Caterpillar cat 330 d2 excavator (prefix hsp) service repair manual (hsp00001 and up)

Service Repair Manual
Models
330D2 and 330D2 L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 EXCAVATOR HSP
Configuration: 330D2 L OEM HSP00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i01219550
Travel Motor - Disassemble
SMCS - 4351-015
S/N - DTG1-UP
S/N - EBP1-UP
S/N - EX71-UP
S/N - FEX1-UP
S/N - HSP1-UP
S/N - JFG1-UP
S/N - KER1-UP
S/N - LJE1-UP
Disassembly Procedure
Start By:
a. Remove the travel motor.
Reference: Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/9(W)
w
2020/7/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
2/9(W)
w
2020/7/16

6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
3/9(W)
w
2020/7/16

11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
4/9(W)
w
2020/7/16

15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
5/9(W)
w
2020/7/16

Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
6/9(W)
w
2020/7/16

20. Remove cam plate (30) from the body of the travel motor.
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
22. Remove O-ring seal (33) from the body of the travel motor.
7/9(W)
w
2020/7/16

23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
25. Remove inner race (37) from shaft (34).
8/9(W)
w
2020/7/16

26. Remove lip seal (38) from the body of the travel motor.
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 16 13:45:11 UTC+0800 2020
9/9(W)
w
2020/7/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11(W)
w
2020/7/16

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11(W)
w
2020/7/16

4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
7. Remove O-ring seals (6) . Remove springs (7) .
3/11(W)
w
2020/7/16

This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11(W)
w
2020/7/16

9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
11. Remove plates (13) and friction discs (14) .
5/11(W)
w
2020/7/16

12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
14. Remove shaft (15) from rotating assembly (16) .
6/11(W)
w
2020/7/16

15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11(W)
w
2020/7/16

18. Remove cam plate (20) from barrel assembly (21) .
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11(W)
w
2020/7/16

20. Remove ball (23) and springs (24) .
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11(W)
w
2020/7/16

25. Remove bolts (29) and cover (30) .
26. Remove seal (31) and backup ring (32) .
27. Remove piston actuator (33) and seal (34) .
10/11(W)
w
2020/7/16

28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 16 13:46:07 UTC+0800 2020
11/11(W)
w
2020/7/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01706705
Travel Motor - Assemble
SMCS - 4351-016
S/N - DTG1-UP
S/N - EBP1-UP
S/N - EX71-UP
S/N - FEX1-UP
S/N - HSP1-UP
S/N - JFG1-UP
S/N - KER1-UP
S/N - LJE1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
1/11(W)
w
2020/7/16

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
4. Install the other retaining ring on the opposite side of bearing (36).
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
2/11(W)
w
2020/7/16

(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
3/11(W)
w
2020/7/16

NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
4/11(W)
w
2020/7/16

Caterpillar cat 330 d2 excavator (prefix hsp) service repair manual (hsp00001 and up)

Recommended

Recommended

More Related Content

More from jfdjskmdmme

More from jfdjskmdmme (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 330 d2 excavator (prefix hsp) service repair manual (hsp00001 and up)