS - 4050-016
S/N - B6H568-UP
S/N - DTS1-UP
S/N - EAH1-UP
S/N - EDX1-UP
S/N - EFT1-UP
S/N - ERN275-UP
S/N - FAR1-UP
S/N - FFK1-UP
S/N - GGE1-UP
S/N - GGH1-UP
S/N - HHK1-UP
S/N - J2F1-UP
S/N - JBT1-UP
S/N - JLP299-UP
S/N - JTN1-UP
S/N - JWR1-UP
1/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. S/N - XBH1-UP
S/N - YCF1-UP
S/N - ZCT1-UP
S/N - ZML1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 439-3939 Link Bracket 2
D
8T-9206 Duo-Cone Seal Installer As 1
169-0503 Installation Kit 1
E 1U-9895 Crossblock 1
F - Loctite Copper Anti Seize -
G - Loctite 243 -
H - Loctite RTV Silicone Clear -
J FT-2770 Leak Down Test Tool 1
K 6V-2012 Depth Micrometer 1
L 6V-7059 Micrometer 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
any of the seals are damaged, use new parts for replacement.
3/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 1 g03873123
2. Use Tooling (D) to install Duo-Cone seal (45) .
Illustration 2 g03873131
3. Apply Tooling (F) to the surface of dowels (46) . Install dowels (46) .
4. Raise the temperature of lower bearing cone (47) . Install lower bearing cone (47) on motor
housing (48) .
Illustration 3 g03873115
5. Lower the temperature of bearing cups (43) . Install bearing cups (43) in sprocket housing
(41) .
4/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 4 g03873145
6. Use Tooling (D) to install Duo-Cone seal (44) .
Illustration 5 g03873151
7. Attach Tooling (B) and a suitable lifting device to sprocket housing (41) . The weight of
sprocket housing (41) is approximately 110 kg (243 lb). Install sprocket housing (41) .
8. Raise the temperature of upper bearing cone (42) . Install upper bearing cone (42) .
5/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 6 g03873237
Illustration 7 g03873187
9. Use Tooling (E) and a suitable press in order to apply force to upper bearing cone (42) .
Apply a force of 4000 kg (8818 lb) to the top of Tooling (E) . Rotate sprocket housing (41)
in order to seat the roller bearings.
10. Reduce the force on top of Tooling (E) to 3000 ± 300 kg (6614 ± 661 lb). Use Tooling (K)
in order to measure Dimension (X) . Record Dimension (X) .
6/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 8 g03873199
11. Remove Tooling (E) .
12. Use Tooling (K) in order to measure Dimension (W) on coupling gear (39) . Record
Dimension (W) .
Illustration 9 g03873204
Illustration 10 g03873207
7/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 13. Subtract Dimension (X) from Dimension (W) and record the difference as Dimension (V) .
The correct shim thickness is Dimension (V) . Use Tooling (L) in order to measure the
correct thickness of shims (40) . The tolerance of Dimension (V) is 0 ± 0.05 mm (0.0 ±
0.002 inch).
Note: Use a maximum of two shims (40) . If two shims (40) are used to achieve the proper
dimension, install the thinner of the two shims toward coupling gear (39) .
14. Install shims (40) .
15. Apply Tooling (G) to the threads of bolts (38) . Install coupling gear (39) and bolts (38) .
Tighten bolts (38) to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
Illustration 11 g03873246
16. Install O-ring seal (37) in sprocket housing (41) .
17. Thoroughly clean the mating surface of sprocket housing (41) that makes contact with ring
gear (36) .
18. Attach Tooling (A) and a suitable lifting device to ring gear (36) . Put ring gear (36) in
position on sprocket housing (41) . The weight of ring gear (36) is approximately 65 kg
(143 lb). Make sure that the alignment marks on sprocket housing (38) and ring gear (36)
are lined up with each other.
8/27(W)
w
2020/8/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...