This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator engine. The removal process involves draining coolant, removing various accessories, and using lifting tools to remove the cylinder head. The installation process details cleaning and lubricating parts, torquing bolts in a specific sequence, and reinstalling accessories. Correct timing of gears is emphasized for proper engine function.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 311 d lrr excavator (prefix dwr) service repair manual (dwr00...fjsekdmmeed
This document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and the crankshaft on a Caterpillar C4.2 engine. It outlines the required tools and steps to take the components out and put them back in. Key steps include using a piston ring compressor and socket wrench, cleaning and lubricating parts, aligning marks, and torquing connecting rod nuts. The crankshaft removal involves taking off the oil supply tube, installing a nut, and removing main bearing caps.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjskefkemms
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 315 c excavator (prefix cfb) service repair manual (cfb00001 ...fjsekdmmeed
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing. Assembly is the reverse of disassembly and requires determining the proper shim thickness to set the rolling torque.
3) Special tools are required and components must be cleaned and lubricated before assembly to ensure proper operation of the reassembled final drive.
Caterpillar cat 315 b fm l excavator (prefix 7rz) service repair manual (7rz0...fjsekdmmeed
The document provides instructions for disassembling and assembling track rollers on a 315B excavator. It describes:
1) Removing the track rollers and draining oil from the roller before disassembly.
2) Using presses and tools to remove internal components like seals, shafts, and bearings.
3) Checking shaft end play and installing new internal components in reverse order.
4) Filling the roller with the specified oil and reinstalling it along with the track guide.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...shudun96087
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes how to remove and install the cylinder head, which involves draining coolant, removing accessories, sensors and bolts, and lifting the head off. It also details removing and installing the lifter group by using tools to pull lifters from the cylinder block and lubricating them before replacing in their original locations. Precautions are given to keep parts clean and contain fluids during repair work.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...cnp692569
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...kesi7153062
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...cdfzxs
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for removing and installing the lifter group, including marking lifters for proper placement.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...diskkdkdmdm
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. A separate section provides steps for removing and installing the lifter group, including marking lifters for placement.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual Instant ...f89siekkmdmm2w
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. Additional procedures describe removing and installing the lifter group from the cylinder block.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual Instant ...f8uejkdkdmm3e
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The instructions then specify setting the #1 piston to top center and aligning timing marks before inserting the camshaft. The camshaft is to be lubricated and inserted carefully to avoid damaging lobes or bearings. Finally, components like the front cover are reinstalled.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fuusejkddmmd3e
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. Separate sections provide directions for removing and installing the lifter group.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 311 d lrr excavator (prefix dwr) service repair manual (dwr00...fjsekdmmeed
This document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and the crankshaft on a Caterpillar C4.2 engine. It outlines the required tools and steps to take the components out and put them back in. Key steps include using a piston ring compressor and socket wrench, cleaning and lubricating parts, aligning marks, and torquing connecting rod nuts. The crankshaft removal involves taking off the oil supply tube, installing a nut, and removing main bearing caps.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjskefkemms
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 315 c excavator (prefix cfb) service repair manual (cfb00001 ...fjsekdmmeed
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) Disassembly includes removing 21 components from the final drive housing. Assembly is the reverse of disassembly and requires determining the proper shim thickness to set the rolling torque.
3) Special tools are required and components must be cleaned and lubricated before assembly to ensure proper operation of the reassembled final drive.
Caterpillar cat 315 b fm l excavator (prefix 7rz) service repair manual (7rz0...fjsekdmmeed
The document provides instructions for disassembling and assembling track rollers on a 315B excavator. It describes:
1) Removing the track rollers and draining oil from the roller before disassembly.
2) Using presses and tools to remove internal components like seals, shafts, and bearings.
3) Checking shaft end play and installing new internal components in reverse order.
4) Filling the roller with the specified oil and reinstalling it along with the track guide.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...shudun96087
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes how to remove and install the cylinder head, which involves draining coolant, removing accessories, sensors and bolts, and lifting the head off. It also details removing and installing the lifter group by using tools to pull lifters from the cylinder block and lubricating them before replacing in their original locations. Precautions are given to keep parts clean and contain fluids during repair work.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...cnp692569
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...kesi7153062
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...cdfzxs
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for removing and installing the lifter group, including marking lifters for proper placement.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...jdfjskekmdme
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The camshaft is then removed by loosening bolts while aligning timing marks and lifting it out. Reinstallation requires aligning timing marks, lubricating the camshaft, and tightening bolts to specified torque to complete the job. Proper cleaning and lubrication are emphasized to prevent premature wear.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...diskkdkdmdm
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. A separate section provides steps for removing and installing the lifter group, including marking lifters for placement.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual Instant ...f89siekkmdmm2w
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. Additional procedures describe removing and installing the lifter group from the cylinder block.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual Instant ...f8uejkdkdmm3e
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and removing previous components like the rocker arm shaft and front cover. The instructions then specify setting the #1 piston to top center and aligning timing marks before inserting the camshaft. The camshaft is to be lubricated and inserted carefully to avoid damaging lobes or bearings. Finally, components like the front cover are reinstalled.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fuusejkddmmd3e
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. Separate sections provide directions for removing and installing the lifter group.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual Instant ...shibi1322
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the #1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Similar to Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l00001 and up) (11)
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...udjdkkmdmdm
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes removing the travel motor by draining oil, releasing hydraulic pressure, removing attachment bolts and hoses, and using a hoist. It then describes disassembling and cleaning the travel motor components like the head assembly, valves, cylinders, and seals. The installation and reassembly process is described in reverse order.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...udjdkkmdmdm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar 330L excavator engine. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and properly dispose of fluids.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines. The removal procedure involves using a camshaft bearing tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the engine oil pan and balancer shaft. The installation procedure specifies using the camshaft bearing tool to install the bearings at precise depths and checking the bore size after installation. End steps include reinstalling components like the flywheel housing, balancer shaft, and engine oil pan.
Caterpillar cat 330 l forest swing machines (prefix 8 fk) service repair manu...udjdkkmdmdm
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1) The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2) The installation procedure specifies using the same special tool to install the front, center, and rear balancer shaft bearings at precise depth measurements in the cylinder block.
3) Additional steps include installing the flywheel housing, balancer shaft, and oil pan after checking that the bearing bores are within specification.
Caterpillar cat 330 l excavator (prefix 2 el) service repair manual (2el00001...udjdkkmdmdm
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removing the spacer plate requires removing seals and installing a new gasket when reinstalling.
4. Water directors are removed from the spacer plate and reinstalled at a specified depth in the cylinder head.
5. Lifter group removal involves
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines. The removal procedure involves using a camshaft bearing tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the engine oil pan and balancer shaft. The installation procedure specifies using the same tool to install the bearings at precise depth measurements and ensuring their holes are aligned before reinstalling removed components.
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position.
2. Install the fuel injection pump, O-ring seal, and bushing, and tighten to the specified torque.
3. Use a measurement tool to check that the rack has the correct travel of 15.70 mm after installation.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
This document provides instructions for removing and installing the cylinder head and spacer plate on Caterpillar 330, 330L, and 330LN excavator models. The removal process involves disconnecting various lines and components before removing bolts and lifting the cylinder head off. Installation requires cleaning surfaces, installing gaskets and seals, bolting the head and plate back into place, and reconnecting lines while maintaining proper torque specifications.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...udjdkkmdmdm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...udjdkkmdmdm
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
Caterpillar cat 329 e ln excavator (prefix rld) service repair manual (rld000...udjdkkmdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...udjdkkmdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...udjdkkmdmdm
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service r...udjdkkmdmdm
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...udjdkkmdmdm
This document provides instructions for disassembling and assembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists the required tools and presents 36 steps for disassembly, including removing gears, carriers, seals, and housing components. The final drive assembly weighs approximately 550 kg and its individual parts require lifting devices due to their weights ranging from 32 to 254 kg.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02273201
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
A. Remove the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Remove".
B. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
C. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
D. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
2/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 1 g01063034
2. Remove accessory drive group (1) .
3. Disconnect tube assemblies (3) and (4) .
4. Remove tube assembly (2) .
5. Disconnect hose (5) .
Illustration 2 g01142119
6. Disconnect hose assemblies (6) and (7) .
7. Disconnect the sensors.
8. Attach Tooling (A) and a suitable lifting device to cylinder head (9). The weight of cylinder
head (9) is approximately 147 kg (325 lb).
9. Remove bolts (8). Remove cylinder head (9) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 11 11:13:32 UTC+0800 2020
3/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i05919858
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 4C-5593 Anti-Seize Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Position a new gasket on the engine.
1/5(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g01142119
2. Attach Tooling (A) and a suitable lifting device to cylinder head (9) . The weight of cylinder head (9)
is approximately 147 kg (325 lb). Position the cylinder head onto the dowels in the engine block.
3. Apply Tooling (B) to the threads of bolts (8) . Install bolts (8) .
Tighten the plugs (not shown) for the high-pressure oil gallery on each end of the cylinder head to
the following torque 285 ± 25 N·m (210 ± 18 lb ft).
Note: Refer to Reuse and Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical
Fasteners Used in All Engines" for reuse criteria of bolts (8) .
Illustration 2 g01063104
4. Tighten bolts (8) according to the following procedure:
a. Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (118 ±
11 lb ft).
b. Loosen Bolt (1) through Bolt (26) until the washers are loose under the bolt heads.
2/5(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. c. Tighten Bolt (1) through Bolt (26) again in a numerical sequence to a torque of 160 ± 15 N·m
(118 ± 11 lb ft).
d. Place a mark on Bolt (1) through Bolt (26) .
e. Rotate Bolt (1) through Bolt (26) in a numerical sequence. Rotate the bolts in the clockwise
direction for 90 degrees (1/4 turn) from the mark on the bolts.
f. Loosen Bolt (1) through Bolt (26) until the washers are loose under the bolt heads.
g. Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (118 ±
11 lb ft).
h. Place a mark on Bolt (1) through Bolt (26) .
i. Rotate Bolt (1) through Bolt (26) in a numerical sequence. Rotate the bolts in the clockwise
direction for 90 degrees (1/4 turn) from the mark on the bolts.
j. Tighten Bolt (27) through Bolt (31) in a numerical sequence to a torque of 28 ± 7 N·m (21 ± 5
lb ft).
Tighten the plugs (not shown) for the high-pressure oil gallery on each end of the cylinder
head to the following torque 285 ± 25 N·m (210 ± 18 lb ft).
5. Connect the sensors.
6. Connect hose assemblies (6) and (7) .
3/5(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 3 g01063034
7. Connect hose (5) .
8. Install tube assembly (2) .
9. Connect tube assemblies (3) and (4) .
10. Install accessory drive group (1) .
11. Fill the cooling system. Refer to Operation and Maintenance Manual, "Refill Capacities and
Recommendations".
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
b. Install the alternator. Refer to Disassembly and Assembly, " Alternator - Remove and Install".
c. Install the unit injectors. Refer to Disassembly and Assembly , "Unit Injector - Install".
d. Install the rocker arm and shaft. Refer to Disassembly and Assembly , "Rocker Arm and Shaft -
Install".
Fri Sep 11 11:14:28 UTC+0800 2020
4/5(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i06809044
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 1 g00953158
1. Use Tooling (A) to remove valve lifters (1). Place identification marks on the valve lifters
for installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 1
B 8T-2998 Lubricant 1
2/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 2 g00953158
1. Apply Tooling (B) to valve lifters (1) prior to installation. Use Tooling (A) to install valve
lifters (1) in the original location in the cylinder block.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 11 11:15:24 UTC+0800 2020
3/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02274059
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 12
Start By:
a. Remove the rocker arm and the shaft. Refer to Disassembly and Assembly, "Rocker Arm
and Shaft - Remove".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to reposition the valve lifters out of the way of the camshaft.
2. Set the No. 1 piston to top center on the compression stroke. Refer to Testing and Adjusting,
"Finding Top Center Position for No. 1 Piston".
1/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g01032348
3. Ensure that the timing marks on camshaft gear (1) and idler gear (2) are aligned.
4. Remove bolts (3) and thrust plate (4) from the cylinder block.
Illustration 2 g01032349
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 5. Remove camshaft (5) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 11 11:16:19 UTC+0800 2020
3/3(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i05278252
Camshaft - Install
SMCS - 1210-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 12
B 8T-2998 Lubricant -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g03356215
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: During the installation of the camshaft, rotate the camshaft in both directions in order to
prevent binding in the camshaft bearing bores.
1. Lubricate the camshaft lobes and the valve lifter bore with a 50/50 mixture of Tooling (B). Apply
clean engine oil on the camshaft bearing journals. Carefully install camshaft (10) in the cylinder
block.
2/4(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g03356207
(5) Gear for the high-pressure fuel pump
(6) Camshaft gear
(7) Idler gear
(8) Crankshaft gear
(9) Timing marks
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2. Correct fuel injection timing and correct valve mechanism operation is determined by properly
timing crankshaft gear (8) and camshaft gear (6) to idler gear (7). Also, high-pressure fuel pump gear
(5) must be timed to camshaft gear (6). During installation of the front gear, timing marks (9) on
idler gear (7) must be in alignment with the timing marks on crankshaft gear (8) and the timing
marks on camshaft gear (6). The "0" mark on camshaft gear (6) must align with the timing mark on
idler gear (7). The "V" mark on camshaft gear (6) must align with the "V" mark on fuel pump gear
(5).
3/4(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 3 g01032348
3. Install thrust plate (4) and bolts (3).
4. The maximum permissible end play for a worn camshaft is 0.46 mm (0.018 inch). The maximum
permissible end play for a new camshaft is 0.13 ± 0.08 mm (0.005 ± 0.003 inch).
5. Use Tooling (A) to position the valve lifters in the cylinder block.
6. Calibrate the speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor -
Calibrate".
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the rocker arm and the shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 11 11:17:15 UTC+0800 2020
4/4(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02408922
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g01142107
NOTICE
1/2(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Use a suitable press to remove the camshaft from camshaft gear (1).
Installation Procedure
Note: The temperature of the camshaft gear must not exceed 177 °C (350 °F) during
installation.
1. Raise the temperature of the camshaft gear up to a temperature of 177 °C (350 °F).
2. Align the key in the camshaft with the groove (keyway) in the camshaft gear.
3. Install the camshaft gear on the end of the camshaft.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 11 11:18:11 UTC+0800 2020
2/2(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02545687
Camshaft Bearings - Remove
SMCS - 1211-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
b. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing-
Remove and Install".
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/2(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00633159
1. Use Tooling (A) to remove the camshaft bearings from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 11 11:19:07 UTC+0800 2020
2/2(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B2L
Configuration: 330C Forest Swing Machines B2L00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02545718
Camshaft Bearings - Install
SMCS - 1211-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Camshaft bearings must be installed into their correct position. Failure
to do so will result in engine damage.
1/4(W)
w
2020/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...